Search Documents

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By S. S. Pathak, S. Mishra, M. H. Tyeb, A. K. Majumder

Roping in hydrocyclones is a well-known phenomenon in mining and mineral industries which put serious restrictions on their continuous and maintenance free operation. Roping is mostly observed in association with high underflow solid concentrations which can be attributed to higher fraction of solids reporting to the underflow or the feed solid concentration itself being higher. This paper proposes a newly designed spigot with a truncated conical geometry which can allow for a rope-free discharge at higher feed solid concentrations. The experimental observations revealed that in the operation of a 50.8-mm-diameter hydrocyclone, roping ensued at 10% to 12.5% (wt%) feed solid concentration depending on feed inlet pressure for the cylindrical spigot, whereas with the modified spigot, rope free discharge was attained even at 25% (wt%) feed solid concentration.

Jan 8, 2022

By Paul Wellman

The energy problem of the U. S; was emphasized by the oil embargo of late 1973 and early 1974 and it seemed for a time that the Federal Government, under pressure from the general public, might take some corrective action. However, this was not the case. With the gasoline lines gone and an apparent plentiful supply of petroleum products, public concern quickly dissipated., This country is more vulnerable to an oil embargo today than we were in 1973-1974 and this fact should be of concern to all our people. Since 1968, we have used oil and natural gas at a much more rapid rate than we have been able to find new domestic sources; thus, there is an increasing gap between domestic production and consumption and we have filled the gap with ever increasing oil' imports. These imports have increased at an alarming rate in the recent past, some 58 percent in 1976 compared with 1975. Imports are nearing 8 million barrels per day. Then, by applying some simple arithmetic, at $12 per barrel, the resulting trade deficit is $96 million per day or $35 billion per year. Obviously, this cannot be tolerated by our economy over a long period of time. Historically, we have shifted from one fuel to another as is shown in this slide. In 1850 about 90 percent of our fuel requirements came from direct combustion of wood, by 1900 we shifted to coal for 70 percent of our fuel, and now about 78 percent of fuel requirements comes from oil and natural gas. The difference is that the previous shifts were voluntary and the one facing us now is of necessity.

Jan 1, 1977

By Ramon B. Santos

The Atlas Concentrator, reputedly the largest in the Far East today, is located on the island of Cebu in the Republic of the Philippines. It started operation on a 4000 TPD capacity in 1955. An expansion program, coupled with significant improvements both in the Crushing Plant and the Mil, made the Atlas Concentrator what it is today, treating about 14,000 tons of ore per day at a comparatively low cost of about $0.50 per ton treated. The Atlas Copper Mine is at present mainly an open pit operation, with ore supplied from two pits (Lutopan and Biga) north of the Concen¬trator. Development of an Underground Mine, situated on the main ore body at Lutopan, which will be a block caving operation, has been underway since 1963, and this underground mining operation is expected to b e in full production by the latter part of 1966.

Jan 1, 1966

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

By Jack R. Miller

This session has been organized to suggest to you that the development of direct reduction is important to the iron ore mining and coal mining industries. The papers presented this morning will include a discussion of the costs of making direct reduced iron (DRI), the iron ore and coal supplies needed to produce DRI, the financing of direct reduction (DR) projects and, probably most important, the impact of the DR development on the iron ore and coal industries. For starters, this opening presentation offers a brief statement about DR practice and DRI, under the title that should surprise no one: "Direct Reduction: What Is It?" There is always the chance? that a brief statement may become long and complicated. But, by mixing some slides borrowed from Hal Lownie with a larger number of photographs accumulated from other sources, I hope to avoid such pitfalls.

Jan 1, 1978

By Jorge Ferrero, Andreas Raedle, Uhland Konrad, Michael Dutton, Keivan Pak Iman, Walter Trisi

Strabag, in partnership with Arup, is constructing the Advance Tunnel for the Scarborough Subway Extension (ATSSE); a project by Metrolinx and Infrastructure Ontario (Sponsors). The 10.7 m internal diameter single bore tunnel represents a significant departure from the traditional arrangement of twin subway tunnels in North America. ATSSE is the first-time steel fibers are used to solely reinforce a tunnel of this size in Eastern Canada. This paper discusses the challenges with design and acceptance of SFRC segments and the state-of-the-art numerical models employed to check the joint performance. The advance procurement approach for TBM and PCTL’s procurement to accelerate the project schedule is also presented.

