Search Documents

By Amoussou Coffi Adoko, Shevaune Zeng, Sebastian D’Hyon, Gareth Kennedy, Eleonora Widzyk-Capehart

Inertization of coal dust with stone dust is a common control implemented within underground coal mines to mitigate the hazard of a coal dust explosion. To achieve adequate inertization, the total incombustible content (TIC) of the coal/stone dust mixture is required to meet certain percentages depending on the risk and relevant legislation. Current methods for determining the TIC of a mixture involves laboratory analysis, colorimetric comparison, or the use of portable instruments. This paper provides preliminary analysis of determination of a sample’s TIC in real-time with chemometric modelling, using portable instruments employing near-infrared (NIR).

Feb 1, 2024

By Palmer C. Sweet

Mining-related wastes, which are increasing, are being utilized more and more as valuable resources in Virginia. The Environmental Protection Agency (EPA) divides mining-related wastes into two categories: those generated from mineral extraction and beneficiation and those generated from mineral processing. Materials from both categories are produced in Virginia, where waste (by-product) materials are present at a variety of mining sites and processing plants; some of which have been exploited for various uses in the past and/or present. These materials include: used concrete recycled for roadbase material; pyrite coated with magnetite for use in portland cement; minor amounts of fly ash for use in concrete block, lightweight aggregate, and flowable structural fills; granite and diabase quarry fines for use as agricultural and asphalt filler; lime kiln dust for use in neutralizing and stabilizing coal refuse; soapstone aggregate for use in terrazzo heat retention panels; kaolin for use as a filler product and as an ingredient in white cement; slate quarry fines used as landcover and combined with aggregate for crusher run and as a filler in asphalt; and coal refuse for use as fuel in a lightweight aggregate plant. There are some materials available that have never been utilized, although several ideas were investigated to turn them into usable commodities. One such material is a high-alumina scrap produced as a by-product at a ferrovanadium processing plant. However, large quantities of waste materials from metal mining, industrial mineral, and fossil fuel operations remain to be disposed of in an environmentally safe and economic manner. In 1989, almost one million tons of fly ash were produced from burning of coal at eight coal-fired power plants in Virginia. Present uses for this waste such as an ingredient in concrete block, concrete aggregate, and in structural fills cannot dispose of all the available material; however, increased use of fly ash as a soil/rock substitute for structural fills and embankments may solve the problem of its disposal. Another waste material is calcium carbonate precipitate paste produced at a lithium carbonate processing plant and presently being used for back filling an on-site inactive underground limestone mine. Flue gas desulfurization (FGD) wastes in the form of CaS04 will probably increase threefold. If this material contains a minimum of 95 percent gypsum and negligible chloride, it may have a value to a wallboard manufacturer as we move toward the year 2000. Thought must be given how this increasing waste can be disposed of in an environmentally safe manner.

Jan 1, 1995

By Dave Willis

In ME'S 1994 Powder River Basin (PRB) coal transportation article, the lead author described some destinations pursued by the railroads. As with many destinations, though, they turned out to be merely stops on the way to places that have yet to be reached. Along the way, the railroads discovered that making it better is a continuous process, not just something done in several phases. This was always known but not at the awareness level that exists in 1998 railroad environments. This update of the 1994 article includes railroad companies' plans for the future of rail transportation in the PRB.

Jan 1, 1998

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By A. D. S. Gillies, A. Haghighat

