Search Documents

By J-C. Lv, S. Zhao, F-L. Zhang, T. Yan

"To eliminate nozzle clogging during continuous casting of ship plate steel and reduce the calcium addition required, the composition of CaO-MgOAl2O3 inclusions in the liquid phase region must be controlled. Thermodynamic calculations using FactSage show that when the balanced Al content is 0.03 mass %, aCa in the liquid steel is 1–10 ppm, and aMg is 0.01–0.3 ppm; and when the balanced Al content is 0.06 mass %, aCa in the liquid steel is 1–30 ppm, and aMg is 0.05–0.9 ppm. The CaO-Al2O3-CaS inclusions can be controlled in the liquid region below 1600°C at aCa values of 5 ppm, 15 ppm, and 30 ppm, and the balanced Al content should be controlled in the range of 0.001–0.050, 0.005–0.250, and 0.010–0.50 mass %, respectively. Based on theoretical analysis, the refining slag composition should be controlled to 45–53 mass % CaO, 30–37 mass % Al2O3, 6–12 mass % SiO2, and 6–8 mass % MgO. Optimization of the slag system and steel composition can reduce, or even eliminate, the requirement for calcium treatment. The total oxygen content in the slab can be controlled to 15–21 ppm, with typical micro-inclusions ??10 ??m in size, with compositions in the CaO-Al2O3-MgO and CaO-Al2O3-CaS systems. Introduction With the rapid growth in steel output in China and the changes in the macroeconomic environment, competition in the steel industry has become more intense. The technology for economical cleaning of high-grade steel is important for improving product quality and reducing production costs. However, the functions of refining equipment have not been fully taken into consideration, and the combination of refining methods has not been optimized completely. These problems have become a bottleneck, restricting modern steel enterprises from developing an economic clean steel production process. Ship plate steel produced by the converter long process has been selected as the example in this study. The composition of the steel is shown in Table I. This steel is a high-strength low-alloy steel for rolling media and heavy plates, mainly used for ocean-going vessels and other steel structures. The carbon content in the steel is far from the peritectic point, and the crack sensitivity of the slab surface is weak, so impurities and gas content are strictly limited. Therefore, the process route BOF (basic oxygen furnace) – LF (ladle furnace) – CC (continuous casting) needs to be studied."

Jan 1, 2018

By R. Singh, A. K. Dhawan, M. Dixit, H. Dev

ABSTRACT: The modulus of deformation of rock mass is an important engineering parameter required for the design of foundation of hydraulic structure and to study the interaction of rock mass and the structure at the foundation support. Different equipment and techniques are used to arrive at the design modulus value. Since any error in the estimation of modulus values results in multiplication of its effects in the analysis, it is necessary to know about the reliability of testing equipment and procedures. In the present study modulus values obtained by different in-situ equipment at different project sites have been compared. KURZFASSUNG: Der Verformungsmodul von der Felsenmasse ist technisch ein wichtiger Parameter, den man zur Konstuktion des Grunds fuer die Hydro – Tektonik, benoetigt um auch die gegenseitige Beeinflussung der Felsenmasse und der Tektonik am Traggrund zu betrachten. Verschiedene Geraete und Methoden werden angewandt, um den Ausfuehrungsmodul -Wert zu erreichen. Es ist erforderlich, die Zuverlaessigkeit der Pruefeinrichtung sowie des Verfahrens zu kennen, da irgend ein Fehler in der Abschaetzung von Modulwerten in der Analyse zu einer Vervielfachung ihrer Einwirkung fuehrt. In der vorligenden Arbeit werden die Modulwerte gewonnen aus unterschiedlichen Einrichtungen an Ort und Stelle and verschiedenen Projekt -Stellen mit einander verglichen. SOMMAIRE: Le module de deformation d’une roche est un parametre important pour la conception et realisation des ouvrages hydrauliques ainsi que pour etudier l’interaction de la roche et de la structure d’appuis de base. De divers equipments et techniques sont employes pour determiner la valeur de ce module de conception. Puisque l’effet d’une erreur d’evaluation du module devient multiplie dans l’analyse, il est necessaire de savoir la fiabilite des equipments et des methods qu’on ulilise. Dans cette etude, on a compare les valeurs des modules obtenues en employant les equipments in-situ aux sites differents de projets.

