Search Documents

By M. R. Haibach, M. L. Shema, J. M. Silvis

"Since 2005, longwall coal mine operators in Pennsylvania (US) have been required to collect extensive hydrologic and biological data to document pre- and post-mining conditions of aquatic resources (streams and wetlands) overlying the subsidence control plan areas. Continued operation of the longwall mine is dependent upon empirical data demonstrating that the undermined aquatic resources have either been maintained or restored to an accepted range of pre-mining conditions. This study used quantitative hydrologic methods and comparative biological metrics to examine response of aquatic resources to longwall subsidence at the Bailey Mine located in Greene County, Pennsylvania. This study analyzed data from over 25 miles of streams and over 8 acres of wetlands that traverse the 4,779-acre study area. Hydrologic analysis of flow intermittency suggested that there are variable degrees of change to headwater streams immediately following mining; however, the majority of the effects are reversible through streamflow mitigation measures. Furthermore, the post-mining discharge from streams can be restored to within the range of pre-mining conditions the majority of the time. Biological assessments showed that greater than 95% of assessed stream length has maintained its ability to support benthic macroinvertebrate communities following mining and intervention (i.e., mitigation). Comparative metrics of the benthic macroinvertebrate communities showed that the biological community in 48 of the 50 sample sites is being maintained or restored across both high- and low-gradient streams. The effectiveness of intervention was further substantiated by the similarity in recovery times between streams having no intervention (median = 2.1 years, 95th percentile = 4.9 years) and streams with intervention, when recovery times were measured from the date of the intervention (median = 1.7 years, 95th percentile = 4.7 years). Changes to individual wetlands were observed between the pre- and post-mining assessments, but cumulatively a net gain of 7% in wetland acreage was realized. Hydrologic assessments were used to infer whether there was a potential that streams had been affected by mining; however, the ultimate test of stream recovery is based on biological metrics that establish the relative quality of the biological communities following mining. Overall, the hydrologic balance is being protected and the aquatic life use of streams is being maintained within the Bailey Mine’s subsidence control plan areas."

Jan 1, 2017

By Donivan L. Gordon

One of the several problems facing society today is that of disposing of its solid waste. Each year this nation spends approximately 4.5 billion dollars to collect, transport and dispose of some 360 million tons of domestic and industrial solid waste. Although considerable sums of time and money have been spent in researching various techniques for solid waste disposal, it is presently agreed that sanitary landfilling represents the most economic and universally adaptable solution to the problem of solid waste disposal. However, regardless of the factors favoring sanitary landfilling as the waste disposal method of choice, it should be recognized as carrying with it a potential for the degradation of ground- and surfacewater resources. Through an interdisciplinary effort regulations were promulgated during 1971 in the State of Iowa to govern sanitary disposal projects. Consistent with a set of rationales developed to preserve environmental quality, these regulations set forth hydrologic and geologic standards designed to protect Iowa's water resources. Minimum requirements have been outlined in the regulations through which the natural favorability of potential landfill sites may be evaluated. Natural favorability is primarily defined in terms of the hydrologic and geologic relationships between a proposed landfill site and those in the locality of the site. The regulations specify that leakage from a landfill to a subcropping aquifer must be less than 0.04 cu ft/day/sq ft at the base of the landfill. This factor is offered to quantify the maximum allowable leakage for all sites in unconsolidated sequences underlain by subcropping bedrock aquifers, Based on groundwater research in Iowa, the assumption is made that 50 feet of till will be sufficient to inhibit the downward flow of liquids from a landfill into bedrock aquifers. This assumes a difference of no greater than 40 feet in hydrostatic head between the water table in the unconsolidated sequence and that in the bedrock aquifer. Owing to the fact that bedrock aquifers in many areas of the state are mantled by less than 50 feet of till the regulations provide for site modification, through engineering, to meet the specified leakage standard, In such instances the leakage factor is evaluated by means of the generalized Darcy's Law Q = PIA where:

Jan 1, 1974

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By Duah Philip, Awuah-Offei Kwame

Regulatory pressure to mitigate the cement industry’s environmental impact has intensified recently, spurring innovation in low-carbon cement technologies. In the United States, cement production, consumption, and carbon emissions are accelerating. Despite this trend, the adoption of environmentally friendly dry clinker production technology with combined preheater-precalciner systems has surged from 53.3% in 2002 to 88.5% in 2019. Concurrently, reliance on wet technologies, known for their higher environmental impact, has dropped from 16.5% to 0.6% within the same period. This paper presents the results of our comprehensive study, utilizing over 100 years of industry data, to analyze these technological shifts and their environmental implications.

