Search Documents

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By G. D. Schena

The issue of evaluating the economic impact of large mineral projects in developing countries was studied by the use of econometric models. The evaluating system is demonstrated by its application to an example from Namibia. Three-dimensional graphics are used to illustrate the procedures leading to an assessment of the economic effects of the mineral development. The analysis allows the assessment of the overall economic consequences of mineral developments where there is a need to incorporate in the evaluation issues that are broader in scope than the pure financial objectives. Sets of technical coefficients are exploited for the development of input-output models of the productive structure of an economy. The models are refined to incorporate country-specific behaviours. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy wide effects associated with a new project in the mineral sector of a developing country. Synthetic measures of profitability at market and shadow prices are introduced, and the cost/benefit ratio is used to rank mineral projects according to their economic profitability. The cost is the capital mobilized for the development of the project and for increasing the productive capacity of the related satellite industries. The benefits are identified with the economy-wide increase in value added induced by the project. 80th costs and benefits are initially valued at market prices. Their ratio is likely to be an index of economic profitability superior to measures that concentrate exclusively on the benefit side of projects. To allow for market distortions, the concept of shadow prices is introduced, and accordingly project-related costs and benefits are re-evaluated. A new cost/benefit ratio at shadow prices is recalculated, which is more meaningful to the policy-maker than decision-making based on socio-economic issues.

Jan 1, 1993

By R. W. O. Kersten

Backfilling is one of the options available to the mining engineer in mine design. The decision as to the type of backfill is dependent on the purpose for which it will be used. For example, in a situation where high-grade, steeply dipping multiple reefs are to be mined, the purpose would be the following: ? to facilitate maximum extraction; a ? to minimize loss of fines; ? to allow closely spaced multiple reefs to be mined; and a ? to create a working platform. The physical properties required which will satisfy the abovementioned requirements can then be defined; the design of the fill plant, as well as the transport of the fill, will be governed by these considerations. The same procedure is also adopted in deciding on backfill in single- reef gold mines. The first question to be asked is the purpose of the fill. It may be to reduce the energy release rate, for environmental reasons, to reduce timber usage, to improve productivity, to reduce stoping costs, to obtain higher mining extraction, and so on. Only after one, or a combination, of these factors has been selected, can the specifications for the fill be decided on, and the plant designed accordingly. The introduction of backfill at Sheba Gold Mine will be used to illustrate the procedure adopted by Anglovaal in determining the type of fill required.

Jan 1, 1988

By T. Flitton, R. Peattie

"The extreme depths and consequent expense of drilling and sampling the gold-bearing reefs of the Witwatersrand Basin have resulted in limited data being available for estimation of grade ahead of the mining face. There is, however, a wealth of information from mined-out areas of these deposits. This estimation challenge resulted in the development of a unique method of Mineral Resource estimation.AngloGold Ashanti (AGA) utilizes a technique termed macro cokriging (MCK), which allows for the integration of the limited advanced borehole data with the large chip sample data-sets from the previously mined-out areas by adopting a Bayesian geostatistical approach. The MCK process, in short, is the estimation of mixed support size data together with the application of four-parameter distribution models.The gold value estimation for the Carbon Leader Reef (CLR) on the AGA TauTona Mine is used in this paper as a case study of the process and to demonstrate the effectiveness of this technique through production reconciliation. The current method has been proven over the last 20 years and is now an established part of the Mineral Resource evaluation process within AGA.IntroductionOwing to the extreme depths of the goldbearing reefs at the AngloGold Ashanti (AGA) Witwatersrand operations and the prohibitive expense and time involved in drilling boreholes to the required depth, only limited drilling and sampling data is available ahead of the mining face. Whereas traditional estimation techniques are interpolative, within the Witwatersrand the estimation is primarily extrapolative, with the majority of the data being sourced from the mined-out areas. This significant challenge to estimation resulted in the development of a unique method of Mineral Resource estimation and evaluation."

