Search Documents

By B. K. Mishra, R. K. Rajamani

A numerical method known as the discrete element method (DEM) is used to track the motion of individual balls in large-diameter ball mills. As a result, the en masse motion of the charge, force distribution, fall-height distribution, and energy distribution emerges from the simulation. Hence, it is possible to investigate the effect of mill diameter, liner profile and ball size distribution on the force regime created within the mill. Simulation results for 14-, 16- and 18-ft diameter mills are shown. The proportion of energy lost in high-intensity impacts and sliding ball motion is discussed. The DEM simulation technique opens the way for a closer examination of liner profiles on ball-charge motion.

Jan 1, 1992

By Flavio Moreira Ferreira

In mining industry, one of the simplest methods to smooth the standard deviation of a given ore controlled property is to build longitudinal blending piles. The effect of homogeneization is obtained due to the fact that an entire cross-section of the pile is reclaimed at each time. The variance of the pile output is the sum of the internal cross-section slice variance plus the reclaimed slice variance. While the first term is a tipical short-term parameter and is absorbed by the process, the second one may be or may not be absorbed. The goal of designing blending piles is to minimize the reclaimed slice variance. Conditional Simulation as described in this paper, is an alternative method to do it. It is devised to design longitudinal blending piles, taking into consideration economical, geometrical and statistical parameters of the ore to be blended, in order to estimate the resulting effect. It presents advantages in relation to other methods for its adaptability and flexibility in simulating pile performances.

Jan 1, 1992

By J. Twining, V. Nguyen, J. Perera

A computer code for ecological risk assessment (ERA), AQUARISK, has been developed and applied to evaluate the likelihood of biotic detriment due to exposure to acid rock drainage (ARD) from the Burkunga mine site in Australia Stream water quality monitoring data were used for the assessment and were compared with a) national water quality guidelines, b) literature derived ecotoxicology data and c) biological monitoring data. With bioavailability calculations, the code predicted that, for metals exceeding the guidelines, 44% of macroinvertebrate species above the mine and 100% below the mine would be adversely affected by the metals in the stream. This compares reasonably and conservatively with biological monitoring that showed observed reductions of 41% and 85% of species respectively at each site. Using literature data for macroinvertebrates to predict impact produced similar estimates to using data for all taxa. Use of speciation modeling also lessened the degree of reduction in the median water metal concentrations required to achieve acceptable impact (measured either by exceedence of criteria or by species likely to be affected) by a factor of 75%. This result implies significant economic and management benefits in relation to remedial engineering or water treatment options for sites.

Jan 1, 2000

By Margaret Armstrong, Arne Berckmans

The longterm aim of this research project is to find fast ways of simulating the recoverable reserves of a deposit for input into financial Monte Carlo simulations without having to conditionally simulate the whole orebody many times. The first step in this re- search is to visualize and quantify the ore tonnage T and the metal quantity Q above an arbitrary cutoff z. This paper presents detailed results for one specific distribution, the lognormal. These lead to a suggestion of a fast way of simulating QTz curves.

Jan 1, 1996

By J. A. Wallace

U. S. Steel's coal mining research activities are directed toward providing new or improved hardware and techniques to increase productivity or reduce cost. Because more than 80 percent of U. S. Steel's coal production is obtained from continuous miner sections, most of our research efforts are focused upon that mining system. Current and historical time study data show that our continuous miners only operate about 30 percent of the available face time. This limited equipment utilization is the result of the delays or interferences imposed by the non-coal-cutting phases of the continuous mining cycle. The most time consuming of these delays are: waiting-on-roof-support, tramming between alternate work locations, waiting-on-haulage-capacity, and in some mines waiting for excessive methane concentrations to clear. Because waiting on roof support is our most time consuming delay, several programs are underway simultaneously to address this problem. In one of these we are developing a patented microprocessor-based control method and apparatus to improve roof drilling performance. This increase is attained by using the microprocessor to adjust electrohydraulic valves which control drill thrust and rotation speed. The microprocessor is designed to continuously search for an optimum combination of thrust and drill rpm to maximize penetration rate at all times.

Jan 1, 1979

By L. J. Dahl, S. E. Paulson, H. L. Kuhlman

To provide basic information on the processes occurring during in situ leaching, the US Bureau of Mines developed a geologic characterization research program. This includes laboratory experiments wing leaching apparatus that can accommodate whole core samples. Whole core experiments result in a higher proportion of ore mineral contact by the leach solution than packed column experiments. They also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels of the rock. The leaching apparatus developed can be wed for either constant-pressure or constant- flow rate experiments and allows for the control of flow rate, pressure, and temperature during the experiments. Details of the experimental apparatus are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grade, AZ area.

