Search Documents

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By O. Nyandoro, K. Khoza-Shangase, M. Madahana, N. Moroe

"Occupational noise-induced hearing loss (ONIHL) is classified as the leading work-related disability in the mining industry. ONIHL has a negative impact, on not only the health and occupational productivity of affected individuals, but arguably also on the country’s mining industry and economy. Hearing conservation programmes (HCPs) are an effective strategy in the management of ONIHL. However, current literature indicates that HCPs are not achieving the anticipated and desired outcomes in the South African mining sector despite the efforts focused on the management of ONIHL. Therefore, the purpose of this study is to propose the use of a feedback-based noise monitoring model as a tool for monitoring and managing ONIHL in the South Africa’s mining sector. This model is a basic static feedback model with practical applications such as estimating, monitoring. and providing quantitative information to aid miners, mining administrators, and policy-makers in decision-making around HCPs. Additionally, the model could form part of an early intervention and management strategy for ONIHL in the workplace. The strength of this model, although currently static, is that it encompasses all the pillars of HCPs and takes into account the policies concerned with the management of ONIHL in the mining sector. IntroductionHazardous noise levels (above 85 dBA) in the workplace place exposed employees at risk of developing a disabling occupational noise-induced hearing loss (ONIHL). ONIHL is the ‘partial or complete hearing loss in one or both ears as a result of one’s employment’ (Nandi and Dhatrak, 2008, p. 1). This type of hearing loss develops gradually as a result of being exposed to continuous or intermittent high levels of noise over a long period of time (McBride, 2004; Patel et al., 2010; Rappaport and Provencal, 2001). A hearing threshold below 40 dBs is classified as a disabling hearing loss (Yadav et al., 2015), resulting in a hidden condition that does not readily manifest itself (Tye-Murray, 2009, p. 3). Dugan (2003) describes disabling hearing loss as the ‘most prevalent, least recognized and least understood physical disability’, while Copley and Frederichs (2010) and Hermanus (2007) argue that permanent disabling hearing loss is a major contributor to the global burden of disease on individuals, families, communities, and countries."

Jul 1, 2019

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the openstopes. Little work has been done in the past to determine pillar strength and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to oversize pillars with consequential loss of ore or undersize pillars resulting in potential collapses or pillar bursts. This paper describes a back-analysis of pillar failures at Impala Platinum, just north of Rustenburg, and provides insights into pillar behaviour. Strength formulae are presented for Merensky Reef pillars at Impala. These formulae may be used cautiously on other platinum mines with similar geotechnical and geomechanical conditions.

Jan 1, 2008

By I. Ocak

The modulus of elasticity of rock material (Ei) is an important rock property that is used as an input parameter in the design stage of engineering projects such as dam and tunnel constructions, mining excavations, and so forth. However, determination of the modulus of elasticity is sometimes difficult to obtain by laboratory tests because high-quality cores are required. For this reason, empirical methods for predicting the modulus of elasticity of rock material have been popular research topics in recently published literature. In this study, the relationships between the uniaxial compressive strength (UCS), unit weight (?) and modulus of elasticity for different types of rocks were analysed by using 177 data obtained from laboratory tests carried out on cores obtained from drill holes within the area of the Kadiköy-Kartal Metro line (Istanbul, Turkey). Keywords: Kadikoy?Kartal Metro, uniaxial compressive strength, unit weight, estimating the modulus of elasticity.

Jan 1, 2008

By R. L. Castro

The extraction of ore in panel caving operations also involves the coextraction of non-economic material, known as dilution. Forecasting, avoiding, and understanding the mechanics of dilution is critical to longterm planning. The models of dilution that are currently in use in panel caving operations are those by Laubscher (1994), who postulated that dilution is due to gravitational flow and depends on the height of interaction, the column height, and the draw uniformity. This paper presents a back-analysis of extraction and dilution behaviour at Codelco?s El Salvador and Andina Divisions, which use panel caving as a mining method. This analysis was conducted in order to review the existent dilution entry mechanisms and calculation methods. Three sources of dilution were identified. The first source is ?gravitational dilution?, which is due to gravitational flow and mixing as dilution migrates by gravity from a sector located above the panel under analysis. The second source of dilution is ?caving dilution?, which occurs when an air gap is formed in a large area and a sudden propagation of a hang-up occurs, inducing early ingress of waste into the production level from a level above. The third mode observed is ?lateral dilution?, which occurs when the panel is located next to an exhausted sector and the broken material enters the draw column early during draw. In the last two cases, dilution could migrate large distances horizontally. The mine data indicated that draw and caving strategy are key for long-term planning of large panel caves.

