Search Documents

By John E. Edkins

Metal sulfides, chiefly pyrite and mFnor sphalerlte zssociated with che Herrin (No. 6) coal member of the Pennsylvania Carbondale Formation, have been concentrated in a coal refuse deposit in southern Illinois. Oxidation of pyrite has produced highly acid waters with high concentrations of iron, zinc (up to 200 parts per million) and toxic trace elements that have leached downward to a water system perched on glacial drift. Chemical, petrographic, low-temperature ashing and x-ray diffraction were performed on cores. The data show that economic recovery of zinc and other trace metals is unlikely at this site. Energy (coal) recovery at the Superior Washer site is possible if resultant environmental problems are considered in the planning.

Jan 1, 1981

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By H. G. Linge

Pyrrhotite (FeS1+x ,0<x<0.15) is an iron sulfide which is considered to be a pest in carbon-in-pulp/ leach (CIP/L) gold processing [l].The perceived influence of pyrrhotite on gold processing by CIP/L is a competing consumption of 02 and CN­as the pyrrhotite dissolves by oxidation [1,2]. The few studies of the oxidation chemistry, kinetics and mechanism of the oxidation ofpyrrhotite are reviewed in detail elsewhere [3].There is broad agreement that the surface of pyrrhotite is very rapidly oxidized to form a thin (e.g. 10 nm) ferric hydroxy-oxide layer which overlays an iron-deficient sulfide lattice covering the original pyrrhotite. The reaction can be summarized thus:

Jan 1, 1995

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By Mathew Cook

Technological developments in Distributed Fiber Optic Sensing and improvements in both hardware and software have allowed fiber optic sensing systems to be deployed in a variety of applications such as pipeline leak detection, perimeter security monitoring, and power cable real time thermal rating. Recently, there has been a larger adoption of monitoring of conveyor belts in so called Conveyor Health Monitiring Systems (CHMS) within the mining and bulk material handling industries to identify idler conditions on an ongoing basis. Several attempts have been made to institute sensing capabilities into conveyors with mixed success. However, recent breakthroughs in modeling, installation methodology, and technology, as well as increased understanding of application and industry requirements, have allowed the technology to be deployed at both experimental and commercial scales. This paper summarizes the application conditions and requirements, design considerations, methodologies used, the outcomes achieved, the logistical and field considerations, and the future possibilities of the use of this technology in CHMS using Distributed Fiber Optic Sensing.

Feb 22, 2026

By Maryam Motamed, Jeremy Stone, Leigh Anne Zhang

Controlling and predicting ground movements are essential to the design of shoring systems. The Courthouse Commons tunnel in San Diego, California, included a 56-foot-deep temporary shaft as a launching point for tunneling using the Sequential Excavation Method (SEM). The rectangular shaft was unique in that it was surcharged on one wall by an 11-story building and employed a hybrid support of excavation design. An array of geotechnical instrumentation was used to monitor lateral and vertical movements at the ground surface. This paper compares the measured ground movement with the predicted ground movement from various excavation stages

Dec 1, 2022

By George C. Toland

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control on the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. This paper discusses the types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent, and discusses in detail technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1975

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By B. Hines

Grinding efficiency in a vertical stirred mill is affected by a wide range of process and mill configuration variables. Of these, the media fill, size, and intrinsic density have a significant effect on power draw and grinding performance. Media-related factors that influence grinding performance include, e.g.,a higher media filling providing additional particle breakage sites, or a lower bead density decreasing the running torque at a given media filling. It has been estimated that the grinding media can cause up to a 30% change in the specific energy required to grind. FLSmidth has generally recommended that the intrinsic density (specific gravity) of the grinding media be more than triple the slurry density. This density difference helps to ensure that sufficient stress intensity is generated in the mill to provide particle breakage. It also reduces the chance of media ?float? if there is a spike in either slurry density or slurry flow rate. The VXPmills have historically operated at slurry density values between 1.2 and 1.5 kg/L, which translates to nominal bead intrinsic density range between 3.6 and 4.5 kg/L. The current trend towards regrinding bulk flotation concentrates to even finer sizes, to improve recoveries of fine grained minerals, has provided motivation to consider closed-circuit operation of stirred media mills. The slurry density in this application is typically higher than in open-circuit operation due to the higher percent solids in cyclone underflows. An additional effect is that closed-circuit operation increases the potential for media float due to higher flow rates as slurry is recycled to the mill. The normal progression in extending the operating range of existing equipment is to carry out laboratory testing before pilot-scale and plant-scale trials. The results presented in this paper examine the media density to slurry density ratio and its effect on grinding performance.

