Search Documents

By Maureen D. Carmen, Joseph L. Zaluski, Gladys Beck Green

The Federal Surface Mining Control and Reclamation Act (SMCRA) requires a surface mine operator to post a performance bond before a mining permit can be issued to that operator. Release of that bond is contingent upon the completion of all required reclamation, restoration, and abatement work on the permit area. This paper explores the requirements of each of the three phases of reclamation under SMCRA, as well as provisions of four exemplar state regulations of four states that have been granted "primacy" under SMCRA. Successful completion of these requirements is a condition pre cedent to the release of performance bond liability. Failure to secure a timely bond release will have an ad verse impact on an operator's other mine permitting activities throughout the United States.

Jan 1, 1991

By R. Larry Grayson

A menu-driven, linear-programming- based, user friendly computer program was developed to assist mine managers in determining optimal longwall panel dimensions for a given set of operating conditions. A sensitivity analysis must be performed by varying key mining and configurational parameters over an expected, practical range during the optimization process. Results from analysis of a base case mine indicated that no single combination of longwall panel length and face width is optimal for all operating situations. Each mine manager must therefore look closely at his operating situation and determine the proper dimensions to minimize total mining cost.

Jan 1, 1989

By M. K. McCarter

INTRODUCTION Mining activity and basic geometry of open pit mines represent major obstacles in geotechnical mapping. Mining creates a constantly changing topographic base which may require corresponding updates of field sheets before mapping can proceed. The rapid pace of mining operations may also threaten removal of important geologic and engineering features before adequate base maps and surveyed control can be established. Maintaining such control during the mapping process is yet another complication. In addition, basic geometry yields nearly vertical outcrops. Access required for direct observation and measurement, essential to conventional plane table or Brunton techniques, may be impossible on such surfaces. Also, nearly vertical surfaces appear fore- shortened in plan view. This reduction in area provides little room for recording geotechnical detail. The difficulties encountered in open pit mapping can be substantially reduced by utilizing a modified form of plane table photogrammetry. This technique employs photographs taken from the ground as the base upon which details are recorded. The information is later transferred to plan maps using the plane table principal of location by intersection (Davis and Foote, 1953). Any change in topography can be accommodated by simply taking additional photographs. Proper spatial representation in plan view can be determined later when updated maps and surveyed control are available. In addition, horizontal photographs from the ground portray vertical surfaces as they are normally viewed thus providing maximum area for recording details. Any detail which can be identified on the photograph can be located correctly even though the actual feature is physically inaccessible. The technique presented in this paper was developed by the author for special applications at Kennecott's Bingham operation in 1970. The procedure was rapidly adopted for general use and has proven to be a practical tool for detailed investigation of potentially unstable areas (Zavodni and McCarter, 1976) and routine geological mapping (Richardson, 1975). Major advantages, other than those mentioned above, include: The speed and accuracy are greater than for conventional plane table or Brunton methods. The photo- graph represents a view from a station at some distance from the area being mapped. This vantage point allows evaluation of possible continuity of structures from one level to another which may not be evident at close range. The photographic base provides a permanent record of the topography at the time

