Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By W. K. Choi

Using electrochemical techniques it was demonstrated that bioleaching of gold from refractory pyritic ores is a complex phenomenon. Many intermediate electrochemical reactions were found to be involved in the oxidation of pyrite, using cyclic voltammetry and carbon paste-pyrite containing electrode. Furthermore, the oxidation process was controlled by solid-state diffusion as suggested by chronoamperometric and chronopotentiometric measurements. Using the Sand's approach, the activation energy of solid-state diffusion was found to be = 22.4 kJ. After bioleaching, 96% gold was extracted from the leach resi¬due with a thiourea solution in 1 hour. A generalized model for the mechanism of pyrite oxidation has been presented.

Jan 1, 1990

By William S. Alldredge

The Washington Metropolitan Area Transit Authority(WMATA) officially came into existence in February 1967 after the District of Columbia, Maryland, and Virginia joined in a com¬pact pursuant to Federal creative legislation signed the previous November to build a regional rapid rail transit system called METRO (1). The parent organization was the National Capital Transportation Agency (NCTA), a Federal agency, subject to Federal statutes and regulations. Soon after the completion of the transition from NCTA to the new "non-Federal" status of the Authority, the Board of Directors of the Authority formally adopted procurement policies and procedures (2). These are specific statements concerning competition by formal advertising for bids or by solicitation of proposals for negotiation, contracting authority, approval of awards, awards of contract modifications, and processing of claims and disputes. These policies and procedures are silent as to Federal procurement statutes and regulations. But because of the Authority's origin, the sensitive nature of the compact among the several sovereign jurisdictions, Federal financing of two-thirds of the costs, and the resultant surveillance by the General Accounting Office over staff operations, the Authority's procurement practices follow closely Federal regulations adapted to WMATA's needs. This is an important point and is the foundation of contractual relations between the Authority as the owner and its construction contractors. Various constraints and flexibilities of this arrangement with respect to excavation and tunneling contracts will be pointed out in the ensuing discussions.

Jan 1, 1974

By Jameel Menashi

Aqueous solutions of Na2Cr04 can be reduced with CO to produce hydrous Cr203 and NaHCO3/Na2CO3. CH3OH, HCOO and HCHO in the presence of CO2 also reduce Cr 6+ and yield similar products. It is shown that the rate of Cr6+ reduction can be represented by the expression -d[Cr6+]/dt=k[Cr6+)1/2[R] where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mole. Rapid reduction rates are attained at temperatures in excess of 220°C and, with these three reductants, a green acid-insoluble readily filterable hydrous Cr203 is formed. With HCHO significant reduction of Cr6+ occurs at about 80-100°C and an acid-soluble violet modification of hydrous Cr2O3 is formed. The reduction process is reasonably selective: solutions of Na2CrO4 contaminated with Mo6+ and W6+ can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels. These findings are utilized as a basis for a process for recovering chromium from secondary source materials.

Jan 1, 1984

By Nasser Madani, SULTAN ABULKHAIR

The abstract of the paper discusses the challenge of quantifying iron content in a coal deposit in Kazakhstan. The iron dataset is limited, coming from only three drill holes and some stope samples, while a large amount of geological information is available from legacy drill hole data. The paper proposes a workflow using multiple-point geostatistics to model geological domains and two-point geostatistics to model iron content within these domains. The results show that the direct sampling (DeeSse) algorithm effectively reproduces the complex seam layers, and sequential Gaussian simulation models the iron within each domain.

Mar 30, 2022

By H. M. King

A combination of chemical, statistical, geographic, and microscopic analyses reveal that sulfur in West Virginia coals is extremely variable in both form and abundance. Coals in southern West Virginia typically contain less than 1% total sulfur with organic sulfur being the dominant species. Northern West Virginia coals average about 2% total sulfur, mainly contributed by sulfur minerals. In addition to these regional trends, significant variations in sulfur form and abundance exist both vertically and laterally within individual seams. On both regional and local scales, the pyritic sulfur component can vary significantly in mineralogy, particle shape, maceral association, and particle size.

