Search Documents

A project was funded by the Australian coal industry to investigate the mechanisms that might lead to sample bias when using cross-belt cutters, in order to help coal industry personnel to make better decisions about the purchase, maintenance and operation. It concentrated on DEM modelling of skew cutters. These are set at an angle to the belt with the intention of minimizing disturbance to the non-sampled material. Two bias mechanisms are likely to cause bias for cross-belt cutters. Waves of material are bulldozed off the belt by the upstream side of the body of square cutters and material is thrown by the leading edges of cutter blades for all types of cross-belt cutters. These mechanisms cause some parts of the load of material on a belt to be over-represented. The effects of these mechanisms cannot be made to be negligible, so cross-belt samplers cannot be trusted to produce unbiased samples, especially for segregated streams of material. However, it is possible to give a bound on the maximum likely bias. The grades of two portions of the stream can be estimated by stopping the belt and shovelling off 1/3 of the cross-section of the load on the belt into a container, concentrating on the final side of the belt and the top of the load. The remaining material should be put into another container and the difference in grade determined. The maximum likely bias is typically about 10% of this difference. For a cross-belt cutter, having an extraction ratio near to 100% is not a reliable indication that the cutter has little or no bias. Some bias mechanisms affecting cross-belt sample cutters make sample mass too high and some make it too low, so an extraction ratio near 100% can occur if two bias mechanisms are both active. Keywords: sampling, DEM simulation, sample bias, accuracy, precision

Jan 1, 2009

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

By J. Rabe

Tasked with developing a flow sheet for a new resource, one typically turns the experts for help. The advice of an expert can be invaluable in reducing the time and costs associated with characterizing an ore (not to mention extracting maximum information from limited samples). While guiding and optimizing a metallurgical concept study requires a certain skill set, selling a project is something different. The metallurgical specialist is usually not responsible for sharing the results of investigations with potential investors. However, the person responsible for selling the project can ensure that a metallurgical concept study is conducted thoroughly and responsibly without having the ability to do the work, while being sufficiently familiar with the metallurgical aspects to authoritatively sell the project. The process of identifying suitable process routes through to constructing a concept flow sheet and mass balance is discussed as a basic example. From basic mineralogical information and a thorough literature survey, the most likely beneficiation routes can be identified and targeted testing conducted. The final top size will depend on the required product properties (mainly grade), the selected beneficiation technology, and the ore?s liberation properties. Once the required top size has been identified, comminution options can be evaluated. Once again, literature surveys can be used to supplement concept-level comminution property information, and select possible equipment and circuit configurations. Marketing, material handling, and logistics-related information can be used to determine required dewatering technologies. At this stage, enough information is available to develop a concept mass balance and conduct basic equipment sizing..

Jan 1, 2014

By X. Ndlovu

Underground observations in a coal mine have indicated failure oft he immediate roof above the bords. Careful observations and photographic recording of occurrences of these roof failures, termed ?roof guttering?, have been made. The occurrence of guttering results directly in roof instability, and indirectly, due to the interaction of the guttering with natural planes of weaknesses in the immediate roof rock. In this paper, relevant observations of roof guttering, possible mechanisms of formation of roof gutters, laboratory testing for determination of material strength and deformation properties, and numerical analyses to explain underground observations are described. Mapping of roof failures showed that these took place mainly towards the centre of the roadways. Roof guttering was observed often to occur violently and with little warning. Occurrence of roof guttering has a negative impact on production?some panels are abandoned, production times are increased and safety of workers is compromised. The numerical stress analyses showed that, although none of the constitutive behaviour criteria used predicted the observed underground failures correctly, the extension strain criterion gave the best agreement.

Jan 1, 2007

By K. Woodward, Y. Potvin, B. McFadyen, M. Grenon

Open stoping has become a popular mining method in hard rock mines, not only due to the safety of the method as a non-entry approach, but also because of the high extraction rate and low costs. At mine sites, stope performance is evaluated by calculating stope overbreak using the stability chart. However, limitations of the stability chart regarding the precision of the predictions, nonconsideration of factors such as the influence of blasting, and the exclusion of underbreak have led to non-optimal designs. The capabilities of today's computers have increased the amount of data being collected and the power of models being built. This article presents a step towards a new stope design approach where stope overbreak and underbreak are measured and georeferenced using octrees at an approximately cubic metre resolution and predicted using multivariate statistical models (partial least square, linear discriminant analysis, and random forest). Results show that overbreak and underbreak location along the design surface and their magnitude are predicted with good precision using a random forest model. These predictions are used to build the expected geometry of the open stope. The resolution of the data and the use of multivariate analysis has enabled the prediction of variation in stope performance along the design surface, going well beyond the simple qualitative per stope face prediction provided by a traditional stability chart approach.

