Search Documents

By B. N. Soutar

The design and operation of a double- V compartment vertical-flow settler by B. N. SOUTAR, B.Sc. (Mech. Eng.) Wits. (Visitor) This paper describes the development of a vertical-flow settler for underground pumping installations in the mines of Gold Fields of South Africa Ltd. The recommended settler employs the principle of 'dynamic filtration': the solids that are in suspension in mine water are filtered through a stable horizontal bed of flocculated particles, a technique that was established in about 1958.

Jan 3, 1977

By M. C. Harris

Float-sink analysis has wide application in the coal laboratory. This paper evaluates the established methods used for the float-sink analysis of fine coal, and then describes a new method and apparatus that can be used for material down to a few micrometres in size. The method is rapid and accurate, and requires only a small amount of sample. The results presented show close agreement with the float-sink analyses obtained by the more classical technique using separating columns. The new centrifugal method reduces the time required for the analysis by a factor of ten.

Jan 1, 1986

By M. J. Nicol, G. Cromberge

An account is given of the development of a relatively simple model that describes the kinetics of the absorption of gold cyanide on activated carbon. The model is based on the treatment of the carbon solution interface as a homogeneous boundary across which gold is transported at a rate determined by the rate of mass transport to and from the interface. Rate equations derived from this model describe the results of various kinetic experiments under continuous or batch conditions in the laboratory and on operating pilot and full-scale plants.

Jan 1, 1983

By A. A. Hazell

Mine management by objectives By A. A. HAZELL The author discusses the objective areas of mine management. Setting objectives is seen to be a conscious process which starts at the highest level of management. This enables clear objectives to be set at each lower management level. The methods of setting objectives in the areas of stope production, productivity and manager performance are set out in detail. In the area of manager performance emphasis must be placed on the practice of management. It is concluded from results obtained that "management by objectives" produces better than average perormances.

By B. C. Alberts

This. paper indicates how the South African Iron and Steel Industrial Corporation Limited (Iscor), as a major consumer of raw materials, determines the tonnage and quality of essential raw materials required to satisfy an increasing demand for steel and how this led to the establishment of a coal mine with a highly sophisticated beneficiation plant in the Waterberg coalfield, near Ellisras in the Transvaal. The planning of the project, with specific reference to the limited reserves of metallurgical coal in South Africa, the quality and quantity of the coal to be produced, and the way in which the project was managed is discussed briefly.

Jan 1, 1982

By R. D. Hancock

The complex responsible for the poisoning of anion-exchange resins is identified as the anionic cobaltic penta¬cyanide mono aquo species. It is shown that, at high concentration, this species polymerizes in solutions of pH less than 9. A mechanism for poisoning is presented that involves adsorption of anionic cobalt cyanide by a normal ion-exchange process, followed by polymerization within the resin matrix to form complexes that are too large to diffuse readily through the resin pores. The effects of resin structure and functionality on the extent of cobalt poisoning are examined, and the effect of cobalt poisoning on the kinetics and equilibrium loading of uranium is discussed.

Jan 1, 1979

By J. Keyser

The realization of an Integrated Technical Resource Asset Management System (ITRAMS) has so far evaded all software developers in the mining industry. The major factors that have prevented the development of such a system are limitations on software, hardware and network systems. Several factors have come together at Venetia Mine, which has made the undertaking of such a project both possible and desirable. This has led to the formation of a strategic partnership between Venetia Mine and Gemcom Software International Inc. This partnership is dedicated to develop and provide an Integrated Technical Resource Asset Management System based on Microsoft Back Office architecture, Gemcom for Windows™ and the MinRas system. This paper will elaborate on the phased approach of the integration of systems into the core repository, mechanisms of integration, the functionality of the system, final results, techno-economic benefits and general project management issues.

Sep 1, 2001

By D. Mark, S. R. Hunneyball

The ongoing revision of the Respirable Dust Regulations (RDR) by the UK coal mining industry includes the introduction of personal exposure monitoring for underground mines, rather than the fixed point sampling of workplaces. The initial choice CIP10 personal respirable sampler, failed during the underground trials because of the transfer of large non-respirable particles to the respirable dust deposit under vibration from man-riding belts, and of adverse effects of high winds and high dust loading on the flowrate through the sampler. These effects were validated in laboratory simulations of these conditions. A cyclone-based personal sampler is showing promise as an alternative.

