Search Documents

By E H. O Meyer, K van Dyk

Fine powders normally exhibit, to a more or lesser extent, some ability to participate in dust explosions. Zinc dust as used in the extractive metallurgy of zinc, is not known to be a reactive powder in the industry. No evidence could be found in the literature where zinc dust was involved in an explosion or explosive type event. On 3 May 2002 an explosive type incident occurred at Zincor in Springs, South Africa, which led to a fatal accident. Given the history of relative benign behaviour of zinc powders under conditions conducive to dust explosions, it was decided to share the information of this incident with industry in an effort to prevent similar incidents. Therefore, the purpose of this paper is to describe the incident that occurred at Zincor, discuss the major findings, report on corrective actions, as well as publish the results of subsequent tests that were performed to determine the conditions under which zinc powder exhibits explosive characteristics.

Jan 1, 2005

By D. B. Swanepoel

Hulamin Rolled Products (Ltd) developed a high Mn and Si containing alloy, EN 4017 as a scrap consuming alloy from the waste generated in producing their range of clad products for brazing of inter alia automotive heat exchangers. The multifaceted composition of this alloy (Al -1.2 wt% Si -1.1 wt% Mn -0.2 wt% Mg-0.26 wt% Cu) suggested that it might display some degree of strengthening via precipitate formation of the Mg2 Si-types. The aging isotherms constructed showed that EN 4017 with 0.19% Mg reached a lower peak strength (YS~210 MPa and UTS~260 MPa)compared to the EN 4017 material with 0.43% Mg (YS~270 MPa and UTS~325 MPa). The higher Mg variant of EN 4017 was comparable with the age-hardenable reference alloy EN 6061. Selected area electron diffraction (SAED) studies proved that the microstructure of age hardened EN 4017 contained a combination of ß', ß" and U2 phase after being aged at 175ºC for 65 h. The general microstructure contained precipitate free zones as well as grain boundary Si films, although these did not lead to significant embrittlement. The role of Mn dispersoids in the fracture mechanism of 4017 is also discussed. The article will compare the behaviour of EN 4017 with that EN6061. Keywords: Age-hardening, dispersoids, magnesium silicide, precipitate free zones

Jan 1, 2009

By G. du T. Judeel

An investigation was carried out to determine whether a numerical model could be constructed that would produce results that realistically represent actual ground deformations in and around a vertical shaft. The ground deformation was brought about by the partial extraction of the shaft pillar. A special characteristic of the rock masses, affected by the shaft pillar extraction, was that the shaft was located in poor quality rock masses. After the extraction of a portion of the shaft pillar, excessive deformations occurred at the shaft/reef intersection. Therefore, a decision was taken to extract the entire shaft pillar protecting the shaft by a proposed waste-cut across the shaft. The effects of stress and displacement on the shaft were investigated by using inelastic numerical modelling in different stages. A calibrated numerical model was constructed producing modelled results comparable to the actual displacements along the shaft. Des recherches ont été poursuivies pour déterminer si on pouvait construire un modèle numérique qui donnerait des résultats représentant avec réalisme les déformations réelles du terrain à l’intérieur et autour d’un puits vertical. La déformation du terrain était entraînée par l’extraction partielle du massif de protection. Une caractéristique spéciale des masses rocheuses, affectées par l’extraction du massif de protection, était que le puits était situé dans des masses rocheuses de qualité inférieure. Après l’extraction d’une portion du massif de protection, des déformations excessives se sont produites à l’intersection du puits avec le filon. Par conséquent, la décision a été prise d’extraire le massif de protection en entier par une coupe de déblais à travers le puits. Les effets de contraintes et décalage furent étudiés en utilisant une modélisation numérique inélastique à des stages différents. Un modèle numérique calibré fut construit, donnant des résultats modelés comparables aux décalages réels le long du puits. Eine Untersuchung wurde durchgeführt um festzustellen, ob ein numerisches Modell konstruiert werden könnte, das Resultate produzieren würde, welche realistisch aktuelle Bodendeformationen in und um einen vertikale Schacht darstellen. Die Bodendeformation resultierte teilweise aus der Extraktion des Schachtpfeiler. Eine spezielle Eigenschaft der Gesteinsmassen, beeinflußt durch die Schachtpfeilerextraktion, war, daß der Schacht in Gesteinsmassen geringer Qualität situiert war. Nach der Extraktion eines Teils der Schachtpfeiler, traten übermäßige Deformationen am Schacht/Riff Kreuzungspunkt auf. Folglich wurde die Entscheidung getroffen, die gesamten Schachtpfosten zu extrahieren und den Schacht mittels eines geplanten Verlustschnittes quer zum Schacht zu schützen. Die Auswirkungen des Druckes und der Versetzung auf den Schacht wurden unter Anwendung unelastischer numerischer Modelle in unterschiedlichen Stadien untersucht. Ein kalibriertes numerisches Modell wurde konstruiert, welches berechenete Ergebnisse mit den tatsächlichen Versetzungen entlang des Schachtes vergleicht.