Feb 1, 2025

By Pramod C. Thakur

During the past ten years, the US coal industry has experimented with various ways to extract methane from coal seams. Drilling long horizontal boreholes in solid coal from mine workings and vertical gob degas boreholes are becoming standard techniques for methane recovery from coal seams. Prime motivations for such work have always been safety and productivity in mines, but the commercial value of gas so produced is encouraging utilization. The paper reviews various ways to produce methane from coal seams and discusses some utilization projects extant in the industry.

Jan 1, 1984

By William P. Lorenz

Overlying the sulfide mineralization at Anamax Mining Company's Twin Buttes Mine is an oxidized zone up to one hundred meters in thickness. The principal copper minerals in this zone are chryso-colla, tenorite, cuprite, native copper and copper-manganese-iron wad. This ox¬idized zone also contains minor amounts of uranium ranging in concentration from 0.002 to 0.010 percent. Since pit development through 1980, some 38 million tonnes of oxide ore with copper contents greater than 0.6 percent have been brought to the surface. Copper in the oxide ore is extracted at Twin Buttes in, an agitated sulfuric acid leach plant followed by solvent extraction and electrowinning producing 90 tonnes per day of copper cathode. During leaching of the oxide ores small amounts of uranium are solubilized along with the copper values. This is not limited to Twin Buttes as most acidic copper bearing leach solutions throughout the southwestern United States contain small amounts of uranium.1

Jan 1, 1982

By Gary Peach, Peter Mason

Planning and estimating progress rates and costs for tunnelling is always best done based on experience and historic precedent. Much precedent is available but the use of data monitoring, data mining and other retrieval techniques on modern TBM machines can enable this to be further expanded and refined. Advance rates can be related much more closely to rock types as can associated rock bolt and mesh/ shotcrete requirements. This in turn can lead to a further refinement in best likely combinations of equipment, such as shotcrete jumbos, better selected for the anticipated conditions, rather than the potential advance rates of the machine. Efficient and timely construction of the tunnel will also be linked to times needed for finishing work, such as contact and void grouting and to how this can be initiated while the TBM is still in operation, in order to save overall construction time. Indeed, this in turn may affect the most preferable layout and construction details of the permanent tunnel. Considerable experience has been gained in the use of two large diameter TBM tunnel drives through the Himalayas at the Neelum-Jhelum hydropower project in Pakistan. All the above aspects will be discussed in the paper based on the considerable experience and data which came from that operation, including appropriate measures in highly stressed areas potentially subject to rock burst.

Jun 13, 2021

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By R. E. Hamilton

Automation is a word whose meaning has been broadened by popular usage to include any labor saving device. We with restrict our usage to the replacement of human judgement by instrumental measurement and mathematical analysis in the control of industrial processes. Mineral concentration is an area which has resisted automation because of the great difficulty in developing measuring instruments which can exist in the rugged environment and can measure useful properties with acceptable accuracy. This is not the only factor limiting progress, but until recently it has been of over-whelming importance. The development of on-stream X-ray analysers, magnetic flowmeters and nuclear density meters for mineral slurries has eliminated this obvious barrier and is enabling us to locate and attack the less obvious problems which still limit our ability to automate concentrators. If we examine the history of automation in industries which are highly automated we find that it has usually gone through three distinct phases. The first phase has been regulation. This is the simplest form of control and involves manipulating some variable whose value is of no importance in order to maintain the value of some other variable which is important at a constant specified value in spite of disturbances which may occur in other variables which affect it. A simple example is the use of a control valve to maintain a constant flow of fluid in a line in spite of changes in pressure in the vessels at the ends of the line. The position of the valve stem is of no consequence, as long as it is within its operating range. Unfortunately we soon run out of variables which can be

Jan 1, 1971

By Wayne A. Van Voast

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 1,250 m3/day of flow from storage and created a piezometric depression of 3 meters or more as far as 1,500 meters from the mine. No wells have yet become non-productive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures or ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand, silt, and clay. Hydraulic conductivities and storage coefficients are comparable with those of undisturbed confined aquifers. Water quality in mined lands is highly diverse because of diverse spoils lithologies and poorly-established ground-water circulation. Ground water in spoils is more mineralized than in the coal beds and chemically resembles waters from sandstone aquifers. Hydrologic effects of mining will not be catastrophic or widespread but may have local significance. Most notable changes will be in water quality; availability will not be permanently reduced.

Jan 1, 1978

By T. A. Ring

The bed filtration of colloidal particles has been modeled by performing a differential particle balance. The balance considered the localized particle deposition rate to be the sum of three rate resistances: 1) mass transfer to a region near the surface; 2) adhesion onto a partially filled surface; and 3) resuspension from a partially filled surface. The differential particle balance equations, one for the free particles and one for the adhered particles, were solved by a finite difference algorithm. The results of this model are compared to experimental filter breakthrough curves.