Feb 23, 2014

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By S. M. Woodring

Research objectives included 1) determine relationships if any between spectral response of soil and soil textural groups, Unified Soil Classification subgroups and selected landforms and 2) develop computer assisted techniques for engineering soils mapping of remotely sensed data. The sire in northeastern Kansas, 1.6 Km by 43 Km (1.0 mi by 27 mi), contained glacial and alluvial soils. Multispectral scanner data (0.40 to 1.80 pm) collected at 915 meters altitude (3,000 feet) were analyzed using two distinct computer techniques: the nonsupervised approach involving delineation of soil training areas directly by computer and the supervised approach entailing training area selection manually by the researcher. Computer classification of surface materials follows both methods. Non supervised analysis results failed to show a consistant relation- ship between landform type and soil spectral class. Landforms correlating well displayed either unusually bright or unusually dark spectral signatures. Supervised analysis results showed a strong relationship between soil texture and soil spectral class. A moderately strong tie was shown between engineering soils groups (ML, CL, CH and OH) and their respective spectral classes, and a weak association between landform type and soil spectral class. An analysis procedure for engineering soils mapping by computer of remotely sensed data was developed. 1. Locate cultural features by visual examination of imagery. 2. Produce generalized bare soil-vegetation- water map using nonsupervised technique. 3. Outline significant soil fields for computer training using supervised approach. 4. Computer-classify entire area based on these soil fields.

Jan 1, 1974

By R. A. Matuszak

Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed-torque characteristics to provide an optimum performance from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon&apos; as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far and at the same time improves the performance characteristics.

Jan 1, 1977

By Ulf B. Andersson, Christina Dahnér-Lindkvist, Bruno Figueiredo, Jessa Vatcher, Jonny Sjöberg, Joel Andersson

Hydraulic fracturing to precondition the rock mass in high seismic risk environments has great potential. Unfortunately, there are many unanswered questions about how to best implement a hydraulic fracturing program at individual mine sites, and even how to best use our engineering tools to evaluate these plans. To give the hydraulic fracturing field tests at LKAB’s Kiirunavaara Mine the best chance of success, fully-coupled, discontinuum numerical modelling Itasca’s 3DEC code was used together with statistical simulations of the fracture network. For modelling purposes, it was assumed that hydraulic fracturing successfully reduces seismic risk through 1) the creation of hydraulic fractures along a plane at each injection site, and 2) activation of existing discontinuities. A variety of scenarios for the mine were evaluated, which focused on site specific uncertainties (such as the spacing of the pre-existing discontinuities) and practical solutions (such as the hydraulic fracture spacing, selection of injection medium, and hydraulic fracture site location relative to production). The discrete fracture network (DFN) realizations were developed using available statistical data for discontinuities near where hydraulic fracturing was planned.