Jun 13, 2023

By T. Takamori

This paper reviews the present status of coal preparation in Japan concentrating on the process in coal cleaning and waste water treatment. This paper also discusses recent topics on maintenance, automatic control, raw coal management, etc.

Jan 1, 1982

By G. A. Irdi

An automated method of microscopy for determining the pyrite size distribution on two base coals that were crushed to 28 mesh x 0 has been developed. Polished epoxy-bound coal pellets were prepared and examined by a Zeiss IBAS image analyzer utilizing a program developed from provided software. Pyrite size distribution determination is considered a necessary first step in pyrite characterization that could lead to successful predictions, by microscopy, of a coal's theoretical pyritic sulfur removal. Our research efforts to date have indicated that the IBP-S can be a reliable instrument for determining pyrite size distribution in crushed coal. A program was also developed to convert pyrite size data to a weight basis for comparisons to the results from chemical analyses. The problems encountered in our research and their solutions will be presented in the discussion.

Jan 1, 1986

By I. Iwasaki

The effects of percent solids, mill loading and grinding time on product size distribution and ball wear were studied in a laboratory ball mill for a taconite ore. Mild steel balls and HCLA steel balls were used to examine the role that ball hardness play in grinding. Net production of minus 325 mesh - material reached maximum at 70% solids, whereas the ball wear decreased as pulp density increased. HCLA steel balls ground the taconite ore finer than mild steel balls under otherwise identical conditions. Examination of ball surfaces with a scanning electron microscope suggested that grinding with mild steel balls involved nipping rather than attrition, whereas grinding with harder HCLA balls involved both nipping and attrition.

Jan 1, 1984

By Ted H. Eyde

Both private industry and the Interior Department have become alarmed about the enormous amount of Federal land that has been withdrawn from appropriation either under the Mineral Leasing Laws or the Mining Law of 1872. According to a recent article by Gary Benethum and L. Courtland Lee, governmental actions have withdrawn nearly 400 million acres from the operation of the Mining Law of 1872 and over 500 million acres from the Leasing Laws. An addition al 100 million acres for the Mining Law of 1872 and 70 million acres for the Leasing Laws are either encumbered or being managed in such a way as to constitute a defacto withdrawal from mineral development. This means simply that mineral exploration end development under the Mining Law of 1872 is either prevented or discouraged in an area the size of the states of California, Arizona, Washington, Oregon, Nevada, Utah, Idaho, and one half of Colorado combined. Under the Mineral Leasing Laws, exploration and development is either prevented or discouraged in an area equal in size to all the states east the Mississippi River, except Maine.

Jan 1, 1976

By W. V. Swarzenski

In its, effort to combat waterlogging and coil salinity, the later and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling and water sampling, since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline ground-water-zones in the Punjab Plain. Fresh ground water containing generally, less than 500 ppm (parts per million) of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh ground water extends to depths of 1,500 feet and more. Saline ground water occurs downgradient from sources of recharge, particularly in the lower central parts of the interfluvial areas and, presumably, underlies most of the Punjab Plain. The ground waters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters, near sources of recharge, to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in Dera Ismail Khan District sodium sulfate waters predominate. The pattern of distribution of saline ground-water zones and the observed gradual increase in mineral content, downgradient from sources of recharge, can be explained best by a hypothesis stressing the processes of evaporation from the water table and solution of minerals within the alluvial aquifer.

Jan 1, 1967

By M. S. Tsai

Recovery of uranium from wet-process phosphoric acid is a newly developed source of uranium. Many processes have been developed but the OPAP (octylphenyl acid phosphate) process is still the valuable one because the OPAP reagent compound has the high extraction ,power and cheap cost. The OPAP process was already studied by murthy(1) in 1970 and its complete process flow sheet was first fulfilled by F.T. Hurst(2) in 1974. WCFC(3) (western Co-op Fertilizer Ltd.) in cooperation with ESI (Earth Science Inc.) set up the OPAP uranium recovery pilot plant in Canada in 1978. We have studied the OPAP process since 1974 and first improved the OPAP extractant by proper adjustment of the DOPAP/MOPAP mole ratio with CH3OH-H20 method, resulting in shortening the phase separation time and avoiding the precipitation occurrence in our process. Second, we utilize the reduction and oxidation occurring by DC power supply on either side of the membrane to achieve the extraction and stripping at the same time. An improved OPAP process in which high recovery yield of uranium and acid uncontaminated by iron has been developed in our laboratory.