Jan 1, 1983

By Richard H. Johnson

White Pine Copper Company, a subsidiary of Copper Range Company located in Michigan's Upper Peninsula, mines a Precambrian sedimentary deposit containing finely disseminated chalcocite, native cop- per and native silver. Silver occurs predominately in certain strata and presently provides a mill head averaging 0.25 ounces per ton. This technical publication traces the development of silver recovery at White Fine beginning in early 1961. White Pine refined copper contains an excess of silver over and above that required to impart Lake Copper properties. The copper does not require electrolytic refining to meet industry purity requirements, nor is there sufficient silver to justify electrolysis.

Jan 1, 1970

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of fluorspar from 35 domestic and 50 foreign, mines and deposits in 13 countries. Only 6 domestic properties are considered to be economic reserves, as 29 domestic deposits were found to have an average total cost of production that was uneconomical at a breakeven (0 pct) DCFROR. The 50 foreign properties evaluated were selected to represent at least 85 pct of the known demonstrated fluorspar resources located in market economy countries and China. All evaluated foreign operations were found to be economic to marginally economic in January 1984 dollars. World demonstrated ore reserves of 344 million metric tons (mt) containing 123 million mt of CaF2 were evaluated for the 56 operations. Average total costs needed to cover all costs over the life of each operation were determined for all recoverable fluorspar products. Comparisons of mining, beneficiation, and transportation costs per mt of fluorspar concentrate illustrate advantages between countries. Of the three largest producing countries, China, with its high-grade, low-cost operations had the lowest weighted average total cost of production ($38/mt concentrate). Mexico was next at $54/mt concentrate, and South Africa needed an average of $90/mt of concentrate to cover all costs of production for its low grade deposits.

Jan 1, 1985

By Chao Zhang, Wenhao Xia, Jianxin Fu, Ling Yu, Weidong Song, Yang Li

Sanshandao Gold Mine is the only undersea metal mine in China. To deal with the collapse and pumping of stopes and roadways caused by complex ore-rock occurrence conditions, the mine conducts filling and sealing of some areas, and the remaining ore reserves will be mined after treatment. Therefore, it is urgent to evaluate the stability of rock masses, fault fracture zones, and aquicludes during the secondary mining process. In this study, displacement and microseismic methods are employed to monitor rock deformation and fractures. Additionally, FLAC3D was used to simulate the process of secondary mining, reproducing the evolution of stress fields, displacement fields, seepage fields, and plastic zones at different mining stages. The combination of numerical simulation and on-site monitoring verification demonstrates that the deformation of surrounding rock presents a rapid growth at the initial stage of mining, followed by a gradual decrease in the growth rate, and finally tends to stabilize; the fracture zone area at the 151–159 exploration line on the − 320 m level (near the 7# and 8# stopes) exhibits poor stability, and monitoring measures should be strengthened; the deformation value of the aquiclude is less than the deformation value of I protection level in the Code for Design, the impact of secondary mining on the aquiclude is limited; fault and fracture zone deteriorate rock mass stability, and their impact is related to their spatial locations. Hanging wall fault has a more significant impact on the settlement of the aquiclude, while the footwall fracture zone has a greater impact on the development of the plastic zone.

Feb 21, 2024

By Owens S. Roberts

The drive selected for any piece of machinery must adequately satisfy the application requirements both during the starting interval and at running conditions, All loading possibilities of the drive must be known and allowances made for any adverse limiting conditions such as extreme cold, or perhaps an intermittent excessive loading situation etc. In general, the drive must be selected to provide the required operating characteristics with maximum reliability and at minimum cost. Simplicity of overall design is always an advantage and care must be exercised to insure that systems incorporating unnecessary complicated parts are not indiscriminantly provided. Important non-technical considerations such as equipment avail-ability (on an overseas project) as well as standardization details also play a role in the drive selection process. Additionally, an assessment of the potential capabilities of the personnel that will have to maintain the equipment can have some influence on the final choice. Several types of prime movers are available but this article will restrict itself to the use of induction motors operating from an available alternating current power source. Many drive arrangements are possible, the most common being the direct coupled single motor arrangement. It is sometimes desirable to use more than one motor per machine, but these designs are usually more

