Search Documents

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By C. F. Lee, Bezalel C. Haimson

A 300 m deep test hole at Ontario Hydro's Darlington nuclear plant site, 65 km east of Toronto, was used to determine the state of stress in the Paleozoic limestones (O-22O m depth) and the Precambrian granitic gneiss (220-300 m). The results of the hydrofracturing measurements indicated a state of high horizontal stress along the depth of boring and a consistent orientation of principal stresses in each geologic unit. These results were confirmed by a borehole TV camera survey, and by overcoring tests. The magnitudes and orientations of the measured in situ stresses were used in a feasibility study of siting an underground nuclear plant, and in particular in the geotechnical design of proposed reactor caverns in Precambrian rocks. Their implications on cavern stability under operational and accident conditions were analytically studied, taking into consideration the potential superposition of thermomechanical stresses under loss-of-coolant condition, and the possibility of thermal spalling in the host rock.

Jan 1, 1979

By QUANWEN PU, Yonggang Wei, Bo Li

The spent catalyst is one of solid waste resources, which contains precious metals with considerable recovery value. However, due to the different compositions of catalyst, the recovery process is difficult. Most of the catalysts are supported by alumina which has good alkali-soluble properties, while platinum is insoluble in alkali. Platinum is enriched by pressurized alkaline solution which is a kind of hydrometallurgical process. The novelty of this study is the separation of alumina and platinum from the spent catalyst and the enrichment of platinum in the solid phase. In this study, a leaching process using NaOH as leaching agent under high temperature and pressure was employed. The effects of alkali concentration, leaching temperature, leaching time, and liquid–solid ratio on leaching efficiency were investigated. The optimum process conditions were determined as follows: alkali concentration of 240 g/L, temperature of 200℃, pressure of 1.20 MPa, time of 1 h, liquid–solid ratio of 5:1. It was concluded that the leaching rate of alumina can reach 99.69%. The content of platinum increased from 0.1749 to 21.12%, the loss of platinum was 3.39%, and the enrichment ratio of platinum increased by 120.82 times. The leaching kinetics of alumina was studied based on the shrinkage core model. The activation energy of alumina leaching is 19.53 kJ/mol, and the leaching process is controlled by chemical reaction. Pressurized alkali solution can not only efficiently leachate alumina from the spent catalyst and enrich platinum, but also reduce the reaction time and increase reaction rate.

Feb 11, 2022

By L. Yan, B. Lambie, J. Srednicki, J. Carr

Electromagnetic emissions from electrical devices may interfere with electronic safety systems or other devices in the mining environment. This electromagnetic interference (EMI) may cause unwanted changes in the performance of the affected devices and may cause safety issues for miners. To minimize the risk of EMI, the National Institute for Occupational Safety and Health (NIOSH) has conducted research quantifying the electromagnetic emissions of several types of equipment that might be used in the mining environment. Previous research has shown that welding arcs can give off ultraviolet (UV) emissions, visible light, and infrared (IR) emissions that can cause health problem on skin and eyes. In this study, the electromagnetic emissions of the shielded metal arc welding (SMAW) process were monitored and measured. Several factors including operating mode (AC, DC positive or DC+, DC negative or DC-), current setting (low, medium, high, maximum), and electrode type were investigated to compare their effect on emission level. The test shows that the emission level from the welding process can be affected by those factors. The test data also shows that, among those factors, the operating mode has more influence on emission level than do current setting and electrode type. The information in this paper can be useful for the mining industry to better understand the emission in the 9-kHz to 500-MHz frequency range from a SMAW welder.

