Search Documents

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica,-the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclone are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2004

By J. C. Coetzee

In this article, a case is made for the importance of the transfer and management of tacit knowledge to ensure continued sustainable competitive advantage within the pyrometallurgical industry in South Africa. The state of knowledge management (KM) is assessed through a theoretical and empirical study. The empirical part of the study was conducted by means of a survey questionnaire. An important prerequisite within the research entailed determining the current state of KM within the pyrometallurgical industry, and the findings are presented throughout this article. The research argues for initiatives to address the high turnover of pyrometallurgical knowledge workers. This industry needs to entrench tacit knowledge and therefore address the problems associated with the continuous loss of inherent specialized knowledge. Appropriately, emphasis is placed on identifying initiatives required to embed and retain not only human capital lost through mobility, but rather retaining tacit knowledge through a practical KM framework.

Jan 1, 2012

By E. Bakhtavar, R. Mikaeil, D. Khademi

"Fuzzy-weighted integer goal programming has been developed and used to select the most suitable site to construct a central processing plant for several adjacent small-scale dimension stone quarries, based on the most effective criteria. In the first step of mathematical modelling, the most important goals and decision variables were defined. Accordingly, an objective function was used in the model for minimizing the sum of undesired fuzzy-weighted deviations. Fuzzy weights were determined by a matrix of pairwise comparisons of various expert judgments in this field and the fuzzy geometric mean. The goal and systemic constraints were also modelled. The most suitable site for the construction of the plant was selected after solving the mathematical model in the ExcelR Solver add-in. The selected site had various advantages over the other sites, such as the shortest average distance to the quarries, the shortest distance to power access and workforce, and the lowest land price. IntroductionSelection of the most suitable site of a plant is one of the most important considerations when constructing an industrial project. A suitable site has a significant effect on a company's competitiveness in the market. Selecting a desirable location for constructing plants such as mineral processing facilities is an essential part of the economic planning that will enable a company to meet the needs of related upstream and downstream operations. These units are considered to be best built near the relevant mining sites because of technical difficulties, the cost of transporting minerals, and the traffic hazard caused by the movement of trucks transporting materials. Two main types of research using multiattribute decision-making models have been reported for selection of a processing plant site (Safari et al. 2010, 2012). In that research, the analytic hierarchy process (AHP) and fuzzy technique for order preference by similarity to ideal solution (TOPSIS) approach were applied to select the suitable locations for the mineral processing plants for phases 1 and 2 of Sangan iron ore mine."

Jan 1, 2017

By JOURNAL SAIMM

SYMPOSIUM ON PELLETS AND GRANULES During October 1974, the Newcastle branch of the Australasian Institute of Mining and Metallurgy is to hold a symposium on pelletizing and granulation, with particular reference to the iron ore, fertilizer, and cement industries.

Jan 12, 1973

By K. Harlow

"Zircon is a naturally occurring radioactive material (NORM) and as such is subject to a variety of regulations around the world. The regulatory processes and their implementation are summarized and the key issues affecting zircon and zirconia highlighted. Having absorbed the activities of the former Zircon Minerals Committee, the strategy of the Zircon Industry Association (ZIA) is to be the ‘go-to place’ for information on these matters, and its activities in the NORM space are described. Chemical industry regulations such as REACH are spreading around the world, and the paper provides an update of their status in the key jurisdictions. As mineral sands are transported to market in oceangoing vessels, they are subject to the regulations of the International Maritime Organization, which are summarized in the paper. IntroductionFrom a global perspective, zircon is generally not found in high concentrations other than in placer and dune deposits where it has been deposited along with other heavy minerals such as ilmenite, rutile, and monazite. Such deposits have been sorted and concentrated over geological time by the action of tides, waves, and wind to form concentrated deposits of heavy minerals along old coastlines and in river beds and deltas. Consequently, zircon is mostly found in association with the principal titanium minerals ilmenite and rutile. These secondary concentrations in placer deposits provide the commercial sources of zircon.All geological materials contain natural radioactivity, although the term NORM (naturally occurring radioactive material) is mostly used for minerals and other materials with above-average uranium and thorium concentrations. Importantly, the radioactive nature of zircon has not changed, but the way in which radioactivity is viewed by regulators has, affecting the zircon industry throughout the value chain."