Jan 1, 1982

By R. P. Schneider

The Chino mine, concentrator, and smelter are located in Grant County in Southwestern New Mexico. Chino Mines Company is a partnership two-thirds owned and operated by Kennecott Santa Fe Corp., and one-third owned by MC Minerals Corp. (Mitsubishi) of Japan. The Chino Ore Body The Chino ore body is a widely varied deposit of rock types and contains intrusive stocks and sediments. The stocks contain chalcocite in a matrix of quartz, mica, and feldspar. Much of the feldspar is altered to clay. Some of these stocks are enriched with native copper. The sediments contain chalcopyrite associated with gangue minerals including magnetite, pyrite, garnet chlorite, and epidote. The contact of the stock and sediment is heavily altered to chlorite and clay. The stock ores contain economic quantities of molybdenite. The operating work index of Chino ore varies from 5 to 20 kwh/ton and averages 8.5 kwh/ton. The ore head to the concentrator averaged 0.81% copper and 0.010% molybdenum. Fifteen percent of the total copper head exists as nonsulfide mineralization.

Jan 1, 1985

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

By C. C. Jobes

Operating large face equipment, such as continuous mining machines, is one of the most basic and most dangerous elements of an underground coal mining operation. The operator usually performs cutting and tramming tasks in a restricted workspace with reduced visibility. During the execution of these tasks, operators often cannot see all of the locations needed to safely operate the continuous mining machine (CM ), which has sometimes resulted in accidents. In an effort to prevent these accidents, researchers at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, examined the continuous mining machine operator?s current information cues, or visual attention locations, so that risk of injury relative to the task, equipment and workplace environment can be evaluated in the future. The eventual goal is to develop interventions to enhance the information cues, and thereby increase the safety and health of machine operators. This paper details the operator interview process, determination of visual attention locations (VALs) and simulation of various mining scenarios.

Jan 1, 2011

By Lawrence L. Davis

This paper describes current research by the Bureau of Mines to develop technology for improving efficiency and productivity in metal/ nonmetal mines. The research program addresses a wide variety of problems associated with each of the major categories of mining: underground mining, surface mining, in situ mining, and premining investigations. An overview of the Bureau's research activities is given with emphasis on underground mining. In particular, two innovative and promising concepts currently under development are described: a unique shaft sinking system that uses an impact hammer for rock fragmentation, and a low-profile, portable crusher for underground hard-rock applications.

Jan 1, 1979

By M. K. McMullen

Mineral Development Agreements (MDA?s) are a cooperative mechanism in Canada by which the federal and individual provincial governments can coordinate their scientific, techno- logical and market development resources in order to implement measures designed to stimulate mineral exploration and development by the private sector; the objective, ultimately, being to increase the mineral industry?s contribution to provincial economies. In the latest round of MDA?s, which was initiated in 1984, a significant number of planned activities relate to industrial minerals. This paper will describe the nature and importance of MDA's in Canada and will outline the wide range of activities taking place with respect to industrial minerals.

Jan 1, 1987

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

By Ashis Bhattacherjee, Bijay Mihir Kunar

A literature review on quantitative analysis of mine safety studies revealed that investigators use a wide range of statistical techniques for the analysis of mine injury data. Researchers have addressed the various issues of accident causation and prevention through analysis of mine injury data collected from mines. These studies are generally based on historical accident/injury data without considering the injured person/population at risk. In this paper, a public health approach, based on scientific methods of epidemiology, is presented to address mine safety issues. Epidemiology is the scientific study of disease and injury patterns among populations in time and space. Originally, epidemiology was concerned with epidemics of communicable diseases. Then it was extended to non-communicable diseases. Safety researchers found that epidemiologic methods are the best tools for injury research, because the occurrences of injury and the occurrences of disease are quite similar. As a result, some researchers started applying this concept to injury research. This paper presents some of the techniques used in epidemiologic studies and illustrates the application of a case-control study design to evaluate the role of some risk factors associated with injuries in underground coal mines. In this study, the injured persons were identified and, simultaneously, interviews were conducted to find the significant risk factors responsible for occupational injuries in coal mines.

Jan 1, 2011