Jan 1, 2014

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By J. H. Maritz, Uludag. S.

"*Paper written on project work carried out in partial fulfilment of B.Eng(Mining Engineering) degreeAfriTin Mining Limited plans to reopen the Uis tin mine in Namibia and establish a pilot processing plant for phase 1 of the Uis tin project, which is scheduled to commence in the last quarter of 2018 . A mining plan is required for phase 1 to supply the new pilot processing plant with 500 kt of run-of-mine ore per annum, for a period of 5 years. New geological mapping and three-dimensional modelling of the mining area were utilized to identify the most optimal mining locations that require low initial waste stripping. An open-pit mining method was selected to target the surface outcrops of the pegmatite orebodies. The mine design criteria were determined and used as input to generate the mine design by utilizing professional engineering software. The mine design was optimized and an overall stripping ratio of 0.81 was achieved. A 5-year production schedule was developed for the mine design according to quarterly periods of three months. A fixed production target of 125 kt of ore was assigned to the quarterly periods, and a ramp-up production target of 65 kt of ore was assigned for the first period. The mobile mining equipment requirements were calculated, and recommendations were made for implementing the 5-year mining plan. IntroductionAfriTin Mining Limited is the owner of the Uis tin project in Namibia and plans to reopen the Uis tin mine, which is located near the town of Uis, approximately 164 km north of Swakopmund. The Uis tin mine was owned and operated by Imkor Tin, a subsidiary of Iscor South Africa. Mining commenced in 1958, and the operation was closed in 1991. Steffen Robertson & Kirsten (SRK) defined the life of mine (LOM) plan for the historical Uis mine in 1989. The SRK report estimated the historical resources and reserves, which consisted of sixteen cassiterite-bearing pegmatite orebodies. SRK developed the most economical pit designs to provide the highest average tin grade at the lowest practical waste stripping ratio. Exploration data from the SRK report of 1989 was used extensively throughout this study, since no new exploration drilling has been conducted. The pegmatites are present as large, subvertical and outcropping veins up to 100 m in thickness. Once phase 1 is operational, mining will be conducted using conventional open pit mining methods. Initial production will be from exposed pegmatite veins in the old mine workings. AfriTin plans to establish a pilot processing plant by the end of 2018 to beneficiate run-of-mine ore at a rate of 500 kt per annum."

Jul 1, 2019

By Phillip M. Dight

A number of impending and actual pit wall failures have been observed and documented which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

By S. N. Opperman

Testwork at Goedehoop Colliery showed that fine coal, essentially?150 microns can be successfully beneficiated using froth flotation. Both conventional and column flotation were tested. It was found that the traditional stirred tank type of flotation machines used in conventional flotation produced the best recovery of fine coal. After extensive testwork it was decided to develop a flotation machine on Goedehoop Colliery that would combine stirred tank and quiescent column technology. It was thought that this design would give the best combination of recovery and selectivity. The Multicell was developed and is producing results acceptable for Witbank coal flotation. Keywords: Multicell, Witbank coal flotation, froth, stirred tank, quiescent column.