Jan 1, 2017

By L. Morin, S. Mortazavi, K. Volchek, A. Demers, A. Di Feo

The objective of this paper was to investigate the possibility of reducing process (fresh) water and increasing recycled water (thickener tank overflow water). As part of the investigation, rougher flotation tests were done with the two water types and a mixture of the two (50%/50%). The effect of recycled water on the grade-recovery response and rougher recoveries was investigated. When thickener tank overflow was used (50% and 100%), the nickel+copper grade versus nickel recovery decreased. The decrease in the grade-recovery was due to higher pyrrhotite recovery. Also, there were no effects on nickel and copper recoveries, which was confirmed using multivariate statistical analysis at the 95% significance level. Keywords: Flotation, nickel, copper, water recycling, multivariate statistical analysis, MANOVA, reverse osmosis

Jan 1, 2020

By G. D. Schena

The issue of evaluating the economic impact of large mineral projects in developing countries was studied by the use of econometric models. The evaluating system is demonstrated by its application to an example from Namibia. Three-dimensional graphics are used to illustrate the procedures leading to an assessment of the economic effects of the mineral development. The analysis allows the assessment of the overall economic consequences of mineral developments where there is a need to incorporate in the evaluation issues that are broader in scope than the pure financial objectives. Sets of technical coefficients are exploited for the development of input-output models of the productive structure of an economy. The models are refined to incorporate country-specific behaviours. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy wide effects associated with a new project in the mineral sector of a developing country. Synthetic measures of profitability at market and shadow prices are introduced, and the cost/benefit ratio is used to rank mineral projects according to their economic profitability. The cost is the capital mobilized for the development of the project and for increasing the productive capacity of the related satellite industries. The benefits are identified with the economy-wide increase in value added induced by the project. 80th costs and benefits are initially valued at market prices. Their ratio is likely to be an index of economic profitability superior to measures that concentrate exclusively on the benefit side of projects. To allow for market distortions, the concept of shadow prices is introduced, and accordingly project-related costs and benefits are re-evaluated. A new cost/benefit ratio at shadow prices is recalculated, which is more meaningful to the policy-maker than decision-making based on socio-economic issues.

Jan 1, 1993

By R. W. O. Kersten

Backfilling is one of the options available to the mining engineer in mine design. The decision as to the type of backfill is dependent on the purpose for which it will be used. For example, in a situation where high-grade, steeply dipping multiple reefs are to be mined, the purpose would be the following: ? to facilitate maximum extraction; a ? to minimize loss of fines; ? to allow closely spaced multiple reefs to be mined; and a ? to create a working platform. The physical properties required which will satisfy the abovementioned requirements can then be defined; the design of the fill plant, as well as the transport of the fill, will be governed by these considerations. The same procedure is also adopted in deciding on backfill in single- reef gold mines. The first question to be asked is the purpose of the fill. It may be to reduce the energy release rate, for environmental reasons, to reduce timber usage, to improve productivity, to reduce stoping costs, to obtain higher mining extraction, and so on. Only after one, or a combination, of these factors has been selected, can the specifications for the fill be decided on, and the plant designed accordingly. The introduction of backfill at Sheba Gold Mine will be used to illustrate the procedure adopted by Anglovaal in determining the type of fill required.

Jan 1, 1988

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By L. A. Vermeulen, C. P. Campbell, D. D. Howat

The production 01material liner than 75 µm in a number of open-circuit mills was investigated. The mils ranged from laboratory rod and ball mils treating a variety 01 ores to large industrial rod mils treating gold and copper ores. It was shown that the dependence on feed rate 01 the production 01 material liner than 751J.1T1 can be accurately described by a simple formula that was derived in previous work. In some 01 the systems reviewed, it proved possible to assess the feed rate 01 ore to the mil at which the rate 01 production 01 material finer than 75 µm can be maximized.