Jan 1, 2003

Book review Pearson, J. S. Ocean floor mining. Park Ridge (New Jersey), Noyes Data Corporation, 1975. 201 pp. NIM reports Report no. 308 A mineralogical study of gold particles in pulp residues from the Bracken Gold Mine. (7th Mar.,1968. Re-issued Oct. 1975.) Report no. 377 Examination of pulp samples, treated with cyanide, for coated gold.(7th Aug., 1968. Reissued Oct.1975.) Report no. 385 The determination of the nature of coatings on gold particles. (2nd Aug., 1968. Reissued Oct. 1975.) Report no. 452 The Purlex Process - a description of the pilot plant leading to the use of the process in South Africa. (13th Jan., 1969. Re-issued Oct. 1975.) Report no. 482 Review of work on the treatment of pegmatites. (9th Apr., 1969. Reissued Sep. 1975.) Report no. 1443 Gravity concentration tests on four samples from Tantalite Valley,S. W.A. (5th Jul., 1972. Re-issued Sep. 1975.) Report no. 1489 The breakage of S oderberg electrodes. (10th Nov., 1972. Re-issued Nov. 1975.) Report no. 1545 A mineralogical investigation of leach residues from the Blyvooruitzicht Gold Mine. (22nd May, 1973. Re-issued Nov. 1975.) Report no. 1583 Preliminary tests on winnowing for the recovery of mica. (12th Nov., 1973. Re-issued Sep. 1975.) Report no. 1652 The identification of diamonds from Premier, Finsch, and Jagersfontein Mines by statistical analysis of data obtained from instrumental neutron-activation analysis. Report no. 1723 The determination of zirconium and aluminium in zirconiumaluminium alloys. Report no. 1739 The determination of trace amounts of noble metals in sulphate media. Report no. 1771 The determination of silver, selenium, tellurium, antimony, tin, lead, and arsenic in anode sludges. Report no. 1772 A study of copper recovery by lime roasting and leaching. Corrigendum The Special Issue of Volume 76 of the Journal ('Recent Advances in Mineral Dressing, October 1975) should be corrected as follows. The South African Institute Of Mining And Metallurgy - Information On Membershlp The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical, Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. Die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie - Inligting Oor Lidmaatskap Die Instituut is in 1894 gestig as die Chemiese en MIetallurgiese Vereniging van ::!nid-Afrika. In 190-1is dit omvorm tot die Chemiese Metallurgiese en Mynbouvereniging van Sllid-Afrika en in 1956 het dit die Suid-Afrikaanse Instituut vir Mynbou en l\Ietallurgie geword.