Jan 1, 2003

By S. Adams, J. R. C. von Holdt, J. L. Broadhurst

Fugitive dust from mineral extraction and processing activities can significantly influence air quality, the environment, and the health and quality of life of workers and surrounding communities. Poor engagement and communication between experts and lay persons, disciplinary silos and polarised viewpoints have made it difficult to develop a holistic understanding of the complex health issues associated with environmental emissions of mine dusts, and consequently to design meaningful and integrated approaches to address such issues. The collaborative Global Challenges Research Fund (GCRF) Mine Dust and Health Network, hosted by Minerals to Metals at the University of Cape Town, serves as a collaborative think-tank to inform research directions within and across disciplines, government policy and regulations, health monitoring programmes at public clinics, industry best practice, community healthcare and impact prevention programmes. It focuses initially on the southern African region, but with the intention to expand to mining-intensive developing countries within the rest of Africa, South America and Asia. This paper outlines the approach and activities of this global transdisciplinary and intersectoral network and presents some of the key outputs and achievements to date. Keywords: Mine dust, Global Challenges Research Fund Mine Dust and Health Network

Jan 1, 2020

By C. A. F. Sweet

The inter-relationship between these parties and the effect on the outcome of the project is often grossly underestimated. There are numerous success stories where the parties have worked as complementary teams aiming at the best outcome for the client company and achieving significant success. While there are a good number of occurrences where either the roles of the parties were unclear or perceived to be different from what others in the team believed or required them to be and the results were less than desired. This usually resulted in ongoing conflict, incorrect focus, working to different agendas and the result being a less than optimum result to Client Company. Mining, by its very nature of exploring where you cannot see, be it a shaft being sunk, tunnel being developed or other excavation that needs to be made, requires a very special working relationship between the parties. To understand this, and it applies equally well to mine and plant construction and other multiple function projects, one needs to start by describing the relationship of the parties. Often people believe that because they manage ongoing complex operations and large numbers of people that they can manage projects and as such the participants will ?fall into line.? At the outset it needs to be stressed that ?Project Management? is a specific type of management and needs to be understood as such. There are enough Colleges and Universities that teach project management, not only as a subject but also as a Master Degree. As you start up your project the relationship you establish between the client, project team (C.P.T) and the Engineering, Procurement, Construction and Management team (EPCM) will largely determine how successful your project will be. It is essential that from the outset a spirit of co-operation, support and respect be nurtured, and that it be actively carried through the project life cycle. There are several methods to facilitate this including team building exercises right at the start. This time and money will be well spent and recouped many times over during the project life cycle.

Jan 1, 2005

By T. Ito, N. Tokashiki, H. A. Bilgin, Ö. Aydan, T. Akagi

This study is concerned with the electric potential induced by deformation, fracturing and sliding of non-piezoelectric geomaterials. In experiments, the acoustic emissions together with electric potential measurements were also measured in order to see how the so-called seismic electric signals are associated with new fracture occurrence and propagation and sliding in case of existing discontinuities. The outcomes of this experimental study may explain why such electric potential variations may occur during the fracturing and sliding of non-piezoelectric geomaterials. On the basis of these outcomes, their possible implications in geo-engineering and geo-science are discussed. Ce travail concerne 1e potentiel électrique produit par la déformation, 1a fracture ou le glissement du matériel géologique non-piézoélectrique. Aux expérimentations, on a mesuré 1es émissions acoustiques avec le potentiel électrique afin de constater la relation entre les phénomènes de glissement ou de formation et de propagation de nouvelles fractures le long des discontinuités existantes. Les résultats de ce travail expérimental expliquent pourquoi de telles variations de potentiel electrique se produisent durant le glissement ou la fracture du matériel non-piézoélectrique. Sur la base de ces résultats, on a discuté de leurs éventuelles implications dans les domaines de 1a géologie et de 1a géo-ingénierie. Diese Studie befasst sich mit dem elektrischen Potential das durch die Deformation, Bruchbildung und Gleiten von nicht-piezoelektrischen Geomaterialien induziert wird. In Experimenten wurden die akustischen Emissionen zusammen mit elektrischen Potentialmessungen gemessen, um zu sehen, wie die so genannten seismischen elektrischen Signale mit neuer Bruchbildung und Ausbreitung sowie Gleiten im Falle von vorhandenen Diskontinuitäten verbunden sind. Die Ergebnisse dieser experimentellen Untersuchungen könnten erklären warum elektrische Potential Schwankungen während der Bruchbildung und dem Gleiten von nicht-piezoelektrischen Geomaterialien entstehen. Auf der Basis dieser Ergebnisse, wurden ihre möglichen Implikationen in Geoingenieurwissenschaften behandelt.