Jan 1, 1977

By A. J. Kroha, N. Wesis

Most copper mines produce both ore and low-grade "leach" rock or acid waters that contain recoverable copper. The sulfide ores pre¬dominate, and a portion that is too low grade for milling to produce concentrates for smelting, but has to be mined and trucked away anyhow, may be leached successfully with acid in dumps. Most of this leach material consists of sulfides and silicates or carbonates, and if the gangue is such that it consumes a high quantity of acid, this factor may rule out a leach operation. There are also valuable deposits that contain mostly acid-soluble copper, or occasional sulfide ores from which a sulfide concentrate can be roasted and acid-leached to produce a copper-bearing solution. Finally, there are milling ores in which the lesser part of the copper is acid-soluble and can be precipitated with iron or synthetic inorganic precipitants that produce metallic copper or copper sulfides that will float with the sulfides. Ordinarily, ores that contain copper associated with the sulfur ion, such as in the minerals chalcopyrite, chalcocite, bornite (and others), are milled to produce a 25-30% Cu concentrate for smelting, while a lesser amount of acid-soluble copper may be converted from solution to cement copper on iron scrap. A fast-growing percentage of such copper, however, is removed from solution with exchange resins or organic compounds in organic carriers such as kerosene (solvent extraction), then eluted with strong acid and subjected to electrolytic precipitation either in marketable form or as anodes that can be refined further. From the point of view of conventional copper smelting, copper flotation concentrates and cement copper are of chief interest in this chapter. Table I is a condensed open schedule for concentrates that generally run between 25 and 35% copper, and much less frequently as low as 12-15% or as high as 65-75% copper, the former being due to intimate relationship with pyrite (like the former United Verde Extension), and the latter representing such ores as the Bolivian Coro¬coro ore in which the copper is in the form of chalcocite in sandstone. These extremes are no longer common. When they occur, a special purchase schedule has to be negotiated. Included in Table 1, copper precipitates (cement copper) generally run from 70-85%a copper, and the same basic purchase schedule is used as with flotation concentrates. Sulfide Flotation Concentrates The sulfide copper concentrate produced in the mill as a flotation froth, with water then added for transportation of the heavy mineral particles from the flotation cells to thickeners, may run 60-80% water by weight, and the removal of water down to 25-50% by weight by means of thickeners, followed by further dewatering by continuous vacuum filters to 7-18% moisture by weight (depending on size of solids by screen analysis and also by content of clay) is a critical operation. Mill operators would like to produce a filter cake with 7-9% moisture content, but even with the help of steam on the filter this desirable condition is seldom realized when the concentrate is as fine as 80% -325 mesh. More commonly, the final concentrate is reground in pro- to produce best copper recovery and grade of concentrate (or molybdenite separation). In those cases, increasingly frequent, the filter product may not be a cake at all, but a mud that is hard to handle-even requiring a thermal dryer. Greater difficulty of form¬ing a manageable cake often comes from the copper-molybdenum separation by flotation, because the alkaline sulfides and hydrosulfides, or cyanide, or other similar reagents used for the separation, may leave the now relatively molybdenite-free copper concentrate even more difficult to filter. Handling a wet filter cake is difficult enough when its destination is only a short distance away-a matter of yards rather than miles. In those cases the filter cake may be thermally dried near the point of production, using rotary or multiple hearth, or fluidized-bed dryers. Alternatively, the concentrate may be pumped or carried in slurry form to the smelter and filtered there, or it may be spray-dried and compacted. For transportation to a smelter just a few miles to a few thousand miles away by ship or railroad other factors may be important, such as: in shipping by sea, avoidance of spontaneous combustion; in shipping by rail, losses by leakage if too wet or by wind and sun if too dry. It is the responsibility of the millman-usually the mill superinten¬dent-to make sure that his concentrates are in satisfactory condition when they leave the mill so that they meet these requirements: 1) They must have been accurately sampled and dry-weighed, the latter meaning that a moisture determination and gross weight must have been taken. 2) They must be dried sufficiently when necessary to prepare them for safe transportation. 3) They must arrive at the smelter with reasonable likelihood that they can be check-weighed and sampled fairly and equitably,

Jan 1, 1985

By J. M. King, C. J. Boggs

Acquisitions of mineral properties and companies can saddle the acquirer with unexpected and substantial liabilities and obligations incurred by the acquired or selling company that are not readily apparent from review of the company's books or files. This paper will address selected areas of concern, such as environmental and reclamation liabilities, problems of foreign ownership by the buyer or seller, pension obligations, plant closing laws, effective title review, land use and zoning.