"A study has been undertaken at the Missouri University of Science and Technology (MS&T) limestone Experimental Mine to determine new fans set up and wiring options.to install additional mine ventilation capacity. Selection for main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Available fans for ventilating the mine are Joy and Alphair axial fans each of 24 kW each and two Spendrup booster fans of 12 kW each. The installation of main mine fans on the surface and underground entails numerous considerations. Design of a ventilation network for the Experimental Mine incorporating surface and booster fans has been accomplished using Ventsim Visual program software. The ventilation network has been separated into two segregated parts. A main surface fan and a booster fan have been used in each segregated part of the network. The mine has had a vane axial Joy fan in place for many years. The Alphair 4800 VAX 1800 full blade adjustable pitch vane axial fan was selected and installed as the other surface fan and eventual replacement for the Joy fan. Main surface fans have been connected individually to booster fans in series. The Alphair main surface fan has been installed vertically. Four different wiring options and related cost estimations for addition of the new main fans to the ventilation network have been considered. The analysis resulted in an innovative steel frame design used to allow the fans, when necessary, to be moved to the side of the shaft so that blast pressures do not damage the blades. INTRODUCTION Main fans are the heart of a mine’s ventilation network and play a key role in supplying required airflow (Haghighat, 2014). The Missouri S&T Experimental Mine has been developed in uniform limestone with few stratigraphic features. The mine floor is approximately horizontal and water drains well. A study has been carried out on MS&T Experimental Mine. Selection of main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Ventsim Visual computer simulation has been used to assist in design of the ventilation network. Wiring circuits, fan foundations and flexibility have been considered as the three main parameters for surface fan installation at the Experimental Mine. Two surface and two underground wiring options and three surface set up options and related cost estimates for the new surface fan system were investigated. Frequent use of explosives in the mine occurs throughout each year. Flexibility in changing the position of a surface fan is important. A number of options have been considered for the location of a vertical main fan positioned on the upcasting shaft. The mine is used for a variety of purposes and flexibility has a high priority amongst design considerations."

Jan 1, 2015

By M. Henneman, M. Kosma, M. Eyll-Vetter

"For a long time, the recultivation of depleted opencast mines and operating systems was aimed at restoring the original state. The focus, as desired by policy-makers and the local population alike, was on restoring high-quality agricultural land and on creating reforested areas of value that suit their location. Until the turn of the millennium, recultivation measures were only rarely the subject matter of public planning processes beyond these general objectives. They were never regarded as nucleus and origin of sustainable structural developments. The rehabilitation of inactive lignite opencast mines in central and eastern Germany brought about a change in mind-set that understood recultivation to be a unique opportunity to completely redesign a landscape and gear it towards the future in the Rhenish mining area as well. The ""Inden residual lake"" and ""terra nova"" projects, planned in the last 10 years in cooperation with policy-makers and authorities, are two undertakings that provide sustainable structural impetus for the future today."

Jan 1, 2011

By J. W. Stevenson

At this 5th U.S. Mine Ventilation Symposium I would like to focus your attention on safety and the contribution of the ventilation engineer over the past 50 years. This conference affords us the opportunity to express, to listen, and to learn. As ventilation engineers it is indeed an exciting time--a time that not only stimulates our imagination but also pin points our aims in our quest to obtain zero fatalities by the year 2000, the goal expressed by William J. Tattersall, Assistant Secretary of Labor, Mine Safety and Health Administration. In the past, coal mine ventilation has often been unfortunately synonymous with explosions and resulting fires. Those not familiar with us do not recognize the painful evolution of the coal mining industry and particularly the evolution of mine ventilation. To put my presentation into perspective, I recently reviewed a U.S. Bureau of Mines Bulletin No. 586 - "Historical Summary of Coal-Mine Explosions in the United States 1810 - 1958 prepared by H. B. Humphrey Mining Health and Safety Engineer. This bulletin was published in 1960. Mr. Humphrey stated "In 1946, factors contributing to the explosions occurring from 1941 to 1945 were: (1) The rapid increase in the use of electrical equipment at face regions where gas and dust are most likely to be found; (2) the increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost, which in many mines has resulted in neglect of even rudimentary precautionary measures; (3) multiple-shift operation without provision of time for adequate maintenance of equipment, effective rock dusting, and testing for gas; (4) decrease in supervision owing to demands on supervisors for maximum tonnage and loss of competent supervisors to other employment; (5) lack of effective supervision, owing to numerous new conditions, some of them war-connected; (6) inability to obtain adequate equipment repair and replacement parts; (7) shortage of labor and inadequate training of coal-mine workers; and (8) failure of both miners and mining officials to show regard for safety in changing from hand-loading to mechanized methods". Most of the eight factors listed by Mr. Humphrey continue to affect our work lives as mining engineers. The increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost has never changed. The local and regionalized coal industry of the 40's is today competing against the world coal market. Our mines work or shut down based on cost. This has always been the case. During the five year time-frame Mr. Humphrey was documenting, 345 miners were killed in major explosions. A major explosion was one in which five or more miners were killed in a single accident. In addition, 105 more miners were killed in minor explosions for a total of 450. What a wanton waste of life. What fears, anxieties, miseries, and sufferings were created by these accidents. However, we must remember and keep in mind that the coal mining company officials, engineers, and foremen, the governmental agencies- federal, state, and local - were using the technical tools and knowledge available to operate the mines as safely as they could. Obviously mine ventilation engineering technology was woefully inadequate.

