Search Documents

By A. Habibi

The ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system consists of nine shafts (three intakes and six exhausts). Three surface based axial fans ventilate the mine configured in a blowing arrangement. Following the ventilation survey airflow quantity, frictional pressure losses and air psychrometric characteristics have been quantified. An accurate resistance survey has been conducted to calculate the pressure drop with regard to moving cages and skips in the shafts. This paper discusses the benefits of utilizing high accuracy digital pressure transducers and psychrometers in a ?leapfrogging? survey to gather data needed to build the computer ventilation model. Two underground booster fans with VFD are currently idle but available at the mine. The ventilation model has been used to determine the optimal booster fan locations to decrease the overall operating cost by reducing the load carried by the main fans. A leakage study has been conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next fifteen years of mine operation and investigates the effect of proposed scenarios.

Feb 27, 2013

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By W. Pawlos, A. Bakalarz, M. Duchnowska

This paper presents the results of an investigation into the influence of hydrodynamics on a preflotation process for the copper sulfide ore from the Fore-Sudetic Monocline deposits in Poland in a flotation machine. The main aim of the preflotation stage for Polish copper ore is to remove the easy-to-float organic matter — organic carbon — that causes serious problems in metallurgical processes. The organic matter is connected with the presence of shale ore. This paper describes the preflotation experiments conducted to investigate the effect of various stirrer speeds. The upgrading selectivity of copper and organic carbon were analyzed and compared. The results show that the effectiveness of separation between organic carbon and copper decreases with increased stirrer speed in the laboratory flotation machine. The more intensive the mixing of the flotation suspension, the lower the selectivity of the preflotation experiment. Lower stirrer speed probably provides lower mechanical entrainment and flotation of copper minerals.

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By I. T. Oramah

Despite the abundance of solid mineral deposits, Nigeria only earns about 0.5-1% of its current Gross Domestic Product (GDP) from the solid minerals sector. This is as a result of the dominance of the oil and gas industry, which has negatively affected the competitiveness of other sectors of Nigeria’s economy. The dominance of this industry has resulted in unemployment, poverty, hunger, domestic price inflation, corruption, unstable government, and higher exchange rates. These impacts are typical for economies suffering from the effects of "Dutch Disease" and the "Resource Curse". Community-based small-scale mining offers hope as an economic activity that can create wealth, employment, reduce hunger and poverty, and provide basic amenities for rural communities with solid minerals endowment. This study presents preliminary results of ongoing research into the prospects of using community-based small-scale mining in a developing country like Nigeria to move towards rural sustainable development.

Jan 1, 2011

By R. Fernández, E. Marczak, A. Collins

Newmont roasting plant in Carlin, Nevada commenced operating in December 1994. Over the years, refractory ores and pyrite concentrates from different gold deposits constituted the feed to the facilities. Historical plant performance indicated that the roasting temperature was the main variable that affected the structural characteristics of the calcine which, in turn, affected the recovery of gold by cyanidation. Gold recovery as a function of roaster temperature was closely monitored since October 2000. Original design temperature was 550oC. Lower roaster temperatures of around 500oC resulted in gold recovery increase by more than 6 percent. This increase was directly related to an increase of the surface area of the calcine. The implementation of an “intelligent” process control system helped significantly in achieving steady low roasting temperatures thus achieving high gold recoveries between 92 and 93 percent. Under those conditions, several roasting campaigns with high-arsenic-containing ores were conducted, which resulted in a significant decrease of gold recovery. The reduced gold recovery was caused by the loss of surface area (e.g. porosity) of the calcine as the arsenic content of the roaster feed increased.

Jan 1, 2007

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By U. Richter

Conveyors are a highly effective means of transporting material over long distances. Recently there has been a trend toward long conveyor systems with high capacity single flights. These conveyor systems are an efficient alternative to costly truck fleets. Also with deeper mines, the use of diesel driven trucks becomes more difficult. Another trend is in underground mining, where conveyors are an efficient alternative to drift hoists or dedicated rail systems.

Jan 1, 2012

By Raja V. Ramani

As the new millennium approaches, it is appropriate to assess the progress that has been made in mine health and safety, a matter of concern to management, labor and government. One can hardly look at the major events of the last century — from the birth of the US Bureau of Mines through the enactment of the modern health and safety laws — without realizing that the march has been relentless toward eradication of health and safety threats in mining. The progress is spectacular in mine safety and significant in mine health. In looking at the future, it is safe to assume that societal demands will increase for improved health and safety conditions in the workplace. So will the demands for greater technological leaps. The standards will for measuring success and the expectations of progress in creating a safer and healthier mine environment will grow. The possibilities are enormous of meeting these exacting requirements in the 21st century.

