Search Documents

By J. H. Rowland

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on the effectiveness to extinguish conveyor belt fires. The four different types of suppression systems were water sprinkler, deluge type water spray, and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 72-in-wide fire resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 500-550 feet per minute (fpm) and 1350-1500 fpm. Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to extinguish any smoldering belting was greater than the current MSHA regulations require. MSHA regulations only require 10 minutes of water supply to the suppression system. In the test set up neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 500 fpm air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test set-up, arrangement of the fire suppression systems, and conclusions regarding the effect of air velocity on fire suppression system design and performance. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By Andrew F. McKown, Lewis L. Oriard

Advances in explosives engineering are moving forward in several different aspects. These include improvements and new development in explosives products, the application of these products to blasting technologies, and the study of the peripheral effects of the use of explosives, such as ground vibrations and airblast. Topics of special interest in the last several years include new explosives and detonators, cap timing, explosive casting, high-speed photography, perimeter and slope control, air decking and mathematical modeling of blasting processes.

Jan 1, 1988

By Debra W. Struhsacker

Waste characterization plays an essential role in proactive project permitting, design, reclamation, and remediation strategies. Traditional TCLP tests and chemical analyses used in many studies do not provide adequate data to predict the long-term geochemical behavior of the mineralized system. Mineralogic and geologic data are needed to assess the homogeneity of the system, the potential for acid generation or metals leachability, and the amenability of the material to traditional and unconventional closure and reclamation measures. The characterization efforts done from the evaluation stages through final closure can aid in better cost evaluations, more representative sampling, more effective neutralization and waste containment measures, and optimized reclamation designs.

Jan 1, 1995

By A. J. Neale

Much has been published lately about the application of advanced control strategies in the automatic control of autogenous and semi-autogenous grinding circuits. The application of adaptive control algorithms, self-tuning controllers, state estimation, and expert systems has been well documented. While these approaches can be very effective; experience has shown that quite often simply "fixing the fundamentals" can have a significant positive impact on overall grinding circuit performance. This paper will highlight the results of process optimization and process control work by the authors at a variety of autogenous and semi-autogenous installations. A review of one approach for quantifying the mill load/bearing pressure/power relationship is provided. Accurate monitoring of key mill process variables is a necessary prerequisite for both effective process analysis and process control. This paper discusses some of the concerns related to defining steady state operating conditions and the issues related to signal conditioning. The paper concludes with a discussion of an effective application of algorithmic constraint control which incorporates many of these considerations.

Jan 1, 1994

By Charles H. McGuirk

The movement of iron ore, limestone and-coal on the great lakes involves an intricate transportation network between mine, dock, vessel, railroad and consumer. The system requires that stockpiling be performed at certain points in the pipeline because of the seasonal closing of the lakes, traditionally, this has been accomplished at origin and destination with a substantial cost. Impact to both the shipper and consumer, From the time that the raw material is removed from the ground, expeditious handling and movement to final destination is threatened by a series of potential delays. An initial movement from mine or processing plant to the upper lake port must be coordinated between rail equipment and dock facility, As each vessel is loaded, a schedule must be developed which routes the cargo to an unoccupied lower lake port. However, if the vessel is not delayed by unpredictable weather conditions on the lake, the boat may still arrive at a port congested with other vessels awaiting their turn to unload.

Jan 1, 1973

By James R. Arnold, Cindy S. Jones, Michael F. Gleason, John O. Marsden, John G. Mansanti