Jan 1, 2003

By X. M. Prévost

The reassessment of coal reserves has become a matter of urgency and has come as a result of the present situation of the industry, in the context of globalized coal economies, as well as new mining legislation and the advantages and difficulties of domestic coal suppliers. The de Jager report concerning coal reserves, released twenty years ago, can no longer be used as an estimate for accurately forecasting South Africa’s future coal production. The new reserve and resource study will promote the diversification of energy sources and provide a clearer view of the future of coal mining in the country. With plans to increase South Africa’s coal export capacity to approximately 84 million tons by 2005, it is uncertain whether the country really has sufficient reserves to meet this expansion, as well as satisfy the projected increase in inland demand. The face of South Africa’s coal industry and by association, the economy of our coal-dependent country, are both set to change. This is mainly due to factors such as the demise of most of the large collieries over the last approximately twenty years, growing numbers of economic empowerment producers, the emergence of strong competition in the export market, the dawn of Clean Coal Technologies (CCTs) and the Kyoto Protocol The paper will attempt to dispel some of the current myths about coalfields and reserves and highlight potential areas of high quality coal reserves, available mainly to new entrants in the industry. Keywords: Central Basin, Clean coal technologies, Coal combustion, Coal exports, Coalfields, coalLink, Coal reserves, Coal resources, Coal processing, Colliery, Economic empowerment, Discards, Fluidized bed combustion, Low-ash coal, Metallurgical coal, Power generation, Pulverized fuel, Reserve blocks, Richards Bay Coal Terminal, Run-of-mine production, Saleable production, SAMREC Code, South Dunes Coal Terminal, Steam coal, Synthetic fuels.

Jan 1, 2003

By W. V. Mutler

Present day capital costs are analyzed for a 2,000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By K. L. Morton, R. .. J. Connelly, P. C. Bouw

Uncertainties in the forecasting of the volume of groundwater likely to enter underground workings present difficulties for mine management in planning and costing the water-related activities of mining. This paper describes a technique that was developed to assess future inflows into a gold mine in the Orange Free State. The approach employed was based on the interactive operation of two separate computer models: a regional-flow model and an inflow model. As a first stage, a regional finite-element model of groundwater flow was set up and calibrated. Predictive runs were made to establish the influence of mining on the water levels from base-line conditions. This step was necessary since observations of the regional water levels were sparse. The predicted water levels were transferred to the inflow model, and the future flowrates were calculated. Both models were calibrated by trial and error until a satisfactory match was obtained between historical records and the values predicted by modeling. In this way, an improved monitoring system to record regional water levels and pressure heads within a mine was established. By the use of information, the initial model predictions can be refined as mining progresses. The models used are based on a non-linear relationship between the area mined and the inflows. A phased behaviour in the rates of inflow increase was noted. In conclusion, the modeling approach can provide mine management with guidelines for dewatering requirements. The confidence levels depend upon the records that have been collected during the mine's history.