Jan 1, 1992

By Zbigniew Hladysz

INTRODUCTION In the Polish coal mining industry, the Upper Silesian coal basin has an important position. It contributes over 98% of the total coal production of Poland which reached 193 mt in the year 1979. In view of the significant urbanized area in this region as well as the industrial potential, it is important to protect the surface by stowing the mined out underground workings. Approximately 18% of the total production is mined from longwall faces with stowing. However, caved longwall faces are most popular. In the upper Silesian coalfield, approximately 337 highly mechanized longwall faces are in operation. Out of these 337 faces, 301 longwall faces are caved. One of the main requirements for effective and safe coal extraction is a suitable method for strata control. We can divide the complex process of strata control into four steps: 1. Strata investigations 2. Selection of supports for roadways 3. Selection of supports for longwall 4. Rock bursts and other hazards protection STRATA INVESTIGATIONS Estimation of the structure and physico-mechanical properties of the rock mass surrounding the workings is an important constituent of strata control. These factors definitely influence the rock stability, support load, working conditions as well as the mining technology. Complex methods of strata investigations involve a set of indicators enabling the estimation of the stability of the roof rock, strength of the coal seam and load bearing capacity of the floor. The basis for the evaluation of roof stability for a coal seam is the classification according to the resistance to bed separation (1). The bed separation resistance is equal to the strength of the rock in tension perpendicular to the bedding plane. In order to properly classify a rock, it is indispensable to make continuous profiles of the bed separation resistance from the immediate roof up to a distance of three times the thickness of the coal seam. The profiles are developed by utilizing mine roof investigations with the hydraulic borehole penetrometer. (Fig. 1) The penetration resistance is determined by the critical pressure required to cause crushing of the rock by the penetrometer indentor (2). The classification of roof rocks and their ability to cave spontaneously during longwall mining is shown in [Fig. 2]. The measurement of the critical pressure also allows for the determination of the compressive strength of the rock, the index of workability and roof fissuration.

Jan 1, 1982

By J. L. Hendrix, M. Ahmadiantehrani, G. Ramadorai

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, hypochlorite consumption and concentration, and bed height on total gold extraction. At high pH, hypochlorite stability increases and thus, hypochlorite consumption decreases. At room temperature, total gold extraction is proportional to hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10% and 80% are achieved at 12 and 167 lb/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption, gold extraction increased with decreasing ore bed height. Finally, using calcium hypochlorite results in higher gold extraction than using sodium hypochlorite at a fixed hypochlorite consumption.

Jan 1, 1992

By J. Devon, D. L. Ewart

Long-term coal mining plans are often based on attainment of an average cost of coal. This is achieved by blending low- and high-cost coal production. Coal that is beyond the economic limit of the reserve is mined in a misguided effort to improve reserve recovery. Long-term contracts should be least cost-based and generate the best net present value from the economic reserve within the context of a rational mine plan. The selected economic reserve should he mined on a low- to high-cost basis to benefit from the time value of money.

Jan 1, 1996

By Thomas V. Falkie

Of the various critics of federal energy and minerals policy we are hearing these days--and they are legion--few make their points more vividly than our fellow SME member and eloquent spokesman for the mineral industry. Mr. Eugene Guccione. In a moment of comparative mellowness. Mr. Guccione recently characterized Washington's time-honored legislative and bureaucratic machinery as a case of "...scientific illiterates asking the incompetents to do the unnecessary." I hope the prevailing industry view of government is not quite that harsh, and yet one cannot deny that government intervention is indeed pressing in on the mineral industry with increasing force. What is happening today in Washington and in state capitols will have enormous impact--both short and long term--on the future of coal and mineral production in the United States. Symptoms of this trend are everywhere. In the first place, there is a sentiment, widely held and still spreading, that the government must become involved-- that no matter what the problem, the solution lies in more government intervention. Free enterprise versus statist, reflex reaction organizations. When it cones to regulation in the resource field, there is too often a tendency to start out by assuming guilt on the part of the mineral industry. This can lead to laws governing mineral recovery that are more punitive than constructive...laws drawn up with little research into the scientific or economic considerations involved.

