Search Documents

By Betty L. Gibbs

A short course, held during the SME Annual Meeting in Phoenix, AZ in February, focused on software for surface and underground mine modeling. The objectives of the short course were to review techniques for surface and underground mine planning. Mine planning software vendors were invited to demonstrate how their software runs, given a standard data set. Six vendors of mining-specific software participated in the workshop. They were Exploration Computer Services (MINEX 3D), GEMCOM Services, Inc. (PC-MINE), KJRA Systems (VULCAN), Mine Development Associates (SURPAC), Micromine and MINEsoft (TECHBASE). Data set A data set was created to challenge the capabilities of each vendor's software. The criteria used for the data set selection were: • a minimum of 300 drill holes; • the data must include topography, drill hole survey, assay and formation contacts; • the deposit was multimetallic; and • there was the potential to be mined by surface and underground methods. The data set used was an actual, complex copper ore body with a small amount of gold. The ore body was close enough to the surface to be mined by surface techniques. Part of it, though, was also amenable to underground mining. To further complicate the problem, a river ran across the area of the ore body. This presented mine planners with the problem of either moving the river or mining around or below it. The ore body had not been mined, so no data was available for the tons and grade actually produced. Data for the mine planning problem was distributed to each vendor about two months before the short course. They had the opportunity to load the data into their systems, build an ore body model and perform preliminary work. During the first day of the workshop, the vendors received problems concerning the ore body. They went to work on their machines, attempting to show short course participants how their software could help solve the problem.

Jan 1, 1992

By Richard M. Crowell, John W. Shield, Todd J. Harvey

Facing lower gold prices, gold mine operators throughout the world are seeking ways to reduce costs for treating refractory sulfide ores. Many gold mines, currently producing oxide ores, have underlying refractory sulfide deposits and the operators could extend the mine life by processing these sulfides. Fortunately, oxidation technologies for refractory ores need not be complex nor costly. GeoBiotics, Inc. has developed heap biooxidation technologies (GEOCOAT™) for treatment of refractory gold ores and concentrates. GEOCOATTM uses simple low cost unit operations common to heap leaching of gold and copper ores. The cost effectiveness and flexibility of GEOCOAT™ heap biooxidation allows mining companies to expand operations to include refract01y ore. In addition, GEOCOAT™ can be utilized to supplement or replace existing oxidation processes such as roasting, autoclaving, or agitated tank biooxidation, and to treat a lower resource grade than is currently economic. The GEOCOAT™ technology involves coating sulfide concentrates onto sized support rocks and biooxidizing the sulfides in a heap configuration. After biooxidation the concentrate is stripped from the support rock, neutralized and leached in conventional cyanidation facilities. Ashanti Goldfields Company Ltd. (AGC) produces over 885,000 ounces of gold per year from oxide and refractory ores at its Obuasi operations in Ghana. Refractory flotation concentrates are treated in roasters and in the world's largest stirred tank biooxidation facility. In August 1998, AGC and GeoBiotics jointly constructed and operated a field demonstration heap of the GEOCOATTM process at the Obuasi operations. The heap contained I 082 tonnes of support rock and 125 tonnes of concentrate. The heap was approximately 19 meters square at the base and 3.8 meters high, and ran for 88 days after which the concentrate was reclaimed. Average gold recovery after biooxidation was 91.5% with a NaCN consumption of 8.6 kg/t. Baseline gold recovery by direct cyanidation of the concentrate was 53.8%.