Feb 1, 2023

By P. J. Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man's house as it was mined. Then it may have been stockpiled at each man's place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

By W. Gibson Jaworek

Of increasing importance to the student of fuels economics has been the extent to which different primary energy sources can substitute for each other in the various energy markets of the nation. Knowledge of the nature and extent of fuel interchangeability can aid the fuels economist in projecting trends of energy utilization, as well as giving him a better understanding of the past and present conditions of fuel markets. It is also important to the consumer to know just how much flexibility he can maintain in his energy consuming operations. And, finally, various governmental bodies show keen interest in the degree of energy substitutability in determining public policies concerning the fuels industries. The presence of excess fuel production capacity in the United States during the early 1960's indicates that fuel interchangeability should become more prevalent in the increasingly competitive energy markets of the nation. Discussion of fuel intercompetition is almost always restricted to qualitative terms-because of the lack of comparable statistical data, between the different energy sources in geographic or "type-of-use" fuel, markets. There are exceptions, of course, such as, the excellent fuel consumption data which are available on steam electric generating plants throughout the nation. In other sectors, statistics are at best incomplete.' Inmost instances, indirect fuel consumption indicators, such as sales of fuel burning equipment, are extensively used to measure market shares of a particular fuel; however, these indicators are hard to evaluate precisely without prior knowledge of the total competitive market.

Jan 1, 1961

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By Vivek Priyadarshi, VIVEK KUMAR HIMANSHU, A. K. Vishwakarma, M. P. Roy, A. K. Mishra, RAVI SHANKAR

The nature and orientation of joints in rock strata affect the damage pattern under explosive loading. Most of the limestone deposits in India are found with severity of joints. Categorically, these joints may have variable orientations such as dipping out of the blast face, inside the face, horizontally or having strike parallel to the face. The damage pattern under the varying category of orientation will be different. Accordingly, a numerical model in Ansys-Explicit Dynamics was prepared to compare the damages of rock mass under different joint orientations. The physical nature of a joint reflects frictional and stiffness behaviour. Accordingly, the damages have been compared under bonded and frictional nature of joints. The output damage pattern from the model has been validated on the basis of blastability index proposed by Lilly. Different limestone mines in India show different nature of jointing in their rock strata. Accordingly, the blasting outputs from three different limestone mines, viz. Rawan limestone mine, Sagmania and Birhauli limestone mine and Injepalli limestone mine, have been compared along with their blast design parameters and the nature of joint. The comparative results show that the closely spaced horizontal joints support maximum in burden movement and rock fragmentation due to blast.

Nov 23, 2023

By Xinming Chen, Huazhe Jiao, Qi Zhang, Yunfei Wang, Liuhua Yang

The effect of initial damage generated by weakly cemented interlayer surfaces on the physico-mechanical properties of layered cemented tailings backfill (LCTB) is considered for the interlayer inclination structure generated by multiple layered backfills in large-scale mining voids. Utilizing the theory of damage mechanics, the damage evolution and constitutive model of LCTB with interlayer inclination is constructed by considering the coupling of interlayer inclination effect and loading. Based on Mitchell’s mechanical model, we analyze the damage mechanism of the inclined cementation surface of LCTB, and derive the expression for the strength of LCTB considering interlayer inclination. The mechanical properties test of LCTB with different inclinations was carried out, and the results showed that the damage model of LCTB established was highly consistent with the experimental curves, which verified the correctness of the model. The initial inclination damage leads to the decrease of adhesive cohesion of cemented surface, and with the increase of inclination, the separation of layered surface, aggravation of misalignment, layered cemented surface is more prone to shear damage, and the mechanical properties of cemented tailings backfill in the lower part of layered surface are not effectively played, which reduces the overall performance of the material.

Nov 23, 2023

By Sunfangze Liu, Xumeng Chen, Yongjun Peng

Efficient separation of naturally hydrophobic gangue, such as talc and carbonaceous materials, from sulphide minerals in flotation is becoming a significant challenge in many processing plants due to the need to process lower grade and more complex ores. Considering the hydrophobic nature of these gangue minerals, prefloating them at the beginning of the flotation circuit in the absence of collectors and rejecting the concentrate is a common practice to remove these gangue minerals. However, sulphide minerals, such as chalcopyrite, can become naturally floatable due to surface oxidation and therefore may float together with naturally hydrophobic gangue. In this study, a new approach was developed to maximize the prefloat of hydrophobic gangue while minimizing the loss of sulphide minerals. The new approach introduced a prefloat cleaner stage where sulphide minerals recovered to the prefloat concentrate was depressed and separated from other hydrophobic gangue minerals at a low pulp potential with the prefloat cleaner tailing fed back to the main sulphide flotation circuit. Flotation tests were conducted using chalcopyrite and organic carbon. The results show that the proposed approach can significantly reduce the loss of valuable minerals in the prefloat flotation without affecting the reject of naturally hydrophobic gangue. Applying pulp potential control at the prefloat cleaner flotation stage also reduces the consumption of reducing agents while minimizing the effect of reducing agents on downstream rougher flotation.