Jan 1, 2003

By F. H. Deist, J. P. E. Morris, E. Georgiadis

For some years the Collieries Research Laboratory of the Chamber of Mines of South Africa has been engaged in the development and application of computer programmes to aid in the solution of rock mechanics problems. It is the purpose of this paper to introduce some of the programmes having general applicability. A system capable of predicting stresses and displacements induced by large-scale tabular excavations is discussed. A finite element programme especially designed for handling layered continuum problems, and which is being used extensively has been supplemented by an automatic mesh generation facility that reduces problem preparation times considerably. Some typical applications of these programmes are described. An entirely new approach, potentially capable of performing linear three-dimensional continuum analysis at practical cost is introduced.

By D. G. Krige

By use of models based on the South African gold-mining industry, analyses are made of the effects of changes in the mining tax structure on the .State's tax income from potential new mines; also on the percentage of such mines likely. to be proceeded with. The percentage is affected by the correlation between changes in taxation and in the flotation pay limits !or new mines. It is shown that the State stands to gain both directly and indirectly from raising the level of the capital allowance and from its extension to all mines; and that the reduced taxation resulting from a lowering of the discriminatory high tax formula for the gold mines, would, in respect of potential new mines, be compensated for by a significant increase in the percentage of such mines that would be proceeded with.

Jan 1, 1979

By P. V. Scheers

A rotating-cylinder electrode (RCE) was used to simulate the effect of flow velocity on pipe corrosion. A comparison is made between the electrochemical measurements obtained and those measured with a laboratory-scale flow loop. There is good general agreement if the speed of rotation of the RCE is adjusted to give the same value of mass transfer Coefficient as in the other system. Hence, it appears that the RCE is well suited to simulate actual flow conditions in pipes. The simultaneous effect of flow velocity and pH value on the corrosion rate of mild steel in a synthetic mine water was investigated. The i1nrease of corrosion rate was found to be more pronounced at lower pH values and, apart from a sharp increase below pH 4, the initial corrosion rate also increased at pH 7 and 6.

Jan 1, 1992

By B. W. Wallace

Permitted explosives in South Africa are those explosives approved by the relevant State authority for use in fiery coal mines. The main tests that an explosive must pass for this approval are the gallery tests derived from the Buxton (U.K.) classification. These tests are described briefly. In addition, the safety of permitted explosives is affected by their ability to deflagrate, and to produce a naked flame after blasting, rather than to detonate fully. Tests done on this phenomenon are discussed. A further potential hazard of explosives is after-blast fume. The testing and behaviour of several permitted explosives in this respect are covered, both in the laboratory and in the field. Performance testing of permitted explosives, specifically the double-pipe, underwater, and ballistic mortar tests, and their relationship to field use, are considered in some detail. The application of traditional and new tests to permitted explosives leads to guidelines for the safe and efficient formulation and use of these products.

Jan 1, 1986

By I. M. MacGregor

This paper discusses the possible use of petrological data and proximate analyses in the prediction of cutting forces for coal. It is restricted to the development of univariate predictors based on data from thirteen collieries in five major Transvaal and Orange Free State coalfields and three coal provinces. The aim of the work was the identification and development of the best predictors of mean peak cutting force and Hardgrove grindability index from among the independent variables evaluated. The data, which were obtained by use of the penetrometer developed by the Chamber of Mines Research Organization, were processed according to the SPSS computer package. The analysis revealed reasonable correlations between the Hardgrove grindability index and (1) the volatiles and vitrinite content in the Vereeniging-Sasolburg and South Rand Coalfields, (2) the contents of vitrinite, vitrinite plus exinite, and minerals plus inertinite in the Eastern Transvaal Coalfield.

