Search Documents

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, C. Jimenez-Velasco

"Most of the gold produced worldwide is still obtained by cyanidation, in spite of the difficulties encountered in the processing of some gold ores such as the dissolution of copper-bearing minerals in cyanide solutions. The leached copper forms complexes with cyanide and causes several operating problems, which have led to the development of copper removal/recovery processes, among them the industrially accepted SART process (sulfidization, acidification, recycling and thickening). Although the SART process is in use in gold production plants around the world, new challenges are appearing with the continuous varying of the mineralogy of ores (such as higher copper grades, changing the solution composition and complexity). The optimal SART operating conditions for a specific solution are not the same when the composition of the solution changes; consequently, the efficiency of this process can decrease.The present study is a thermodynamic approach, corroborated by laboratory experiments, to explain how the main variables of the process affect the efficiency of copper precipitation as cuprous sulfide (Cu2S). The variables considered were pH value, copper concentration, cyanide/copper molar ratio and sulfur/copper molar ratio, all of which werevaried within the limits encountered in typical cyanidation solutions presenting the problem of copper.It was found that the variable that most affects the efficiency of the process was the pH value, since poor or no control of it can cause cuprous sulfide redissolution. The S/Cu molar ratio is also important: raising this ratio increases copper removal, but high ratios will also cause sulfide and cyanide losses. The effect of changing the CN/Cu molar ratio was negligible between 4 and 8. For a solution containing 300 mg/L copper and 490 mg/L cyanide, copper removal as high as 98.8% can be obtained with the addition of 0.6 moles of sulfide per mole of copper at pH = 6.IntroductionThe main process for gold production is cyanidation, because it is the most economical and efficient process so far. Precious-metal leaching occurs when the ore is placed in contact with a dilute alkaline cyanide solution. The dissociation of cyanide salts provides free cyanide ions, which allow the formation of the aurocyanide complex Au(CN)2 -. This complex can be retrieved from the solution by adsorption on activated carbon or by zinc precipitation. Although the use of cyanide represents an issue to health and the environment, there are technologies for its management and treatment that can be easily applied. Furthermore, it is a low-cost process compared with other methods that are available or under development."

Jan 1, 2015

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022

By J. L. Ellenberger, G. S. Esterhuizen, T. Miller, M. M. Murphy

A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor convergence monitors were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.

Jan 1, 2015

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By R. W. Wittkopp

The Relief Canyon gold deposit is located approximately twenty- four kilometers east of the town of Lovelock in Northwestern Nevada. At Relief Canyon, the Late Triassic Grass Valley Formation has been thrust over the Late Triassic Natchez Pass Formation. The lower plate Natchez Pass Formation is composed of massive gray dolomitic limestone which is locally silty and sandy. The upper plate Grass Valley Formation is composed of shale, siltstone, argillite and quartzite. Gold mineralization at Relief Canyon occurs along the highly brecciated thrust contact between these two formations. Weak gold mineralization often occurs above the thrust in the Grass Valley Formation, however, most of the ore grade mineralization is present below the thrust in the brecciated Natchez Pass Formation or where the two formations are mixed as a result of movement along the thrust. Several types of gold mineralization have been recognized at Relief Canyon. A large amount of the ore is present as a jasperoid breccia, however, significant amounts of ore occur as a mixed breccia composed of upper plate rock, fresh limestone, clay and jasperoid breccia. Gold ore also occurs in a fresh limestone breccia which contains a large amount of clay. Below masses of jasperoid, jasperoid stringers containing gold extend into the fresh limestone. Gold mineralization at Relief Canyon appears to be truly disseminated and has the typically associated trace elements of arsenic, antimony, mercury and fluorine. The Relief Canyon deposit can be classified as a structurally controlled disseminated gold deposit. Other deposits that fit this classification are the Pinson and Dee gold mines.