Jan 2, 1976

By J. A. L. Napier

One of the most important characteristics of tabular mine stress analysis is the need to represent the complex evolution of mining face positions and the accompanying induced stress changes in the rock mass. Integration of seismic activity with numerical modelling requires flexible and efficient solution schemes in which both off-reef damage and large-scale fault slip can be effectively represented. A new approach is investigated in which the stope closure and ride variables can be found using a moving least squares estimator. Some advantages of this approach over traditional element-based tessellation schemes are identified. At the same time, shortcomings of this method are noted when the displacement discontinuity variable is approximated by a polynomial shape function. Difficulties and possible solutions to the shape function formulation near excavation edges are discussed. Une des caractéristiques les plus importantes de l’analyse des contraintes minières tabulaires est la nécessité de représenter la complexe évolution des positions du front de taille et des changements concomitants des contraintes occasionnées dans la masse rocheuse. L’intégration de l’activité sismique avec la modélisation numérique requiert des projets souples et efficaces qui permettent la représentation des dommages hors-filon et des glissements de faille à grande échelle. Une approche nouvelle est étudiée qui permet de trouver la fermeture de la taille et les variables de montage en utilisant un estimateur par les moindres carrés mobile. Certains des avantages de cette approche sur les traditionnels projets basés sur une structure en mosaïque sont identifiés. En même temps, les défauts de cette méthode sont notés lorsqu’on calcule la variable de discontinuité du déplacement approximativement par une fonction de forme polynomiale. Les difficultés et solutions possibles à la formulation de la fonction forme près des bords d’excavation sont discutés. Eine der wichtigsten Charaketeristika der taublaren Grubenspannungsanalayse ist die Notwendigkeit, die komplexe Entwicklung der Abbaupositionen und der damit verbundenen induzierten Spannungsänderungen der Gesteinsmasse neu vorzulegen. Die Integration der seismischen Tätigkeit mit einem numerischen Modell erfordert flexible und effiziente Lösungsschemata, in denen sowohl Schäden ausserhalb des Riffs als auch Verwerfungen großen Ausmaßes effektiv dargestellt werden. Ein neuer Vorstoß wird untersucht in welchem die Strossenschliessung und Schneisenvariablen unter Verwendung des Schätzwertes der kleinsten quadratischen Abweichungen (Gaussscher Schätzwert) gefunden werden. Einige Vorteile dieser Annäherung im Vergleich zu der traditionellen Element-basierenden Tessellation sind identifiziert. Gleichzeitig werden Unzulänglichkeiten dieser Methode vermerkt, wenn die Verschiebungsdiskoniuitätsvariable durch eine polynomische Formfunktion angepaßt wird. Schwierigkeiten und mögliche Lösungen zur Formfunktionsformulierung nahe Exkavationsrändern werden besprochen.

Jan 1, 2003

By S. Pathak, B. Nilsen

Abstract: In recent years, probabilistic approach with the calculation of probability of failure instead of a factor of safety against failure is emerging in practice. The main objective of the paper is to discuss a probabilistic approach in rock slope stability analysis for Himalayan conditions. Due to the fragile geology brought about by the tectonic movements along the hill slopes, dramatic variations of the topography and intensive surface runoff during every monsoon season, serious slope failures occur frequently in Himalayan region. Slope failures have also been triggered by seismic activities. The probabilistic approach is applied to stability analysis for a road cut along the Desander back slope of the Kali Gandaki hydropower project in Nepal. It is concluded that the probability approach offers a more accurate grasp of the actual condition than any factor of safety. Zusammenfassung: In den letzten Jahren ist es mehr gewöhnlich geworden, ein stochastisches Verfahren und eine Berechnung von der Wahrscheinlichkeit eines Zusammenbruchs statt einer Berechnung von Sicherheitsfaktoren zu verwenden. Das Hauptziel dieses Artikels ist das stochastische Verfahren in Stabilitätsanalyse von Gebirghängen, welches an Himalayische Verhältnisse angewandt worden ist, zu diskutieren. Wegen der spröden Geologie die durch tektonische Bewegungen entstanden ist und den dramatischen topographischen Variationen sowie viel Oberflächenwasser während des Monsuns, kommen in der Region des Himalayas oft mehrere erhebliche Abhangszusammenbrüche vor. Abhangszusammenbruche ist auch von seismische Aktivität ausgelöst worden. Das stochastisches Verfahren ist auch benutzt worden, um die Stabilität von einem Wegschnitt in dem Desander Gebiet von dem Kali Gandaki Wasserwerk-Projekt zu analysieren. Die schlussfolgerung ist, dass die Ergebnisse eines stochastisches Verfahren die wirkliche Verhältnisse eines Abhangs besser beschreibt als der Sicherheitsfaktor. Résumé:- Ces dernières années, une approche probabiliste basée sur le calcul d’une probabilité de cassure au lieu d’un facteur de sécurité préventif d’une cassure est de plus en plus utilisée. L’objectif principal de ce papier est de discuter une approche probabiliste de la stabilité de versants rocheux en himalaya. Due à la fragile géologie causée par les mouvements tectoniques sur les versants de collines, aux dramatiques variations de topographie, ainsi qu’au lessivage intense du relief à chaque mousson, de sérieux glissements de terrains se produisent fréquemment en Himalaya. Les glissements de terrain sont aussi déclenchés par l’activité sismique. Cette approche probabiliste est appliquée aux analyses de stabilité d’une section de route le long du versant arrière Desander du projet « hydropower » du Kali Gandaki au Népal. On en conclut que l’approche probabiliste offre une estimation plus précise des conditions actuelles que n’importe quel facteur de sécurité.