Jun 5, 2023

By P. Gonzalez

Minera La Parreña, S.A. de C.V., Milpillas operation is an underground mine designed to process 8 352 tons of ore per day for the recovery of copper through crushing, heap leaching, solvent extraction and electrowinning facilities. In order to optimize copper recovery during leaching, the ore is crushed to 13 mm and subjected to primary sampling every 15 minutes for metallurgical accounting. At the same particle size, primary sample goes to secondary sampling and then, the secondary sample is crushed to 2 mm before tertiary sampling. The tertiary sample is sent to laboratory where a final sample is obtained and pulverized to 106 microns for copper assay. This paper shows a review of sampling strategy focused on minimizing or eliminating sampling errors and an experiment designed to determine copper head grade profile as well as the best sampling frequency.

Jan 1, 2009

By K. -H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes become available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60%-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none-sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as uneconomic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid. Even though smelter gas is available at high SO2 concentrations, in a conventional acid plant one would add large amounts of air to dilute the gas down to a suitable concentration of 12?13 (14) %-vol. SO2. Dealing with higher SO2 concentrations in smelter acid plants is not feasible, as the gas exit temperature of the catalytic oxidation step would exceed the allowable limit for the catalyst. Hence those conventional acid plants are characterized by the use of large equipment, i.e. high capital cost, high energy consumption and limited flexibility. The newly developed LUREC® process can handle off-gas with significantly higher gas concentrations, even in excess of 25%-vol. SO2. It is entirely based on well-proven equipment and unit operations. The first industrial application, operating with 16?18%-vol. SO2 will be presented in this paper, along with the fundamentals of the process. It will be demonstrated that the process requires inherently lower capital cost, fewer operating costs, and offers better energy recovery and lower emissions as compared to conventional design. While most existing smelter acid plants would have some built-in spare capacity, any significant increase of smelter capacity, say of 30%, can basically not be accommodated without installing an additional parallel new acid plant unit. An add-on LUREC® module can remove any such restriction, while simultaneously debottlenecking the existing acid plant. The paper also discusses the present status of the add-on technology for smelter acid plant expansions with respect to technical boundary conditions of different process alternatives as well as economic and environmental aspects. Application of the LUREC® process to modern smelter acid plants operating with high SO2 gas concentration, will lead to a substantial reduction of the specific size of the gas processing equipment and equivalent savings in capital and operating cost. The LUREC® process is patented worldwide by OUTOTEC.

Jan 1, 2009

By V. Moodley

Strict implementation of International Standards for representative sampling of coal is difficult for routine monitoring, due to time, technical, and economic constraints. A large percentage of the total sampling variance arises from errors accumulated during the earliest stages of sample collection. Modified procedures on the precision of the final result leads to controversies between the sellers and customers for coal. Manual collection of coal samples violates the principle of correct sampling, that all fragments must have an equiprobable chance of being in the sample. In addition, manual size reduction of large numbers of samples is time consuming and involves human errors. A coal quality management procedure in alignment with the relevant ISO standards that describes the sampling protocol has been implemented, and current sampling and laboratory analysis of coal from base load mines (mines situated at the mouth of the power station) are well established. For import coal, sampling is performed during unloading by auto-mechanical sampling (AMS). Due to logistical and safety issues associated with multiple suppliers, Eskom opted for the coal to be sampled at source on a pre-certification basis. Online analysers provide a fast, accurate, real-time method of determining the total moisture and elemental composition of coal and is important to the coal industry for pricing, quality control, and reduction of SO2 emissions. Elemental analyses include S, Si, Al, Fe, Ca, Na, Mg, Mn, Ti, K and Cl. Measurement of S is dictated by the control of SO2 emissions from coal-fired power plants. Elements such as Na and Cl have adverse effects on boilers, causing fouling and slagging. Available online elemental analyser technologies include prompt gamma neutron activation analyses (PGNAA), recommended for major element determination, and pulsed fast and thermal neutron analysis(PFTNA), that is capable of measuring the major and minor chemical elements contained in coal. These systems utilize nuclear reactions to produce characteristic gamma rays that are used for identifying various chemical elements. By acquiring the gamma rays in three different time windows, there is a significant reduction of the background as compared with the spectra taken with a radio isotopic source.

