Search Documents

By Q. G. Reynolds

Keywords: Pyrometallurgy, furnace, DC, reverse polarity, dual-electrode The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode, and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions ? this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magneto-hydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By F. X. Prins, L. R. Nelson

Tight control of electrode paste additions, hard and soft paste levels, baked zone position and electrode temperatures are integral to superior Söderberg electrode management practices. Paste addition is typically effected through briquettes, cylinders or large blocks. Each electrode paste form has its advantages and disadvantages, but probably a more crucial element from an electrode control perspective is the frequency and amount of electrode paste addition into a Söderberg electrode column. The detrimental effects of excessive soft paste levels leading to Stokes? Law segregation of paste in the electrode column are well documented, while several operators have effectively implemented the use of electrode thermocouples to monitor paste temperatures and automated slipping algorithms to control baking conditions within electrodes. Somewhat less well appreciated are the negative influences of inadequate soft paste levels, especially when coupled with excessive paste cylinder or block additions and resulting high hard paste levels. The alternative of insufficient hard paste levels and associated overheated electrode paste must also be considered, and can contribute to paste segregation directly. This condition also has the potential to generate gas mixtures in the electrode column that are concurrently a potential health hazard, while being prone to spontaneous combustion. Results of industrial trials on electric furnaces using Söderberg electrodes in a variety of applications from ferrochromium, to ferromanganese and even platinum-bearing base metal sulphides smelting are presented to illustrate the influence of paste loading practices on the dynamics of hard and soft paste levels. Possible electrode failure mechanisms attributable to inadequate paste level control will be discussed through some industrial examples. Suitable paste loading practices to mitigate the risks of inappropriate paste levels and associated electrode incidents are presented.

Jan 1, 2004

By Z. L. Xue, J. L. Li, X. Y. Wang

"In low-carbon energy-efficient basic oxygen furnace (BOF) steelmaking processes, limestone partly or completely replaces the active lime. The effects of limestone calcination temperature (1200–1500°C) and time (5–15 minutes) on lime reactivity and CaO grain size were investigated. The reactivity was evaluated by titration with hydrochloric acid, and the CaO grain size was analysed using scanning electron microscopy. The results revealed that for calcination temperatures higher than 1300°C, the reactivity reached a maximum and then decreased . The higher the temperature, the earlier the peak of reactivity appears. The CaO grains grow with increasing temperature and time, which leads to the decrease of reactivity. Notably, the effects of temperature on CaO grain size and reactivity are more marked than that of time. To obtain active lime calcined at ultra-high temperature by flash heating, the calcination conditions should be 1300–1400°C for 10–15 minutes, or 1400–1500°C for 8–10 minutes. IntroductionLime is one of the most important slag-making materials for dephosphorization and desulphurization in the basic oxygen furnace (BOF) steelmaking process. The reactivity of lime is a measure of its capability to take part in slag-making. Lime having a reactivity of more than 300.0 mL (4 N HCl), determined by hydrochloric acid titration is generally referred to as active lime (Rusjan et al., 2007; Zeman, 2008). At present, the active lime used for BOF processes comes primarily from a kiln or shaft kiln, where limestone is preheated at 700– 900°C, and then calcined at 1050–1200°C (Drenhaus et al., 2010; Oates, 2007)."

Jan 1, 2016

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By T. Nishimura, H. Kiyama, K. Wakimoto

Discussion on the load bearing capacity of ground and the stability of tunnel is presented. We derive a simplified solution of a circular lined-tunnel in an elastic ground. The solution results in a better understanding of characteristic curves. Use of DEM allows us to consider effects of possible yield of the overstressed zone around the tunnel and inherent discontinuity of ground on the curves. Diskussion auf der Last Tragfähigkeit Bodens und die Stabilität des Tunnels wird dargestellt. Wir leiten eine vereinfachte Lösung eines kreisförmigen Ausbautunnels in einem elastischen Boden ab. Die Lösung ergibt ein besseres Verständnis der Kennlinien. Um Gebrauch DEM erlaubt uns, zu betrachten Effekte des möglichen Ergebnisses der überbetonten Zone den Tunnel und zugehörige Unstimmigkeit des Bodens auf den Kurven. La discussion sur la portance de charge de la terre et de la stabilité du tunnel est présentée. Nous dérivons une solution simplifiée d'un revêtement-tunnel circulaire dans une terre élastique. La solution a comme conséquence une meilleure compréhension des courbes caractéristiques. L'utilisation de DEM nous permet de considérer des effets du rendement possible de la zone surchargée autour du tunnel et de la discontinuité inhérente de la terre sur les courbes.

