Search Documents

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

By Eung Ha Cho, Wendi Li

Wet desulfurization of Pittsburgh No. 8 coal and Illinois No. 6 coal were conducted with sodium hypochlorite in the laboratory. Pittsburgh No. 8 coal was leached by hypochlorite at high pHs in one step only. The hypochlorite concentration varied from 0.2 to 0.6 molar; sodium hydroxide concentration, from 0.2 to 0.8 molar; and temperature was at the levels of 80 and 90°C. The desulfurization of Illinois No. 6 coal was conducted in three consecutive steps of pretreatment in concentrated ammonia at room temperature, leaching with hypochlorite at room temperature and hydrolysis in sodium hydroxide solution at 90°C. In the leaching step, hypochlorite concentration varied from 0.2 to 0.8 molar. The desulfurization method of Pittsburgh No. 8 coal was found to reduce mainly pyritic sulfur. More than 70% of pyritic sulfur removal was achieved at the optimum conditions of 0.4 molar hypochlorite, 0.4 molar sodium hydroxide and 90°C. The desulfurization method for Illinois No. 6 coal was capable of reducing significant amounts of organic sulfur. The removal of organic sulfur achieved a 37.8% reduction at the optimum operation of leaching at 0.4 molar hypochlorite and room temperature followed by hydrolysis at 0.3 molar sodium hydroxide and 90°C. The chlorine content in the coal produced by the chlorination during leaching was kept below the threshold value of 0.3% at the optimum conditions of the desulfurization method for each coal.

Jan 1, 2005

By H. Sevim, M. K. Mohanty, Y. P. Chugh

The economics of “Conventional” and “Advanced Fine Coal Cleaning” (AFCC) circuits for refuse pond reclamation as well as active mine/preparation plant applications have been evaluated. The benefits of innovative tailings management schemes on the profitability of mining enterprises have also been evaluated as a part of this study. Analyses have been conducted for scenarios involving generation of two different product qualities of 5.81%, a quality that was obtained during AFCC circuit operation at SIU, and a more typical 8% product ash. The inability of the conventional circuits to achieve profitability while producing the lower ash content product is revealed from this approach. The spiral-only circuit is unable to produce a 5.81% ash product. A different version of the same circuit involving spirals and column flotation produced the desired product quality but could not maintain profitability. The AFCC circuits on the other hand, achieve net present values greater than $6 million, with return on investment in excess of 50%, in the water-only as well as dense medium mode, with and without tailings management. Addition of tailings management system to any of the circuits is found to enhance the project economics. The comparison of water-only and dense-medium applications of the AFCC circuits indicate a better suitability of the dense-medium circuit for producing premium quality products. Application of AFCC circuits in active mines offer better economics compared to applications in refuse pond recovery operations. The superior project economics are a result of reduced overhead cost and use of existing material handling facilities. Sensitivity analysis reveals the significance of capacity utilization on project economics.

Jan 1, 2002

By Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, José Gomes-Pereira, Inês Tojeira, Andreia Afonso, António Calado, Luísa Pinto Ribeiro

Since 2008, the Portuguese Task Group for the Extension of the Continental Shelf has been operating the ROV "Luso" (rated for 6000m depth) for geological sampling of the deep North Atlantic seabed, performing surveys on, e.g., seamounts and hydrothermal vent fields. Amongst other sensors, the ROV is equipped with a full HD video camera with which still images of the deep ocean floor are recorded. Fixed on the ROV’s frame are two underwater "line" lasers, each generating a sharp green line (532nm) over the seabed. The two lasers are paralleled and calibrated at a set distance. Provided that the camera’s angle of view is known, numerical values for seabed surface area may be calculated using direct measurements taken from the pictures containing the laser lines. We present the corresponding main mathematical formulas, which are derived from simple geometrical considerations, and discuss how to generalize these results for an arbitrary camera tilt or pan. We present an example of application of our method by estimating values for percent coverage of rock substrate versus sediment. Our results are also relevant for determining seabed polymetallic nodule abundances from still images obtained during ROV surveys.

Sep 1, 2014

By R. Hardy

LaModel is a boundary-element program capable of calculating the displacements and stresses in thin bedded deposits such as coal, salt, or potash. Throughout its history, it has continually been upgraded in order to expand analysis detail and stay current with the latest advances in computer technology. The most recent enhancements include: an increased grid size capability, a significant increase in the speed of the automatic grid generation using an AutoCAD visual interface, implementation of subsidence-based horizontal strain calculations for multiple-seam situations, and pillar safety factor calculations. To demonstrate these new features, a multiple-seam case study of a longwall panel undermining an active set of main entries is presented.

