Search Documents

By Hannweg L. A.

In a first for the diamond industry, Koffiefontein Mine in the Free State, South Africa, opted for the front cave mining method to extract a 90 metre high block of kimberlite ore. Block caving, because of its high initial capital requirements, resulting in a negative internal rate of return (IRR),was ruled out as a feasible mining method for Koffiefontein Mine. Front caving is essentially a combination of the traditional block cave and sub-level cave mining methods, but uses two or more levels of retreating drawpoints. Two extraction levels, in the case of Koffiefontein Mine, are spaced 12 m apart vertically, with the upper 478 m level (48Level) acting as the undercut/extraction level, and the lower 490 m level (49 Level) as the extraction level. Caving is achieved by undercutting a small column of ore, which is then drawn, on both the 48 and 49 Levels, until the planned extraction percentage is achieved. The next column of ore is then mined by advancing the undercut (48 Level), and the process is repeated until the entire ore block is depleted to the contact. Caving-by-gravity techniques of mining rely on closely controlled draw of the caved ore to ensure proper caving action and to minimize the dilution of ore with waste material from the open pit. This paper discusses the need for, and implementation of, a draw control system at Koffiefontein Mine — a computerized production management system, and a draw control system based on linear programming, to allow control over the draw rate and mining sequence — a major factor in all production planning to optimize production efficiency, ore recovery and cave management. Keywords: Draw control, Koffiefontein Mine, Front cave, Caving

Sep 1, 2001

Professor R. N. Pryor, AR.S.M., B.8c., C.Eng., F.I.C.E., F.I.Min.E., F.I.M.M., who died on 14th July, 1979, after a short illness, was President of the Institution of Mining and Metallurgy for the session 1978-1979. Weld pool metallurgy A high level of current interest in welding characteristics and behaviour and in the properties of welds was amply demonstrated by the large attendance at The Welding Institute's 1978 Conference on 'Trends in Steels and Consumables for Welding' and by the overwhelming number of papers offered for the International Conference on 'Arc Physics and Weld Pool Behaviour' in May 1979. Mine ventilation The First International Mine Ventilation Congress was held in September, 1975, in Johannesburg, South Africa, at the University of the Witwatersrand. It was organized by the Mine Ventilation Society of South Africa. Occupational accidents and diseases The IXth World Congress on the Prevention of Occupational Accidents and Diseases will be held in Amsterdam from 6th to 9th May, 1980. Rock mechanics The 21st U.S. Symposium on Rock Mechanics is to be held at Rolla, Missouri, from 27th to 30th May, 1980. Protection against noise An International Symposium on the Protection of Workers Against Noisewill be held in Dresden (German Democratic Republic) from 27th to 30th November, 1979. Management of mineral resources A joint meeting of the Institution of Mining and Metallurgy, the Society of Mining Engineers of AIME, and the Metallurgical Society of AIME is to be held in London from 27th to 30th May, 1980. INFACON 80 During 1970 various South African institutes and associations agreed to organize an international ferroalloys congress. It was recommended that this should be made a continuing forum, where ferroalloy people could meet and discuss matters of mutal interest.

Jan 1, 1979

By C Smit

SYNOPSIS A prototype collimated radiometric face scanner was tested in the Harmony Gold Mine. The results obtained during the pilot study indicate that in situ radiometric uranium assays are statistically indistinguishable from those obtained conventionally from channel chip samples. In addition, the study demonstrated that reasonably reliable gold estimates can be deduced from the radiometric measurements, by use of the ratio of gold to uranium within a mine. The instrumentation, calibration procedures, and background determination are described briefly.