Jan 1, 2009

Excessive dust generation from unpaved mine haul roads is a problem common to most surface mining operations. While optimal road wearing course material selection parameters reduce the inherent dust generation potential, they do not totally eliminate fugitive dust. Many different classes of suppression or palliative treatments are available for mine haul roads and this paper initially ascertains basic selection guidelines, using a set of ideal dust palliative product, application and performance parameters based on mine road-user requirements. An evaluation and modelling methodology for truck generated fugitive dust emissions is developed as a basis for the comparative assessment of dust control strategies. For water-based spraying, a watering model was developed to estimate individual mine road watering frequencies for characteristic site parameter combinations during summer and winter operating conditions, for a required level of control or maximum dust defect. This forms the base-case scenario with which to compare the performance of other types of dust palliatives under the same conditions. Finally, a basic palliative economic evaluation model is introduced with the aim of identifying and costing the establishment, application and maintenance rejuvenation activities associated with the use of chemical palliatives. While palliative cost and performance is generally site specific, it is shown that under certain combinations of conditions, the use of dust palliatives has the potential to deliver cost savings when compared to water-based spraying.

Jan 1, 2007

By А. А. Vasiliev, Y. G. Seredkin, А. V. Aksenov, А. Y. Senchenko

Refractory gold-containing concentrates usually contain gold enclosed in sulphides as well as in rock-forming minerals. Another difficulty is that gold often occurs as very fine inclusions of several micrometres, and even smaller than 1 micrometre, or can be part of the mineral composition at the structure level. Processing of such concentrates is a challenge. Ultrafine grinding and further oxidation are applied for gold liberation. The paper deals with the results from the study of gold deportment using Qemscan, and atmospheric oxidation testwork involving Albion Process™ on a gold-containing concentrate with a high content of refractory gold in sulphides and gangue minerals. Albion process testing was performed at Institute TOMS with the participation of Glencore Technology Pty Ltd (Australia). Additionally, conventional cyanidation testwork was carried out for the concentrate processing. As an alternative technology of gold liberation, oxidising roasting with arsenic stabilisation was used. The results from the study make it possible to assess the efficiency of the above-mentioned methods of gold liberation, and applicability of Albion technology to recover gold from the refractory concentrate. Key words: Gold, refractory concentrate, Albion Process, atmospheric oxidation, oxidising roasting, leaching

Jan 1, 2020

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By K. Arnold

AngloGold Ashanti has been proactive in the field of energy management for many years. AngloGold Ashanti is a signatory to South Africa?s National Energy Accord of 2005 calling for a15% reduction in energy consumption by 2015 for the mining sector. This target also supported our internal targets that were already set. AngloGold Ashanti?s seven South African mines consume on average 440 MW. Due to the dynamics of gold mines, and the large numbers of relatively small energy efficiency initiatives and awareness campaigns made measurement and verification of energy efficiency very difficult at a macro level since some initiatives could get lost in the fluctuating load profile. This paper will discuss the methodology and process followed to quantify the impacts of the combined energy efficiency initiatives at macro level. It will quantify the energy efficiency impacts in megawatt-hours (MWh), financial, and equivalent carbon emissions (CO2e) reduction with reference to our baseline year, 2004, for the Vaal River and West Wits mine clusters.

