Search Documents

By S. A. Ziebold

There is often a need to increase capacity through existing mist eliminator installations without significant tower modifications. Often there is not enough extra space outside existing vessels unless more expensive changes can be justified. Also, plant downtime must be considered. The challenge in retrofitting is to overcome velocity limitations inherent in the design while at the same time extend performance capability. The solution most often is to create new ways to add extra filter area while remaining constrained to the existing space. This strategy, however, can dangerously backfire if basic design principles are not followed. Mist eliminator design is a complex integration of many conflicting performance parameters. Often the objective is to increase scrubbing capacity while maximizing collection efficiency and service life and minimizing operating pressure drop (energy cost), particle regeneration (re-entrainment) and overall maintenance costs. Results of plant retrofitting using mesh pads, impaction fibre beds and diffusion fibre beds are presented based on actual plant projects. Often the retrofit project can be more effective by increasing the scope and combining other new plant equipment with the upgrade such as new tower components. In some cases, the type of mist eliminators can be upgraded from impaction type (velocity dependent) to Brownian diffusion type (velocity independent) if additional downstream protection or reduced emissions are desirable, especially at turndown rates. Trade-offs between different fibre bed types and styles are discussed as they relate to performance and maintenance.

Jan 1, 2007

By T. Orupold

This paper covers the commercial development of gravity separation of fine particles using a Lamella High Shear Rate REFLUX? Classifier (REFLUX? Classifier), focusing primarily on coal applications. The REFLUX? Classifier is a fluidized bed device that incorporates a system of closely spaced parallel inclined channels located above the fluidized bed. These channels make it possible to achieve a significant suppression of the effects of particle size, resulting in a highly effective separation on the basis of density. The improved gravity separation performance is shown to be remarkably high, with a significant reduction in the variation of separation density with particle size, and a significant reduction in the change in Ecart probable error (Ep) with size. The first full commercial-sized units of the REFLUX? Classifier were field-tested in late 2009 in coal applications. More recently, the technology has been applied in fine particle separation in minerals applications and there are a number of full-sized units operating in chrome applications in South Africa. Initially, pilot-scaled units (typically the RC?300) were trialled in iron ore, mineral sands, and manganese plants amongst other minerals, typically after other technologies failed to achieve the desired results. Currently a number of laboratories globally are carrying out more testing in minerals applications. More than 50 RC? units are now operating in coal and minerals applications. This paper introduces the REFLUX? Classifier technology, identifies commercial applications, and gives some commercial results.

Jan 1, 2014

By M. J. Sapko

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL's Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal's ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

Jan 1, 2003

By E. J. McLean

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007

By W. J. Kempson

As a result of the rising electrical energy costs in South Africa, a method was sought to reduce the overall electrical consumption of typical shaft systems. A typical shaft configuration was analysed and the primary energy consumers were identified. The ventilation fans for this system were found to consume 15% of the total energy of the shaft system. It was calculated that more than 50% of this energy is consumed by the shaft itself, more specifically, by the pressure losses that occur in the shaft as the ventilation air passes through it. In order to ensure that the theory being used for the evaluation of these shaft systems is accurate, a total of five shafts were instrumented and the actual pressure losses over the shafts plotted against time. These shafts were then analysed from a theoretical perspective. Finally, in order to ensure a thorough understanding of the behaviour of the ventilation air in shaft systems, the systems were simulated using computational fluid dynamics (CFD) techniques. There were significant discrepancies between the theoretical analysis and the CFD simulation during the initial comparisons. This discrepancy lessened as the complexity of the CFD models increased, until when the complete shaft was modelled using the full bunton sets, the pipes, and the flanges, the difference between the theoretical evaluation and the CFD simulation was small. This result demonstrates that the theory is insufficient and that the interrelated effect of the buntons and fittings has not been fully appreciated by current theory. The final phase of the work presented here was to evaluate the costeffectiveness of using different bunton shapes and shaft configurations. It is shown that the increase in the pressure losses and therefore the direct operating costs of the shaft can vary by as much as 80%, depending on the bunton configuration chosen. The placement of the piping in the shaft can increase the pressure losses, and therefore the direct operating costs of the shaft, by as much as 12%, depending on the placement of the piping in the shaft; this effect includes the use of flanges. The use of fairings on a large cage can reduce the resistance that the cage offers to the ventilation flow by as much as 30%. This, however, does not translate into a direct saving because as the cage moves through the shaft, the overall effect is transitory. These savings can be significant when the items highlighted in this work are applied correctly. Keywords shaft design, ventilation, energy consumption, modelling, CFD.