Jan 1, 1985

By J. Pelders, F. Magweregwede, S. M. Rupprecht

Increased depths of conventional gold and platinum mines, longer travelling times as working places move further from the shaft, and ancillary activities taking place in the mining cycle reduce the useable time spent at them workface. Current shift lengths of 8 hours 20 minutes may no longer be adequate ton complete required mining activities.The impact of mineworker commuting times on shift work is also not well understood. The aim of this research was to draft a framework to optimize shift cycles in order to maximize productivity, health, safety, and wellness in the South African mining sector. The framework was informed by a review of the literature, case studies at a local gold mine and platinum mine, and a workshop with industry experts. The findings indicate potential advantages of extended shift lengths and continuous operations, such as improved productivity, asset utilization, and employee morale. However, concerns included fatigue and the associated safety hazards, particularly when working longer shifts, night shifts, and numerous consecutive shifts. Job demands, personal factors, and commuting times are further considerations when scheduling shifts. The ideal shift system for the mining sector should holistically consider and balance operational requirements, health and safety, and employees’ and their families’ requirements, and suit the unique needs of each operation. Changes in shift cycles will require a structured change management process, which involves all stakeholders, and could help to enhance the viability of the South African mining sector.

Aug 1, 2021

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By J. P. T. Kapusta

"The copper smelting industry faces increasingly stringent environmental regulations and must continue driving innovation to reduce energy usage in its production chain. With the coming of age of ‘bottom-blowing’ copper technologies in China over the last decade, much renewed attention has been brought to tuyere bath smelting for clean copper-making. Since bottom-blowing sonic injection was originally developed and implemented in steelmaking in the 1970s and lead smelting in the 1990s, the time seems appropriate to revisit the sonic injection concepts and dispel some myths. After reviewing the trends in the copper industry and providing a brief historical context of research and development related to sonic injection, the author presents a comparison of the main submerged tuyere bath smelting technologies, namely the Noranda Reactor (NR), the Teniente Converter (TC), and the Chinese Bottom-Blowing Smelting Furnace (SKS/BBS) for copper, and the Queneau-Schuhmann-Lurgi Reactor (QSL) for lead. The core of this article, however, consists of a brief description of the fundamental theories for sonic injection (jetting regime) and ‘sonic flow mapping’ to illustrate the relationship between the minimum tuyere back-pressure required to achieve sonic flow and the tuyere internal diameter. The article also offers a comparison between side- and bottom-blowing in jetting regime before concluding with the author’s vision of the new trend in submerged tuyere bath smelting. IntroductionIn the last decade, developments in the copper smelting industry have been driven by two key concepts: (1) increasing cleaner smelting capacity to meet the world’s growing copper demand, as illustrated in Figure 1, and (2) increasing process off-gas capture to comply with more stringent environmental regulations and abide by a corporate social responsibility ethic of a clean work environment (for smelter employees) and clean air (for families living around smelters). The copper smelting industry has also faced some major challenges in the last few decades, including (1) low treatment and refining charges (TC/RC or processing fees) impacting custom smelters, (2) lower concentrate quality and grades with higher levels of impurities (e.g. As and Hg), (3) higher processing and transportation costs due to the rising cost of energy, (4) restrictions in process intensification (tonnage oxygen usage) due to furnace integrity limits, and (5) scarcity of educated and trained personnel due to fewer metallurgists graduating from pyrometallurgical school programmes combined with a high retirement rate of skilled workers."

Nov 1, 2018

Advanced process and equipment analytics have been around for a while. However, with accessible IT infrastructure and site maturity, it is possible to analyse, monitor, and control processing plants and equipment easily. These various disparate systems provide different reports requiring the involvement of various personnel and attention to different reporting platforms. For efficient harnessing of the systems? capabilities, as well as effective improvement and monitoring of process and equipment, a single point of entry is required. A process and equipment optimization solution was required at a concentrator in South Africa, focussing on the product stream of platinum group metal (PGM) concentrate from the UG2 Reef. The investigation of data to identify strategies for optimization was required to allow visibility into plant operations to guide operators, an easier method to identify process loop problems, identification of imminent equipment failures, and advanced process control to optimize throughput and stability. A collaborative effort between the client and General Electric Intelligent Platforms (GEIP) investigated data-driven solutions to each of the problems. With the focus on process optimization and asset monitoring, as well as equipment monitoring, a combination of approaches was utilized to address the various problem areas that were identified. Each was implemented separately in the control layer of the plant IT infrastructure. The integration was done in a centralized web-based reporting tool that integrated the detailed results from the various solutions. On the process control side, monitoring of control loops was included by calculating performance statistics that were reported daily to identify sub-optimally performing control loops and indicating potential problems. The advanced process control solution for this site includes a surge tank controller, stabilizing flow through the flotation banks, and preventing the surge tank from overflowing or running empty. Equipment monitoring was investigated, for preventative maintenance, by making use of statistical data models to indicate imminent equipment failure. These predicted alarm events included the cause for failure, drilling down, and allowing focus on a specific variable for preventative action. The results included a more stable flow through the mill, with fewer stoppages due to surge tank overflows or running empty. The causes for process drift could be identified and operators could react early. Alarms warning of equipment failure 2½ and 4 months in advance were identified in an offline analysis.