Jan 1, 2009

By E. Lwamba

The aim of this study was to examine the effect of grain size distribution control of the raw material mixture on the permeability of the green sinter bed and the properties of the produced sinter. This was achieved by evaluating the granulation characteristics of the sinter mixture (moisture content, granulation time and mean granule diameter) in terms of its green bed permeability, and evaluating the productivity of the sinter bed, the coke rate, tumble index (TI), abrasion index (AI), reduction disintegration index(RDI) and reducibility (RI) of the produced sinter. The raw sinter mixtures contained combinations of Thabazimbi iron ore, Sishen iron ore, coke, lime and return fines. The grain size distributions were controlled by removing the ?0.5 mm size fractions of the return fines and coke, and the ?1 mm size fraction of lime. Of the examined mixtures, a mixture of 20 mass% Thabazimbi iron ore, 80 mass% Sishen iron ore and fluxes where the coke, lime and return fines were all sized had the highest granulation effectiveness and permeability. The sintering properties of the mixtures in which the grain size distributions were controlled, were very similar for all the mixtures, but superior to the base case mixture in which the grain size distribution was not controlled. Keywords: Thabazimbi iron ore; Sishen iron ore; granulation, permeability, grain size distribution; sinter.

Jan 1, 2008

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By S. Kok, D. Delport, J. Calitz

Altering the microstructure in order to improve the tensile properties of bow shackles resulted in inconsistency in the fatigue performance. This raises the question whether the inconsistency in fatigue life can be attributed to microstructural changes along the profile of the shackle or to decarburization at the surface. Bow shackles forged from 080M40 (EN8) material were subjected to different heat treatments in order to alter the microstructure. The shackles were subjected to five different fatigue load cases, which represented typical loads experienced at termination points for an overhead power line with a span length of 400 m, with changes in conductor type, configuration, wind, and ice loading. Although the change in microstructure does improve both the tensile and fatigue performance, we found that the depth of the decarburization layer has a greater effect on the high cycle fatigue life of bow shackles than the non-homogeneous microstructure.

Oct 1, 2021

By G. Mucsi, F. Kristály, R. Szabó

Kaolin is one of the most important ingredients in porcelain manufacturing. Its main phase is clay mineral containing aluminum hydrosilicate, namely kaolinite. Beside kaolinite it also contains quartz, illite and feldspars, which impair its applicability. Kaolin is a non-reactive material, but metakaolin can be produced by heat treatment (calcination) of kaolin, which is also used by the cement and concrete industry due to its latent hydraulic (pozzolanic) properties. Beside thermal activation, reactive materials can also be produced by mechanochemical activation in general. This paper deals with the mechanochemical activation of kaolin. The raw material was classified into various size fractions, then ground in a batch stirred media mill under varying circumstances (residence time, circumferential velocity). After grinding, the structural changes of the products were investigated by X-ray diffractometry (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). In addition, the particle size distribution of the ground material was determined by laser scattering. As a result of the grinding experiments and analytical measurements of the products, it can be clearly seen that reactivity of kaolin can be improved significantly by mechanical activation in a stirred media mill, but due to its high energy density the circumstances were optimised carefully to avoid aggregation. Keywords: Kaolin, grinding, stirred media mill, mechanical activation, material structure

Jan 1, 2020

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By D. Kok

A challenge in mine planning is the optimal allocation of resources to the appropriate workplaces within the shift cycle (labour, equipment type, and other resources) in order to carry out the shift cycle activities, achieve planned production targets, and ultimately maximize production within all infrastructure constraints. Generally, detailed mine planning is done on a monthly basis at a workplace level in order to determine the production targets. The production supervisor, mine overseer, or equivalent production manager must then make the appropriate resource allocation trade-off decisions on a daily basis per shift to try and deliver to the plan and required production target. Due to the complexity and number of permutations of possible resource allocation decisions, it is impossible for a human brain to make the appropriate and optimal allocation decisions that will result in achieving the maximum or target production. These allocation decision permutations must deal with the current status of workplaces (availability, position in the cycle etc.), the status of equipment availability (available, planned maintenance, or breakdown etc.), distance between the workplaces (traveling time of equipment between workplaces, etc.) and equipment type required for that shift cycle activity. All these factors need to be taken into account in resource allocation to plan for the shift, and even during the shift if a major piece of equipment becomes unavailable or a workplace activity is not progressing as planned. This paper is a case study on how an optimization algorithm can be used to create a production planning system for optimization of resource allocation in a mechanized underground platinum operation. A business case for optimal allocation of resources is demonstrated and compared to the current manual planned allocation.

Jan 1, 2012

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009