Jan 1, 2002

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

By W. E. Lee

Penetration and dissolution mechanisms are reviewed for predominantly single-phase oxide, two phase oxide and oxide-carbon composite refractories by liquid silicate slags. Theoretical models of these processes, as well as static (sessile drop, dipping and crucible) and dynamic (rotating finger and rotary slag) experimental tests, along with their practical limitations are considered. Direct (congruent or homogeneous) attack is controlled by the reaction rate at the slag-refractory interface or the rate of diffusive transport of species to it through the slag leading to active corrosion. Indirect (incongruent or heterogeneous) attack is controlled by diffusive transport through the slag or through a new solid phase, which forms at the original slag-refractory interface. This may lead to passive corrosion. Examples of direct and indirect attack in a range of refractory/slag systems are described highlighting the critical influence of the composition and hence viscosity of the local liquid slag adjacent the solid refractory. Penetration and corrosion can be controlled either through the local slag composition via the refractory or the bulk slag or by microstructural control of the refractory by e.g. internal generation of dense layers or external deposition/generation of passive coatings, so-called in situ refractories.

Jan 1, 2004

By C. N. Harman

Steel is the most versatile material which has made the progress in every aspect on this earth possible. There are hundreds of varieties of steel because for each application it has to be made with specific properties to get the most optimum usage. It is well known that the basic constituent of steel is iron. But it is the proportion of other elements in it, which give each type of steel certain specific properties. These elements are added in liquid iron inform of Ferro alloys to get the desired composition and properties. Thus, Ferro alloys are important additives in the production of steel. It can be said that no steel can be made without use of one or more of the several Ferro alloys. They form the backbone of steel. Thus, the Ferro alloys industry is vitally linked for its growth and development to that of the steel industry. Ferro alloys industry in India has never been globally competitive, despite its rich ore deposits and low-cost manpower, essentially due to a) Insufficient availability and high cost of electric power b) Increasing ores and reductants cost c) Non-availability of low ash, low phos. coking coal in the country for the production of desired coke with low ash, and low phos. contents, making import of such coke at a high cost imperative d) High-cost and insufficient infrastructural facilities (both road and rail) for rapid transportation of ore from mines to plants e)Stiff competition from producers and exporters of Ferro alloys in other countries like South Africa, Kazakhstan, China, Russia, Australia etc. due to global trade agreement which has made drastic reduction in customs duty on imports necessary. f) Wide fluctuations in the International price of Ferro alloys depending on demand versus supply. To over come these challenges plus adhering to stringent pollution control norms innovations are inevitable in the process technology, and plant equipment design, along with frequent changes in product mix, to be more cost-effective. An attempt is made in this paper to address the innovations that took place in the past and those that further need to be made, considering the future of this industry.

Jan 1, 2007

By J. Härkki, R. Hiltunen

The Akanvaara intrusion (surface area 50-55 km2) in Savukoski, Northern Finland, hosts 23 distinct monocumulate layers of small euhedral chromite crystals enclosed in a silicate matrix. These chromitite layers have been divided into four groups; UC (upper chromitite), ULC (uppermost lower chromitite) LC (lower chromitite) and LLC (lowermost lower chromitite). The driving force for investigating the Akanvaara chromites and their reduction behaviour originated from their very low MgO content and relatively low Al2O3 content, giving them a unique quality which based on thermodynamics should facilitate the reduction. Another interesting feature is the high amount of V2O3 present especially in the upper chromitite. The chromites included in this study are from the UC and ULC layers (24.9 and 22.7 per cent Cr2O3 respectively). To obtain a better understanding of the reduction behaviour of Akanvaara samples in comparison to MgO-bearing chromitites, Kemi chromite from the ferrochrome works in Tornio, Finland, was included in the study as a reference sample. The reduction experiments were isothermal in a temperature range of 1000-1400°C in CO atmosphere. Experiments were also conducted with coke addition in pellets and briquettes in CO/Ar/H2 atmospheres. The results of the reduction experiments complemented with microanalytical research indicate that the Akanvaara chromites do reduce to a higher degree than the Kemi chromite. Although the aim was to characterize the mechanisms of reduction focusing on gas-solid reactions, the nature and amount of the gangue minerals was such that a considerable amount of slag phase was formed, which affected the reduction mechanisms extensively. The structural features together with low MgO and high FeO content in both Akanvaara chromites are important factors resulting in better reducibility than in the Kemi chromite.