Jan 1, 1999

By David Muir, Slobodanka Vukcevic

Gold is commonly associated with copper minerals, particu­larly in the more geologically recent rocks of Northern Australia, Chile and the Pacific Rim. Traditionally, oxidised copper-gold ores are selectively mined and processed for gold by cyanidation, ensuring that levels of reactive copper in the ore are kept low to minimise cyanide consumption; whilst sulphide copper-gold ores are floated and gold is ultimately recovered as the by-product from copper smelting and refining (La Brooy, 1992). Very few process­ing options exist for treating copper ores which cannot be selec­tively mined or floated, and for treating floation tailings which often contain significant gold (Muir et.al.,1989). The ammonia-cyanide leach system stands out as a unique method of selectively extracting gold without copper using economic levels of cyanide (1-2 kg/t NaCN) and ammonia (1-5 kg/t). Although first patented in 1904, it proved difficult to control and predict per formance with different ores. However, recent research and development in Western Australia by Ruane (1991), Hayes and Corrans (1992), La Brooy et.al.(1991), Muir et.al.(1993), Muir and La Brooy (1993), has led to an under­standing of the mechanism, and the commercialisation of the process at the Paris Dump (W.A.), Akjoujt (Mauritania), and in the Eastern Transvaal (Laxen,1994). Efforts are now underway to pilot and develop a tailings treatment plant at Telfer following successful laboratory trials. To date, process optimisation has relied on trial and error and large numbers of tests covering a range of conditions. Thus the results are specific to the ore. At Murdoch University, process optimisation is now focused on measuring and control­ ling Eh, pH, NH3 [Cu(II)], and Cu-CN species at the optimum levels identified from the recent mechanistic studies. In this way, the optimum composition required to process any ore should be readily established and maintained.

Jan 1, 1995

By Rebecca A. Miller, Terry M. Hertel

In-pit identification of neutral waste rock at the Zortman and Landusky minesites in Montana, by visual and chemical analy­ses, will assist in proper segregation and placement of rock so that soil and water resources can be protected. The use of too few or very general segregation criteria to identify neutral waste rock can result in ineffective waste rock segregation. Conversely, the use of overly restrictive criteria can result in the unnecessary loss of valuable reclamation material that would otherwise have to be mined elsewhere and hauled to the site. Recognition of nonre­active materials can be accomplished on a site specific basis with the use of visual observation and simple chemical analyses. The choice of chemical parameters used to analyze rock samples is constrained by the length of time needed to conduct the test. These analyses must require no more than 24 hours to complete so mining can proceed without delay. Limits set for the chosen parameters must be reasonable and defensible. To achieve these objectives over one thousand samples were collected at the Zortman and Landusky minesites and clas­sified by rock type, total sulfur content, paste pH, and net neu­tralizing potential (NNP). In addition, over 22 humidity cell kinetic tests were conducted to help corroborate static results for waste rock. Another 8 humidity cells were configured in series to test waste rock blending and waste rock/limestone capping alternatives as mitigation for acid rock drainage. Leachates were analyzed for pH, conductivity, alkalinity, acidity, sulfate, Al, Cd, Cu, Fe, Mn, Zn, Mg, and Cr in some cases. Petrographic analysis, as well as total sulfur content, paste pH, and static and kinetic test results identified three geochem­ically different waste rock groups: 1) Archean amphibolite gneiss and Paleozoic carbonates and shales, 2) Tertiary syenite porphyry, and 3) other less abundant Tertiary igneous and Archean metamorphic rocks.

Jan 1, 1996

By Frédéric Flament, Daniel Hodouin, Claude Bazin

A control strategy is proposed to meet the following specifications of flotation control: minimize the variations of concentrate and tails grades and recovery while limiting the amplitude of variations of the manipulated variables. The strategy consists of determining future control actions which optimize a performance criterion over a limited time horizon. The desired dynamic behaviour of the controlled flotation plant is specified using reference models. The strategy is tested on a 2-computer plant simulator working in an environment which emulates the industrial conditions.

Jan 1, 1993

By Ronald D. Jacksha, Jason B. Coder

Wireless technologies are becoming vitally important for modern mining operations. Used for increasingly complex tasks — such as miner and asset tracking, proximity detection, teleremote and autonomous equipment operation, and environmental monitoring — the ability of wireless systems to perform their intended functions satisfactorily in the presence of other wireless systems (coexist) is critical not only to the successful operation of modern mines but also to the safety and health of mine workers. Concerns regarding the ability of wireless systems to coexist can often hinder the decisionmaking process for adopting technologically advanced wireless systems. However, with adequate knowledge of the concepts of coexistence and appropriate wireless system management, coexistence concerns do not need to be an impediment to the successful adoption of wireless systems. There are several common wireless coexistence-related fears that can inhibit adoption of wireless technology: fears that safety-related systems may not operate properly when needed, failures could disrupt production, and wireless systems may inherently require costly troubleshooting. Most of these fears can be alleviated through proactive activities.