Jan 1, 2003

By O. S. L. Bruinsma, M. J. Matsela, D. J. van der Westhuizen

The free ligand (FL) model is an intuitive model to calculate the equilibrium concentrations in solvent extraction (SX) based on the distribution coefficient (Kd) at infinite dilution and the fraction of free ligand available for extraction. In this work, the FL model is validated to account for co-extraction of Ni and for designing the extraction and scrubbing sections of Co/Ni separation in a base metal refinery. Cyanex 272 is employed as a selective Co extractant in the process to yield high purity Ni. To enhance the loading capacity of the extractant, 50 mol% of NaOH is pre-loaded into it. Experimental and FL modelling results show that four equilibrium stages are required to purify the 99% Ni feed to a 99.97% Ni raffinate. The 53.59% co-extract with 26.76% free ligand is purified with a reflux scrub of 30 g Co/L in one equilibrium stage to 99.01%, Co in the scrubbed extract. The FL model as well as the Co/Ni/Na-analysis of the aqueous phase confirm that in the scrubbing section, Ni in the extract is mainly replaced by Co. Finally, in the one stage stripper the Co concentration in the scrubbed extract is increased from 5.6 g Co/L in the extract to 30.5 g Co/L that is partially used as reflux scrub liquor.

Dec 11, 2024

By T. Fraszczak, U. A. Peuker, T. Mütze, O. Ortlepp

Dolomite is a calcium carbonate sedimentary rock that can be found all over the world. In its calcined form it is employed for water treatment or as an additive in iron production. Calcined dolomite is produced at the Wünschendorfer Dolomitwerk GmbH in shaft furnaces (kilns). Because of an expansion of the mined deposit, significantly higher extraction costs were expected. Therefore, the existing upgrading processes for the kiln stone fraction had to be adapted and improved. This paper presents a process optimisation which allows for an increase of the yield of calcined dolomite by 10 % due to a redesign of the crusher circuit and by an additional 5 % due to a comprehensive characterisation of the kiln stone fraction itself. Here the interdependency between the pressure drop in the furnace during calcination and the size distribution of furnace stones was used to increase the amount of fine size fractions in the furnace feed without deterioration of the calcination process. Keywords: Dolomite, crushing circuits, kiln stone production, flowability, calcination

Jan 1, 2020

By I. Satola, J. Aromaa

In this work we have reviewed methods to classify corrosivity of ground waters. Weight loss and stress corrosion cracking (SCC) corrosion tests have been done for rebar and steel strand. No clear indication of SCC was found. The application of tensile stress to 85 % of yield strength increased general corrosion rate significantly in very corrosive waters. The effect of corrosion protection on the axial behavior of steel strands was determined by double pipe axial tests with different embedment lengths. The results showed a significant difference on behavior between epoxy-coated steel strands, galvanized steel strands and plain steel strand. Dans la présente étude, nous avons passé en revue des méthodes permettant de classifier la corrosivité des eaux souterraines. Des tests portant sur les pertes de poids et sur la corrosion FCC (la fissuration par corrosion sous contrainte) ont été effectués pour les barres d’armature et les torons. Aucune indication nette de FCC n’a été constatée. L’application d’une contrainte de traction allant jusqu’à 85 % de la limite d’élasticité a accru de manière significative la vitesse générale de corrosion dans les eaux très corrosives. L’effet de la protection contre la corrosion sur le comportement axial des torons en acier a été déterminé au moyen de tests axiaux à double tube avec des longueurs d’enrobage différentes. Les résultats ont mis en évidence une différence significative quant au comportement entre les torons en acier à revêtement époxy, les torons en acier galvanisés et les torons en acier standard. In dieser Arbeit haben wir Methoden geprüft, die korrosive Wirkung des Grundwassers einstufen. Gewichtsverlust- und SCC-Korrosionstests wurden für Stahlstäbe und Drahtlitzen durchgeführt. Es wurden keine sicheren Hinweise auf Spannungsrisskorrosionsbrüche gefunden. Bei Anwendung einer Dehnbelastung von 85 % der Streckspannung bzw.Ergebnisstärke stieg die allgemeine Korrosionsrate in stark korrosivem Wasser deutlich an. Die Wirkung des Korrosionschutzes bei axialem Verhalten von Stahldrahtlitzen wurde durch axiale Tests an Doppelleitungen unterschiedlicher Versenkungslänge determiniert. Die Ergebnisse zeigten im direkten Vergleich von epoxidbeschichteten, galvanisierten und normalen Stahldrahtlitzen beachtliche Unterschiede im Verhalten auf.