Jan 1, 1986

By Sunny Murmu, Gnananandh Budi

One of the most significant concerns in longwall ground control is the instability and failure mechanism of the coal wall. The current research uses FLAC3D to simulate panel 1 of the Adriyala Longwall Project, India, in order to evaluate the distribution of vertical stress and material failure mode, in and around the longwall face. Additionally, three distinct criteria are used to evaluate coal wall spalling: vertical stress distribution, maximum shear strain, and residual cohesion. A novel algorithm is also proposed to appropriately capture roof bed caving, shield installation and advancement, and coal extraction from the face. The findings of the modelling show that progressive longwall extraction creates an elliptical stress relief zone around the excavation void. During the peak stress phase, the height of the stress relief zone is greatest, whereas the width is highest during the main fall phase. As mining advances, the coal wall at the face line appears to lose its stress-bearing capability. Shear failure was the most common coal wall failure mode. Maximum spalling depth (MSD) and longwall face spalling index (LFSpI) were used to measure the extent and volume of coal wall spalling in FLAC3D. For panel 1 of the ALP mine, the MSD, and LFSpI were determined to be 3 m and 90.5 %, respectively. The mode of coal wall spalling was expected to be total or fragmented failure. The field observations and the numerical modelling findings were in good agreement. The compressive strength and deformation modulus of the immediate roof appear to have a substantial role in coal wall spalling. The results of the proposed numerical simulation exercise can help strata control engineers better detect the risks of coal wall spalling and enhance face control for safe and productive working environment at the longwall face.

Aug 8, 2023

By J. W. Motter

Currently, virtually all new electric power generation systems under construction are designed with natural gas as the primary fuel. Factors driving these construction decisions involve sustained low prices for natural gas, environ-mental (and consequent regulatory) risks associated with the use of coal for power generation, and relatively high costs of construction for conventional coal-fired power plants. Despite the unarguable abundance of coal in the US. and worldwide, a fundamental question arises: What will be the role of coal in electric power generation in the 21st century? Congress, recognizing the vital and strategic importance of preserving the coal option for electric power generation, authorized the Clean Coal Technology Program. This pro-gram, with original funding in excess of $2,500 million, is intended to promote the demonstration and commercialization of a new generation of clean, efficient coal-based energy technologies through collaboration and partnering with private industry. The two technologies being demonstrated under this program which are the key to the continued use of this nation's huge coal reserves are coal gasification and the pressurized fluid bed. Either or both of these technologies, coupled with a combined cycle will pro-vide the continuing future coal option, while responding to increasingly more restrictive environmental standards. Recent Congressional budget-cutting efforts, however, could threaten the effectiveness of that model program, and ultimately other subsequent government-industry collaboration.

Jan 1, 1996

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By Jan Wolf

The iron ore industry presently utilizes two types of de-posits. The first are the high grade deposits generally located in remote areas and, secondly, the low grade de-posits which are normally found nearer to the steel-making centers. The high grade deposits produce a direct shipping ore which has an iron content which may be close to the maxi-mum 70% of Fe. These deposits have reserves which are ex-pressed in billions of tons. The ore needs little or no up-grading and where this is performed is restricted to ore washing. With the large demand for iron ore pellets, plus a national drive to perform as much of the upgrading as possible in the native country, there is a trend to erecting pellet plants at the mine location~ Large iron ore suppliers such as Australia, Brazil, Venezuela and Liberia already have pellet plants in operation, and there are new plants projected or expansion projects under study. The low grade ores are mined at locations closer to steel mills such as in Minnesota, Michigan and Canada. These low grade ores require methods of beneficiation to obtain a commercially accept-able product with the modern beneficiation techniques it is no~, possible to produce iron ore pellets of 68% Fe and 4.5% silica from ores containing as low as 26% Fe. Figure 1 gives a general picture of the types of iron ores and their beneficiation. The final product of the high grade ore is a coarse concentrate, sinter product or pellets. The final product of the low grade ores is pellets and, in some cases, coarse concentrates.