Jan 1, 2006

By Steve Kral

About 500 mineral-processing professionals from around the world gathered in San Francisco, CA in Oct. 22-27, 1995 for the XIX International Mineral Processing Congress (IMPC). Following the theme “Leading Mineral Processing into the 21st Century Through Advanced Technology,”186 speakers from 28 countries covered research and development activities and innovative processes. Subjects included comminution and simulation control, physical and chemical processing, flotation practices and fundamentals, precious metals processing and mineral waste and the environment.

Jan 1, 1996

By V. T. McLemore

Petrographic analysis of rocks is traditionally performed with optical microscopy using thin sections and point counting. However, this does not provide accurate mineral proportions for sedimentary, volcanic, and soil-like material, because rock fragments, groundmass, and matrix are not identified as specific minerals. In addition, groundmass phases in volcanic rocks can be too fine to identify individually, and making thin sections of intact soil-like material is difficult because much of the material is not well cemented. ModAn is a normative calculation that estimates modes ??by applying Gaussian elimination and multiple linear regression techniques to simultaneous mass balance equations? (Paktunc, 2001) and allows location-specific mineral compositions to be used. One of the features of ModAn that makes it appropriate for this study is that it can model one of several sulfide minerals. Mineral compositions for Questa minerals were determined from electron microprobe analysis and entered into ModAn. Then by combining and normalizing results, bulk quantitative mineralogy can be determined using ModAn, petrographic observations, electron microprobe analysis, clay mineral analysis, and the whole-rock chemistry of the sample.

Jan 1, 2009

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By Richard P. Graff

Author?s note: Diversity in practice exists in the application of Generally Accepted Accounting Principles (GAAP) for purchase price allocations with respect to the recognition of Value Beyond Proven and Probable Reserves or VBPP, as defined by the Emerging Issues Task Force (EITF) in EITF 04-3: ?Mining Assets: Impairment and Business Combinations?. This diversity appears to arise from differing interpretations of what constitutes sufficient information to value components of VBPP in business combinations. Concerned with this diversity in practice, respected members of the mining community formed a working group which prepared an issues paper that discussed this diversity and provided recommendations for recognition and valuation of VBPP in business combinations. The working group then submitted this paper to the EITF, requesting further guidance be issued on the concept of VBPP. In conjunction with the submission to the EITF, the working group also provided this paper to the United States Securities and Exchange Commission (SEC) for review and comment. The EITF discussed this issue at its May, 2008 agenda committee meeting. However, it declined to add this topic to the EITF agenda for further consideration. Absent additional guidance on VBPP from the EITF, the working group submitted a proposed definition of VBPP to the U.S. Securities and Exchange Commission for its consideration. The following article, which is consistent with the issues paper that was submitted to the EITF and the SEC, discusses the components of and valuation techniques for VBPP. The correspondence with the U.S. Securities and Exchange Commission, which includes the proposed definition of VBPP by the working group, is attached as Appendix 1 to this article.

Jan 1, 2008

By L. A. Ruth

Vision 21 is a government/industry/academia cost-shared partnership to develop the technology basis for integrated energy plants that will, early in the 21stcentury, result in the deployment of ultra-clean plants that produce electricity and “opportunity” products. Vision 21 plants will use fossil fuel feed-stocks in combination with other domestic resources, e.g., biomass, municipal waste, and petroleum coke. Opportunity products could include transportation fuels, steam, high-value chemicals, synthesis gas, and hydrogen. Performance targets for Vision 21 plants, example plant configurations, and the key technologies that will be needed are described.

Jan 1, 2000

By S. Ragab

The objective of flotation models is to predict the recovery rate of minerals from a flotation cell. In this paper a CFD?based flotation models is presented. The model uses first order rate equation, and the collision frequency is estimated using Abrahamson [1] model with input from CFD two-phase simulations. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) are determined by the two-phase hydrodynamic simulations. Knowing these parameters throughout the machine is essential in understanding the effectiveness of different components (rotor, stator or disperser, jets) on the flotation efficiency. Not only the average pulp recovery rate can be estimated but also the regions of high/low recovery rate can be identified. The CFD-based flotation model presented here can be used to determine the dependence of recovery rate constant at any locality within the pulp on particle diameter, particle specific gravity, contact angle, and surface tension.