Jan 1, 1985

By R. G. B. Pickering, H. H. Haase

Few innovations in the South African gold mining industry could have a more significant impact on improving profitability than non-explosive methods of mining. The far-reaching benefits of this approach are explained and the progress made through development work funded by the industry is described. Three methods are considered: impact ripping, sloting with abrasive waterjets and diamond saws, and breaking from drilled holes with waterguns and electric pulses. Of these methods, impact ripping is the most advanced and requires only minor refinements before production applications can be initiated. Although this method, based on current performance, is expected to yield considerably increased profits, it is predicted that it could perform several times better than at present with further development. The other methods of rockbreaking also show potential. Waterguns and electric rockbreaking would be attractive in unfractured rock for difficult geological conditions, and for confined areas such as gullies and development ends. Methods based on sloting could be combined with any of the other methods to enhance their effectiveness and thus yield further improvements in profitability; also, they could be used to advantage in specific applications. Al the discussed methods, therefore, deserve to be developed further.

Jan 1, 1991

By A. J. Lynch, N. W. Johnson, D. J. McKee, G. C. Thorne

The behaviour of minerals in sulphide flotation processes, with reference to simulation and control. by A. J. LYNCH, Ph.D., N. W. JOHNSON, Ph.D., D. J. McKEE, Ph.D., and G. C. THORNE, B.Sc. (Hons.) (Visitors) In sulphide flotation processes, there are two mechanisms by which particles are transferred from the flotation pulp to the concentrate: adhesion to air bubbles and natural flotation, and entrainment in the froth. The entrainment mechanism is particularly important for particles of non-sulphide gangue, which do not absorb collector. The importance of controlling the recovery rate of water was illustrated in plant testwork in which selectivity between valuable sulphides and sulphide gangue, and between valuable sulphides and non-sulphide gangue, was altered by manipulation of variables affecting the water recovery rate. The two mechanisms should be recognized in the development of a control system. Most of the control schemes in operating plants have concentrated on reagent additions, which affect the natural flotation mechanism. Although control of the chemical environment is clearly of paramount importance in flotation, plant tests have shown that control of the variables affecting the entrainment mechanism is also important.

Jan 4, 1974

By M. A. de Ruijter

Bracken Gold Mine ceased mining operations during February 1993. The clean-up of the gold plant, which had already commenced in September 1992, was completed in January 1994. The mine had been in production since early in 1962 but, because of a decreasing ore reserve, increasing working costs, and a relatively low gold price, closure had become inevitable. The closure had been under consideration since August 1983, when the first estimate was made regarding the amount of gold that could be recovered from the clean-up operations. Until that stage, it had been accepted that Bracken would conform to the commonly accepted idea that 0.25% of the total gold produced by the plant would be recovered during the clean-up operation. This idea was dispelled when the initial estimates indicated that the gold recovery would vary between 0.049 and 0.095%. The actual figure realized was 0.036%, showing that there is no generalforl1ula for the calculation of the amount of gold to be recovered from such clean-up operations. During the clean-up operation, Bracken became an unexpected contributor to the State's Reconstruction and Development Programme by having al the mine and plant buildings purchased and converted into a community development centre. This shortene4 the time available for the clean-up, and several of the buildings remained intact. However, the foundations and sub-soils had been sampled extensively, and it is considered that no recoverable gold was left behind.

Jan 1, 1996

By L. C. Stilwell

The paper will place into perspective the contribution that platinum makes to the South African economy. It will use statistics from official sources, namely the Department of Minerals and Energy, the Department of Customs and Excise, the South African Reserve Bank and Statistics South Africa. Surprisingly few people are aware of these statistics, especially Supply and Usage tables, published by Statistics South Africa, and trade statistics, published by the Customs and Excise division of the South African Revenue Service. The paper will therefore contain a concise explanation of input-output tables and supply usage tables, as well as the derivation of gross domestic product and an outline of the System of National Accounts, of which Input-Output Tables and supply and usage tables are components. GDP is a commonly used, but poorly understood, measure of the wealth of an economy. The paper will explain the methods used by SSA to calculate this indicator and its place in the System of National Accounts (SNA). South Africa exports almost all its platinum production (87.5% in 2002). Exports are a final demand, as opposed to intermediate demand from secondary industries, and therefore do not enter the value-adding process, which is the essence of GDP. By definition, therefore, platinum on its own is not a major contributor to GDP. The platinum industry does, however, have an impact (known as the multiplier effect) on other sectors of the economy. The paper will explain the meaning and derivation of these multipliers, using a model based on an Inverse Leontief Matrix.