Jan 1, 1991

By T. Flitton, R. Peattie

"The extreme depths and consequent expense of drilling and sampling the gold-bearing reefs of the Witwatersrand Basin have resulted in limited data being available for estimation of grade ahead of the mining face. There is, however, a wealth of information from mined-out areas of these deposits. This estimation challenge resulted in the development of a unique method of Mineral Resource estimation.AngloGold Ashanti (AGA) utilizes a technique termed macro cokriging (MCK), which allows for the integration of the limited advanced borehole data with the large chip sample data-sets from the previously mined-out areas by adopting a Bayesian geostatistical approach. The MCK process, in short, is the estimation of mixed support size data together with the application of four-parameter distribution models.The gold value estimation for the Carbon Leader Reef (CLR) on the AGA TauTona Mine is used in this paper as a case study of the process and to demonstrate the effectiveness of this technique through production reconciliation. The current method has been proven over the last 20 years and is now an established part of the Mineral Resource evaluation process within AGA.IntroductionOwing to the extreme depths of the goldbearing reefs at the AngloGold Ashanti (AGA) Witwatersrand operations and the prohibitive expense and time involved in drilling boreholes to the required depth, only limited drilling and sampling data is available ahead of the mining face. Whereas traditional estimation techniques are interpolative, within the Witwatersrand the estimation is primarily extrapolative, with the majority of the data being sourced from the mined-out areas. This significant challenge to estimation resulted in the development of a unique method of Mineral Resource estimation and evaluation."

Jan 1, 2016

By S. Rupprecht, G. Rapson

Long blast hole drilling has been successfully implemented since the 1950s in caving operations, steeply dipping wide reefs and boxhole/raise developments worldwide. However, when applying long hole drilling to narrow tabular reefs, the challenges of achieving high economic drilling rates, combined with acceptable accuracy and appropriate powder factors have yet to be overcome. The focus in this paper is the selection, application and optimization of long hole drilling equipment at mining operations shallower than 2 000 meters. The drilling, blasting and cleaning operations have to be optimized as a process if maximum production at minimum per unit cost is to be achieved. For this to be possible, it is essential that the mine design and layout match the mining process being implemented. The critical parameters affecting the sustainable implementation of long hole drilling in stoping applications for platinum mines are improved safety and higher production rates compared to conventional methods. In terms of drilling, both top hammer and down-the hole hammer configurations have been considered. For economic drilling, the benefits of monitoring and optimizing performance (i.e. drill bit rotation, thrust, and percussive power) for specific rock types are discussed. While the drive is for longer, more accurate, smaller diameter holes to reduce drilling costs, the design of appropriate blast hole patterns and the corresponding charging and initiation systems is crucial for success. The effect of hole diameter and pattern on the powder factor, when comparing small diameter, shorter holes versus large diameter, longer holes, is a major factor in achieving good blasting results. Once appropriate drilling and blasting have been implemented, the cleaning process becomes a potentially critical operation to ensure the production, cost and safety goals are met. Hence, the blast hole pattern and charge have to be integrated for optimal fragmentation to suit the cleaning cycle for maximum production output. Providing that long blast hole drilling is applied as a process in a planned, committed and well-managed manner, the benefits in safety, production and cost over conventional methods should be achievable. However, if the implementation process is not planned and supported by all parties concerned, it will not be possible to succeed in the new operation. Hence, an implementation or roll-out plan of new technology is crucial for success.

Jan 1, 2004

The mining rock-mass rating (MAMA) classification system was introduced in 1974 as a development of the CSIA geomechanics classification system to cater for diverse mining situations. The fundamental difference was the recognition that in situ rock-mass ratings (AMA) had to be adjusted according to the mining environment so that the final ratings (MAMA) could be used for mine design. The adjustment parameters are weathering, mining-induced stresses, joint orientation, and blasting effects. It is also possible to use the ratings (AMA) in the determination of empirical rock-mass strength (AMS) and then in the application of the adjustments to arrive at a design rock-mass strength (DAMS). This classification system is versatile, and the rock-mass rating (AMA), the mining rock-mass rating (MAMA), and the design rock-mass strength (DAMS) provide good guidelines for the purposes of mine design. However, in some cases a more detailed investigation may be required, in which case greater attention is paid to specific parameters of the system. Narrow and weak geological features that are continuous within and beyond the stope or pillar must be identified and rated separately. The paper describes the procedure required to arrive at the ratings, and presents practical examples of the application of the system to mine design.

