Search Documents

By Z. Lin, M. Isac, R. I. L. Guthrie

The kinetic and thermodynamic efficiencies of chromium recovery from the slag in an AOD process during the slag de-oxidation period with ferrosilicon is a complex process affected by slag basicity, temperature, the dissolution kinetics of the reducing agents, and intermixing of the slag/metal/alloy addition phases within the vessel. The present work focused on a study and simulation of the fluid dynamics and mixing behaviour of ferrosilicon additions in the AOD process for the production of stainless steel. In order to visualize the mixing behaviour, a two dimensional slice model of an AOD vessel was first built and filled with ZnCl2solution and then covered with silicone oil in order to represent the bulk liquid steel and slag phases, respectively. The injection of argon/oxygen process gases was simulated using air or helium. Particle trajectories and intermixing of the phases was monitored with a high-speed camera. To simulate the 75FeSi additions, glass spheres were used. A three-dimensional version of the AOD model was then constructed in order to confirm the adequacy of the slice model. Similar particle mixing behaviour was observed. Both models demonstrated that the ascending gas/liquid plume created two asymmetric mixing zones: a smaller rapidly re-circulating mixing zone adjacent to the side-wall locating the tuyere(s), and a larger mixing zone in the main part of the vessel. The process efficiency during the reduction period is governed by the thermal behaviour of ferroalloy as well as the mixing efficiency in the main large mixing zone. To enhance the recovery efficiency for chromium, small Fe-Si particles are suggested, given their wide distribution within the slag phase, and their large interfacial areas and rapid melting times for Cr2O3reduction from the slag. Keywords; modelling, ferrosilicon, chromium oxidation, AOD steelmaking.

Jan 1, 2004

Publications on hard rock tunnel support design in the South African mining industry have originated primarily from the goldmines during the past 50 years. Little has been published to date on the platinum and chrome mines of the Bushveld Complex. This paper covers the search for a suitable design methodology for off-reef tunnels at Impala Platinum Mine, situated on the Western Lobe of the Bushveld Complex. The fall of ground accident statistics for off-reef excavations of the mine are presented and the available rock mass quality evaluation systems are reviewed. The Q-Tunnelling Quality Index (or Q-Index) is selected because it assesses the important driving factors behind falls of ground at Impala. Two off-reef excavations are evaluated using the Q-Index, and it is shown that minor modifications are required for implementation at Impala. It will take some time before support design throughout the mine is based on the outcome of proper geotechnical investigations based on the Q-Index. Widespread implementation of such support designs should help to solve the fall of ground problem in off-reef excavations while at the same time reducing support costs.

Jan 1, 2002

By C. F. Vos, J. D. Miller, J. C. Davidtz

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate(DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromite rejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2006

By J. P. W. Bennie, A. de Jong, G. M. Denton

Mintek together with Middelburg Steel & Alloys, developed the DC arc furnace process for the production of ferroalloys with the expressed objective of smelting ore fines (<1mm) without the need for agglomeration. In the case of ferrochrome production, the DC arc furnace, being a semi-open bath operation, loses radiant energy directly from the bath to the furnace roof and sidewalls above the melt. This energy loss is reflected in a higher electrical energy usage per ton of alloy than for a submerged-arc operation smelting lumpy ores or sintered pellets. The difference increases still further when pre-heated sintered pellet feed is used in a submerged-arc operation. This shortcoming of the DC arc furnace can however be overcome by preheating the feed to the furnace in a fluidized bed or flash reactor fuelled by cold furnace off-gas. In addition to fluidization and preheating testwork, various preheating flowsheets with associated mass and energy balances have been developed and compared from a techno-economic viewpoint. The three major advantages identified were: a) fluidized beds can preheat ores and fluxes up to 950°C without sticking and defluidizing, b) the open bath DC arc furnace does not require expensive coke or char to maintain the burden porosity and, c) the capital cost associated with the milling, pelletising and sintering plant falls away since ore fines are used directly.

Jan 1, 2004

By G. Westcott

Impala Platinum, the second largest platinum producer in the world, is embarking on a major expansion strategy to increase its platinum output from 1.95 moz to 2.8 moz by the year 2008. The smelter complex, situated in Rustenburg, will undergo substantial modifications, and will require a solution to the capture and treatment of the smelter off-gases and dust produced during smelting and converting operations. One of the solutions explored was an integrated approach, where all the off-gases from both the primary smelting electric furnaces and the converter operations are routed to a large central gas cleaning and double catalysis, double absorption acid plant. In-line sulphur burning, utilizing a highly flexible LURO1spin cup burner with a turn down ratio of 50%, ensures that the acid plant operates independently of operating conditions at the smelter complex.