Jan 1, 2016

By L. A. Vermeulen, C. P. Campbell, D. D. Howat

The production 01material liner than 75 µm in a number of open-circuit mills was investigated. The mils ranged from laboratory rod and ball mils treating a variety 01 ores to large industrial rod mils treating gold and copper ores. It was shown that the dependence on feed rate 01 the production 01 material liner than 751J.1T1 can be accurately described by a simple formula that was derived in previous work. In some 01 the systems reviewed, it proved possible to assess the feed rate 01 ore to the mil at which the rate 01 production 01 material finer than 75 µm can be maximized.

Jan 1, 1991

By S. Rupprecht, G. Rapson

Long blast hole drilling has been successfully implemented since the 1950s in caving operations, steeply dipping wide reefs and boxhole/raise developments worldwide. However, when applying long hole drilling to narrow tabular reefs, the challenges of achieving high economic drilling rates, combined with acceptable accuracy and appropriate powder factors have yet to be overcome. The focus in this paper is the selection, application and optimization of long hole drilling equipment at mining operations shallower than 2 000 meters. The drilling, blasting and cleaning operations have to be optimized as a process if maximum production at minimum per unit cost is to be achieved. For this to be possible, it is essential that the mine design and layout match the mining process being implemented. The critical parameters affecting the sustainable implementation of long hole drilling in stoping applications for platinum mines are improved safety and higher production rates compared to conventional methods. In terms of drilling, both top hammer and down-the hole hammer configurations have been considered. For economic drilling, the benefits of monitoring and optimizing performance (i.e. drill bit rotation, thrust, and percussive power) for specific rock types are discussed. While the drive is for longer, more accurate, smaller diameter holes to reduce drilling costs, the design of appropriate blast hole patterns and the corresponding charging and initiation systems is crucial for success. The effect of hole diameter and pattern on the powder factor, when comparing small diameter, shorter holes versus large diameter, longer holes, is a major factor in achieving good blasting results. Once appropriate drilling and blasting have been implemented, the cleaning process becomes a potentially critical operation to ensure the production, cost and safety goals are met. Hence, the blast hole pattern and charge have to be integrated for optimal fragmentation to suit the cleaning cycle for maximum production output. Providing that long blast hole drilling is applied as a process in a planned, committed and well-managed manner, the benefits in safety, production and cost over conventional methods should be achievable. However, if the implementation process is not planned and supported by all parties concerned, it will not be possible to succeed in the new operation. Hence, an implementation or roll-out plan of new technology is crucial for success.

Jan 1, 2004

The mining rock-mass rating (MAMA) classification system was introduced in 1974 as a development of the CSIA geomechanics classification system to cater for diverse mining situations. The fundamental difference was the recognition that in situ rock-mass ratings (AMA) had to be adjusted according to the mining environment so that the final ratings (MAMA) could be used for mine design. The adjustment parameters are weathering, mining-induced stresses, joint orientation, and blasting effects. It is also possible to use the ratings (AMA) in the determination of empirical rock-mass strength (AMS) and then in the application of the adjustments to arrive at a design rock-mass strength (DAMS). This classification system is versatile, and the rock-mass rating (AMA), the mining rock-mass rating (MAMA), and the design rock-mass strength (DAMS) provide good guidelines for the purposes of mine design. However, in some cases a more detailed investigation may be required, in which case greater attention is paid to specific parameters of the system. Narrow and weak geological features that are continuous within and beyond the stope or pillar must be identified and rated separately. The paper describes the procedure required to arrive at the ratings, and presents practical examples of the application of the system to mine design.