Nov 23, 2020

By Alvaro Lucio

The continuous increase of the fuel oil price compelled CV3D to look for an alternative fuel. Charcoal was selected as the alternative energy source. This paper justifies its selection, describes charcoal properties, the methods for using charcoal in the pelletizing and shows the results of the in-plant tests.

Jan 1, 1982

By John Newby, Ulf Gwildis, Ken Massé, Guillaume Roux

How to connect an effluent conveyance tunnel to riser shaft and diffuser arms of an outfall system is dictated by the ground conditions, which ideally include rock or soil strata of low permeability. Where such favorable conditions are beyond reach, both the complexity of designing and the risk of constructing this crucial system connection increase disproportionally. This paper describes the considerations that went into the approach of connecting a 5-m-diameter TBM drive with the in-river riser shaft of the Annacis Island WWTP New Outfall System in the highly permeable Fraser River sands at hydrostatic pressures exceeding 3 bar.

Jun 23, 2024

By Don L. Deardorff

The Deserado Mine and transportation system is the fuel supply portion of the Bonanza Power Plant project. Deserado Mine con¬sists of an underground mine with a capacity of 1,224,700 tonnes (1,350,000 tons) of clean coal per year, a 649 tonne (715 tons) per hour closed water circuit jig type preparation plant, a 5.6-kilometer (3 ½ -mile) overland conveyor with covered slot storage, a unit train rail load-out and 59.5 kilometers (37 miles) of totally independ¬ent, captive electrified railroad. Planning and exploration started in March of 1978. Construction of all facilities was completed in April of 1984, approximately six years after initial planning was commenced. This paper will discuss exploration, environmental permitting, mine planning, engineering and construction of the Deserado Mine project.

Jan 1, 1984

By A. M. Anthony, A. Y. Atta, S. S. Magaji, U. Abubakar-Zaria

There are two major gold recovery methods: the hydrometallurgical technique, which employs cyanide solutions, and amalgamation method, which involves mercury (Hg). These methods present considerable health, safety, and environmental concerns. Past applications of alpha-cyclodextrin (α-CD) on gold scraps show that α-CD is not only inexpensive, but is also environmentally friendly. This research work used α-CD to recover gold from gold ores instead of gold scraps. The gold ore was sourced from Shanono gold deposit site Kano State,Nigeria. The gold ore was characterized by fire assay (FA) for the precious metal. The concentrate was digested with aqua regia (AR) for 24 h. Modified AR, where hydrochloric acid was replaced with hydrobromic acid, was used for the gold digestion due to the good match in molecular recognition between gold bromide ion (AuBr)− and α- CD in a second sphere coordination complex. The digestate was characterized using atomic absorption spectroscopy (AAS). Gold recovery using this technique is pH sensitive, and five pH values (2.0, 3.6, 4.0, 5.4, and 6.0) were investigated. FA analysis showed the Shanono gold ore deposit contains an average of 4.71 ppm of gold, AAS analysis showed highest gold recovery of 69% at pH 4.0, which is lower than recoveries from the metal scraps. This could be due to the presence of other gangue minerals closely associated with the ore. However, gold recovery using α-CD on Shanono gold ore has shown to have a higher yield of 69% compared to 35.5% yield obtainable by Artisan Small Scale Miners using mercury.

May 5, 2020

By Steven P. Oman

Large room and pillar mines are characterized by numerous and widespread working places. Ventilation requirements are high since each panel employs men and equipment that work simultaneously in multiple headings. Also, it usually is not feasible to redirect airflow from idle to active panels as the demands of each shift vary so every panel in the mine is fully ventilated at all times. Ventilation requirements will be even higher for mines that are classified as gassy. As a result of these considerations, ventilation systems for room and pillar mines are generally designed to handle large quantities of air. But as mining progresses and the mine be- comes larger, greater demands will be placed on the ventilation system. To insure that adequate ventilation is maintained at these times, ventilation engineers must anticipate problems and plan how best to deal with them.