Jan 1, 2003

By A. J. Jager, D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2004

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006

By D. Noort, M. Dawborn, D. O. del Castillo

This paper was originally presented at the North American/9th US Ventilation Symposium, June 2002, Kingston, Ontario, Canada. Reprinted with permission of the publishers, A.A. Balkema Publishers, Rotterdam, Netherlands. This paper is a study of the ventilation, cooling and refrigeration system design of the Mindola copper mine in Zambia. The challenges that were addressed varied from the restrictions imposed by an ageing infrastructure to the requirement for increasing the annual production rate, coupled to the introduction of a higher level of mechanization while maintaining acceptable conditions and limiting total ownership costs. A description of how the ventilation, refrigeration and cooling systems were modelled in order to obtain the projected heat loads associated with two different mining methods over the life of the project. The methodology included a number of iterations to optimise the design and include aspects such as the expected inrush of hot fissure water, the operation of diesel machinery at depths in excess of 1500m below surface, developing a cost-efficient cooling strategy and selection of the refrigeration machinery to meet the requirements imposed by the cooling strategy. This paper demonstrates the successful implementation of an integrated design approach.

Jan 1, 2005

By P. Valicek

Anglo American Platinum Limited is constantly striving to improve safety and productivity. There are many different initiatives taking place within the organization in order to ensure continued safe operation and profitable ounces for the future. One of the opportunities and potential growth areas that has been identified and is being explored is that of mechanization. In order to do this, the approach that has been adopted by Anglo American Platinum is to fully understand and analyse the current mechanized mining methods. Once each configuration is fully understood, the method can then be optimized and new mining technologies and systems can be developed to overcome the current shortfalls. This paper will discuss a methodology that was developed by Anglo American Platinum (in conjunction with Cyest Corporation) and adopted to optimize the mechanized mining layout and fleet configuration, and will also present the final findings of the study. Due to the impracticability of piloting every possible option in the workplace, extensive modelling and simulation exercises were conducted to determine realistic parameters for productivity and value. The study resulted in a full understanding of mechanized mining systems and their associated layout. From the results of the study a mining / logistic layout was developed which highlighted the following opportunities: 1. Create safe operations through the reduction of personnel in the ?high-risk zone? of stopes 2. Separate machines and personnel by use of remotely operated machines 3. Create focused mining on primary development from the production stoping, thus having dedicated teams on development and stoping. 4. Develop primary development ahead of the stoping activity. This enables: a) Understanding of the geology and subsequent implementation of the correct b) technology (?fit-for-purpose?) required to mine that area based upon this geological knowledge c) Ability to install tipping points ahead of stoping, creating ?immediate stoping reserves?, thus increasing flexibility and reducing production risk d) Improved productivity by having adequate faces available and reduction in re-development to establish faces. 5. Quicker return on Investment due to recovering revenue from ?on-reef development? 6. The layout allows flexibility between stope sections enabling better ?resource sharing? 7. Optimize the long-term ratio of machine makeup of the fleet in relation to the production outputs 8. Creates an agile mining layout allowing rapid response to market pressures. The findings and work presented in this paper is currently being implemented at different test sites within Anglo American Platinum and will demonstrate that improved safety and productivity can be achieved through the adoption of mechanization.