Apr 26, 2022

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By Ali Nazem, Rennie Kaunda, Zoheir Khademian, Fei Wang, Raymond Henn, Alex Peretiatkol

"The field demonstration portion of the Underground Grouting and Ground Improvement (UG&GI) short course offered by the Colorado School of Mines was held on May 18, 2016 at Baski Inc.’s Yard in Denver, CO.Numerous full field scale demonstrations of grouting methods and equipment were conducted under various field conditions. As part of these field tests, permeation grouting testing and demonstrations were also conducted. Various cement grout mixes were injected into 1.5-m (60-in.) tall transparent sand columns under controlled conditions (Fig. 1). The objective of the sand column permeation grouting demonstrations in the study was to show students the effects of ordinary Portland cement versus ultrafine cement on the engineering properties of the grout, and the permeation height through various types of soil stratigraphic layers in the sand columns. Similar previous demonstrations have had a specific focus on various brands of Type I-II Portland cements and ultrafine cements with a range of water cement ratios and injection pressures. More detailed information about these previous studies can be found in published proceedings (e.g. Henn et al., 2009 -2011).Equipment and material usedThe five clear plastic sand columns were 191 mm (7.5 in.) inside diameter and 1,524 mm (60 in.) tall. Each sand column had a 19 mm (0.75 in.) diameter hole drilled at the base (bottom) of the blind flange for injection of the grout. A perforated plate and/or screen at the base of the sand columns helped to prevent sand from plugging injection port. A ChemGrout grout plant was used for the demonstration consisting of 0.36 m3 (97 gal) high shear (colloidal) tank mixer, a 0.36 m3 (97 gal) agitator tank and a progressive helical cavity pump with maximum output capacity of 77 L/min (20 gpm) at a maximum discharge pressure of 265 psi (18 bar) (Fig. 2). A simple grout header arrangement consisting of control valves, pressure gauges, flow meter, grout delivery and return line, and a short injection line was also custom built. Also used were infra-red thermometers to measure the temperatures of the grout mix batches, CRD and marsh funnels to measure viscosity, baroid mud balance to measure specific gravity, and a digital scale to measure weights. The grout materials used were Holkim Portand cement (Type I-II), Nippon Steel Sumikin superfine cement and U.S. grout ultrafine cement."

Mar 1, 2017

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By E. Tarshizi

Research was conducted to develop a simulation and animation model for an aggregate (sand and gravel) mine operation. This model can assist the mine engineers to investigate and consider the various options of haulage systems which are critical for the mine operation productivity. Discrete-event system simulation studies can be used for the typical haulage issues that mining engineers are often faced with: using truck fleet haulage, conveyor belts, or a combination of both. The simulation has identified some strengths and weaknesses in the current loading and hauling fleet of the mine, and has resulted in some suggestions for improving the system. The simulation includes animation of the operation. Animation is needed to enhance the benefit of any mine simulation model. By combining the visual power of animation with a mine simulation, a complete picture of the mine system is obtained and displayed. The mine is modeled and animated using GPSS/H® and PROOF Professional®, both of which have shown great applicability in discrete mining simulation projects.

Feb 23, 2014

By KOKOWSKI J., RUDZIŃSKI Ł.

The LUMINEOS network was established in 2013 to monitor mining-induced seismicity in Legnica-Głogów Copper District (LGCD), located in south-western Poland. Since the starting time, the network was improved and today consists of 17 seismometers and 10 accelerometers. Up to now, the strongest recorded earthquake in the region had Mw4.0. Both raw seismic data and earthquakes catalog for events recorded by the LUMINEOS network are fully open and available on the EPISODES platform (https://tcs.ah-epos.eu/#episode:LGCD). During the last 7 years, the network improvements gave us a possibility to increase location accuracy for shallow mining events. This accuracy is influenced by factors such as the configuration of seismic stations, noise level at seismic stations, and the influence of the velocity model. Here we encountered two main issues which are worth to discuss. The first one is the low detection threshold of two seismic stations and their significant impact on the location errors. The second one is the large uncertainty in the S-wave picking. Even though S-waves are not so clearly visible on seismograms, they are very helpful in the estimation of source location and strength of seismic events in the region. In our work, we present the history of LUMINEOS network and corresponding improvement on location accuracy as well as the influence of noisy stations on the error distribution and how it is connected with location results. We also investigate the effect of the S-wave phases and how they are related to the accuracy of the earthquakes locations in the network.

Apr 26, 2022