Jan 1, 1983

By Peter G. Chamberlain

Domestic mining will not produce a significant portion of the manganese consumed in the United States unless new mining and processing techniques are implemented that will enable domestic lean ores to economically compete with rich foreign ores. One mining-processing technique that appears promising for certain deposits is in situ and/or heap leaching with aqueous SO2. Since leaching offers economic advantages of low capital costs, low operating costs, and short start-up times as well as environmental and safety improvements over conventional mining-processing, the Bureau of Mines studied the leachability of manganese deposits from several districts. Manganese oxides, hydroxides, and carbonates were leached to 80 to 90 pct recovery in 7 to 40 days of leaching with a solution containing 5 pct SO2 in column leaching tests. Preliminary cost analyses of surface mining-heap leaching, block caving-in situ leaching, and shrinkage stoping-in situ leaching indicate that the products of manganese leaching may be economically produced for the chemical and electrolytic manganese industries. The easiest marketable product to obtain would be a manganese sulfate commonly used as a fertilizer amendment. Manganese carbonates and hydroxides could also be precipitated from the pregnant leach solutions.

Jan 1, 1983

Software exhibitors at MINExpo will feature the newest, the best, the most comprehensive computer-based tools available to get minerals from the ground to the market. From the ?cloud? to the pit, the variety that will be featured is almost limitless ? a digital tool for every phase of the mining lifecycle. Blue Sky Network SkyRouter brings the Blue Sky Network to the cloud. Using its interactive Web portal, SkyRouter, with detailed mapping and integration with Google Earth, the Blue Sky Network links enterprises to personnel and assets anywhere on earth through Iridium satellites. The cloud-based solution is designed to support connectivity with remotely dispersed mobile assets, including Blue Sky?s dual-mode GSM and Iridium tracking and communications services. This enables seamless connectivity with assets in problematic cellular reception areas, where only 10 percent of the Earth is covered, and in remote locations.

Jan 1, 2012

By J. G. Dunn, A. S. Ibrado, D. J. Hollbach

Gold production is one the most important mineral process­ing industries in Western Australia. The gold is usually found in either weathered oxidised zones, or associated with sulfides. In the latter case, oxidation is achieved by some form of chemical processing, such as roasting or more recently bacterial leaching. In all cases, gold is dissolved out of the oxidised matrix by cyanide solution. Pyrrhotite is an iron sulfide generally represented by the formula Fe1_,S where O x 0.125. Three different structural forms ofpyrrhotite are known to occur naturally, stoichiometric FeS (troilite), hexagonal pyrrhotite Fe1_xS and monoclinic pyrrhotite Fe7S8 [I]. Substitution of iron atoms within the pyrrhotite structure by other ions of similar atomic radius such as nickel, copper, cobalt and manganese is also possible [2], and often observed in natural pyrrhotite samples. Pyrrhotite is abundant in Western Australian sulfide mineral deposits which are commonly associated with gold bearing ores. It is generally believed that pyrrhotite has a detrimental effect on gold recovery from such ores, as it is commonly claimed to decompose in alkaline, aerated cyanide solutions to form iron cyanide complexes, thus consuming free cyanide, and to form sulfur/oxygen containing species such as sulfate, through oxidation of sulfur in pyrrhotite, which thus consumes oxygen. From information gleaned from the literature, claims about the high reactivity of pyrrhotite in cyanide appear to be based on early cyanidation studies performed on gold ore samples which have been poorly characterised, and contained impurities such as pyrite, arsenopyrite and chalcopyrite, which may have also contributed to the levels of species observed in solution [3-5]. In addition, the investigations do not take into account that iron atoms in the pyrrhotite structure may have been partially substituted by other atoms that influence the solubility of pyrrhotite in cyanide solution.

Jan 1, 1995