Jan 1, 2012

By B. I. Matshediso, J. Kaavera, E. Shemang, T. K. Dintwe, L. S. Teseletso, K. Fichani

The minerals sector continues to draw attention from policy makers who would want to see both old and new mineral projects add value to the minerals in the host country. The current technological development in the leaching of manganese oxide ores to produce a high-purity manganese sulphate monohydrate, a compound that is used in the manufacture of batteries for electric vehicles or long-life storage cells for the renewable energy market, has led to junior mining companies spearheading this technology in new projects across the globe. In this paper, we researched the high-purity manganese sulphate monohydrate project pipeline and used projected production volumes and C1 cash costs to construct the industry supply curve for six projects, including the K.Hill project owned by Giyani Metals Corporation near Kanye, in the southern part of Botswana. The aim was to determine the ideal conditions that would provide a comparative advantage for further local value addition to high-purity manganese sulphate monohydrate and to the end user product. The results showed that while the estimated C1 cash costs would place the K.Hill project as the second highest cost producer from among five projects, it would nonetheless have healthy profit margins due to the high projected price of high-purity manganese sulphate monohydrate. The study recommended policy options, which, if implemented, could further encourage the exploitation and value addition of battery metals in Botswana.

May 27, 2025

By X. Gumede

Mud houses are common structures in most South African rural homes closer to the mining operations. Fulltime dwellers in these properties are often the elderly. The mine codes of practice and the South African legislative instruments attempt to define the damage criteria to limit the effect of the blast-induced noise and ground vibrations to different structures. All these assessment criteria are based on the peak particle velocity and noise generated during blasting. The South African safe limit criterion that was adopted was initially derived from the international standards, which were then used as a local guideline. This paper evaluates the currently adopted safe limit criteria used in South Africa for a mud house, currently rated at 6 mm per second and 120 decibels to134 decibels, for blast-induced seismicity and noise, respectively. Further, a study was performed on a residential house near a coal mine (5.26 km) based in Mpumalanga following numerous complaints by the owner, launched at the mine and to the Department of Minerals and Petroleum Resources. The aim of the study was to measure the magnitude of blast-induced triggers experienced at the aggrieved homestead and to establish if there is a likelihood that an irritation or damage may be caused by these triggers. The seismometer was installed at about 2 m from the mudhouse, from 1 July 2022 to 31 of July 2022. Five blast-induced triggers were recorded during the period showing an average of 0.09 mm/s and 121 decibels for blast-induced seismicity and noise, respectively. The results obtained indicated a maximum seismicity of 0.15 mm/s. This seismicity was below the perceptible vibrations obtained from daily home activities such as walking, jumping, and door slamming, which produce 0.8 mm/s, 7.1 mm/s, and 12.7 mm/s, respectively. Seismicity was therefore not likely to have caused any annoyance and or damage. For noise, the results indicated a maximum of 123 decibels and an average of 121 decibels from five events recorded. A literature review suggests that slight damage may occur when airblast frequencies match the natural frequencies of structures at 120 decibels. Based on these results, it can be concluded, therefore, that the noise, rather than seismicity, is more likely to be the cause of damage to the structure assessed. For improvement, a new approach is proposed based on relating the safe limits to the structural and human response.

Dec 15, 2025

By Raphael Banda

1 Initiating Systems ? a definition An initiation system is a combination of explosive devices and component accessories specifically designed to convey a signal and initiate an explosive charge from a safe distance. In the use of explosives, the initiating system performs the functions of transmission and control of the firing signal to each explosive charge. As functional groups, initiating systems may be considered as: Starters Those which provide the initial signal to start the blasting process. Surface systems Products which provide transmission of the starter signal and delay timing (if any) across the surface of the blast outside the blast hole. In-hole systems Products which provide the signal transmission, delay timing (if any) and the initial explosives energy in the blast hole.1 2 Different types of Initiating Systems The initiation systems commonly used in Sub Saharan Africa are: ? Detonating cord and detonating relay systems ? Capped fuse and igniter cord systems ? Shock tube non electric systems ? Electric systems ? Electronic detonators 3 Overview of Electronic Delay Detonator Technology Conventional detonators use pyrotechnic delay elements and the variation of the actual delay periods is at best approximately 1% the nominal delay. The lack of guaranteed precision common to all pyrotechnic systems enhances the likelihood of negative environmental blasting effects.3 For example, take a 500 ms in hole delay. In conventional detonators this means that 95 % of shots fire within 10 ms of the mean. i.e. a window of 20 ms. Taking a fixed interval between shots of 25 ms, with a range of ± 3 ms, a very ragged firing pattern could be expected which in practice would result in non uniform fragmentation.