Jan 1, 1975

By Danqing Xu, A. W. Khair

This paper presents an analysis of mechanism of secondary fragmentation and respirable dust generation due to regrinding. In continuous miners, the recovered coal and uncleaned coal from the previous cutting cycle have to be transported through the circumference of the cutting drum, subjecting the coal to regrinding. Such regrinding comminutes the coal material utilizing kinetic energy, thus creating a great amount of respirable dust. The mechanism of a single particle subjected to regrinding is analyzed. A mathematical model is developed to describe regrinding in field conditions. The important factors influencing the comminution process are discussed in detail. Utilizing three types of coal seams, laboratory experiments are being carried out with an Automated Rotary Coal Cutting Simulator (ARCCS) to quantitatively evaluate the effects of some particular parameters, such as cutting velocity, depth of sump and properties of coal material, on breakage and on the amount of respirable dust generated. An orthogonal fractional factorial experimental arrangement is used to optimize experimental design. Preliminary experimental results are presented.

Jan 1, 1991

By L. R. Shotwell, C. F. Voss, R. J. Bastian

Pacific Northwest Laboratory (PNL) currently supports the U.S. Department of Energy's Office of Civilian Radioactive Waste Management in developing and evaluating analytical methods for assessing the suitability of sites for geologic disposal of high-level radioactive waste. The research includes consideration of hydrological, geomechanical , geochemical , and waste package components and the evaluation of the degree of coupling that can occur between two or more of these components. The PNL effort and those of other research groups investing potential waste sites in the U.S. and abroad are producing a suite of computer codes to analyze the long-term performace of the proposed repository sites. This paper summarizes the ongoing research in rock mechanics at PNL involving flow through jointed rock. The objective of this research is to develop a methodology for modeling the coupled mechanical-hydrological process of flow through joints and then attempt to validate a "simple" model using small -scale laboratory test data as a basis for judging whether the approach has merit. This paper discusses the laboratory tests being conducted to develop s joint behavioral constitutive model for the numerical method under development and the modeling approach being considered.

Jan 1, 1986

By Jack S. McPartland, Gene E. McClelland

It is advisable, for any heap leach project, to develop an historical metallurgical data base to predict production heap performance before ore is mined and placed onto the heap. A data base would include results from: interval assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples; and those results plus column leach test data on diamond drill core or bulk ore composites. Subsequent larger scale heap leach test data can then be compared to the historical data base, to blast hole composite data during mining, and eventually to production data. This paper does not discuss metallurgical comparisons between assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples, but does discuss metallurgical comparisons from bottle roll tests, laboratory scale column leach tests, and pilot scale heap leach tests on core and bulk ore samples with operating data for three U.S. commercially producing heap leach operations. Provided that representative core or bulk samples are used for evaluation, heap leach test results accurately predict or understate the success of the commercial operation and remove most of the uncertainty from the investment decision.

Jan 1, 1990

By H. Tutu

The legacy of gold mining operations continues to affect water quality in the Witwatersrand Basin in South Africa. The acid mine drainage (AMD) emanating from the tailings dumps liberates heavy metals from the ore minerals. The objective of this study was to characterise the geochemical processes that are important in understanding chemical evolution of polluted water in the study area. Analytical results for water samples collected in the catchment of the study area generally showed elevated concentrations of heavy metals in the vicinity of tailings dumps and mining operations and a decrease in the distal. Dams and wetlands, despite their proximity to the tailings dumps, recorded low concentrations of heavy metals and other pollutants. The characterisation of AMD was summarised in a conceptual model in which plots of redox potential versus pH and electrical conductivity versus pH were identified as the most important sub-models that captured the gross physical-chemical characteristics of polluted water and its interaction with the environment.

Jan 1, 2006

By M. N. Brodie

The paper examines the requirements for electric power used in concentration and dewatering circuits, the effects of plant capacity and process type, the restraints imposed by the primary supply and applicable codes and outlines the procedure by which effective design is carried out.

Jan 1, 1986

By Guiseppe Bonifazi

This work applies the definition of "separation function" already introduced in the paper presented at the XVIII IMPC. This 'function" (defined for a certain size distribution after comminution of an ore) refers to the recovery distribution of a mineralogical species in a product made up of all the particles having at least a given content of that species. Many tests would be required to determine the liberation function for each mineralogical species, particularly for complex ores. Several stages of comminution would need to be examined and the mineralogical composition of the particles of each grain size class would need to be analyzed for each process step. A quick and dirty method is shown for obtaining the "separation function". It is based on the processing of data from topological maps of polished and/or thin representative sections of ore. By superimposing grids of different sizes over these maps and with appropriate combinations of mesh sizes, it is possible to simulate the grain size distributions linked to different stages of comminution and then evaluate the mineralogical composition of each grain. The procedure is carried out full automatically and can simulate a complete treatment circuit, imposing cut-off grades for the products at each separation phase. It is also possible to predict the results of treatment processes that involve grinding phases. The procedure has been successfully applied to complex ores containing several useful components.