Jan 1, 2007

By A. Wedepohl

Selective leaching of phases in charge chrome is used in a variety of industrial processes for the production of chromium chemicals. A mineralogical study was made of a range of local charge chrome samples, at various stages of leaching in sulphuric acid (20g/l at 90°C), using mainly a scanning electron microscope (SEM) together with an energy-dispersive spectroscopy analyzer (EDS), and X-ray diffraction techniques. It was found that the leaching behaviour of the different types of charge chrome depends largely on the nature of the secondary phases, which in turn depends upon whether the silicon content is above or below 4 per cent by mass. The leaching behaviour of high-chromium ferrite is anomalous, and it is postulated that the process is analogous to the corrosion of brass by dezincification. Keywords: charge chrome leaching, scanning electron microscope

Jan 1, 2000

By M. A. Amarante

Beneficiation studies were conducted on a Portuguese feldspar ore, in order to obtain final products capable of being used in the ceramic industry. A simple scrubbing operation is enough to break the lumps in the feed. The ore deposit contains ca 35 x 106tonnesfrom which, by screening, three main products could be obtained. This paper focuses on the beneficiation of the 500/74 µm fraction, which constitutes about 27% of the ore, assaying 9.42% Al2O3,equivalent to approximately ca 46% feldspar, with a mean iron content of 0.29% iron oxides. Magnetic separation and froth flotation testwork was carried out, in order to decrease the iron contamination and increase the feldspar content. Magnetic separation alone decreased the iron content of the feed to values between 0.04 and 0.08% iron oxides with an average yield greater than 90%. Flotation with HF, provided a feldspar recovery of 45?46% with a concentrate assaying 17.6% Al2O3. The use of H2SO4, gave a recovery of 35?36% of feldspar concentrate, assaying 16.1% Al2O3. However, economic and environmental advantages of using sulphuric acid may compensate for the lower mass recovery. The iron content of0.12% iron oxides in these concentrates, could be reduced to 0.04?0.05%, by further magnetic separation.

Jan 1, 1997

By D. Zhou, T. Hamano, Tsukihashi. F., W. -G. Seo

The thermodynamic properties for the CaO-CaF2and CaO-BaO systems were calculated by molecular dynamics (MD) simulation using Born-Mayer-Huggins type pair potential. The parameters of interatomic potential were obtained by fitting the thermodynamics properties of CaO, CaF2and BaO with the experimental data. The phase diagrams for the CaO-CaF2 and CaO-BaO systems were calculated by the thermodynamic properties obtained by MD simulation. The eutectic composition and temperature of the CaO-CaF2system calculated by MD simulation were about 28 mole per cent CaO and 1575K, respectively. The calculated eutectic point agrees very well with experimental data, which are about 22 mole per cent CaO and 1633K, respectively. Keywords: molecular dynamics simulation, thermodynamics, phase diagram, calcium oxide, calcium fluoride, barium oxide.

Jan 1, 2004

By M. Sanchez, C. Morales, J. Palacios

The slag produced in the Peirce Smith converters at the Ilo smelter of Southern Peru Copper Corporation has shown a wide range of magnetite content, which introduces an additional problem in the smelting units due to materials? recirculation. However, the operation data analysis and the application of thermodynamic concepts have made it possible to produce slag with magnetite content between 18 and 20%. The results have suggested that matte grade enhances magnetite formation while silica controls its precipitation, and they are also influenced by the increasing temperature of the slag. Thus, in order to obtain the required magnetite content in the slag, matte grade is gradually enriched in equilibrium with slag containing from 25 to 32% silica.

Jan 1, 2004

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

By H. Kotzé

Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and mineral separation plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2slag and 145 kt/a of pig iron.