INTRODUCTION The Chimney Creek Gold Mine (Gold Fields Operating Co. - Chimney Creek) is located 47 miles northeast of Winnemucca, Nevada, at the northern end of the Osgood Mountains. The operation is a wholly owned subsidiary of Gold Fields Mining Corporation, the North American branch of Consolidated Gold Fields PLC, London, England. The plant started up in November, 1987, less than three years after discovery of the orebody and three months ahead of schedule. Ore is mined in an open pit and is processed by combined dump leaching and milling techniques for gold and silver recovery. The mine is set to produce approximately 150.000 ounces of gold and 50,000 ounces of silver per year over a 12 year life at current reserve estimations. The mine was designed and constructed at a cost of $79.3 million with engineering and construction services provided by Davy McKee Corporation, San Ramon, California. Key Gold Fields operating staff were involved in the design of the facility from the start of the project: The Mine Manager, Plant Superintendent, Plant General Foreman, Maintenance General Foreman and Chief Metallurgist were all involved full time on the project within 5 months of the first ore discovery. Emphasis was directed at optimizing operating efficiency and in particular minimizing labor costs in the plant. It was recognized that a high level of instrumentation and control would be required to achieve this. The risk associated with the instrumentation and control systems implemented was to be minimized by using equipment and systems that had been proven in industry while utilizing the most cost effective, state-of-the-art technology available. The reliability of the overall control system was considered to be critical in view of the cost of downtime associated with the gold extraction plant. BRIEF PROCESS DESCRIPTION The dump leaching process treats approximately 1.2 million tons per year of low grade ore at an average grade of 0.035 oz/ton. Run of mine material is dumped on a lined leach pad and weak cyanide solution is applied by drip irrigation. Pregnant solution run off is pumped to carbon columns in the milling plant for gold recovery and the barren solution returned to the dump leach circuit. Average gold recovery is 60%. This process has little instrumentation and control associated with it. The milling operation treats 700,000 tons annually of higher grade ore (0.200 oz/ton initially, dropping to an average of 0.135 oz/ton after first two years). Recovery is directly related to head grade (fixed tail assay effect) and currently averages 96%. A single pass through a jaw crusher reduces run of mine ore to minus 12 inches. The ore is stockpiled and reclaimed by loader for grinding in a two-stage milling circuit consisting of a SAG mill and ball mill, the latter in closed circuit with hydrocyclones. Cyanide and lime are added into the SAG mill to start dissolution of gold as early as possible in the circuit. The ground product leaves the milling circuit at approximately 78% minus 200 mesh and is fed to an unique "double thickener" leaching-recovery circuit. This circuit has been discussed in detail in a paper by J. G. Mansanti et a1 (1). Two thickeners are arranged in counter- current configuration with three leach tanks. Overflow solution from the first thickener is treated by carbon-in-columns (CIC) for gold recovery with 85% of the soluble gold recovered onto this carbon. Underflow slurry from this thickener is pumped to the leach tanks, with a total retention time of 12 hours, and then gravitates to the No. 2 thickener. Overflow solution from the second thickener is used as a wash in the first thickener. Underflow slurry from the second thickener is treated in a carbon-in- pulp (CIP) scavenging circuit to recover the remaining 15% dissolved gold. Gold-loaded carbon from both the dump leach and milling circuits is stripped in batches using the Zadra hot caustic- cyanide elution process. Gold (and silver) is recovered from the hot strip solution by precipitation with zinc dust and the product recovered on Funda pressure filters. The precipitate is retorted to remove any mercury and then smelted into buttons. The buttons (approximately 80% gold, 15% silver) are shipped to an independent refiner in Salt Lake City, Utah, for further treatment.

Jan 1, 1990

By K. N. Han

The adsorption of gold onto activated carbon in iodide solutions was studied. The adsorption rates were determined as a function of temperature, salt concentration and pH, as well as activated carbon concentration. A kinetic model was developed for the adsorption. The adsorption rate was believed to be controlled by a combined mechanism of film diffusion and pore diffusion with the film diffusion having the most significant effect. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1995

By Kerstin Malmqvist

Simulation technique has been used for a feasibility study of a deep exploration project for massive, sulphides in an old mining district, the Skellefte field. An interactive computerized mathematical model of an ore field and a drilling procedure has been constructed. It is possible to represent varying geological structures. The model also takes in consideration economical factors such as drilling costs and ore values. On this model Monte Carlo simulations and probability calculations are done in order to estimate the outcome of different drilling strategies under varying geological assumptions. Under the specific conditions of the well known Skellefte field, it is found to be possible to even calibrate the mathematical model.

Jan 1, 1979

By Ronny J. Sadri

Under contract to the Department of Energy, Fluor Mining & Metals, Inc. and Bonner & Moore Associates developed a group of computer models that can be used to simulate single seam dragline operations. These models have been subsequently modified by Fluor for use in multi-seam dragline mining situations. The single seam model analyzes the digging, spoiling, and walking patterns of draglines to identify possible parameter changes to increase productivity. Parameters such as key-cutting, panel width, digout length, and bench height, etc., are analyzed in this process. The models were tested using data from four operating mines. Field demonstrations were performed to correlate computer optimization results with field data. Productivity was greatly enhanced at one mine site by a change in some of the operating parameters. The multi-seam study has as its objective the development of a broad- based mine planning tool which would be used to identify and quantify the different procedures employed in multi-seam dragline mines to increase their productivity. The major problem identified in multi-seam mining is the sequencing of the different stripping and mining operations. The multi-seam model has the same capabilities as the single seam model. In addition, it models up to four seams with three partings per seam. It allows the operation of several draglines at different levels, and analyzes the effect of ramps, rehandling, and ancillary mining equipment.