Jan 1, 1971

By John A. Meech

In many multiple-sulphide ore flotation processes, it is desirable to concentrate each of the various valuable minerals into separate products. Although there are a variety of techniques and chemicals which can be employed to produce efficient separation, two basic types of flotation circuits are used: The Differential Flotation Circuit and the Bulk/Selective Flotation Circuit. Figure I depicts these two circuits in their most simplified form for the production of two concentrates and one tailing product. If three or more valuable minerals are present in an ore, a variety of combinations or extensions of these two basic flowsheets may be used. There are many examples of the successful application of both circuit types with ores containing similar minerals. Each ore must be tested individually to decide on which circuit is best. However, the following general statements can be made: 1) The differential circuit will have higher capital and operating costs than will the bulk/selective circuit due to higher rougher capacity requirement. 2) The differential circuit will achieve better separation than will the bulk/selective circuit since it is usually easier to reactivate a depressed mineral than it is to depress an already active mineral. If the deactivation problem with the bulk/selective circuit . . in can be overcome, there is a clear economic argument for its use

Jan 1, 1977

By A. K. Andersen

One of the prime examples of the versatility of the MARCONAFLO system, which is a body of technology comprising the means to handle, store, load, transport, discharge and reclaim mineral commodities in slurry form, is the direct application of this process to leaching ores. The initial approach was to provide a much improved materials handling system for the transport of copper ores; however, an extensive development program, inclusive of prototype and pilot plant tests, has established that a new leaching concept is possible with this system. Data are presented from the leaching operation of a 25 TPD pilot plant utilizing a copper-oxide ore, mainly chrysocolla. This pilot plant was designed to incorporate true countercurrent flow where the ore is actually in motion, as contrary to vat leaching operations, and the ore being successfully leached is fine crushed ore (3/8-inch x o), contrary to agitation leach circuits. Extractions in excess of 85% of the soluble values are common with only 15 hours of retention time in the MARCONAFLO leaching system.

Jan 1, 1975

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The use of phosphorus by mankind is long established. From use in agriculture, foods, high tech electronics, and more recently in EV battery cathode production, one cannot escape its impact on today’s society. This paper will review and describe the circular journey of phosphorus through its value chain from the mining operation of phosphate ore through beneficiation into downstream chemicals production and finally into the EV battery cathode production space. This will include a review of phosphoric acid production from phosphate concentrate using wet process route and thermal route. The wet process route discussed will be via dissolution of phosphate concentrate by sulphuric acid. The thermal route will discuss thermal decomposition of phosphate concentrate using submerged arc furnace to produce yellow phosphorus followed by its combustion to produce phosphorus pentoxide and subsequent hydration to produce phosphoric acid. It will also discuss briefly other phosphate derivatives for specialty chemicals and recovery of phosphorus units from wastewater treatment plants, sewage sludge and incinerator ash. Finally, the paper will discuss the use of phosphorus in EV batteries in the form LFP cathode materials and its production. It will also briefly discuss the LFP battery recycle.

Sep 11, 2023

By S. Mohanta, S. Chakraborty, B. C. Meikap

"An air dense medium fluidized bed separator is an efficient dry process for the removal of undesirable gangue material from run-of-mine coal. Its cleaning performance depends on a variety of operating parameters that are interrelated in unknown, complex ways. A literature review showed that these parameters' effects had been experimentally investigated using a traditional one-variable-at-a-time approach, which is highly inefficient and sometimes misleading because many of the parameters often interact with each other to alter the overall equipment performance. Also, it is realized that the interrelationship among these parameters can have a significant effect on equipment performance. Therefore, to correctly evaluate the effects of individual parameters as well as their interactional effects on the separation performance of an air dense medium fluidized bed, we conducted a scientific study based on response surface methodology. Empirical models for two key response variables, namely, product ash and combustible recovery, were developed and subsequently used for identifying an appropriate operating region to achieve optimum separation performance. Furthermore, the optimum performances predicted from the empirical models were validated against experimental data. Preliminary results show a strong interaction among the operating parameters investigated in this test program.IntroductionFluidization is widely applied in industry for its various useful features. In the coal industry, it is used in the air dense medium fluidized bed (ADMFB) separator for the beneficiation of run-of-mine coal. In this separator, a medium is created by suspending fine magnetite particles in an upward air flow, and this pseudo-fluid is used as the beneficiation medium, with the lighter coal particles floating to the medium’s surface while heavier particles sink to the bottom. This separation technique had been receiving a significant amount of attention worldwide in recent times for its specific advantages of low operating cost and less restriction for small capacities (Luo and Chen, 2001; Sahu et al., 2009; Dwari and Hanumantha Rao, 2007; Van Houwelingen and de Jong, 2004), but it is still not a well-established industrial practice because of the availability of efficient wet processing technology. However, with a revival of interest in the dry beneficiation of coal, in general, and ADMFB, in particular, there is once again a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have been made to make this process a competitive and viable option. The existing literature reveals that most of these research efforts had been essentially focused on the identification of a single parameter that has a key influence on separation performance, without taking notice of parameter interactional effect. For example, Luo et al. (2004) proposed a pressure drop number to distinguish separation performance without considering the bed height and gas velocity, which are intimately related to this proposed pressure drop number."