Jan 1, 2003

By T. Frömmer, H. Wagner

An inter-disciplinary geotechnical study has been carried out in an Austrian magnesite mine. The paper describes the how geological data, in situ and laboratory tests as well as subjective, empirical, geophysical and numerical methods have been used to identify critical areas in the mine. In einem österreichischen Magnesit Bergbau wurde in den letzten Jahren eine interdisziplinäre geotechnische Studie durchgeführt. Der Vortrag beschreibt den Einsatz subjektiver, empirischer, geophysikalischer und numerischer Methoden zur Identifikation geotechnischer Problembereiche Ces dernières années des études géotechniques interdisciplinaires sont effectuées dans une mine souterraine de magnésite en Autriche. Ce rapport trace l’application des méthodes subjectives, empiriques, géophysiques et numériques pour identifier les zones problématiques dans la mine

Jan 1, 2003

Rock mass classification systems are extensively used in rock engineering design work, and mine design is no exception. Among the systems most widely used for mining-related design work are the NGI 0-system (Barton et al., 1974), the RMR system (Bieniawski, 1976), the MRMR system (Laubscher and Taylor, 1976) and, more recently, the GSI system (Hoek et al., 1998). Classifying the rock mass is widely seen as being the fieldwork required to characterize the rock mass and enable the application of empirical design methods associated with the different classification systems. This paper argues that it is fundamentally important to recognize the distinction between rock mass characterization and rock mass classification. These two processes should, in most cases, be separated from each other. Rock mass characterization should be used to determine the intrinsic properties of the rock mass independently of the application; i.e. independent from the infrastructure to be designed, the size, shape, and orientation of the excavation(s) or pillar(s), etc. Rock mass characterization should also be compatible with most classification systems and empirical design methods to be used. Rock mass characterization is the background fieldwork required to perform rock mass classification and/or engineering design work. Rock mass classification is the subsequent step to the characterization, and an integral part of the design process. Parameters that vary according to the design, such as the relative orientation of geological structures compared to the opening or the mine-induced stresses, should be calculated as part of the rock mass classification and design process, rather than during the rock mass characterization process. The failure to distinguish between rock mass characterization and rock mass classification can lead to major design errors and poor results.

Jan 1, 2012

By O. Leuangthong, M. Nowak

"The impact of high-grade data on resource estimation has been a longstanding topic of interest in the mining industry. Concerns related to possible over-estimation of resources in such cases have led many investigators to develop possible solutions to limit the influence of highgrade data. It is interesting to note that the risk associated with including high-grade data in estimation appears to be one of the most broadly appreciated concepts understood by the general public, and not only professionals in the resource modelling sector. Many consider grade capping or cutting as the primary approach to dealing with high-grade data; however, other methods and potentially better solutions have been proposed for different stages throughout the resource modelling workflow.This paper reviews the various methods that geomodellers have used to mitigate the impact of high-grade data on resource estimation. In particular, the methods are organized into three categories depending on the stage of the estimation workflow when they may be invoked: (1) domain determination; (2) grade capping; and (3) estimation methods and implementation. It will be emphasized in this paper that any treatment of high-grade data should not lead to undue lowering of the estimated grades, and that limiting the influence of high grades by grade capping should be considered as a last resort. A much better approach is related to domain design or invoking a proper estimation methodology. An example data-set from a gold deposit in Ontario, Canada is used to illustrate the impact of controlling high-grade data in each phase of a study. We note that the case study is by no means comprehensive; it is used to illustrate the place of each method and the manner in which it is possible to mitigate the impact of high-grade data at various stages in resource estimation."

Jan 1, 2015

By R. C. D. Phillis

Conventional stoping in hard rock mining is largely considered an operational environment. This paper suggests that stoping falls within the realm of a project management environment typified by uncertainty, variation, and large numbers of interdependencies. Stoping was then equated to a micro-project with many simultaneous activities that had to be executed accurately using finite resources within limited shift durations in order to reach specific goals. Critical chain project management (CCPM) principles were applied to the stoping activities, and the results showed that the number of blasts per panel can be significantly increased by successfully moving the distribution of work as close as possible to the start of shift. Critical chain principles also assisted in facilitating re-focusing and teamwork among stoping crews as well as between day- and night-shift crews. The main recorded success was in managing inherent protective capacities/local contingencies/fat/buffers that are found in all projects. The impact on mine health and safety (MHS) was significant as individual operators and crews became convinced that they could perform all stoping tasks (activities) without compromising accuracy or speed.

Jan 1, 2011

Experimental results are presented that test the hypothesis that the descaling behaviour of stainless steel slabs following reheating is controlled by interfacial roughening at the scale-steel interface. In this investigation, two stainless steels were considered: type 304 (austenitic, with 18% Cr and 8% Ni) and type 412 (ferritic/martensitic, with 11.6% Cr). It was found that the entanglement that arises at the scale-steel interface was in fact effective in maintaining scale-steel adhesion, under the mechanical descaling conditions used. In the case of type 304, descaling proceeded by fracture along chromite layers, which formed (by internal oxidation) on the austenite grain boundaries; for this steel, the extent of descaling depends most strongly on austenite grain structure, and not primarily on the conditions in the reheating furnace. In contrast, type 412 samples descaled only at the edge of the entangled zone, and showed a greater sensitivity to the reheating conditions; specifically, higher free oxygen in the reheating gas and longer reheating times were found to increase the residual scale thickness. Key words: stainless steel, reheating, scale, entanglement, descaling, fayalite, internal oxidation, grain structure, free oxygen.