Jan 1, 1990

The structural design of a pavement relates to the ability of the road to carry the imposed loads without the need for excessive maintenance or rehabilitation. Current techniques for the structural design of haulage roads are empirical and based primarily on the previous experience of personnel assigned to pavement design, both in terms of the strength of the structure and the quality of the wearing course material. This has the potential for unwarranted expenditure on too thick a structure or, conversely, premature deformation leading to the need for excessive expenditure on maintenance. Furthermore, the effect of larger haulage vehicles on the structural performance of a pavement cannot be predicted. Thus, there is a need to develop a portable and practical method of structural design. This paper presents an overview of structural design methods for mine haulage roads and, through an analysis and quantification of the structural performance of existing pavements, recommends the mechanistic design procedure, together with a revised structural design and associated limiting design criteria. It is concluded that the application of the mechanistic method to a design project can reduce the costs of haulage roads construction and accrue additional benefit in terms of reduced operating and maintenance costs.

Jan 1, 1996

By N. Saldía, C. Riveros, R. Hills, S. Barrera

The transport of tailings composites provided by different sources is a field of study where a limited amount of research has been conducted. Nevertheless, such systems are important sources of operational difficulties, especially in the case of high clay content tailings. The case presented in the present paper consists of a free surface flow pipeline transporting a composite of two different tailings with high clay content. It has presented operational difficulties such as partial blockages and upstream box and air intake overtopping events. In the present paper, the causes of these difficulties are identified. These include lack of complete mixing of the different tailings, multi-layered flow with low velocity and high yield values with high frictional losses. The pipeline characteristics and performance are analysed in three stages: design, initial operation and enhanced operation, the latter accomplished by means of increasing turbulence in the box located upstream from the pipeline. The last section of the pipeline and another distribution pipeline system located downstream from the pipeline have performed well. The cause of different behaviour of both systems is also assessed.

Jan 1, 2007

This overview serves as an introduction to the succeeding paper in this issue, that entitled 'The design of backfill as a support for Polish coal mines' by Professor J. Palarski. As such, it briefly describes the coal-mining methods, production, and mining education in Poland. It ends with a brief account of Professor Palarski's qualifications and experience in the fields of backfilling and hydro transport.

Jan 1, 1994

By A. M. Sage

This paper reviews the metallurgical functions of vanadium in high-strength Iow-alloy steels, and discusses the ways in which vanadium is used in various types of steel supplied as reinforcing bars, plates, sections, and strip. Potential developments to meet new engineering requirements are discussed briefly.

Jan 1, 1984

By F. Shaw, E. C. Chemaly, A. F. S. Schoukens

Steel-plant dusts are hazardous waste materials, containing toxic constituents such as lead, cadmium, and hexavalent chromium. These dusts can be treated by a number of thermal processes, which are described as used in Western Europe and the USA. A detailed description is then given of the thermal Enviroplas process, which as developed at Mintek and produces disposable slag and valuable byproducts such as ferroalloys containing chromium and nickel, and fumes high in zinc oxide.

Jan 1, 1993

By H. Xuchun, H. Nailian, L. Guoqing

With the accession to WTO and the establishment of Shanghai Gold Exchange, gold mines in China are facing more severe competition from both home and abroad. Supply Chain Management (SCM), a new management idea gradually accepted all over the world, provides the gold mines in China with a new management mode. In this thesis, under the guidance of SCM theory, based on the analyzing to the actualities of Jiaojia Gold Mine, the Jiaojia supply chain framework is constructed, the function system for Jiaojia SCM is configured, and function modules are described in detail. Keywords: Supply Chain Management, Gold mine, Informatization

Jan 1, 2003

By W. O. Ortlepp

This note considers the most fundamental concepts of support design for deep underground openings and discusses them briefly in the context of tabular stoping and deep hard-rock tunnelling. It concludes that the conventional re-bar, mesh, and lacing methods that have been widely used in deep gold mines are quite inappropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit.

Jan 1, 1995

By O. G. Pauw

The relationships between mill power and pebble load, bulk density of the load, and circulating load were investigated on the pebble mills in the grinding circuit at Buffelsfontein Gold Mine. This paper describes the most significant relationships among the operating and control variables on the plant, and illustrates these by reference to experimental data gathered from the plant during operation. The results were used for the development of very successful multivariable peak-seeking controllers for the pebble load and bulk density of the load on these pebble mills. The peak-seeking control algorithms are described in detail. The control system has operated successfully at Buffelsfontein for more than 18 months and is still in operation.