Apr 1, 2026

By Stephen J. Brower

Located in Central Nevada, The Round Mountain Gold deposit has been continuously mined since 1977. Present proven and probable reserves are 226 Mt (250 million short tons) at 1.1 g/t (.032 oz per short ton). The current open pit mining rate of 118 Kt (130,000 short tons) per day is producing 41 Kt (45,000 short tons) per day of ore to be processed by heap leach methods. At this rate, the current reserves provide a 16 year mine life. The high mining rate and strict ore delivery requirements mandate comprehensive and realistic mine planning. The mine planning process is described in three general steps: Deposit Modeling; Mine Design; and, Production Coordination and Support.

Jan 1, 1989

By Mark E. Smith, Gerald J. Gierszewski

Introduction The purpose of this paper is to present a procedure used by the authors for evaluating and designing soil liner systems. This method is particularly valuable in evaluating various treatment schemes for chemically amended soil liners. A tabulation of laboratory test results on various soil types are presented to quantify the effectiveness of certain treatments. A typical liner design program includes developing and proving soil borrow sources, designing the cross-section of the liner system, developing construction specifications, and providing construction services to ensure the intended product is achieved. Material Source Development The first step in designing a soil liner is to identify and evaluate suitable borrow sources within an economical haulage range. This is best done in a two step approach: a reconnaissance level investigation to identify target areas and a detailed evaluation of those targets. Reconnaissance: The goal of the preliminary investigation is to locate potential borrow sources for liner quality soils. This includes all natural materials which can be compacted, chemically treated, or otherwise amended to yield an installed permeability at or below some target value. This requires utilization of all available data sources: Soil Conservation Service, BLM, aerial photos, USGS geologic maps, and project geologist records. The goal at this stage is to locate shallow deposits of favorable soil types. The Unified Soil Classification System provides an excellent first pass grouping. Clays, clayey sands and silts are the most favorable soil types, although silty sands and occasionally clayey gravels can make excellent liners, and are often amenable to chemical modification. The lowest permeabilities are generally achieved with CH, CL and MH soils. Once preliminary targets have been identified using visual examination, laboratory classification tests should be performed to further refine the selection. Testing at this stage should include gradation, plasticity and hydrometer analyses. Additionally, "preg-rob" testing should be done as early as practical. Preg-rob is a phenomenon where gold or silver ions in solution associate with the clay, or other, minerals. When this occurs, a portion of the gold or silver leached from the ore is actually tied-up by the clay and thus a reduces recovery. Testing for this consists of agitating a small sample of the soil in a solution containing dissolved gold or silver, preferably of similar chemical make-up as the solution which will contact the actual liner. The solution and soil are assayed before and after agitation to determine loss to the clay. A reliable estimate of the hydraulic conductivity, commonly referred to as permeability, can be developed from the D10 value by the use of Hezen's formula: K = 100 (D1012 This relationship is limited to soils where the finer particles do not move due to the force of flowing water (i.e.: "hydrodynamic stabilitym)(1). Additionally, the effect of platty particles on permeability is not as predictable as the effect of equidimensional particles. D10 is the sieve opening size at which 10% of the material is finer. Plasticity is also important from several standpoints. Constructability is directly related to plasticity. Very plastic clays and non-plastic silts both tend to be difficult soils, while medium plastic clays and clayey sands are generally very desirable. Post construction performance is also related to plasticity (e.g. swelling, shrinkage cracking, frost heave, etc.). Additionally, low plasticity silts and silty sands generally do not respond well to chemical amendment. Source Development: The result of the reconnaissance evaluation should be an estimate of the relative probability of developing a suitable borrow source within an economical haul distance. Of course, "economical distance" depends on the degree of handling and treatment the borrow material requires, as well as the cost of synthetic alternatives. The purpose of the detailed investigation is to prove out quantity and quality of material sources, and determine design parameters such as degree of compaction, mixing, treatment and thickness of liner. The emphasis of the testing program should be permeability and strength. Strength becomes increasingly important as the slope of the liner and the height of the heap increase. Permeability testing should evaluate the effects of compaction, water content, mixing and chemical treatment where appropriate. The effects compaction and water content during compaction have on