Jan 1, 1991

By Graham Taylor, Mandy Agnew

Hardpans developing in tailings storage facilities (TSF) in Australia have been investigated in relation to Acid Rock Drainage (ARD) generation. This research had three main aims. Firstly it was to obtain an understanding of the physical and chemical characteristics of tailings residues which support the in-situ formation of cemented layers and hardpans. Secondly it was to examine how effective hardpans are at reducing ARD generation, and thirdly it was to investigate the promotion of hardpan formation to inhibit ARD and pollutant generation. This paper presents the data collected during investigations into the effectiveness of hardpans to reduce ARD generation. Three basic types of hardpans have been identified and examined: laterally extensive surface hardpans, laterally extensive cemented layers; and laterally discontinuous hardpans developing in locations of seepage. Their mineralogy, morphology, lateral extent, depth and rate of formation are dictated by sulfide and gangue mineralogy and content, milling and depositional techniques of the tailings and the climate. As the sulfides oxidise, acid and heavy metals are generated, while gangue mineral degradation is enhanced, adding to elemental loads. These liberated ions are then available for precipitation of secondary mineral cements through concentration during evaporation. In TSFs where hardpan development is restricted by mineralogy, grain size or climate, hardpan formation can be enhanced in seepage zones (eg. seepage from waste rock dumps) where tailings are exposed to seepage waters laden with heavy metals and sulfate. The effectiveness of hardpans in the inhibition of ARD generation is dependent on reducing oxygen diffusion and water infiltration into the underlying tailings. A reduction in water infiltration will diminish the transport of contaminants developed during sulfide oxidation and subsequent reactions. Water and gas movement through the hardpans at the CSA (Cu, Zn, Pb) and Elura (Pb, Zn, Ag) mines has been investigated. Permeability tests indicate the hardpans have reduced the infiltration rates by 10 to 100 times that of the fresh tailings. Oxygen diffusion rates were calculated and were shown to be up to 1000 times lower in hardpans than in fresh tailings. Such decreases are explained by persistent elevated 'degrees of saturation' within the hardpans. These conditions were verified using a conceptual model of sulfide oxidation reactions, which allowed comparisons of diffusion coefficients with modelled and observed depths of oxidation within the tailings impoundments.

Jan 1, 2000

By E. Pardo-Igúzquiza

Most mining applications of geostatistical simulation are to the simulation of quantitative variables, such as grade. In many instances the occurrence of quantitative variables and the values they take are controlled, at least partially, by qualitative, or categorical, variables. Examples include quartz-vein controlled gold orebodies and stratigraphic silver/lead/zinc deposits. In these cases a realistic simulation must include geological controls on the spatial distribution of the simulated quantitative variables. This paper describes extensions to, and algorithms for, the truncated plurigausian method of simulating categorical variables. The categorical variables are modelled as indicator random functions that represent the presence/absence of the variable at spatial locations. Stochastic images of the distributions are obtained by truncation of realisations of two Gaussian random functions simulated at the same locations. Parameters required are the thresholds for truncation of the Gaussian variables and the covariance structure of each Gaussian random function. These parameters are estimated from the experimental proportions of each variable and indicator direct and cross semi-variograms. A detailed case study is shown in order to illustrate the procedure, to discuss the results and to present the algorithms for plurigaussian simulation.