Jan 1, 1999

By Y. Boissonnas

INTRODUCTION, The transalpine rail routes in Switzerland are well over one hundred years old. As the established routes no longer meet the demands of the continually increasing volumes of rail traffic between north and south, two new routes through the Alps were planed. The old Gotthard rail line is in fact a mountain railway. The northern and the southern access ramps?with a maximum speed of 80 km/h and a maximum slope of 2.2%?reach the old Gotthard rail tunnel at an elevation of approximately 1,100 m above sea level. This is approximately 900 m higher than the city of Milan. In 1992, the Swiss electorate people voted with an overwhelming majority in favor of the project to build the new base routes through the Alps. The Swiss voted again in 1998 in favor of the financing proposal for the new infrastructure. Swiss Federal Railways together with the BLS Lötschbergbahn were commissioned for the realization and management of the Gotthard and Lötschberg routes. AlpTransit Gotthard Ltd., founded by Swiss Federal Railways, was given the task of managing the design and realization of the Gotthard route until the start of regular service. In the meantime the shorter Lötschberg Base Tunnel was open to traffic in 2007

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By Dan Armour

Bolting solutions traditionally offered only wet drilling or dry drilling options; each with advantages and disadvantages. Joy Mining Machinery has developed a Mist Drilling System that incorporates the best of both types of drilling. Compared to wet drilling, mist drilling offers as much as a 90% reduction in water use. As a result, floor and roof conditions are tremendously improved. This offers a safer and more comfortable work environment for operators. Mist drilling can offer a significant reduction in noise levels compared to dry drilling and in recent trials, bit life has been greatly improved. Holes are cleaner and operators experience less exposure to respirable dust.

Jan 1, 2005

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By H. -J. Langhoff

"The paper describes not a result, but a starting point to implement sustainable development to a region characterized by a typical down river landscape, agriculture, and extractive industry. The NaturFreizeitNiederrhein GmbH (NFN) is a private company with associates from administrative bodies, the local mining companies and multiple representatives of environmental protection groups (local and national), tourism organizations, cultural societies and also aquatic sport and fishing clubs. Center of the concept is the "NFN Lake District." The development concept aims to provide the agricultural industry with alternative means of income, while protecting wildlife and the ecological balance as well as preserving the social und cultural system and enhance the safety against flooding from the river Rhine. The mining industry contributes their coordination of obligation concerning reclamation and recultivation of the already existing individual projects. While designing the landscape components and establishing the infrastructure for the different tasks, the production of gravel and sand is yield as a by product. The result is a long term perspective for region and industry."

Jan 1, 2005

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By E. Carvajal I

Large diesel engines provide the mining industry the substantial power and torque needed to move large amounts of material efficiently. But the stresses generated by such power and torque necessitate complex maintenance programs to ensure the utmost operating capabilities are not compromised. Of all its available sensors, the Exhaust Temperature differential between the right and left banks can provide the most valuable indicator of the overall operating condition and potential degradation of a large diesel engine. BHP Billiton Escondida Mining has implemented real-time remote monitoring, diagnostics, reporting, and tracking of Exhaust Temperature differential using Modular® technology. As a result of the processes and procedures put into place surrounding their MineCare maintenance management system, Escondida has proactively replaced over 300 injectors, resulting in an increase of 4% in Engine availability.

Jan 1, 2011

Your assessment of the minerals business. The global mining industry is strong. I am convinced it will continue meeting the mineral needs of the world population for the foreseeable future. Two developments have greatly enhanced the industry’s ability to produce low-cost minerals. Technological innovations have resulted in increased productivity. And there has also been a dramatic expansion of the number of favorable countries in which to explore and mine. Capital expenditures have flowed to the low-production-cost mines and development projects as well as to the exploration projects and stable countries having the best potential for valuable mineral discoveries.

Jan 1, 2000

Oil sands processing generates huge volumes of slurry, known as tailings, that is being stored in tailings ponds. The volume of produced tailings is a very important factor in oil sands surface mine planning, because the available area for dam construction is limited to the lease areas. On the other hand, oil sands operators cannot leave mine sites without reclaiming the tailings ponds. Since most of the reclamation material is generated in either oil sands mining or processing, it is reasonable to include reclamation material requirement as part of long-term mine planning. In this paper, an integrated optimization framework is proposed to maximize the net present value (NPV) of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. A sample bitumen processing flow sheet is used to formulate the volume of produced tailings, based on Clark hot water extraction method. To verify the proposed model, it is coded in Matlab and run using CPLEX. Run results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Feb 27, 2013

By J. Stoll

In May 1998, Hanson Aggregates Midwest, as an outcome of mine planning, offered a 10-acre tract of land containing the famed fossil-bearing Silica formation, to the City of Sylvania, OH. in the form of a 99-year lease agreement. The Olander Park System, and Ohio code park operating within Sylvania Township, was then approved by Hanson and the City to manage and fund the park. All parties signed the lease in August of 1999. In November 2001, local residents voted to fund the park by a margin of 2 to 1. The park will consist of a shallow (approx. 20 ft.) former cement production quarry that is 700 ft. long by 300 ft. wide. Hanson’s motivation and vision for the park was fivefold: 1) the site was located away from long-term reserve access; 2) it would serve nicely as buffer property for the active quarry; 3) it had become an area of illegal dumping by locals in the past; 4) trespassing and safety issues would be limited by allowing supervised usage; and 5) the shallow outcropping contains the world famous, fossil-bearing Silica shale. Hanson will supply shale to the park perpetually via stripping activities in the process of uncovering quality construction aggregate limestone and dolomite reserves. Thousands of enthusiastic fossil hunters have already combed throughout the shale in their quest for “treasures”. The park’s master plan also features nature trails, picnic areas, a fossil-themed play area, amphitheater, visitor’s center and gift shop. Given the natural and people resources that Sylvania Fossil Park will have to offer, Hanson is confident that it will become the premier invertebrate fossil hunting site in the United States. It will also remain a solid community relations vehicle for years to come.

Jan 1, 2003

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008