Jan 1, 1988

By I. J. Jansen, C. L. Hooks

Successful soil construction involves prepa¬ration of an adequate base, selection of high quality soil ma¬terials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experi¬ments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construc¬tion. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By Neil Runciman, Greg Newson, Nick Vagenas

This paper discusses simulation modelling of underground mining operations at a typical mine in the Sudbury mining area in Ontario, Canada. The PC simulation software, WITNESS Version 7 Release 6.0 by AT&T ISTEL, is used to model the drilling, blasting, hauling and ground support operations. Simulation is used to investigate the development mining cycle and determine the capabilities and flexibility of WITNESS to accurately represent the mining system under consideration. The simulation study discussed in this paper provides a first step in determining the successful application of WITNESS in the underground operational aspects of the mining industry.

Jan 1, 1996

By Surendra K. Mishra

Recent land ban act has put pressure on industry to decontaminate the waste streams before they could be discharged. However, for both metal and organic contaminated wastes, there are commercial incentives to recover usable resources. Recent technology developments have helped meeting such objectives. This paper reviews developments in treatment technologies for industrial wastes. Major chemical groups used in waste treatment are summarized.

Jan 1, 1994

By Charles D. Litton

This Bureau of Mines paper describes a novel fire detector that can be used to discriminate between smoke produced by a fire and smoke produced by a diesel engine. The detector uses a pyrolysis technique whereby a sample of smoke- laden gas passes through a short, heated tube within which fire smoke particles pyrolyze and increase their number concentration and decrease their average size, while diesel smoke particles are unaffected. The detector is designed for use in mines that use diesel-powered equipment where the detection of fires is complicated because of the diesel emissions background levels of smoke and other products of combustion.

Jan 1, 1989

By G. Blackwell, E. Bozorgebrahimi

The trend in open pit mining has been to maintain cost competitiveness through economies of scale, particularly by implementing larger trucks and shovels. This paper considers the potential adverse impact of such scale adjustment, however, on dilution, maintenance, flexibility, and other aspects of operations. It examines the mine production characteristics affected by increased equipment size and attempts to quantify the impact on the overall operation. Reference is made to data from operations that have experienced a variety of equipment size ranges changes over the last decade.

Jan 1, 2003

By Nora M. Hutt, Kevin A. Morin

Geochemical static tests are a basic component of geochemical assessments and predictions for acidic drainage, and include acid-base accounting and total-metal contents. A key database for such information is the International Static Database (ISD), which currently contains more than 45,000 static-test analyses from over 200 minesites. Such large databases are useful in identifying general trends and, just as important, the percentage of exceptions. General trends and significant exceptions can be seen in the ISD by comparing one parameter against another. This paper shows that bulk neutralization potential (bulk NP) obtained from acid titration is often a good indicator of neutralizing capacity above values of 10 t CaCO3/1000 t. Other types of calculated neutralizing capacity are then compared to bulk NP to determine if they, in fact, reliably represent actual neutralizing capacity and if they can substitute for the more time-consuming and expensive bulk NP. For example, bulk NP correlates better with Carbonate NP (from carbonate analyses) and Total-carbon NP (from total-carbon analyses) than with (Ca+Mg) CaNP (from solid-phase analyses of calcium and magnesium). This means that, in general, (Ca+Mg) CaNP is a less accurate substitute for bulk NP than the other types, and thus requires intensive site-specific justification if a substitution is attempted. This also means that measurement of the frequently less-expensive parameters of total carbon and carbonate can often substitute, within site-specific error bars, for the bulk-NP titration. However, the ISD also shows that non-carbonate minerals make the primary contribution to neutralization in up to 20% of samples, so Carbonate CaNP and Total-carbon CaNP do not always reveal the full neutralizing capacity of a sample.

Jan 1, 2000

By Y. M. Jiang

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1997

By Kenneth S. Graham, S. C. Gambrell

A short term, simple roof bolt load cell which uses a birefringent (photoelastic) coating as its sensing element has been developed. The load cell is installed between the bearing plate and the nut/washer and measures the initial force after installation by the bolting machine. The load cell can be removed from the bolt and used again to measure initial force in another bolt if desired. Because temperature and humidity changes in the mine cause creep/relaxation of the coating and/or adhesive, the load cell is useful for accurately measuring force for a period of only two weeks after installation. Force in the bolt is determined by referring to a calibration curve for the load cell.