Jan 1, 1990

The structural design of a pavement relates to the ability of the road to carry the imposed loads without the need for excessive maintenance or rehabilitation. Current techniques for the structural design of haulage roads are empirical and based primarily on the previous experience of personnel assigned to pavement design, both in terms of the strength of the structure and the quality of the wearing course material. This has the potential for unwarranted expenditure on too thick a structure or, conversely, premature deformation leading to the need for excessive expenditure on maintenance. Furthermore, the effect of larger haulage vehicles on the structural performance of a pavement cannot be predicted. Thus, there is a need to develop a portable and practical method of structural design. This paper presents an overview of structural design methods for mine haulage roads and, through an analysis and quantification of the structural performance of existing pavements, recommends the mechanistic design procedure, together with a revised structural design and associated limiting design criteria. It is concluded that the application of the mechanistic method to a design project can reduce the costs of haulage roads construction and accrue additional benefit in terms of reduced operating and maintenance costs.

Jan 1, 1996

By N. Saldía, C. Riveros, R. Hills, S. Barrera

The transport of tailings composites provided by different sources is a field of study where a limited amount of research has been conducted. Nevertheless, such systems are important sources of operational difficulties, especially in the case of high clay content tailings. The case presented in the present paper consists of a free surface flow pipeline transporting a composite of two different tailings with high clay content. It has presented operational difficulties such as partial blockages and upstream box and air intake overtopping events. In the present paper, the causes of these difficulties are identified. These include lack of complete mixing of the different tailings, multi-layered flow with low velocity and high yield values with high frictional losses. The pipeline characteristics and performance are analysed in three stages: design, initial operation and enhanced operation, the latter accomplished by means of increasing turbulence in the box located upstream from the pipeline. The last section of the pipeline and another distribution pipeline system located downstream from the pipeline have performed well. The cause of different behaviour of both systems is also assessed.

Jan 1, 2007

This overview serves as an introduction to the succeeding paper in this issue, that entitled 'The design of backfill as a support for Polish coal mines' by Professor J. Palarski. As such, it briefly describes the coal-mining methods, production, and mining education in Poland. It ends with a brief account of Professor Palarski's qualifications and experience in the fields of backfilling and hydro transport.

Jan 1, 1994

By A. M. Sage

This paper reviews the metallurgical functions of vanadium in high-strength Iow-alloy steels, and discusses the ways in which vanadium is used in various types of steel supplied as reinforcing bars, plates, sections, and strip. Potential developments to meet new engineering requirements are discussed briefly.

Jan 1, 1984

By F. Shaw, E. C. Chemaly, A. F. S. Schoukens

Steel-plant dusts are hazardous waste materials, containing toxic constituents such as lead, cadmium, and hexavalent chromium. These dusts can be treated by a number of thermal processes, which are described as used in Western Europe and the USA. A detailed description is then given of the thermal Enviroplas process, which as developed at Mintek and produces disposable slag and valuable byproducts such as ferroalloys containing chromium and nickel, and fumes high in zinc oxide.

Jan 1, 1993

By H. Xuchun, H. Nailian, L. Guoqing

With the accession to WTO and the establishment of Shanghai Gold Exchange, gold mines in China are facing more severe competition from both home and abroad. Supply Chain Management (SCM), a new management idea gradually accepted all over the world, provides the gold mines in China with a new management mode. In this thesis, under the guidance of SCM theory, based on the analyzing to the actualities of Jiaojia Gold Mine, the Jiaojia supply chain framework is constructed, the function system for Jiaojia SCM is configured, and function modules are described in detail. Keywords: Supply Chain Management, Gold mine, Informatization

Jan 1, 2003

By W. O. Ortlepp

This note considers the most fundamental concepts of support design for deep underground openings and discusses them briefly in the context of tabular stoping and deep hard-rock tunnelling. It concludes that the conventional re-bar, mesh, and lacing methods that have been widely used in deep gold mines are quite inappropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit.

Jan 1, 1995