Jan 1, 1987

By P. K. Crane, S. C. Gambrell

The work reported herein compares the support characteristics of two different types of roof truss subjected to the same force in the horizontal tension member. The major differences between the two trusses are in the sequence of tensioning the horizontal and inclined members and in the design of the loading brackets. A photoelastic model was used to compare stresses at points along the roof of the mine opening and at the junction of the roof surface and the rib. The effects of simulated subsidence on stress in the roof and on tension in the horizontal member were analyzed. Results indicate that there are significant differences in the overall support characteristics of the two trusses. Conclusions are drawn relative to which type of roof truss provides the most favorable support if the horizontal members are tensioned equally.

Jan 1, 1986

By Andrew M. Garvie, William W. Plotnikoff, Eugenia Y. Kuo

Water infiltrating the surface of waste rock dumps transports pollutants into the environment. Lysimeters have been used to quantify the infiltration rate. To date their design has been guided by modeling under steady-state conditions. Recently a two-dimensional finite element code has been developed to model the response of lysimeters to time-dependent infiltration rates. It was used to investigate the response of lysimeters installed in a waste rock dump and subject to a monsoonal rainfall pattern. The results are presented and compared with field data.

Jan 1, 2000

By W. E. Cobb

Mining companies, as developers of natural resources, are being forced to deal with the potential long-term liabilities of past, present, and future mining operations. As discussed in a previous paper (Cobb, et al., 1987), these liabilities can include solid waste disposal corrective action programs (state or federal actions), Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), (Superfund) (state or federal actions), or natural resource damage claims (typically filed by state agencies and provisions specified in CERCLA). These potential liabilities are very real, and should dramatically impact the way a company views its exploration and development programs, and operating mines.

Jan 1, 1988

By L. G. Austin

Introduction My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rap- idly developing knowledge of how stressed, brittle solids fractured, based on the Griffith crack theory. On the other hand, reading in the grinding literature gave me: • Kick's Law, which was clearly not correct in the light of modern fracture theory; • Rittinger's Law, which was also clearly not correct; • Bond's Third Law of Comminution, which was claimed to have something to do with the Griffith crack theory, but where the connection between the two was made by intuitive pseudo- scientific reasoning I could not accept; • the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. incorrect statements abound in the literature, such as “the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1 948) and Broadbent and Callcott (1 956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1 953) in Germany. We confirmed experimentally the validity of the equations for describing batch grinding (1 962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, (Fig. 1) (Berenbaum and Brodie, 1959). Irwin (1949) showed from solution of the stress-strain solutions that a small hole in a region of tensile stress reduces stress concentration at the hole, that is, the tensile stress at the tip of a crack or flaw in a solid is much higher than the general tensile stress in the region. The longer the crack, the higher the stress concentration. Griffith (1920) hypothesized that when the regional tensile stress is large enough, then the chemical bonds at a preexisting crack tip are stretched to breaking point, as illustrated in Fig. 2. When the bonds break, the crack becomes longer, the tensile stress concentration increases, the situation is unstable and a crack opens up (propagates) a surface of tensile stress, creating its own tensile stress at the leading edge. Stored strain energy is converted to the kinetic energy of the moving stress field, which is analogous to sound propagation through the solid, so the crack tip accelerates to velocities approaching those of sound. The moving crack will pass through regions that were previously under regional compressive stress. The equations for "ideal" and "Griffith" strengths are where a is the intermolecular distance, y is Young's modulus, g is the energy

Jan 1, 1998

By H. P. Knudsen

In most open pit gold mines ore waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. While it is true that high grades and "outliers" can induce a bias they may not be the only reason for the persistent bias seen at many mines. This paper focuses on a source of the conditional bias. In this paper it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1991

By Louis W. Cope

The various types of placer deposits will be described as an introduction to the subject. The several methods and machines used for sample taking and processing will be discussed. The advantages and disadvantages of each will be covered. Included will be mistakes and pitfalls of placer sampling and sample reduction.