Jan 1, 1984

By L. Zhou, L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly; however, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics, namely size and location, are of great importance in reducing the risk of mine fire injuries. A new improved fire location algorithm has been developed and integrated into an Atmospheric Monitoring System (AMS) program by researchers from the National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

Sep 29, 2020

By J. Rostami, J. Brune, S. Slouka

Respirable dust poses long-term health issues to personnel working in mining and civil projects where mechanized mining and tunneling machines are used for hard rock excavation. Machines, such as longwall shearers, roadheaders, or continuous miners, use consumable picks to cut rock. However, rock dust is generated in the work environment each time the pick tip contacts the rock surface. Additionally, the generated dust can be reintroduced into the air further down in production, such as at transfer points. The purpose of this study is to characterize respirable dust particles generated at the pick tip at two stages of pick wear: new and moderately worn. Understanding dust characteristics in terms of concentration, size distribution, and particle shape throughout the life-cycle of the pick will provide a basis to mine and tunnel operators for changing out picks to mitigate dust generation at the source. This paper discusses the dust characteristics generated from preliminary full-scale cutting tests in a laboratory of an igneous rock block cut with conical picks at new and moderately worn levels of wear. The moderately worn pick generated a size distribution that favored smaller particle sizes compared to the new pick. The moderately worn pick also generated more overall dust, as the concentration level in mg/m3 was over double the amount of the new pick. Lastly, both picks generated particles that had similar aspect ratios and roundness measures.

May 18, 2022

By A. Newman, M. Goycoolea

"In this paper, we consider an underground production scheduling problem consisting of determining the proper time interval or intervals in which to complete each mining activity so as to maximize a mine’s discounted value while adhering to precedence, activity durations, and production and processing limits. We present two different integer programming formulations for modeling this optimization problem. Both formulations possess a resource-constrained project scheduling problem structure. The first formulation uses a fine time discretization and is better suited for tactical mine scheduling applications. The second formulation, which uses a coarser time discretization, is better suited for strategic scheduling applications. We illustrate the strengths and weaknesses of each formulation with examples.IntroductionProject scheduling is an important aspect of underground mine planning that consists of determining the start dates for a given set of activities so as to maximize the value of a project while adhering to operational and re-source-availability constraints. Important activities that require scheduling include development, drilling, stoping and other ore-extraction techniques, and backfilling. Precedence relation-ships impose an order in which activities can be carried out based on their location in the mine: for example, the activity a associated with development of an area must be completed before the activity a´ associated with extraction of that same area can begin. Re-sources include attributes of the mining operation, such as the amount of extraction and mill capacity available per time period, and are determined by capital and equipment availability and other factors. In this paper, for our set-ting, resource-availability constraints consider the amounts of material that can be extracted and sent to the mill — that is, processed — per time period."

Mar 1, 2017

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By Bob Snashall

"We could blow that damned fort out of existence if we could run a mine shaft under it!," claimed one Union soldier eyeing Bobby Lee's Petersburg defense line protecting Richmond and Jeff Davis. Puncture the line, take the hill behind, and the Confederate capital would celebrate Yankee jubilee, 1864. That was June. At 4:15 am, July 30, mine boss Henry Reese, sergeant, 48th Regiment, Pennsylvania Volunteers, gingerly entered the mine, dark and muddy. Something had gone wrong. The mine, set to go off at 3:30, hadn't exploded. It had to be checked. The main mine gallery, 1.5 m high x 1.4 m wide (5 x 4 ft) narrowing at the top to 0.6 m (2 ft), forced Reese into a tuck run. Some¬where up there in that 155 m (511 ft) stretch running 6 m (20 ft) under the rebel works, moisture may have doused the charge. Or maybe a fuse splice went awry. Or maybe there was live fire steaming like a locomo¬tive towards 3.6 t (4 st) of black powder. Perhaps now Reese wished this sprint was shorter. For the mine boasted a record break¬ing distance in military annals. Lieut. Col. Henry Pleasants Credit goes to Lieut. Col. Henry Pleas¬ants, commander of the 48th, who overheard the soldier's claim for what a mine could do. In peacetime, Pleasants had been a railroad engineer working on the Sand Patch Tunnel. He later switched to mining, working for the Philadelphia & Reading Coal & Iron Co. He even married the daughter of the editor of The Miners Journal. Grieving over his wife's early death, Pleasants plunged into the ven¬ture of war. This Union officer took the mine idea to the brass. Headquarters was less than enthu¬siastic. "The chief engineer of the Army and the rest of the regular Army wiseacres said it was not feasible," Pleasants wrote to his uncle. The pros scoffed, ticking off a list of horribles: No mine has ever gone that far, men will suffocate and be crushed, the rebs will countermine, the men will be trapped. Still, Pleasants eked out a signal to proceed. In the meantime, the miners of the 48th had commenced to dig anyway. It was like the 48th to proceed against the odds. The 48th Pennsylvania Volunteers The 48th had been recruited from Penn¬sylvania's Schuylkill County, anthracite coal mining country. The mines had been torn with strife over wages. Strikes and rioting were prevalent. Murder was not unknown. This "Buckshot" resistance centered in Pottsville, PA. It forced the governor to call in troops. Coal was in high demand to run the war machine. Pennsylvania operators worried that a military draft would stir up violence, closing the mines altogether and further shift¬ing business to emerging Illinois mines. Men lit out for the western gold fields in the tens of thousands. Secret societies bred in the mining camps invited draft agents to dance at the end of a rope. Jobs threatened by cheap, victorious South¬ern labor were one warning intended to get immigrant miners interested in the war. Operators gave miners time off to help de¬fend Philadelphia during Lee's thrust to Gettysburg. Even so, the draft spawned new violence and troop intercession. Soldiers were not welcome. The dust had barely settled when into this Pennsylvania "minefield" marched the 48th on a recruitment drive. The 48th had been in Lexington, KY on guard duty. When it came time for the regiment to pull out, the townspeople had prevailed upon authorities to extend the regiment's stay. Finally ordered to move out, the 48th was feted by a hanky-waving, tear-dropping send-off to the lyrical lament Auld Lang Syne. And Kentucky fancied itself to be rebel. Striding smartly into the Pennsylvania coalfields, the 48th attracted 400 recruits and marched off under regimental colors specially made by the proud citizens of none other than Pottsville, PA.