Jan 1, 1982

By A. R. Wagner, E. Berkman

The use of high-resolution seismic surveys in coal exploration and mine development is becoming established as a standard technique in the industry. Their most significant contribution is in the effectiveness of reducing the number of core holes needed to understand the complex geological nature of coal by identifying geologic faults and mapping coal seam continuity and relative coal thickness. With these goals in mind, a high-resolution seismic survey was conducted in 1980 in the Wasatch Plateau coalfield of Utah. As a result of the success of this initial survey, numerous additional surveys have been performed over the past six years.. The interpretations of these subsequent surveys have led to the location of faults, fluvial channel sandstones, and coal thickness trends. This paper presents a review of high-resolution seismic technology as applied to coal exploration followed by three case histories, two of which illustrate the utility of the technique related to coal thickness determination and faulting and one that serves as an example of pitfalls in interpretation.

Jan 1, 1987

By S. A. Lolon, J. F. Brune

"INTRODUCTION In underground longwall coal mining, the mined-out areas or gobs frequently contain methane which can form explosive methane-air mixtures. Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of such explosive mixtures, herein referred to as Explosive Gas Zones (EGZs), inside and around the perimeter of bleeder-ventilated longwall gobs (Loane et al., 1975; Lynn et al., 1986; Elkins, et al., 2001; McKinney et al., 2001; Dziurzynski and Wasilewski, 2012; Brune, 2013). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Several factors can induce EGZs outflowing from the gob, but the most common cause is the fluctuating barometric pressure. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Other sudden pressure changes can result from roof falls, failing ventilation controls and fan outages. Any such fluctuation of mine ventilation pressure will disturb the pressure differential between the gob and the surrounding mine workings and may cause EGZs to outgas from the gob. The correlation between major mine explosions and abrupt barometric pressure changes has been studied and confirmed for explosions in coal mining countries including the United States, South Africa, Australia, and Poland (Hosler, 1948; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Hemp, 1994; Wasilewski, 2014; Belle, 2014; and Lolon, 2017). Disastrous mine explosions appear to happen more frequently during stormy weather, which, in the United States, typically occurs during the late fall and winter seasons. ROOT CAUSE AND EFFECT OF GOB BREATHING Gob breathing is the result of the pressure differential between gob internal and external pressures caused by external atmospheric pressure fluctuations that occur naturally as a result of gravitational and thermal forces in the atmosphere (Lindzen and Chapman, 1969). Other major and sudden pressure changes may be caused by fan failures, failures of ventilation controls or roof falls can also cause an unexpected gob breathing. Normal barometric fluctuations occur every day but usually do not pose an explosion risk as they occur gradually so gob pressures have sufficient time to equilibrate. More extreme fluctuations associated with cyclonic weather systems and storms often result in more rapid and larger drops or rises in barometric pressure (Hosler, 1948; Fauconnier, 1992). A study by Lolon (2017) found that the timing of historical mine explosions showed consistency with the occurrence of abrupt and intense barometric variations."

Jan 1, 2018

By W. Robert Rose, Randall Pyper, Carlos Mirabal, Jaime Eguivar

In 1984, work was started to determine the viability of heap leaching silver-containing waste dumps from Cerro Rico near Potosi - Bolivia, at an elevation of 4300 meters (14 100 it.). The result today is an unusual heap leach utilizing fine crushing, grinding, and agglomeration to process 1000 tonnes per day of ore containing 200 g/tonne silver. The unique metallurgical, economic, and political factors will be discussed which led to the decision to build a heap leach rather than a conventional agitation leach plant. Capital and operating costs will be given along with some of the uncommon process design and equipment problems encountered while developing the operation.

Jan 1, 1990

By Y. C. Kim

To generate a most profitable, ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1992

By J. Stachurski, N. A. Abdel-Khalek

Laboratory Potation tests were carried out on six Polish coal samples of different rank. Each coal sample was screened into seven size fractions. The floatability of size- by-size for various size ranges for different samples was investigated as well as for the original samples. The results showed that in flotation of size-by-size, the intermediate sizes varied with the rank of the coal. Entrainment was shown to be an important mechanism in the recovery of fine particles in flotation of the original samples.