Jan 1, 2012

"Chairman: Professor H. S. SICHEL Rapporteur: Miss M. I. WATSONPapers:Unrolling of Copperbelt orebodies by J. H. E. Perry and V. H. WiikAn exploration model for tabular orebodies by G. S. Koch and R. F. LinkHarmonic analysis of copper and gold occurrences in the Arbitibi area of the Canadian Shield by F. P. Agterberg and A. G. FabbriMathematical models of orebodies by M. J. Newton and A. G. Royle Estimation of lateritic-type orebodies by A. JournelIn his presentation Mr Wiik said that unrolling could be regarded as a reversal of the natural process of folding, so that the aim of an unrolling procedure would be the reconstruction of original pre-tectonic conditions. While simply formulated, this aim might not always be achieved. The geometrical relationship between points on the deformed surface and corresponding points on the original surface is process-dependent, and a true reconstruction could be achieved only if the deformation history were known in detail.In this computer unrolling procedure all these complexities were ignored. Referring to one particular marker horizon, Mr Wiik said that it was assumed in the procedure that this marker was deposited as a horizontal stratum and that it had subsequently been deformed by simple flexure-type folding.The procedure allowed the geologist to incorporate his knowledge and conception of the deposit through repeated re-contouring with dummy points. This 'manumatic' aspect of the procedure had proved invaluable, not only in resolving specific unrolling problems but also in making the system more acceptable to the geologists in general.Unrolling served towards removing what might be termed `tectonic noise' superimposed on the primary distribution patterns for regionalized variables such as metal content and orebody thickness. From this point of view, variograms derived on the basis of unrolled-plan co-ordinates should be more meaningful in terms of depositional environment than are variograms calculated from a normal map projection.Mr M. M. Oosterveld remarked that it appeared from the paper that there were problems in applying the unrolling technique to ore reserve calculation, and asked whether there were not other methods that might be used for that purpose.Mr Wiik replied that at present unrolling played only a minor role in practical ore reserve estimation within Roan Consolidated Mines, Limited. The techniques currently in use differed from one orebody to another, but in general they involved projection onto a vertical longitudinal section or a horizontal plan, with subsequent grid interpolation by means of a standard computer contouring package."