Dec 1, 2013

By K. H. Berget, V. Andersen, H. Tveit, R. Jensen

This paper presents some of the work carried out in order to improve the tapping process in silicon production, with special focus on the environmental and the safety standards. Some of the modelling work that has been done to improve the understanding of the process is described, together with the resulting implementation to improve tapping standards.

Jan 1, 2014

The proper understanding of the functioning of ground support under dynamic loading and the current approaches to designing of dynamic support are plagued by a great deal of uncertainty and lack of knowledge. This applies equally to the understanding of the support capacity as well as the demand placed onto the support due to dynamic loading. This lack of understanding currently leads to a case of design indeterminacy. This paper does not aim to solve this problem of design indeterminacy but to explore some of the issues that need consideration to obtain a better understanding of the dynamic demand on ground support systems. Keywords ground support, dynamic loading.

Dec 1, 2013

By C. -J. Rick

The ferroalloy market is characterized by a very long communication distance between the consumer and the producer. This has created a situation where it has been difficult to change ferroalloy properties. In this paper different FeNi and FeCr-compositions are discussed and their merits for stainless steel-makers in different situations are compared using the process models applied at Outokumpus Avesta works and Acerinox's Columbus operation Keywords Ferroalloy design, ferrochrome, ferronickel, stainless steel making, UTCAS software.

Jan 1, 2010

By K. A. Moxham

The ARM 1100 was described in a paper presented at the 6th International Symposium on Mine Mechanization and Automation in September 2001. It started operation underground at Rowland Shaft in early 2002. This paper covers the results of those trials that resulted in more than 1 100square metres of UG2 being mined.

Jan 1, 2004

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

When designing coal mine roof support, it is necessary to account for the uncertainties and variability that inherently exist within the rock mass and support elements. The performance of a support system is affected by these uncertainties, which are not taken into account in the current deterministic design methodologies used in South Africa. The key to the design of a roof support system is a better understanding of roof behaviour and uncertainties that can been countered during extraction. This paper sets out to develop a method that takes all uncertainties that exist within the rock mass and the mining process into account and provides a quantitative risk-based design methodology.

Jan 1, 2009

By V. Léveillé

As new legislation drives metallurgical plants to lower SO2 emissions, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost-effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an a mine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 by-product stream, which can then be directed to the front end of a sulphuric acid plant for conversion to sulphuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulphuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature, SO2 emissions in the treated gas can be controlled to as low as 55mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System, as well as which features and cost advantages for the treatment of smelter gases were important in the technology choice.

Jan 1, 2009

The depletion of favourably located and higher-grade mineral deposits, combined with more favourable metal prices and higher capital costs, has stimulated research into heap leaching of lower grade ores and wastes. This has resulted in renewed interest in heap leaching of uranium ores, and in the development of processes for the bacterial heap leaching of low-grade chalcopyrite ores and the acid heap leaching of nickel laterites. A complete programme of heap leach testwork typically involves a sequence of bottle roll tests and column tests, followed by piloting on test heaps. The initial testwork is aimed at determining the amenability of the ore to heap leaching, which depends on the characteristic of the ore with respect to porosity and permeability to leach liquor, acid consumption, metal recovery and percolation. Subsequent phases of the testwork focus on the development of the process design criteria for the treatment of the ore. Basic techno-economic models have also been developed as a tool for the initial estimation of heap leach viability. Mintek has also developed in-heap monitoring probes, coupled to an operator guidance system, in order to assist the operator in achieving optimal conditions for bacterial growth and heat preservation during pilot-plant operation.