Jan 1, 1991

By H. E. Grand

The purpose of this paper is to outline briefly some basic principles of ground- water hydrology that have application in mine hydrology. The development of a mine below the water table pleads for accurate values to answers of hydrology problems. Such problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by isotropic rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where isotropic rocks are not present. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground water used by -hydrologists in the study of behavior of wells should be helpful to mine operators, The work of the Ground Water Branch of the U.S. Geological Survey through its history has been confined largely to the study of ground water as a resource, In view of the increasing number of problems relating to drainage of mines, the Branch started an investigation of mine hydrology in 1945 under the direction of W.T. Stuart, Mr. Stuart and other workers are making detailed studies of specific mine areas. In the present paper an attempt is made to synthesize some facts about ground water into usable form for the typical mine operator. Mining operations that extend below the water table disturb the natural hydrologic regimen, Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine. The behavior of the cone of depression, as it tends to deepen and increase in areal extent when the mine deepens, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised.

Jan 1, 1958

By P. Coleman, J. C. Kerkering, S. Iverson

A fatal accident may result when a dozer is driven over a hidden void in a coal surge pile and the dozer falls into the void, burying and suffocating the dozer operator. This type of accident was analyzed by researchers from the Spokane Research Laboratory of the National Institute for Occupational Safely and Health using inexpensive fault-tree programs that had been developed, for use on a personal computer. Fault-tree analysis is a systematic safety-analysis tool that proceeds deductively from the occurrence of an accident event to the identification of the root causes of that event. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between the basic events as well as the intermediate events leading up to the accident. A sensitivity analysis on assigned probabilities showed which events had the greatest influence on dozer burial in a coal surge pile. Operational guidelines and engineering controls are suggested to decrease the probability of a burial event.

Jan 1, 2002

By C. C. Bailie

This paper will be concerned with those mineable coal measures at depths necessitating deep mine operations in the range of 200 feet to 800 feet in depth. The area is generally classified as the Southern Illinois Field but more specifically includes that part of the state south of a line extending from St. Louis, Missouri on the west to Vincennes, Indiana, on the east. This embraces an area which presently includes a total of 38 shipping mines and 5 local or truck mines. Of these shipping mines, 22 are deep (shaft or slope) mines and the remaining 16 are strips. The average annual production of the shipping mines is around 29 million tons. The presently classified mineable reserves of the area are estimated at around 70 billion tons.

Jan 1, 1964

By D. E. Ranta, Neil D. O’Donnell, Thad B. Ostrowski

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project's inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an orebody block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1992

By P. K. Chatterjee

Before coal can be extracted from surface or underground mines, approval must be obtained from state and federal authorities. Permitting is the application process through which such approval is sought. The application includes en environmental impact statement Which focuses on Such topics as subsidence, toxicity of acid mine drainage, pollution levels of rivers and streams, post mining reclamation, and the effect on the hydrological balance of the area. The permitting procedure is extremely time and labor intensive, and requires extensive interdisciplinary knowledge. This paper examines a LISP based permitting procedure which will help to reduce the time taken to prepare and review a permit application.

Jan 1, 1986

By S. Mathur

Oxide particles are commonly used as fillers in plastics, paper, rubber etc. (particulate composites). The successful fabrication of such composites is dependent upon the adhesive strength of the filler particles to the matrix. The compatibility of the matrix and the filler particles is generally enhanced by adsorption of surface modifiers such as surfactants and polymers at the particle-matrix interface. In order to develop a scientific basis for selection of appropriate modifiers it is necessary to understand their adsorption mechanism(s). Specifically, adsorption of polymeric additives is attributed to a combination of chemical and electrostatic interactions, hydrogen bonding and van der Waals forces. Hydrogen bonding has been suggested to be the primary adsorption mechanism for non-ionic polymers. However, a literature survey of Poly(ethylene oxide)(PEO)-oxide system suggested PEO, a non-ionic polymer, to be substrate specific. A systematic study was undertaken to investigate the adsorption mechanism(s) of a PEO on oxide particles. It was determined that strong Bronsted acid sites on the surface interact with the ether oxygen, a Lewis base, of PEO to induce adsorption. In this work characterization of PEO binding sites on oxides is reported and the mechanism(s) of PEO adsorption discussed.

Jan 1, 1997