Jan 1, 2014

By L. A. Cornish, J. W. van der Merwe

"The hydrofluoric acid (HF) industry in South Africa uses normalized mild steel (SA 516 Gr 70) for the storage and distribution of its technical-grade product (70% HF). The technical-grade acid is split from the anhydrous hydrogen fluoride (AHF) product during distillation just after HF is produced, in a stainless-steel-lined kiln, from the reaction of calcium fluoride (CaF2) with sulphuric acid (H2SO4). Uniform corrosion of the storage tanks is mitigated during commissioning by contacting the steel with 70% HF. A corrosive reaction takes place (2H+ + 2F- + Fe - H2 + FeF2) to form scale inside the tank which diminishes the attack of the steel by fresh HF, thus prolonging the service life expectancy of the vessels. This iron fluoride scale in the vessel grows continually, resulting in corrosion of the vessels continuing at a predictable rate (approx.0.5 mm/a) since the first commissioning of the tanks at Necsa in 1993. In early 2012, an increase in the average corrosion rate of the tanks to 3 mm/a measured at and below the liquid band in the storage vessels was noted. Three months later the corrosion rate had increased to 30 mm/a, just before the first leak from the tank was detected. The tanks were decommissioned shortly afterwards and an investigation revealed that the rapid corrosion was due to the presence of increased levels (>50 ppm) of nitric acid (HNO3) in the tanks, which attacked the fluoride layer protecting the steel.The oxidation characteristics of high concentrations of HNO3 with low concentrations of HF on stainless steel surface treatment are well documented. The effects of low levels of nitric acid on the corrosion of steels in sulphuric acid are also known, but no suitable published data currently exists on corrosion by high HF concentrations with low HNO3 concentrations. Establishing the rate and mechanism of corrosion by HNO3 (0.1 to 1%) in 70% HF is currently a high priority for the HF industry in South Africa and will become increasingly important in the near future due to depleting fluorite reserves and cheaper, but less efficient, processes producing H2SO4 with higher impurity levels, which were not anticipated in the original plant design. The aim of this study is to simulate the corrosion conditions in the plant on a laboratory scale in order to establish the corrosion characteristics of the steels used in the HF plant, which are increasingly exposed to the HNO3 impurities that tend to concentrate in the final technical-grade HF acid product."

Jan 1, 2016

By F. Sundqvist, B. Skawina, J. Greberg, A. Salama, M. Astrand, P. Ekbeck

Today’s mining operations require fast reporting and rapid rescheduling based on updated information. An automatic mine scheduling system could not only quickly reschedule but also propose alternative solutions. To avoid the financial and physical risks associated with testing such a system directly in operation, it could be first evaluated via discrete event simulation models. This would offer a safe environment to evaluate different operating rules and algorithms. In this study, this is achieved by integrating automatic scheduling software with a discrete event simulation model.

Jun 1, 2021

YEAR 1943-1944 Vol. 44 Page A major change-over in the ventilation of a deep level mine, by F. G. Hill and E. C. Ranson, 27; Discussion 56, 62, 67, 71, 72, 79, 123, 129 131 A note on the quarrying of surface limestone in the Sinai Desert, by V. L. Bosazza.. .. 59 Mining with diamond drills at the Nkana Mine of the Rhokana Corporation, Limited, Northern Rhodesia, by W. A. Odgers and A. G. Stirling, 95; Discussion 117, 121, 122 123 On silicates and dusts from the Witwatersrand gold mines (some preliminary notes), by J. J. Frankel, 169; Discussion .. 178 Presidential Address-Review of the rock pressure problem, by C. Biccard Jeppe, 3; Discussion 11,15 17 The chemistry, production and application of plastics, by P. N. Lategan, 138; Discussion 151 153 YEAR 1944-1945 Vol. 45 Page A microtechnique for the size-grading of mine dust, by S. R. Rabson, 34; Discussion 49, 50, 52 55 Activated carbon for regenerating used lubricating oil, by F. J. Tromp and J. J. Matthee 90 A contribution to the study of the production of zeolites, by C. C. le Grange and A. J. Petrick 235 A laboratory method for the determination of the suitability of South African coal and coal blends for the manufacture of metallurgical coke, by R. F. J. Teichmann .. .. 202 Copper containing cements for self-sanitising surfaces, by R. S. Young and H. L. Talbot 156 Notes on some sulphide minerals from the Far East Rand, by E. Mendelssohn, 84; Discussion, 88 89 Presidential Address-A review of underground support on the Witwatersrand with its Bearing on the Problem of ultradeep mining, by P. J. Louis Bok, 3; Discussion, 24, 25 27 Scientific management with particular application to a Witwatersrand gold mine, by J. S. Ford, 63; Discussion, 77, 80, 82 83 Some aspects of rock-drilling practice (the Witwatersrand gold field), by C. J. Irving, 163; Discussion, 185, 190 *197 Temperature measurements in a mine on the Witwatersrand with an electrical resistance thermometer, by O. Weiss, 127; Discussion, 136 137 The measurement of the geo-thermic gradient by means of the clinical thermometer, by R. A. H. Flugge-de Smidt, 105; Discussion, 136 137 The micro-chemical determination of free and combined silica in mine dust, by S. R. Rabson, 43; Discussion, 49, 50, 52 55 The oxidation of pyrites associated with South African coals, by R. F. J. Teichmann 141 YEAR 1945-1946 Vol. 46 Page Air cooling plant, No. 4 Shaft, City Deep, Limited. A review of layout and results achieved, by H. W. Unwin, A. Malcolm and R. E. Campbell Pitt, 66; Discussion, 100, 102, 103, 106, 110 115 A preliminary note on the Waterberg coal field as a possible source of coking coal, by P. E. Hall 124