Jan 1, 2004

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 22nd August, 1973. Dr J. P. Hugo (President) was in the Chair. There were also present 64 Fellows, 20 Members, 5 Associates, 3 Students, and 34 Visitors, making a total of 126. The President declared the meeting open at 4.05 p.m. OBITUARIES The President: It is my sad duty to announce the death of the following members of the Institute C. Boocock, R. J. G. Moore, M. P. Pearse, and A. I. Sussman, all Fellows, and W. T. Dalling, a Life Member. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. MINUTES Die President: Item twee op die agenda is die bekragtiging van die notules van die jongste Algemene Vergadering van die Instituut. Daar die notules in die Augustus uitgawe van die Joernaal gepubliseer is, vra ek u toestemming dat dit as sulks bekragtig word. Toestemming verleen. WELCOME TO VISITORS The President: It is my very great pleasure to welcome all the distinguished guests who have honoured us with their presence this afternoon; in particular, a hearty word of welcome to the Honorary President of the Institute, Mr Plumbridge, the President of the Chamber of Mines. You are doubly welcome here, sir, and we thank you for your presence. Also to that old member and stalwart, the Honorary Vice-President of the Institute, Mr Tommy Gibbs, the Government Mining Engineer-you're very welcome, Mr Gibbs. Then, we are particularly privileged this afternoon to have an Honorary Member with us, the Minister of Mines for Rhodesia, Mr Dillon. You will recall that he honoured us with his company last year. Mr Dillon, we are very appreciative and hope that this is now a standing arrangement. We are also honoured by the presence of some thirteen Presidents, Vice-Presidents, or Chairmen of our sister scientific and technical organizations. I shall rapidly read their names, but they must all feel assured that they are very welcome here today. Firstly, one of our own Past Presidents and members, Mr Geoff Goode in his capacity as President of the Associated Scientific and Technical Societies of South Africa; Mr L. R. Robinson, President of the South African Institution of Mechanical Engineers, and Mrs Robinson; Mr G. Goedhals, President of the South African Institute of Electrical Engineers ; Dr Antrobus, President of the Geological Society of South Africa, and Mrs Antrobus; Mr T. V. Dean, Vice-President of the Institute of Land Surveyors of the Transvaal, and Mrs Dean; Mr R. M. Stroh, President of the Mine Ventilation Society of South Africa; Mr Ken Steele, President of the Association of Mine Managers, and Mrs Steele; Mr Mike Gericke, President of the South African Council for Professional Engineers; Mr R. G. Matthews, President of the Institute of Mine Surveyors of South Africa; Mr P. H. Pettifor, President of the Institute of Production Engineers, London, and Mrs Pettifor ; Dr Nico Stutterheim, Chairman of the South African Institute of Chemical Engineers, and Mrs Stutterheim; Professor F. A. van Duuren, Chairman of the Engineers' Liaison Committee in Pretoria; also, I haven't spotted him but I trust he is here-Mr Alex Bain, who is Chairman of this Institute's Witbank/Middelburg Branch. To one and all, ladies and gentlemen, a hearty word of welcome. Not last on our list, a word of welcome to Mr Eric Boden, the Manager of A.S. and T.S. We also have with us I trust, Dr Deist, and his good lady-Dr Deist will be figuring in our proceedings later this afternoon. Also Mr Barcza and Mrs Barcza. Mr Bareza, a former President of the Institute, also has a task to perform. Then, I hope two of our student prize winners are here-Mr Beetge and Mr Painting. Then we also have Mr Roberts, who is welcome in his capacity as co-author with Dr Deist. Then, last of all, a hearty word of welcome to Dr Helen Glen (I am not sure whether she has arrived yet, but she is certainly due to come)-the new Honorary Editor of the Institute's Journal. MEMBERSHIP The President: I have pleasure in announcing that, their names having been published in accordance with By-law 5.2.2, the following have been elected by Council to membership in the following grades Fellows: W. G. Jayes and F. K. Wright Members: D. W. Penman, A. W. Bryson, and D. L. Gibbs Graduates: R. J. Adey, J. P. Bond, R. C. Dunne, G. M. Entwhistle, J. M. Rendu, J. P. S. Turner, and A. P. van Jaarsveld Associates: A. Ellis, B. R. Hambly, A. J. Johansen, and G. W. Tregoning