Jan 1, 2009

By A. W. Sundström

This paper reviews the development and suitability of various important thermophysical and electrical properties with respect to base metal mattes. Areas of focus include the critical validation of measurements of viscosity, density, surface and interfacial tension, electrical conductivity, and an overview of the various experimental methods used to determine these properties. Accurate physical property data of mattes are critical in process modelling and computational fluid dynamic modelling of smelting and converting operations employed in the extraction of copper, nickel, cobalt and platinum group metals.

Jan 1, 2008

By K, J. MAUNDERS

This paper briefly describes a computerised model of the South African electricity system which has been developed jointly by the Atomic Energy Board and the Electricity Supply Commission. The results of an analysis of this system have been subjected to a fairly extensive sensitivity analysis which reveals that up to the year 1990 between 680 and 700 million tons of coal will be required for electric power generation, together with between 7 000 and 10 000 tons of uranium. This result is fairly insensitive to data variations, but the prediction of a cumulative requirement up to the year 2000, of between 1 300 and 1 800 million tons of coal and 25 000 to 70 000 tons of uranium, proves to be very data-sensitive.

Jan 1, 2014

By Willem J. Marais

The management of unpaved mine road networks on large surface mines rarely results in optimal road maintenance strategies and minimised total road-user costs. This is ascribed mostly to the complex and dynamic combination of variable road networks and loading and discharge points. In a dynamic mining environment - typically those mines in which production is managed by a centralised truck dispatch system ? there is no guarantee that a particular road maintenance intervention will contribute significantly to reducing total road-user costs or increasing productivity. Most large surface mines operating ultra-heavy mine trucks rely on an integrated on-board diagnostic data collation, communication and GPS-asset location system as a real-time fleet management tool. By extending this system to incorporate a multi-sensor analytical procedure in which specific truck vital signs are monitored and filtered, a road defect can be recognised and a trigger level set to relay the location of defects on the mine haul road to the centralised truck data management system. Previous work established the feasibility of the multi-sensor approach to road defect recognition on large mine haul trucks, and outlined the defect recognition, analytical and modelling issues and system limitations. This paper presents the development of the analytical procedure used as a basis for evaluating the truck on-board data to establish maintenance priorities amongst a network of mine roads. Following an introduction to the system architecture, the results of system field trials are analysed and the results discussed in the light of defect density and traffic volume as the primary variables in an approach to prioritising road maintenance. The paper concludes that by supplementing the existing mine communication and asset management systems, road maintenance can be managed on a near real-time basis and maintenance equipment dispatched to where most immediate benefit will realised from a maintenance intervention on the network, thereby generating the maximum improvement in service and reduction in cost per ton hauled.

Jan 1, 2008

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By M. Yavuz

Determining the most convenient plant location is one of the most commonly encountered problems in engineering applications. This paper presents a fuzzy multiple attribute decision making (FMADM) model which is developed for the selection of the optimum plant location for natural stone factories in the mining industry. The criteria affecting the decision making process in natural stone industry were determined to solve the plant location problem in the FMADM model. To determine the optimum plant location for a new natural stone factory, which is planned to be established by a mining firm located in the Eskisehir region of Turkey, an analysis was carried out by incorporating the method and the analytic hierarchy process (AHP) method. The analysis shows that the Yager?s method can easily be applied to the selection of plant location in the natural stone and mining industry when the difficulties encountered in the application process of the AHP method is taken into account. Keywords: Natural stone, plant location, decision making, Yager?s method, analytic hierarchy process (AHP).

Jan 1, 2008

By K. Andres

This paper presents the vibrating mill technology and summarizes the grinding principle of ultra fine grinding. In addition, a variety of operations is described and the benefits of these different operating modes? product size and efficiency are specified. A case study of an industrial application is presented to show the integration of vibrating mills into grinding circuits. The primary focus is the overall process scheme of this technology, the installation and operating costs, as well as the design parameters required for best performance. The vibrating mill can be used in a wide range of applications for process engineering duties. For a wide range of applications, from soft to extremely hard products, which require ultra fine grinding, surface activation or homogenization, the vibrating mill is well proven. Due to its easy operation, versatility and operation efficiency, the PALLA? vibrating mill gains in importance in the mineral processing industry. Keywords: Coal, comminution, grinding, mineral processing

Jan 1, 2010