Jan 1, 2004

By D. R. Hardman

South Africa is the third-largest supplier of coal on the world's export markets after Australia and the USA, and the second-largest supplier of bituminous steam coal following Australia. There are many Similarities between the coal industries of South Africa and those of Australia and the USA, in contrast to the coal industries in Europe. For South Africa to maintain a competitive position on the export markets, it must continue to compete against these two countries. It is therefore important that the performance of the loca1 coal industry should against that of the Australian and US coal industries. Although financial performance is the major criterion, financial information is not easily obtained, and the paper therefore uses employee productivity in the form of tonnes per man year as a means of comparison. The paper reviews recent trends in the level of production and numbers of employees prior to review1ng the productivity. The influence on productivity of some mining methods is highlighted. It is realized that published information (information available within the public domain) can contain anomalies, but every effort is made to compare data of a similar type. Notwithstanding possible inaccuracies, it is shown that South African coal-De productivity lags far behind that of Australia and the USA. The significance of the difference is that the South African coal industry is able to apply overseas practices and procedures that have been shown to give improved performance, and that the increased use of more productive extraction techniques has limited application.

Jan 1, 1996

By R. P. King

The University of the Witwatersrand (Wits) and the minerals industry of South Africa have grown with the city of Johannesburg. The former has provided teaching and research in mining and metallurgy, while the latter has been responsible for the practical training of metallurgists and for the testing and implementation of innovative ideas proposed by the academics. This interplay between inventiveness and industrial application is illustrated by three examples: the establishment of the iron and steel industry as a result of the persistent experimentation undertaken by Professor G. H. Stanley, the first Professor of Metallurgy and Assaying at the South African School of Mines, which later became Wits; the establishment of the research organization that eventually became the Council for Mineral Technology (Mintek) - again through Professor Stanley's faith in the role of research; and the establishment at Wits of physical metallurgy as a discipline in its own right, as first suggested by Professor C. E. Mavrocordatos of Wits against the opinion of his colleagues in the industry. The Department of Metallurgy at Wits has been well supported by the minerals industry. Not only does the industry provide grants for the financial support of students, but it supplements the salaries of personnel in the Department, making possible the recruitment of top-class academic staff. At present the greatest problem is the lack of interest shown by matriculants in the metallurgical industry as a career. However, an enormous effort is being made by the Chamber of Mines, The South African Institute of Mining and Metallurgy, and the Wits Department of Metallurgy to ensure that matriculants receive appropriate information about the career prospects in the minerals industry.

Jan 1, 1983

By H. A. D. Kirsten

Mining-induced seismicity is usually evaluated in terms of continuum elastic analyses, and is quantified in terms of energy release rate as state parameter and excess shear stress along particular features on which failure may be induced. Although both of these quantities are representative measures of potential seismic activity, elastic analyses do not enable the associated stresses and displacements in the rock in which failure occurs to be evaluated reliably. The paper compares the effect of depth, span, support stf1Jhess, field stress ratio, and discontinuity strength on mining induced seismicity determined from elastic analyses and from analyses in which discontinuities in the rock are allowed to fall. It is, accordingly, shown that the incidence and magnitudes of potential seismic events and the net excess shear as representative state parameter cannot be determined reliably from elastic analyses that do not account for the failure of ubiquitous discontinuities. The magnitudes of seismic events in rock in which ubiquitous discontinuities are allowed to fail are very considerably overestimated in elastic analyses. The extent of the seismic source region and the associated seismicity do not increase with depth, which, together with the improved containment of the concomitant rockburst damage by backfill is reassuring for mining at greater depth in future. For conventional support, the magnitude of potential seismicity increases for an increase in span in elastic rock, but remains unaffected in non-elastic rock. For backfill, the magnitude of potential sesmicity decreases substantially in elastic and non-elastic rock for an increase in span. Increases infield stress ratio very significantly reduce potential seismicity irrespective if the type if analysis, but effect the distribution if potential seismic events very differently in elastic and non-elastic rock.

Jan 1, 1994