Jan 10, 1973

Paper written on project work carried out in partial fulfilment of B.Sc. Eng. (Extractive Metallurgy)degree The concepts behind support vector machines are very interesting both in theory and in practice, as they are based on a universal constructive learning procedure derived from the statistical learning theory developed by Vapnik. In this paper, their application to time series modelling is considered by means of simulated data from an autocatalytic reactor. In particular, reconstruction methods from non-linear dynamics are used to define a state space model for the process. Multivariate embedding techniques are compared to scalar embedding with respect to modelling. Keywords: System identification, Support vector machines, Multilayer perceptrons, Non-linear dynamics

Jan 1, 2003

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives involve several potential pitfalls. These are outlined in the present paper.It was found that coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate. For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition. Significant errors could be incurred if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen).For elemental analysis determination, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range. For representation of sulphur in coal, one should avoid doublecounting due to SO3 in the ash analysis.Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2.However, use of some of these species without considering the experimentally determined gross CV leads to significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy. Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than these four, provided the enthalpy is corrected.It is recommended that an ‘enthalpy correction value’ be incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to carbon being present in a form other than graphite should be used, as that would imply double-counting some effects."

Jan 1, 2015

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By G. G. le Roux

The purpose of the investigation was to assess various options for increasing the efficiency of the conveyor belt transporting system used at 4 Belt Shaft at Lonmin?s Marikana operations. The reason for the investigation was to prevent the occurrence of a ?bottleneck? at the main ore passes delivering ore to the conveyor belt system, thus creating more fluent operational conditions. The options assessed for increasing the efficiency of the conveyor belt transporting system were: ?Variation of the conveyor speed ?Concurrent tipping from two ore passes on the belt ?Increase the available drive unit power ?Increasing the feed rate from vibratory feeders ?Change in belt width/belt specifications The report shows that the most preferable option to the current situation at 4 Belt, Lonmin, would be the option of concurrent tipping from two ore passes to the belt.

Jan 1, 2008

By C. G. Anderson

"As demand for copper and precious metals continues to grow, the need to develop new supplies increases. In the imminent future, the new large global ore bodies are more complex, with enargite, tennantite and tetrahedrite as the abundant contained mineralogy. These resources also contain considerable gold and silver. As such, direct treatment by conventional smelting is prohibitive due to the potential environmental impacts and copper quality issues. This paper outlines the effective application and associated economics of industrially proven Alkaline Sulfide Leaching (ASL) hydrometallurgical technology to an enargite concentrate for selective removal and recovery of arsenic, antimony, gold and silver, leaving a clean high-grade copper concentrate. The fundamentals behind the technology are described, along with those of hydrometallurgical arsenic fixation and stabilization. Flowsheets and unit operations are elucidated, along with an in-depth economic analysis. INTRODUCTION Hydrometallurgical methods can be employed for treatment of gold-, arsenic-, antimony-, tin- and mercury-containing materials, concentrates and ores, as well as complex ones containing any number of metals (Conner & Anderson, 2013). The alkaline sulfide leaching (ASL) system is one of these. It is essentially a mixture of sodium sulfide and sodium hydroxide with other meta-stable alkaline species as required. This is a unique hydrometallurgical system beause it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic, tellurium, silver and mercury (Anderson, 2000, 2001a, 2001b, 2002, 2003, 2012, 2014; Anderson & Twidwell, 2008a, 2008b, 2010; Anderson et al., 2004, 2005; Glazkov & Tseft, 1961; Gnatyshenko & Polyvyanni, 1961; Nadkarni et al., 1975; Nadkarni & Kusik, 1988; Polyvyanni, 1963). Worldwide, ASL technology has been employed industrially in the former CIS, China and the United States for the production of antimony (Anderson et al., 1992, 1994; Anderson & Krys, 1993; Holmes, 1944; Kaloc, 1967; Nordwick & Anderson, 1993; van Stein, 1971)."

Jan 1, 2015