Jan 1, 2012

TABLE TUNNEL NAME OWNER LOCATION STATE TUNNEL USE LENGTH (FEET) WIDTH (FEET) BID YEAR STATUS Gateway Tunnel project Amtrak Newark NJ Subway 14,600 24.5 2015 Under study

Sep 1, 2013

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

By William H. Dresher

Introduction A subject long debated but rarely resolved involves the interaction between the academic community and industry in the sponsorship and conduct of research. The subject is, unfortunately, too often treated as a controversy involving ethics and the profit motive. But, in fact, the two branches of society - industry and academia - are necessarily part of the same system. In the last 25 years, the realization has developed that research alone is not sufficient to bring about use of those results to benefit society through productivity gains and economic growth. The flow of events shown in Fig. 1 was generally believed to be the steps required for reaping the benefits of research. Today, research still has the very important role of creating new information or new ideas. However, it is recognized to be but one of many steps in a process that we now refer to as technological innovation. Charpie (1967) said, "Technological innovation is the driving force behind economic growth in the US. In this context, innovation means the process by which a new idea is successfully translated into economic impact within our own society, by providing better products, and simultaneously creating new jobs in the manufacturing of those products. Only after an investigation is put into sufficient use to have an economic effect, is it termed an innovation." One of the best depictions of the technological innovation process is shown in Figs. 2 and 3. These are adapted from Haeffner (1975), and modified by the Committee on Mineral Technology of the National Research Council (1981). Figure 2 identifies the many steps involved in the process. It designates a generalized form for interaction between the academic community and industry. Figure 3 identifies the steps in the "innovation activity" box of Fig. 2. Academia is generally responsible for developing of new knowledge and ideas, as well as maintaining and enlarging the collected body of scientific knowledge. Industry is responsible for developing new products, methods, and processes. Both institutions operate for the benefit of society, but under different driving forces. In academia, the driving force is the achievement of academic excellence. In industry, the driving

Jan 10, 1984

By E. R. Spencer

An assessment of U.S. western hard-rock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed, and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hard-rock mining machines. Ninety-six percent of the operators had daily noise doses that exceeded the Mine Safety and Health Administration?s permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214%, and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jack-leg drill. These results will be used to help prioritize noise control development by NIOSH and other partners. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

To preserve Washington Group International's quality of service in the mine operations area, the company has established a Supervisor Training Program to provide all levels of supervision with the required skills to meet objectives and guarantee consistent, excellent performance for each of our projects. A need developed to establish this training program internationally. The first international training session was held at the APEX San Cristóbal Mine in Bolivia. This paper discusses the program’s development, execution, results, and lessons learned with an emphasis on multicultural environments.

Jan 1, 2007

By Y. P. Chugh

During late 2010, a scientifically founded water spray system was developed for continuous miners (CM) (Patent Pending) that reduces respirable dust exposure for miner operator by about 30%. It includes engineered sprays around the cutting drum, outer bit-ring sprays, chassis sprays and side cutter boom sprays. About 3.6 ? 4.5m (12-15 ft) behind these sprays is additional sprays that spatially cover the area between the CM chassis and the mine roof and ribs. The spray system uses approximately the same volume of water as currently used on CMs with similar operating pressures. An Illinois mine decided to implement these concepts on a CM during rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric sampling and real-time monitoring using multiple personal dust monitors (PDMs). The average results based on about 105 cuts show about 30% and 20% reduction in dust exposure for the miner operator, and the haulage unit operator. Visibility in the mining areas was also significantly improved. The coal company has already decided to implement the system on all their CMs.

Jan 1, 2012

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

By M. E. Kuchta

Research is currently being conducted at the Colorado School of Mines in the use of high-pressure water for scaling down loose rocks in underground mine openings. In addition to improved miner safety, the adhesion strength of shotcrete applied to rock surfaces treated with high-pressure water is also increased significantly resulting in improved overall support capabilities of the shotcrete layer. Test results show an increase in adhesion strength by a factor of four on a concrete test wall cleaned with water at 21 Mpa (3000 psi) as compared to a surface cleaned at 0.7 Mpa (100 psi).

Jan 1, 2002