Jan 1, 1985

By B. P. Gilbertson

In her wonderful book, 'The Guns of August', historian Barbara Tuchman tells us that the French war plan for 1914 was dedicated entirely to an offensive strategy, not a defensive one. Plan 17, as it was called, concentrated everything on a French advance to the Rhine, leaving the French left virtually unguarded. This strategy could only be justified by the fixed belief that the Germans could not deploy sufficient manpower to extend their invasion around through western Belgium and the low provinces; and this in turn was based on the belief that the Germans would never use reserve troops in the front line. Al evidence to the contrary was ignored. But when the war came, the Germans followed Count Von Schlieffen's plan; they did use reserves in the front line and they did come the long way around on the west. The result- as you know-was a protracted war, with fearful consequences for the rest of our century.

Jan 1, 1994

By M. C. Mulligan

Counter current decantation (CCD) thickener circuits are used to recover soluble metal as pregnant liquor solution from ore leach residue. The basis of CCD operation is to concentrate suspended solids thereby minimizing liquor content in underflow slurry that flow in one direction. Then the underflow slurry liquor is diluted with wash liquor that flows in the opposite direction and the suspended solids are concentrated again and again. The amount of liquor in the thickener underflow contributes to determining the number of CCD stages required to recover the desired amount of soluble metal. Furthermore, similar results could be achieved at a lower wash quantity, reducing the size of downstream equipment. High density thickeners (HDT) are designed to use gravity and compression, and minimize the amount of liquor in the underflow thus minimizing the number of CCD stages. This paper reviews the process used to select HDTs rather than high rate thickeners (HRT) for the Ruashi II copper-cobalt hydrometallurgical process in the Democratic Republic of Congo (DRC), using laboratory HDT simulations, to CCD simulations and thickener design details.

Jan 1, 2009

The results of small-scale resin-in-pulp pilot-plant investigations at Grootvlei Proprietary Mines Ltd, President Brand Gold Mining Co. Ltd, and Western Areas Gold Mine Co. Ltd are reported. At each mine, a pulp was fed simultaneously to a carbon-in-pulp plant, allowing a direct comparison of the metallurgical performance of the two processes. With the Grootvlei pulp, gold was extracted more efficiently by resin than by carbon owing to the Iow concentration of competing base-metal cyanide complexes in solution. With the Western Areas pulp, the reverse was true because of the high concentrations of copper and nickel in solution. Finally, with the President Brand pulp, resin-inpulp was significantly superior to carbon-in-pulp owing mainly to the inherently slow rate of gold extraction from calcine by activated carbon. Results are presented that show the efficiency of the elution of gold and other elements with a variety of reagents from the loaded resins arising from these three campaigns. At Western Areas, a detailed investigation enabled a preliminary cost evaluation to be made of three techniques for the elution of strong-base resins.

Jan 1, 1984

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By W. F. Heinz

The efficient and effective handling and logistics of materials for underground support is an important part of mine mechanization and automation. Support systems based on backfill material or grout slurries and pastes transported underground through pipelines (ranges) lend themselves to a large degree of mechanization. In contrast the installation of conventional support systems such as props, timber packs, brick packs etc., requires more handling and hence is labour intensive and more costly. RODIO/ROSOND has developed and improved significantly its high density slurry/low density paste conveyance system on surface and underground during recent years. The surface batching and pumping stations are computer controlled and operate with a minimum labour complement. The RODIO/ROSOND grout pack support system has some unique features such as the use of relay stations, which result in the following distinct advantages and benefits to mining operations: • No interference with shaft operations • No grout ranges under high pressure in shaft • Efficient reticulation from underground relay stations • Low capital cost • Better control of quality of materials (high density slurry/low density paste) placed • Proximity of the working place to the relay station facilitates control of installation. These specific characteristics of RODIO/ROSOND’s grout pack support system have resulted in more economical support for several mines in South Africa and Australia.

Sep 1, 2001