Jan 1, 2006

By A. J. Van Der Merwe, N. A. Barcza, M. Boyes, N. R. Clarke

Oriel Resources has with the support of SRK (Cardiff) and DRA and Mintek (South Africa) carried our a Definitive Feasibility Study (DFS) to recover high grade chrome ore from its Voskhod deposit very close to Chromtau that is near to Aktobe in Kazakhstan. Voskhod is a large podiform ore body that contains nearly 20million tons of chromite grading about 48% Cr2O3 and with a Cr/Fe ratio of over 3/1. Selected bore hole core samples were obtained from the confirmation drilling programme during the DFS phase of the project in 2005 for pilot plant test work to design the mineral beneficiation plant. The chrome ore is characterised by four main types, namely high grade lumpy and chip sized ore, high-grade fine ore, lower grade (subordinate) lumpy ore and lower grade fine ore. Gravity separation tests carried out by Mintek showed that the large density difference between the high grade (at over 3.7t/m3) and lower grade ore (at less than 2.97t/m3 ) should ensure very good separation in the DMS drum and DMS cyclone stages resulting in high recoveries of Cr2O3 - rich chromite ore products. Very high chrome ore grades of up to 64% Cr2O3 and Cr/Fe ratios of 4 to 1 were obtained at an 80% mass yield from selected samples of lumpy and chip ore size fractions. The overall predicted recovery from the design work on the mine and plant is expected to be closer to about 70% of the ROM (Run of Mine) feed. DRA has completed the design of the mineral processing plant to recover about 900 kt/a of chrome ore from the 1.3 Mt/a of ROM feed. The plant has been sized to handle up to 1.5 Mt/a and will also be able to address the variability in ore feed as different regions in the deposit are mined. The lumpy high-grade product and the chips size fraction is expected to grade around 48% Cr2O3 and the fine concentrate between 56 and 58%Cr2O3 The ratio of products is expected to be about 70, 15 and 15 percent respectively but will vary to some extent during the expected 20 year life of the mining operation based on including the associated adjacent Karaagash deposit together with the Voskhod deposit. The prediction of the product split from the processing plant depends on many factors such as the geology, mineralogy, mining, handling and metallurgical processing. An overall process flow model has been developed that covers the ROM ore, the various types of chrome ore feed to the mineral beneficiation plant, the projected products and the subsequent smelting of the chromite ores to produce High Carbon Ferrochromium. The model allows the optimisation of the quality of the chrome ore in terms of Cr2O3 content, Cr/Fe ratio and recovery to be studied. This information can also be evaluated in terms of the economic requirements for smelting High Carbon Ferrochromium (HCFeCr) at a given location. Oriel is planning to supply chrome ore to Ferrochrome plants mostly in China and Russia. The use of the model will assist to maximise the value of the Voskhod project to its owners and also assist the users of the chrome ore in selecting the appropriate supply quality to meet their needs for a given smelter operation. The smelting of high grade Voskhod ore requires a limited addition of about 5 to 7% quartz to flux the MgO and Al2O3 and about 25% coke as a reducing agent to produce an alloy containing from about 65 to 74%chromium depending on the Cr/Fe ratio.

Jan 1, 2007

By M Lipalile, A B. Tunono, A W. Naismith

Konkola No 3 shaft experienced severe mining induced stress and time related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of 160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By J. M. Font, R. G. Reddy

Jan 1, 2004

By M. A. Hermanus

This paper examines the occupational health and safety performance (OHS) of the South African mining sector against the backdrop of changes in the composition of the sector, international trends in OHS performance, and the agreement on OHS milestones and targets by mining stakeholders at the Mine Health and Safety Summit of 2003. Although OHS performance has improved, progress is slow and there is need for significant rather than incremental change if the targets are to be realized. Since 2003, fatalities and injuries are 20?25% short of annual milestones and not all commodities show consistent improvement. Statistics on occupational health impacts are unavailable, but noise and respirable dust levels are known to be high in mines, with much work lying ahead to address exposures at source. Trends in regulating and addressing OHS hazards are discussed with reference to the notion of ?systems-thinking? and the targets. Efforts to improve OHS and to respond to changes in the sector are constrained by a lack of training and consistency in risk management, guidance for junior, small and artisanal miners, and holistic approaches to risk. For example, treating risk holistically would involve taking proper account of contractors and women in the workplace, and attending to human factors and ergonomics.

Jan 1, 2007

By W. J. Errington

The Isasmelt process was developed at Mount Isa Mines Limited in Queensland, Australia in collaboration with CSIRO, the Australian Government research organisation. Originally developed for primary lead smelting, culminating in the construction of a 60,000 tonnes per annum lead smelter at Mount Isa, this technology now also provides a major part of the current 200,000 tonnes per annum copper smelting capacity at Mount Isa. A programme is now in place to expand copper production to 250,000 tonnes per annum. The technology has also been applied to secondary lead smelting at Britannia Refined Metals, a MIM subsidiary company, where a 30,000 tonnes per annum lead plant based on battery scrap feed has been operating since 1991. Mount Isa Mines Limited decided to license the technology in1988, and copper smelting plants utilising Isasmelt technology are now operated by Cyprus Miami Mining Corporation in the USA and by Sterlite Industries in India. In addition, the technology was adopted by AGIP for smelting copper/nickel concentrates in Australia. Union Miniere are currently constructing an Isasmelt furnace to smelt and convert copper-containing materials at their plant at Hoboken in Belgium. This paper discusses these developments and also some likely future developments which include the application of the technology for continuous copper and nickel converting and applications in the treatment of zinc-containing residues.

Jan 1, 1997

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004