Jan 1, 2002

By Dwight R. Coles

The solving of complex metallurgical flowsheet calculations by hand is, at best, a tedious job which often proves that engineers, too, make mistakes. The high cost and long lead time associated with manual flowsheet solutions have led several organizations involved in research, development and construction of extractive metallurgical processes to search for computerized systems which will solve flowsheet calculations. Although design flowsheet programs have been developed by the chemical industry, the ability to solve flowsheets involving particulate solids is usually overlooked. A new computer applications system has been developed at Fluor Mining and Metals which has been designed to accommodate the type of design flowsheets required by the minerals industry. By employing the sequential modular computation technique, a library of metallurgical pro- cessing routines may' be accumulated which are used by a universal executive system. This technique enables rapid solution of new process) .flow- sheets with only a minimum of additional programming effort. The implementation of the FLEXMET flowsheet solution system is the subject of this paper. Some of the major features of the system which are examined include interactive input data handling, automated flowsheet calculation order arrangement, flexible accomodation of unit operations models and advanced management of recycle and specification control calculations.

Jan 1, 1982

By G. M. Rao

It has been a universal observation that rich grades of ores and minerals are getting depleted, simultaneously the demands for civilization are ever increasing coupled with occurrence of poor grades of ores and minerals posing a problem to the processing engineers. At the same time, the cost of mining and milling are increasing, creating a situation where the management has to handle and process low grade ores at an economic level keeping environmental stipulations and control to be safeguarded which has been an additional cost for the management to comply with.

Jan 1, 1994

By William Laird

In the process of mining coal today, our greatest asset, the coal miner, is faced with the indirect and direct consequence of underground mining operations. The indirect considerations may be the rank of the coal seam, the amount of overburden, geological factors, seam permeability and cracks. The introduction of newer, bigger and faster coal-producing face equipment having the capability to cut or rip through the bedding planes, cleats and micropores of the coal seam brings about rapid liberation of gas accompanied by greater concentrations of coal dust, has exerted a direct consideration and greater demand upon mine ventilation systems and dust control. The purpose of mine ventilation is to provide sufficient pure air to the miners working underground and to dilute, render harmless, and carry away all the dangerous and noxious gases. The mining operations which create coal dust are cod cutting, drilling, blasting, loading, hauling, dumping and movement of face equipment. The created fine dust causes the propagation of explosions. When quantities of coal dust with no methane present are raked in a sufficiently dense cloud in the presence of a source of ignition, an explosion is possible.

Jan 1, 1980

By G. Oswald

The fatty acid flotation process has been used to produce phosphate for decades, yet the chemical mechanism involved has never been thoroughly investigated. A basic knowledge of the process is lacking, and as such, industry has had to develop their own guidelines for the design and operation of conditioning and flotation equipment. These guidelines are the result of many trial and error attempts, and are not by any means universally endorsed. There are almost as many opinions about how to operate a plant as there are practitioners of the art. This paper covers the currently recommended rules for design as viewed by one practicing phosphate metallurgist.

Jan 1, 1993

By A. S. Mallicis, Li Xiawoei, P. W. Weiblen, I. Iwasakl

Platinum group metals (PGM) are often found in close association with arsenide and sulfarsenide minerals in copper-nickel bearing gabbroic rocks. Major losses of platinum in flotation have been attributed to the susceptibilities of the arsenic minerals to oxidation and subsequent losses of their recoveries in cleaner flotation stages. The use of a nitrogen atmosphere in grinding and in flotation, the effectiveness of activation for improving their floatabilities, and the role that electrochemical interactions play not only between grinding media and minerals, but also among different minerals, are discussed.