Jan 1, 1995

By David M. Mchaina, Allan E. Hall, W. C. H. Kruining, Alan Coode, Stephen Hardcastle

This paper details an investigation into the feasibility of recirculating mine exhaust air in Saskatchewan potash mines. This project was initiated following a previous study at Ruttan Mine, Manitoba, which indicated that recirculation of exhaust air to reduce winter heating costs was feasible. The potash industry was selected for study because the mines use a minimum of blasting in their production methods and the exhaust temperature is significantly higher than that of most metal mines. These factors simplify the monitoring system required and have the potential for greater waste heat recovery. A series of measurements of underground mine pollutants was made at the main exhaust and intake shafts in order to determine the feasibility of introducing controlled recirculation of exhaust air. An experimental recirculation circuit was created by opening two existing doors situated between the return and intake shafts. During this recirculation trial, the air quality parameters at the intake, mixed intake and exhaust measuring stations were monitored. The results obtained from a questionnaire circulated to the regulatory agency and the major potash producers together with results obtained from underground field studies at Central Canada Potash (CCP) Division of Noranda Minerals indicated that controlled recirculation of mine exhaust air has potential application in these mines either to reduce heating costs and/ or to increase the face air quantities. A recirculation system is to be designed in conjunction with CCP and the Saskatchewan Ministry of Labour, Mine Safety Unit to attempt to implement a working recirculation system for CCP.

Jan 1, 1989

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By Z. B. Yin, R. W. Bartlett, P. R. Taylor

Tube furnace experiments have been performed to evaluate the lime roasting of pyrite in air. The sulfur volatilized was measured over time. Variables studied included: form of lime, sodium sulfate additions, temperature, air flow rate, lime to pyrite weight ratio and pyrite particle size. It was found that more than 98% of the sulfur can be retained at a reactor temperature of 650°C, with a slight excess of calcium hydroxide. The roast products are primarily hematite and calcium sulfate.

Jan 1, 1990

By P. Somasundaran, S. E. El-Mofty

A comparison of the IMC Anionic Process and the CLDRI Process, based on pilot plant testing of waste pebble by Jacobs Engineering is presented. Estimated costs for constructing and operating a beneficiation plant utilizing dolomite flotation are given. Research to develop practical flotation processes for removing dolomite from low-grade phosphate rock has been a high priority for the Florida Institute of Phosphate Research. The Institute funded the above pilot plant programs in 1998 and 2000. The Florida Phosphate industry currently deals with the increasing dolomite content of ore reserves by practicing selective mining. Heavy media separation plants installed at two mines to remove dolomite from pebble are not being operated. The flotation separation of dolomite from waste pebble requires that the flotation feed be ground. Grinding liberates the mineral species and produces particle sizes small enough to be floated. Only two dolomite flotation processes, the IMC Anionic Process and the CLDRI Process, have been successfully demonstrated on flotation feed that has not been deslimed after grinding. Deslimed flotation feed, relative to undeslimed feed, has improved flotation performance and reduced reagent consumption. However, for the above mention processes, undeslimed ground feed increases the yield of concentrate because the phosphate desliming losses are avoided.

Jan 1, 2002

By R. J. Gochin, G. D. Schena

Mineral processing options and technical innovations should be financially assessed. Indeed technical feasibility alone does not offer an adequate process selection criterion. An appraisal by the use of engineering economics principles leads to a more efficient evaluation and selection of feasible mineral processing solutions. Financial consequences of different options synthesised by profitability indices allow better decision making. Selected examples derived from real world problems are used to illustrate the potential of engineering-economics methods applied to mineral processing.

Jan 1, 1995