Jan 1, 2003

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

Phase equilibria have been determined experimentally for pseudo-ternary sections of the form ?MnO?-(CaO+MgO)-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.17 and MgO/CaO weight ratios of 0.25 and 0.17 respectively for temperatures in the range 1473-1673 K. The primary phase fields present for the MgO/CaO weight ratio of 0.17 include manganosite (Mn,Mg,Ca)O; dicalcium silicate a-2(Ca,Mg,Mn)O?SiO2; merwinite 3CaO·(Mg,Mn)O·2SiO2; wollastonite [(Ca,Mg,Mn)O?SiO2]; diopside [(CaO,MgO,MnO,Al2O3)?SiO2]; tridymite (SiO2); tephroite [2(Mn,Mg)O?SiO2]; rhodonite [(Mn,Mg)O?SiO2] and melilite [2CaO?(MgO,MnO,Al2O3)?2(SiO2,Al2O3)]. For the section with MgO/CaO weight ratio of 0.25 the anorthite phase (CaO·Al2O3·2SiO2) is also present. The liquidus temperatures of ferro- and silico-manganese smelting slags have been determined. The liquidus temperatures at low MnO concentrations are shown to be principally dependent on the modified basicity weight ratio (CaO+MgO)/(SiO2+Al2O3).

Jan 1, 2004

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 um. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By T. O. Hagan

A simulated rockburst experiment was conducted underground at a deep level gold mine. This was done by means of a large explosion detonated in solid rock close to a tunnel sidewall. The resultant shake-out damage is typical of that associated with a small seismic event in close proximity to a tunnel that is subjected to the estimated field stress, as in this case, of 50 MPa. The experiment involved: ?the design of a blast to mimic a seismic source ?seismic monitoring using a dense seismic array ?high speed video filming ?a study of rock mass conditions (fractures, joints, rock strength etc.) before and after the simulation using mapping and ground penetrating radar ?special investigations to evaluate the mechanism and the magnitude of the damage ?a study of support behaviour under excessive dynamic loading.

Jan 1, 2001

By D. F. Malan, Y. Jooste

"SynopsisScattered mining was practised on Kusasalethu Mine (previously Elandsrand Gold Mine) prior to 1998, but at deeper mining levels it was no longer feasible, since it would have resulted in unacceptably high stress levels and energy release rates. Longwall mining was not adopted at these depths as the mine required a more flexible mining method owing to the highly variable grade and the presence of geological structures. A mining method was developed that consisted of dip stabilizing pillars for regional support, as well as bracket pillars to clamp geological structures. A strict sequence of extraction was followed and this, together with the particular layout, was called the ‘sequential grid mining method’. This method addressed two key problems, namely negotiating adverse geology and the erratic grade of the Ventersdorp Contact Reef (VCR) orebody. However, a significant drop in production rates resulted in the need for alternatives and improvements to the original mine design. Modifications to the design were proposed in order to increase production rates, and an investigation to consider the rock engineering implications of these modifications was conducted. The study indicated that the modified method, called the ‘multi-raise mining method’, appears to be feasible and might address some of the production problems that were experienced with the original sequential grid design. An analysis of actual seismic data showed no significant differences between the original sequential grid mining and the implemented multi-raise mining. The numerical modelling of the mining layouts showed slightly higher interim energy release rates (ERRs) and average pillar stress (APS) levels during the extraction process. The final values are nevertheless identical to that of the original sequence. The study also investigated the use of a modelled moment method to analyse future seismic trends. The study illustrated that the expected seismic trends will be very similar for the multi-raise method compared to the original sequential grid mining method. This study is nevertheless considered of a preliminary nature and ongoing monitoring and analysis of seismic data at the mine is required to verify the response of the rock mass to the modified sequence and increased extraction rate. In particular, future work needs to investigate the effect of mining rate (advance rates in individual panels as well as volume of mining in particular raise lines) on the level of seismicity."

Jan 1, 2015

By Z. W. Nkosi, M. Sephton, J. H. Potgieter

The exhaust system is a complex assembly of various components performing important tasks in harsh environments. Carbon steels have been used extensively in exhaust systems, but pressure for lower cost, increased fuel efficiency; lower hazardous emissions, weight savings and increased life expectancy have shifted the emphasis to stainless steels. In response to the growing consumption of stainless steels in automotive exhaust systems, the need to properly evaluate their corrosion resistance properties in order to ensure their appropriate use, has increased substantially. This paper evaluated the most common corrosion and oxidation tests developed that are used and applied it to four common stainless steels often employed in hot end exhaust components. In a summary considering the weight loss of an alloy, it general corrosion rate and pitting resistance under all the test conditions for hot end exhaust components, results indicate that 434 was by far the most corrosion resistant alloy, followed by 1.4509 and 321, and lastly 304 was the least corrosion resistant. In general, the ferritic stainless steels, especially 434, outperformed the austenitic ones under all the test conditions.

Jan 1, 2006