Jan 1, 1989

By James A. Deane

Strip mine reclamation Fs the process of restoring the land affected by the mining process to its most productive use. This can be timber production, pasture, crop land, wildlife and/or recreational use. The mining companies must determine, through the advice of their technicians, what the most advantageous use of the land will be. If the Company does not own the surface, the owner or owners must be contacted to determine their desires as to how the land should be reclaimed. Many times, in making the plans to restore an area with vegetative cover, the watershed and the quality of the water in the area is overlooked. The water itself must be an integral part of the reclamation plan. Many lakes and/or pits can be created with proper planning. In areas in the Midwest, where lakes are a scarcity, these strip mine lakes can become storage reservoirs for large amounts of water, They can help control runoff and low flow augmentation. The strip mining operation will affect the watershed regardless of whether a reclamation plan in made or not. It is up to the reclamation technician to see that the plan benefits the watershed instead of affecting it adversely. This can be done during the operation by intercepting the water before Pt enters the active pit. Diversion ditches above the highwall will handle the runoff water from the watershed. Water that does gain entry into the pit should be removed as quickly as possible. If the rules and regulations adopted by the Ohio River Valley Sanitation Commission in Resolution 5-60 are followed, water encountered during the operation can be handled with little or no adverse effect to the receiving watershed.

Jan 1, 1965

By S. L. Huang, J. D. Rockaway, N. B. Aughenbaugh

Shale has long been recognized for its tendency to swell when exposed to the atmosphere. Interaction of moisture with exposed shale strata can cause serious ground stabi1ity problems, since the initial strength of a shale is reduced if the material is sensitive to moisture variations. In this paper, the authors present a classification system to estimate the response of swelling generated within shales. This characterization of the swelling potential is based upon plasticity, susceptibility to moisture, mineralogical constituents of clay size particles, and fabric. Use of this classification system in conjunction with other existing rock properties tests will provide data for more rational engineering design.

Jan 1, 1986

By R. C. Bunge

The selective flotation of semi-soluble salts with fatty acids is often negatively affected by the interaction of the potential determining cation with the ionic surfactant in bulk solution. This problem can be avoided by floating at low pH which involves the emulsification of the collector. The research presented here focuses on the influence of the Ca2+ ion on the flotation of fluorite with palmitic acid at low pH. Our results show that the surfaces of collector emulsions are dominated by precipitation phenomena similar to those encountered in bulk. In turn, fluorite in palmitic solution at intermediate pH displays surface properties similar to those of the collector by itself. This may be due to two alternative mechanisms (i) adsorption of bulk precipitate on the fluorite surface or (ii) the formation of a bilayer of surfactant ions on fluorite. Possibly, both mechanisms occur simultaneously.

Jan 1, 1993

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By C. Abbruzzese, L. Piga, P. Fornari, S. Ubaldini, R. Massidda

The effects of certain variables on the extraction of gold by thioureation have been investigated on a quartzose gold-bearing ore using a statistical multifactorial strategy. The factors taken into consideration were milling time (which corresponds to a given grain size), oxidant concentration, thiourea concentration and liquid/solid ratio. The influence of these four variables was ascertained first by a full factorial design at two levels for each variable (16 runs). This permitted the estimation of first-order effects of the factors affecting the process. Then 9 runs were added whose levels were both in the centre of and outside the axes of the previous plan thus originating a central composite design. This permitted estimation both of second-order effects of the factors involved and of parameters of a second-order polynomial model. The results show that extraction of gold depends only on milling time and oxidant concentration, at least in the experimental range considered. The equation fitting experimental data, as calculated by the least squares method, allows a response surface to be drawn. Due to the low gold grade of the ore (6 ppm) statistical analysis could lead to contradictory results, hence strict observance of Gy's rules for sampling and very accurate and precise chemical analyses were required.

Jan 1, 1995