Jan 1, 2005

1. Book reviews Quantitative texture analysis, edited by H. ,}. Bunge and C. Esling. Deutsche Gesellschaft fur Metallkunde, 1982. 551 pp. Reviewer: L. 1\'1.Matthews Boundary element methods in solid mechanics by S. L. Crouch and A. M. Starfield. Reviewer: J. A. C. Diering World mineral statistics 1976-1980. Produdion,' exports,' imports, by Institute of Geological Sciences. London, Her Majesty's Stationery Office, 1983. £18.00 Reviewer: R. P. King 2. New publications Canadian mines,. perspective from 1982. Mineral Bulletin MR 197. Supply and Services Canada, Hull, Quebec K1A 059, Canada. Copper' s changing cost structure, by Commodities Research Unit Ltd (31 Mount Pleasant, London, WClX OAD, England). Petrology of metamorphic rocks, by M. Suk. New York, Elsevier, 1983. 320 pp. U.S. $68.00. Applied geomorphology, by H. Th. Verstappen. New York, Elsevier, 1983.442 pp. U.S.$95.75. Tin and its uses, no. 137, by the International Tin Research Institute. Greenford, the Institute (Fraser Road, Greenford, Middlesex UB6 7AQ, England), 1983. 3. New journals Mining Science and Technology, edited by C. 0, Brawner and B. N. Whittaker, is to be published quarterly in one volume per year by Elsevier. Aluminium, published monthly by Aluminium -Verlag GmbH, P.O. Box 1207, D-4oo0 Diisseldorf 1, F.R. Germany. DM 690.00 per annum. Rock mechanics The South African Institute of Mining and Metallurgy is to hold two schools on 'Rock Mechanics in Mine Management' at the University of the Witwatersrand, Johannesburg, from 23rd to 27th January, 1984, and from 30th January to 3rd February, 1984. The Federation of Societies of Professional Engineers The Federation of Societies of Professional Engineers (FSPE) has been a member of the World Federation of Engineering Organisations (W FEO) for many years and has regularly sent delegates to the biennial conference of that organisation. Second progress report by ASRET The Professional Engineers Joint Council was estabislhed in 1960 and initially its main fWlction was to represent the interests of engineers. Explosives technology The Center for Explosives Technology Research (CETR) has been established at the New Mexico Institute of Mining and Technology (Tech) in Socorro, New Mexico. International Tunnelling Association A conference entitled 'Ita Tunnels 1984' will be held in Caracas, Venezuela, from 2nd to 7th June, 1984. Automation The IFAC Symposium on Automation for Mineral Resource Development is to he held in Brisbane (Australia) from 9th to nth July, 1985.

Jan 1, 1983

Report M48 Tracer tests on furnaces at M etalloys Limited. Report M52 A high-speed, multi-input serial-interfacing system for a computer with simultaneous back-1lP recording on magnetic tape. Report M53 The development of an automatic sample-changer and control instrumentation for isotope-source neutron-activation analysis. Report M69 The determination, by X-ray-fluorescence spectrometry,of tin and tungsten in ores, concentrates, and residues of scheelite, wolframite, and cassiterite. Report M77 Analysis of the results of a marked-ball test in relation to theories of ball wear in rotary mills.

Jan 1, 1983

By Pierre Marcotte

Jackleg rock drills expose their operators to high hand-arm vibration levels. To address this problem, an antivibration handle has been developed. The antivibration properties of the handle were achieved through a suspension based on a hinge design, achieved with a torsion spring and o-rings. To provide some bench marking for this new handle and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. Testing of four antivibration handles on the test bench have shown reductions of the overall weighted acceleration level in the order of 54 % to 60 %, with most of the attenuation occurring in the zh-axis at the rock drill percussion frequency.

Jan 1, 2008

The Steering Committee for Minerals and Mining Policy convened two workshops during March 1996 to address the following topics: Business Environment- National and Provincial Powers, Administration and Regulation, Mineral Marketing, Beneficiation, Research and Development, Environmental Issues, Mining Impact on Surface Usage, Southern Africa Regional Issues. Human Resources: Elementary Residual Racism, Housing, Downscaling, Migrant Labour and Human Resource Development. Mineral Tenure: Mineral Rights, System of Access to Mineral Rights, Access to Exploration information, optimal Exploration, Trust Lands. Small-scale Mining. Development of Small-scale Mining, Artisanal Mining.

Jan 1, 1996