By C. Karageorgos, J. Sakala, A. Prinsloo, B. Ngambi

The sulphide flotation circuit at First Quantum Minerals’ Kansanshi mine in Zambia produced over 100,000 t of copper in 2019. For this circuit, mineralogical analysis has shown that the majority of the copper lost is hosted in fine liberated chalcopyrite, which is a paramagnetic mineral. The objective of this work was therefore to improve fine chalcopyrite recovery in the sulphide flotation circuit at Kansanshi, using a magnetic conditioning technology to agglomerate fine paramagnetic minerals. This theoretically increases the probability of attachment during collision and therefore improves recovery. A four-month paired ‘t’ test plant trial was carried out and comprised of consecutive ON-OFF periods with and without magnetic conditioning in the rougher flotation bank of the sulphide circuit. The experimental design involved assessment of recovery by size based on daily and weekly composite samples of feed and tails, sized using both wet-screening and cyclosizer. Both the daily plant data and the sized samples showed an increase in Cu recovery with magnetic conditioning ON. A 0.56% copper recovery improvement was measured with magnetic conditioning at a 99.4% confidence level. Keywords: Flotation, fine mineral, chalcopyrite, magnetic aggregation

Jan 1, 2020

By D. F. Malan, T. E. Oates

A recent experimental pillar extraction project at a UG2 bord-and-pillar mine presented a unique opportunity to compile a new pillar database. Currently, the South African hard rock bordand- pillar mines are designed using the Hedley and Grant formula with a modified K-value. This empirically derived formula was developed for uranium mines in the Elliot Lake district of Canada. The use of this formula for the design of pillars in South Africa is questionable. Very few pillar failures have nevertheless been observed and its current calibrations for the various reef types are possibly too conservative. A new UG2 pillar database of 66 pillars, of which seven are classified as failed, was compiled by the authors. This enabled a revised ‘first-order’ calibration of the K-value for the Hedley and Grant formula. The new estimated value for the UG2 is K = 75 MPa. This gives a pillar strength that is more conservative than the PlatMine formula. This work should nevertheless be considered as only a preliminary calibration as the database was small. Further work is also required to determine whether the exponents in the formula for the width and height parameters are appropriate for UG2 pillars.

May 3, 2023

By P. J. D. Lloyd, Jill Urban, M. R. Urban

The adsorption of gold from cyanide solutions onto constituents of the reef, and its role in reducing the efficiency of the gold-recovery process by M. R. URBAN. M.Sc. (Chem. Eng.) Rand (Visitor). JILL URBAN. B.Sc. (Chem. Eng.) Rand (Visitor) and P. J. D. LLOYD. Ph.D. (Cape Town) (Fellow) Evidence for the adsorption or re-precipitation of gold from cyanide solutions onto gangue minerals of the Witwatersrand reefs has been gathered over a number of years by various investigators. The evidence from tests using radioactive tracers is conclusive and indicates thlt adsorption contributes about 0,1 g/t to the total gold loss from conventional reduction works. The loss is a function of the alkalinity and cyanide concentration of the solution, and it appears to be affected by the extent of time between milling and cyanidation. The heavy minerals appear to be the strongest adsorbers, and the clay minerals somewhat less strong adsorbers. A sensitive qualitative test based on thin-layer chromatography permits the extent of adsorption and desorption to be readily determined.