Jan 1, 1987

By Weijian Yu, Genshui Wu, Jian Zhang, Yong Ning

Aiming at characteristics of the soft coal roadway engineering geology and deformation, the exposure research of the soft coal seam, theoretical analysis, numerical calculation and program design were carried out. First of all, according to the disclosure, soft coal seam engineering characteristics and geological conditions in Xinxing coal mine were expounded. Meanwhile, the soft coal roadway bolt supporting axial effect, the bolt supporting transverse effect, the anchorage body mechanics strengthening mechanism and problems such as supporting strength have been analyzed. The paper pointed out that the soft coal with very small cohesive force can form a composite anchorage body under the combined action of the anchor cable group, the W-type steel band and the metal net. The soft coal body in the plastic damage area formed anchorage balance arch with a certain bearing capacity and adapted to the rock deformation, and which played an effective support role in the roof outside the balance arch of the roadway. Therefore, the full-cable support technology was proposed. And then, numerical calculation and comparative analysis were conducted on three schemes of the roadway with non-support, with combined support of “anchor bolt and cable” and the full-cable support. The results show that when the roof is supported by anchor cable, it not only controls the continued increase of the subsidence value of the roof, but also effectively suppresses the convergence amount of the floor heave value and the amount on the sidewalls of the roadway. Whether it is from the stress distribution situation, or the viewpoint of plastic zone scope, the combined support of full-cable is more reasonable than that with non-support and that with the combined support of “anchor bolt and cable”. Finally, based on the features of soft coal seam in No.2265 work face of Xinxing coal mine, the relevant support schemes were put forward, and its specific support parameters and cross-section designs were drawn as well.

Jan 1, 2017

By L. G. Austin

Development of an equation for tumbling charge and balls plus comparison to plant data suggests that the net mill power for cylindrical semiautogenous mills can be calculated from

Jan 1, 1991

By J. O. Costello

Marble is a preferred surfacing material in up-scale buildings. Its use increased in the 1870's with rising national wealth and declined in the 1950's when synthetic materials for these applications were developed. Natural marble is now limited to high-end domestic and commercial structures. Cultured marble is a paste of white marble dust and polyester resin cured in molds yielding fixtures of specific finished dimensions. Dyes incorporated at different stages in the mixing cycle mimic shades and veining of natural marble. This paper discusses the filler requirements for cultured marble production and reviews new techniques to cut and finish natural marble.

Jan 1, 1999

By Daniel McConvey

Who is the Investor? -Mainly institutional, including resource funds, other mutual funds and pension funds. -Some hedge funds. -Retail investors. -How important is the reserve disclosure to these investors? -Do these investors know the difference between a reserve and a resource?

Jan 1, 2003

By S. P. Banerjee

By international standards, Indian coal seams are not very gassy. In some of the major coalfields such as Singareni, Wardha, Pench, Chirimiri, Rewa and Talcher Coalfields practically no methane is emitted from the coal seams. Even in the coalfields of Ranigang, Jharia, Bokaro and Karanpura, all of which are situated in the basin of the Damodar river, only a few mines are faced with excessive gas emission problems. But the number of such mines is increasing as deeper reserves are being worked and already the exploitation of some of the best quality coal reserves in the country is held up pending measures for control of methane emission in these mines. Even in mines having no previous history of gas emission, methane has been met near dykes and faults. This was dramatically revealed by an explosion in Dhori colliery in 1965 wherein 268 persons got killed. Until that time, Dhori colliery was considered as a non-gassy mine but on that fateful day gas came to the workings through a freshly exposed fault plane. Similar incidences of ignition of firedamp in so-called non-gassy mines have also occured in the past, for example, in Chapui Khas and Samla Dalurband collieries, but the casualty figures were not as high. After the Dhori explosion, all Indian coal seams have been declared to be gassy, whether presence of methane is detected in the workings or not.

Jan 1, 1980

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995