Jan 1, 1989

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

By J. C. Motz

With ore grades continually decreasing and finer mill feed requirements, it becomes increasingly important to have the capability to handle the larger tonnages economically. With the 10 ft. Standard capable of reducing 1,633 metric tons per hour (1,800 short tons per hour) to 80 percent passing 50 MM (2 inches) and the 10 ft. Short Head following to produce a mill feed of all minus 12 MM (1/2 inch) at a rate of 608 metric tons per hour (670 short tons per hour), we feel significant savings will be realized in installation and operating costs. The largest concentration of cost in the secondary and tertiary crushing stations is the building itself that houses the process equipment. An example of the savings to be attained can be seen from an examination of a 40,820 metric ton (45,000 short ton) per day crushing plant. A total of nine 7 ft. Symons Cone crushers is used to generate 12 MM (1/2 inch) ball mill feed. The average center distance between units is 6.1 M (20 feet) and allowing a 6.1 M (20 feet) nominal distance from the centerline to the wails, the building becomes 61 M (200 feet) long. For this production rate, four 10 ft. Symons Cone crushers would be required. With the 10 ft. crushing plant requiring a center distance spacing of 7.6 M (25 feet), the building length totals approximately 38 M (125 feet). Construction costs vary depending on location, but a reduction in building length from 61 M (200 feet) to 38 M (125 feet) will result in estimated savings of between $2,500,000 and S4,000,000. While the 10 ft. Symons Cone has been involved in a number of feasibility studies for some time, the Process Machinery Division of Rexnord commenced detail design work on the 10 ft. Cone crusher in 1972. For comparison purposes, the 10 ft. and 7 ft. capacities are given in Table 1.

Jan 1, 1978

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By Gary N. Weinrich

Large surface mining projects in sparsely populated regions of the West have the potential to create disruptions in an area's social and economic character with potential effects on man that can far outweigh the physical and ecological effects on man's environment. The data and analyses involved in addressing the socioeconomic issues are additional to those traditionally associated with surface coal mining, such as those concerning land reclamation and water quality. Appropriate socioeconomic studies in conjunction with mine-planning can identify the potential problem areas in order that project measures can be taken to maximize the beneficial impacts and minimize the adverse effects of surface coal mining. The information required to conduct such socioeconomic analyses, available data sources, and the applicable analyses are described. Overall impacts of some proposed Western surface mines are summarized and potential mitigating steps discussed.

Jan 1, 1975

By P. F. R. Altounyan, I. W. Farmer

Groundwater freezing was used to stabilise 8m thick beds of saturated and weakly cemented sands at a depth of 170m, during driving of twin 1 in 4,5.2m o.d. circular drifts from the surface to the Coal Measures through 600m of Permo-Triassic strata. Instrumentation was installed during erection of the lining in frozen and unfrozen ground to measure ground and groundwater pressures on the lining and ground temperatures up to lm into the frozen ground. Observations showed that following thawing, effective lining stresses in the frozen zone were low, indicating minimum strata disturbance during freezing and subsequent machine excavation. Groundwater pressures were lower than expected.