Jan 1, 1992

By R. Vogt, H. C. Mult, F. L. Wilke

INTRODUCTION At present, the capability of production planning software based on Linear Programming (LP) is still limited to the optimization of the single LP-run. This is due to the LP-model itself which cannot consider the interdependencies between individual LP- runs. With regard to planning of selective mining this limited way of optimization frequently leads to situations, where the remaining and accessible ore blocks do no longer allow to produce ROM-ore in the qualitative composition required by the ore processing plant. However, many of the aspects taken into consideration when setting up production plans built from mutually dependent LP-runs cannot be modelled in a system of linear equations. They are thus unsuited for treatment with LP and have to be taken care of by the planning engineer without any assistance by the system. The KBS currently under development is intended to assist the planning engineer in designing a production plan under special consideration of the combination of consecutive LP-runs and blending beds. It is not necessarily intended to find the optimum solution within a given planning situation which is, anyway, hard to determine due to the multitude of influences. The objective is rather to work out a good and - from the practical point of view - feasible production plan. The new aspect with respect to mine planning is the integration of expert knowledge and experiences via the KBS into the planning process in order to support the planning engineer. The planning system is being developed in close cooperation with an iron-ore open pit mine. COMPONENTS OF THE PLANNING SYSTEM The software is being developed on a workstation under UNIX and comprises the components LP, CAD-module and the KBS. The applied multi-goal LP-algorithm is an in-house development of the Department of Mining Engineering at Technical University Berlin. It was already successfully implemented within other mine planning programmes and was only slightly adapted to the specific needs of the present system. Within individual LP- runs it finds the optimum qualitative composition of ore production in the sense of the selected optimizing criterion and under the given restrictions: i.e. it determines tonnages to be mined from blocks in order to optimally meet the requirements of the ore pro- cessing plant. A CAD-module based on the commercial SURPAC package in combination with a simulation device is used to graphically depict the block model and progress of mining. Both LP-algorithm and CAD-package are integrated in the KBS. It has been decided to use the shell NEXPERT OBJECT as it is a hybrid system which supports both rule-based and object-oriented knowledge representation. MINE-MODEL AND LP-MODEL KBS have to be tailor-made for specific planning problems. Therefore, it had to be decided which specifications of the iron-ore mine should be represented in the model. As the limited possibilities of a university institute do not allow to develop a KBS for mine planning which is ready to use in industry, it was decided to concentrate on those characteristics that can be regarded as typical for iron-ore surface mines and that seemed to be suited for treatment with knowledge-based techniques. The following chapter summarizes the most important features of the mine model. The description of the requirements to the mine's sales products is followed by an outline of the applied LP-model. Mine model • The model of the mine as it is used for planning consists of • the block model of the deposit, • the mobile equipment, • stockpiles and blending bed and • the requirements to the sales products. The deposit is described by a block model which contains data on the chemical composition, LOI, grain size and tonnages. Grain size was included as it is important for the two sales products of the mine. Furthermore, it is known whichs blocks require and which don't require blasting; this is relevant to the assignment of loading equipment to individual blocks. The blocks are devided in three categories: • ore, which will directly be taken to the blending bed; • waste, which will be put on the waste dump; and • blocks which will be either transported to the blending bed, to stockpiles or to the waste dump depending on the specific planning situation. This decision is made during planning. Neighboring blocks are combined in mining areas to which the loading equipment is individually assigned. Mobile equipment comprises shovels and wheel-loaders as well as trucks. The characteristics of the loading equipment are important for their ability to load different blocks and for the permissible degree of their re-positioning etc. The mine disposes of a blending bed for homogenization of the production, of a waste dump, and of several stockpiles with different ore qualities. The requirement to make only limited use of the stockpiles for economic reasons is included in the KBS. According to long term planning two commercial products have to be produced, which differ both in grain size and qualitative composition (TABLE 1). Their mass-proportions in the blending bed have to be within a fixed range. Not considered in long term planning is the occasional need for lump ore, which occurs at very short notice and has to be produced in a "campaign-like" manner. This requires the total re-arrangement of all plans for on- coming blending beds and would therefore be ideally suited for

Jan 1, 1996

By Murali M. Gadde, Syd S. Peng, C. T. Holland

Cutter roof failure is one of the most common ground control problems affecting the safety and economy of an underground coal mine operation. Several attempts were made in the past to understand the processes responsible for cutter development and to devise mitigating measures. Yet, many cutter failures still happen and their advance prediction remains as elusive as before. One of the reasons for the impasse in predicting cutters lies in the limitations of the current numerical modeling technologies. The development and propagation of cutters is a progressive phenomenon and continuum models can only approximate this process. Since the discontinuum modeling is severely restricted by the lack of reliable input data, alternatives must be sought to better understand cutter failures using the continuum models. This paper proposes one approach using strain-softening material model to simulate the cutter initiation and propagation process. An attempt has also been made to provide some insights into the reasons for the change in cutter location at different parts of a development layout.