By L. A. Vermeulen, D. D. Howat

A study was made of the performance of a rod mil operating without liter bars and with different arrangements of liter bars in the lining. . The results show that striking improvements in performance, increased throughput, and reduced consumption of liner metal and electrical energy can be obtained by a change in the geometry of the liter-bar arrangements within a mil. Rod mils of equal size fitted with the same arrangement of liter bars but operating at different speeds presented apparent anomalies in the relative consumption efficiency of electrical energy for the production of material smaller than 75 µ m. Marked savings in the consumption of liner metal were achieved by the use of an arrangement of alternating lines of higher and lower liter bars. A study of the relative performances of two large tube mils showed that the use of liter bars in one of the mils resulted in a marked reduction in the consumption of liner metal and electrical energy per ton of material smaller than 75 µ m in the product.

Jan 1, 1986

By H. Dudycz, A. Skoczylas, P. Stefaniak, P. Pyda

In the era of Industry 4.0, technologies such as Big Data (BD) and the Internet of Things (IoT) play a key role, especially for multi-site manufacturing companies. In such companies, the challenge is to collect and process massive amounts of data from industrial devices and extract key information from this data in real-time for ad hoc decision-making. The ability to analyse data from industrial devices translates directly into streamlined production processes, cost optimisation, prevention of unplanned events, and safety during operation. In this context, particular attention should be paid to Big Data Analytics (BDA), whose main source is the Industrial Internet of Things (IIoT). The purpose of this paper is to propose an IT system architecture incorporating BD and the IoT for a mining company. The paper presents results from a literature review focusing on available BD and the IoT solutions for industry (mining in particular) for the purposes of the acquisition, integration, and advanced analysis of data. The advantages and disadvantages of the different solutions were indicated and gaps in the accessibility to dedicated functionality are identified. Based on the analysis of a multi-site mining company, the main challenges faced by such companies planning to implement BD and IoT solutions are identified. Also, a proposal for an IT system architecture incorporating BD and IoT for a mining company is described in the paper. The contribution of the article consists of the identification of the challenges faced by mining companies planning to implement BD and the IoT solutions, and the proposal of an IT system architecture that allows BDA whose main source is the IIoT.

Sep 1, 2021

Underground operators' conference. Parkvile (Australia), Australasian Institute of Mining and Metallurgy, $A25 (surface). Reviewer: G.R. Stil Reagents in the minerals industry: A review, edited by M.J. Jones and R. Oblat. London, Institution of Mining and Metallurgy, 1986, £50. Reviewer: L. Goold

Jan 1, 1986

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The influence of two weeks of microclimate cooling on the state of heat acclimatization by N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, M.Sc. (Potch.) (Visitor), and W. H. VAN DER WALT, B.Sc. (Potch.) (Visitor) Five volunteer Black subjects were acclimatized according to the climatic-room acclimatization procedure, and their states of heat acclimatization were determined by the usual heat-stress test. The subjects thereafter wore pre-frozen jackets in a somewhat higher environmental temperature (33,9/35,6 °C). stepping at the same rate as before for four hours a day for fourteen days. The heat-stress test was repeated and followed by a similar test at the higher environmental temperature. It was found that fourteen days of microclimate cooling in a very hot environment had no adverse effect on the degree of heat acclimatization. The sweat rates during microclimate cooling remained high, even though no sweating is possible beneath the pre-frozen ice-jacket. which indicates that there is an increase in sweat rate from the areas of exposed skin.

Jan 7, 1975

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020

By C. J. Lenz

The results of prospecting operations involving geological data and a large number of geochemical determinations of the metal content of soil samples are plotted and evaluated by computer. Anomalous areas are identified in each type of environment by selecting probability or population boundary values from frequency distributions. The anomalies are plotted to permit correlation with geographical or geological features. Ranking of prospecting targets is made using geographic pattern, geology, absolute value and metal ratios. Three short case histories are presented.

Jan 1, 2014