Jan 1, 1981

By W. C. Dailey

The Groveland Mine. Concentrator and Pellet Plant are located in Dickinson County in the Upper Peninsula of Michigan. The construction of the Groveland Mine in 1959 was the first United States operation for the Hanna Mining Company in mining and beneficiating low grade iron formations. (1) The plant produced concentrates at 675,000 lt/yr. (746,600 mt/yr.) which was used as sinter feed in the steel industry from 1959 to 1963. Upon completion of a pelletizing plant in April, 1963 production increased to 1.6 million lt/yr (1.77 million mt/yr) of pellets. After the plant expansion, mill capacity increased to 2.2 million 1t/yr (2.43 million mt/yr.), producing 2.0 million It/yr (2.23. million mt/yr.) of pellets assaying 63.0% iron and 7.0% silica. (1) Prior to April, 1971 the concentrator operated with a flowsheet consisting of spirals and a petroleum sultonate iron notation circuit. This was presented in a paper by R. R. Smith and E. E. Sougstad, "Flotation at the Groveland Mine" in the 50th Anniversary Volume entitled "Froth Flotation". The ore body at the Groveland Mine consists basically of two types of iron formation (34% total iron, 20% magnetic iron head), the most abundant of which is a bedded magnetite-chert-silicate rock. This is intermingled to varying degrees with non-bedded to poorly bedded hematite-clastic quartz-chert rock. (1) In developing the Groveland flowsheet, Humphrey spirals were used because of their ability to produce a coarse size concentrate at a low cost. Tests run in the lab and pilot plant on the Groveland ore showed a. spiral weight recovery in the 27 to 33% range. (2) However as the ore body was opened up, it became evident that the most abundant ore type did not liberate at the coarse size fraction needed for spirals. Plant recoveries for the first five years operating the spirals only averaged from 10 to 15% weight recovery. In 1971 the weight recovery on the spirals had dropped to a low of 5%. To increase iron recovery and at the same time increase plant capacity with the least effect on the present operations the mill flaw-sheet proceeded from a spiral-notation circuit to an all flotation circuit to a magnetic separator-flotation circuit. During this changeover the concentrate grade also had to be improved to meet market demands. To do this the following changes evolved

Jan 1, 1978

By A. C. Bigley

Before going into this subject, I would very much like to call to your attention some past history on patents granted by the United States Patent office that involved ammonium nitrate. On February 10, 1885, a patent was granted to Russell S. Penniman. "The object of this invention is to securely protect ammonium nitrate against deliquescent and to maintain it in substantially its normal disintegrated condition, so as to afford a new product suited for ready use in the manufacture of high explosives, and enable the immediate admixture thereof with any of the well known explosive substances or compounds heretofore employed. 'Whether the nitrate be thus granulated or otherwise reduced to a granular or divided condition, it is then thoroughly mixed with about twelve (12) percent of the fluid or semi-fluid carbonaceous protecting medium, which forms a readily applied jacket or coating for the granules of nitrate and also serves as a carbonaceous element in such explosive compounds as it may thereafter be employed in."

Jan 1, 1958

Semiautogenous (SAG) ball mills are being increasingly used today for the coarse grinding of a range of ores, including gold, copper and iron. Larger mines are demanding mills with larger throughputs. This has led to some remarkable developments in mill diameters and installed powers. Conventional design principles - mills with trunnion bearings - have reached their limitations. This article describes one SAG mill with a slide-shoe arrangement and Krupp Polysius' Combiflex twin drive. In August 1997, the world's largest SAG mill with a slide-shoe arrangement was commissioned in Queensland, Australia, operating as a wet mill. The inside diameter is 10.4 x 5.1 m (34 x 17 ft) effective grinding length. The 1.36-ktlh (1,500-stph) SAG mill is driven by two Combiflex drives (twin drives with 2 x 5,500-MW or 7,375-hp installed motor power) in conjunction with a girth gear (outside diameter 11,890 mm or 468 in.). Commissioning of the SAG mill was completed with no notable technical difficulties. The plant runs continuously except for planned maintenance stoppages and process-specific reasons. As this article is written, the machine has been in operation for about 8,000 hours without major problems.

Jan 1, 1998

By D. C. Seidel

The role of surface charge in soluble salt flotation, which was developed in Part 1, is extended to relate the theory to the specific phenomena of KCI- NaCl separations. Temperature-collector solubility relationships, metal ion activation, and particle size effects are discussed.

Jan 1, 1967