Jan 1, 1971

By Stanley Noss

One need be neither an historian nor technologist to recognize that activi¬ties related to the conversion of coal to other usable energy forms have been active for nearly fifty years. The degree of such activity and its evolution to significant commercial proportions has, however, fluctuated widely with world circumstance. For the past decade there has existed both a consistent technology evolution effort in classic R & D proportions, and a mainstream commercial acti¬vity but in rather modest proportions when viewed from the vantage point of world energy needs. But the chain of events wherein it became increasingly obvious that we were in energy trouble irrespective of world politics, spurred alternative energy source activities in the fossil fuels areas. The oil embargo of 1973-1974 made the obvious even more so and provided additional emphasis for the need of such alternatives. Yet the preponderance of these added expenditures and activities (with one notable exception which is the subject of this discussion) has been focused on the intended identification of the best or ultimate process by means of analytical and modest empirical means, whereas our circumstance dictates a bold, higher-risk effort to prove the viability of coal conversion as an industry on a real-time, real-size, real-economics basis. With such proof on hand, industry demands in all related areas will provide the stimulus, motivation and environment for all processes. There is both need and room for many who will compete for a meaningful segment of this new industry which can grow at a rate never seen before in our growth history. The single program in the world today oriented specifically toward the goal of proof of industry viability is the Energy Research and Development Administration's CBF (clean boiler fuels) Program for which COALCON is proud to be the prime contractor.

Jan 1, 1976

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By Lon Santis, Gregory M. Rumbaugh, Christopher Mark

This paper examines the relevant theory, experience, and past practices relating to development mining near gas or oil wells. It addresses setback distance for both coal and stone room-and-pillar mining. This study also involved a review of accident reports involving well interceptions and downhole well surveys. It provides technical considerations for decisions regarding safe setback distances for development mining throughout the United States. The study’s scope is limited to mining near active or inactive (i.e., non-producing, abandoned or inadequately plugged) wells with known surface locations.

Jun 25, 2024

By S. S. Klima, J. A. Organiscak

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed laboratory testing to examine and improve airborne dust capture and methane removal performance of flooded-bed scrubbers on continuous mining machines using a blowing face ventilation configuration to reduce respirable dust exposure to shuttle car operators. Several testing conditions were examined to minimize shuttle car operator dust exposure without adversely affecting continuous miner performance and production. Curtain-to-face setback distance of 9.1 m versus 15.2 m (30 ft versus 50 ft), face ventilation airflow of 226.5 m3/min versus 339.8 m3/min (8,000 ft3/min versus 12,000 ft3/min), and the use of side-body-mounted blocking sprays (on versus off) were the three primary parameters compared. Scrubber airflow was set and maintained at 198.2 m3/min (7,000 ft3/min) throughout testing. An examination of slab cuts versus box cuts and the location of the shuttle car (present behind the continuous miner versus not present in the entry) was also performed to demonstrate the effects of these constantly changing scenarios on scrubber performance. Results show that the best blowing face ventilation setup for minimizing shuttle car operator dust exposure for the tested parameters uses a 15.2-m (50-ft) curtain-to-face setback with 339.8 m3/min (12,000 ft3/min) face ventilation while operating the side-body-mounted blocking sprays. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in U.S. underground coal mining operations, potentially leading to coal workers’ pneumoconiosis (black lung). The U.S. Mine Safety and Health Administration (MSHA) requires that respirable dust exposure to coal mine workers does not exceed a 1.5 mg/m3 average over the actual working shift (79 Fed. Reg. 24814 (2014)). Although using a blowing face ventilation configuration on continuous miner (CM) sections is beneficial for removing methane emissions from the mining face, it can be detrimental for dust control for shuttle car (or ram car) operators and any other workers on the return ventilation side of the CM when compared to exhausting ventilation. Even with machine-mounted scrubbers on CMs, shuttle car operators still have some of the higher dust exposures with blowing face ventilation systems (NIOSH 2011, Beck et al. 2015). Although scrubber discharge air is not completely clean, dust being blown around the scrubber inlet and therefore not being captured by the scrubber can further increase these dust exposures (Goodman 2000). Dust control problems are also caused by inadequate face ventilation quantities causing scrubber face airflow recirculation issues (Schultz et al. 2010). In order to minimize respirable dust exposures on blowing face ventilation sections, ventilation, water spray, and scrubber parameters were experimentally examined to improve operating ranges for both dust and gas control. Several blowing face ventilation factors were examined with respect to CM spray systems and scrubber operation. Curtain-to-face setback distance and side-body-mounted blocking sprays were previously examined in the laboratory for dust control on a full-scale CM model using a scrubber on a blowing face ventilation system (Goodman 2000). The blocking sprays produced larger dust reductions at the CM’s rear corners and return for a 6.1-m (20-ft) curtain setback distance as compared to a 12.2-m (40-ft) curtain setback distance with equal face and scrubber airflows of 169.9 m3/min (6,000 ft3/min). Because face ventilation airflow quantities, shuttle car operator locations, and tracer gas concentration gradients were not previously examined during these experiments, additional research was required to determine improved operating parameters for blowing face ventilation systems.

Jan 1, 2019