Jan 1, 2015

By D.G. Osborne

Each month abstracts of the papers selected for the Annual Bound TRANSACTIONS Volume will appear on this page. Since the Annual Bound Volume will not be published until the spring of next year, this will give people an opportunity to order copies of the papers earlier. If you would like copies, fill out the coupon below and return it to SME-AIME. Each copy will cost

Jan 1, 1985

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

By Dewa Putu Agus Sudarmaja, Widi Astuti, Januarti Jaya Eka Putri, Yayat Iman Supriyatna, Himawan Tri Bayu Murti Petrus, I Wayan Warmada, Siti Nurul Aisyiyah Jenie, Ferian Anggara, Anisa Maulidia, Vincent Sutresno Hadi Sujoto, Sutijan

With the rapid development of renewable energy technology, such as electricity reserves, to store energy for electric or electric vehicles, environmentally friendly energy sources are expected to continue to be fulfilled according to mobility and stationary energy needs. Lithium is the most attractive candidate for energy storage development. The presence of lithium in Indonesia in the Sidoarjo mud content is interesting to be used as an alternative source of raw materials. During the research, sulfuric acid acted as a solvent, and hydrogen peroxide acted as an oxidation agent. Lithium recovery will be studied using a leaching process at various temperatures (30, 45, and 60 °C) and sulfuric acid concentrations (0.5, 1, 2, 3, 4, and 6 mol/L). The increasing temperature, sulfuric acid concentration, and hydrogen peroxide concentration will directly affect the lithium recovery. An increase in sulfuric acid concentration will be directly proportional to the recovery of lithium in the solution. Optimum conditions were obtained at varying 6 mol/L sulfuric acid concentrations and 60 °C temperature variations. The shrinking core model (SCM) studied leaching kinetics, and ash layer diffusion acted as a rate-controlling process. The activation energy of the leaching process was obtained at 38.90 kJ/mol.

Jul 25, 2023

By Z. Jin, D. DePaoli, P. Zhang

"Phosphorite, or phosphate rock, is the most significant secondary rare-earth resource. It contains high amounts of phosphate-bearing minerals along with low contents of rare earth elements (REEs). In Florida, about 19 Mt of phosphate rock are mined annually and most are used to manufacture fertilizers using a wet process, in which sulfuric acid reacts with phosphates to produce phosphoric acid and phosphogypsum. In the wet process, REEs are also leached out into solution and eventually get lost in the leaching residue and phosphate fertilizer. Recovering REEs from Florida phosphate rock in the wet process will be beneficial to broadening rare-earth availability, improving the quality of phosphoric acid product and protecting the environment.This study focuses on the influences of wet-process operating conditions on REE leaching efficiency. The results indicate that REE leaching efficiency increases with phosphoric acid addition in the initial pulp. At a temperature of 75 °C, a stoichiometric ratio of sulfuric acid (H2 SO4 ) to calcium oxide (CaO) of 1.05 and a weight ratio of liquid to solid of 3.5, REE leaching efficiency reached a relatively high value of 52.82 percent. The trends of REE leaching efficiency were similar to those for phosphoric acid (P2O5 ). Extensive tests on the leaching residue showed that during leaching, about 90 percent of the REEs were released from the phosphate rock but only 52.82 percent ended up in the leaching solution. This phenomenon can be attributed to two factors: (1) the effect of phosphate ions (PO4 3-) in the solution, which caused REE ions to form REE phosphates and be precipitated into the leaching residue, and (2) the influence of large amounts of anions such as sulfate (SO4 2-), dihydrogen phosphate (H2 PO4 -) and hydrogen phosphate (HPO4 2-) anions as well as the polar molecule H3 PO4 , which surrounded the REE cations and formed an ion atmosphere that prevented the PO4 3- from contacting and combining with REE cations. Interaction of these two opposite effects determined the REE distribution between leaching solution and residue."

Jan 1, 2017

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2018

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2017