Jan 1, 2005

By Rodger E. Denison

The Middle Ordovician Simpson Group in the Arbuckle Mountains of southern Oklahoma contains sandstones of unusual purity. These have been exploited as glass sands since 1913 (Ham, 1945). Where quarried, the sandstones are uncemented or weakly cemented, greatly facilitating mining and processing. The origin: sedimentary setting, and lack of cementation of these valuable sands has been the source of much discussion. The lowest of the sandstone units in the Simpson is at the base of the Oil Creek Formation. The basal Oil Creek sandstone is exposed in a series of accessible quarries north of the town of Mill Creek in Johnston County. Virtually all conclusions and generalizations concerning origin of the Simpson sandstones are based upon observations made in these quarries. The three Simpson sandstones overlying the Oil Creek share many of the same distinctive qualities, and there is an assumption that they share a common origin.

Jan 1, 1999

By Richard A. Brown, Robert D. Norris

By-product metals can be a significant source of revenue for a mining operation if their recovery can be accomplished without negatively impacting primary metal recovery. The main problem encountered in separating primary and secondary metals is to selectively control the solubility of the individually important metals with¬out affecting their ultimate recoverability As a class of hydrometallurgical chemicals, peroxygens have a versatility which permits the selective recovery of individual metal species. Peroxygens function as more than simple oxidants. They are effective solubility control agents and have proven utility in complexation, precipitation, dissolution, extraction, oxidation and reductive processes Peroxygens have been used commercially to recover by-products vanadium, uranium, molybdenum, and cobalt and have proven experimentally to recover rhenium, gold, silver, manganese and zinc

Jan 1, 1983

By A. A. Mathews

INTRODUCTION When Palmer King asked me to prepare a paper for this conference, it seemed quite appropriate, since I am Chairman of Subcommittee No. 4 of the U. S. National Committee on Tunneling Technology and we are presently making a detailed study of contracting practices. Before the end of this year, we expect to publish our report containing guidelines aimed at improving our contracting practices and minimizing the problems which develop therefrom. The American construction and mining industries today are glowing examples of the ingenuity of man pitting his wits against the unknown. Without the promise of rewards commensurate with the perils faced and the effort expended, it is doubtful that these industries could have reached their present state of advancement. Nevertheless, these industries are still primitive compared to many others such as aerospace and electronics. That our present contracting practices leave something to be desired is evidenced by the fact that many of our underground projects wind up with tremendous increases in estimated cost, financial disaster, and costly dispute and litigation. The situation is aggravated by the current economic uncertainty, energy crisis, and shortage of materials. At the same time, if our industries are to develop their maximum technologic potential, we must employ contracting practices which will encourage that development. Most of the contractual problems related to underground construction are associated with risk and its management. Unless all of the ramifications of this subject are understood, it will be difficult

Jan 1, 1974

By R. A. Hodge, J. W. Murray

By an order of the Executive Council of the Provincial Government dated January 18, 1979, a Royal Commission was established under the Public Inquiries Act to: 1) Examine the adequacy of existing Federal and Provincial requirements for the protection of the health and safety of workers associated with exploration, mining and milling of uranium in B.C. and for the protection of the environment and of the public. 2) Receive public input on these matters. 3) Make recommendations for setting and maintaining standards for worker and public safety and for the protection of the environment as a result of the exploration for the mining and milling of uranium ores. At that time,and at the present time in British Columbia, no uranium mines were, or are, in operation. Exploration at a number of sites was under way and one deposit, the Blizzard deposit, with estimated reserves of 1.92 million tonnes containing approximately 4.74 million kilograms of U308 was at an advanced stage of exploration. With our Terms of Reference, and because of the diverse geology of the western Cordillera which could potentially host a broad variety of uranium, deposit types, the Commission was faced with the task of considering environmental and health protection necessary for the potential development of [any] kind of uranium mineralogy situated in [any] of the environments found in British Columbia. Over the past 17 months since that time, much has transpired, culminating in the February 27, 1980 Provincial Government announcement of a seven year moratorium on exploration, mining and processing of uranium coupled with the termination of our Inquiry before completion of the hearings. The Government sebsequently modified its decision to terminate the Commission completely, deciding instead to stop the hearing but allow time for the Commission to gather in the work that had been initiated

Jan 1, 1980