Jan 1, 1988

By T. C. Alex, K. M. Godiwalla, R. K. Jana

Manganese nodule, available in ocean beds, is a potential resource of the future for copper, nickel and cobalt. Recovering only these metals, containing less than 3% by weight, will result in the generation of large amount of residue. In addition to the material losses, several environmental and ecological problems arise out of this. The present study has been aimed at reducing the environmental and ecological problems associated with massive generation of this residue together with utilization of the resources. Presence of ~ 20% manganese and ~16% silicon in the residue has prompted us to check its suitability as a raw material for silicomanganese production. Lower manganese content and lower Mn/Fe ratio of the residue than that required for silicomanganese production has been corrected in this study by suitable blending. The efficacy of blending and its thermodynamic aspects using FACTSAGE software are discussed. The studies conducted indicate viability of bulk utilisation of the residue through silicomanganese production and thereby reducing the burden on environment to a great extent.

Jan 1, 2007

By R. L. Setsepu, S. O. Bada, J. Abdulsalam

The utilization of biomass as a solid fuel for co-firing has received great attention from boiler manufacturers as a clean coal technology (CCT) option. This research aimed to produce biocoal pellets, as a clean energy fuel, using hydrochar from trees planted to rehabilitate acid mine drainage (AMD) water and fine coal discards. The hydrochar was synthesized by hydrothermal carbonization of Searsia lancea harvested from AMD-contaminated land at a temperature of 280°C and a residence time of 90 minutes. It was blended with discard coal (–1 mm) at ratios of 25% and 50% hydrochar to produce different forms of solid pelletized biocoal (BC). The physicochemical and mechanical properties of each of the biocoal pellet blends were determined. The 100% hydrochar had the highest calorific value of 29.99 MJ/kg, while the raw discard coal had a calorific value of 16.73 MJ/kg. The ash content decreased from 42% in the discard coal to 25% in the blend of 50% coal and 50% hydrochar biocoal pellets. Biocoal pellets comprising 25% hydrochar and 75% discard coal (BC25 HC/75 COAL) displayed the best mechanical properties (compressive strength 3.06 MPa) of all the fuels, but the physicochemical properties were inferior to the BC50 HC/50 COAL pellets. This research has demonstrated that hydrochar synthesized from a tree species planted for hydraulic control of AMD has the capability to act as a binder for improving the mechanical properties and energy characteristics of fine discard coal.

Dec 1, 2021

Most processing plants use automatic samplers to extract ore aliquots along a producing shift. These aliquots are combined into a sample normally sent to lab analysis. The sampler used in the extraction of an aliquot from a continuous flow of ore, i.e. a belt conveyor is required to be both precise and accurate. Surprisingly, not all commercial automatic samplers exhibit these two mandatory properties. Consequently, it is recommended the development of a procedure able to check sample assays reproducibility obtained using a given sampling protocol. This paper uses the Gy’s sampling theory to evaluate coal quality control practices at a washing plant using an automatic sampler extracting coal increments from the ROM feeding belt conveyor. Gy’s theory provides the means to establish the precision limits for a given sampling protocol. Various ore properties are required to be determined in combination with sample mass and mass of the lot sampled. All this information leads to the definition of the precision limit. The precision limit obtained was checked via an experiment mimicking what happens in situations where both miner and consumer use the same and appropriate sampling practices. The experiment demonstrates that sampling theory precision limits were valid if unbiased samplers are used by both parties, i.e. miner and consumer. Keywords: sampling, quality control, coal

Jan 1, 2003

By A. R. Leach

Anomalous mining conditions can be described where the level of hazard is increased relative to normal conditions within a mining area. Normal conditions would be those defined as a Ground Control District in a mine’s code of practice, and for which mine standard support layouts are generally developed. It has been found that up to 80% of fall of ground accidents occur where anomalous mining conditions exists, typically in the vicinity of geological weaknesses. These areas require specific attention to ensure they are readily anticipated and identified and that appropriate strategies are used to reduce the hazards associated with them. As part of SIMRAC project GAP 607 checklists to aid identification and best practice mining methods were identified for a range of geotechnically anomalous conditions.

Jan 1, 2003

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

By H. C. Voges

The concentration of cassiterite at Iscor's Uis Mine is described, and information is given on aspects of the concentration of iron ore at Thabazimbi and Sishen Mines. At Uis, a very Iow-grade tin ore is concentrated by three-stage jigging, spiral concentration, and tabling to give a high-grade concentrate with a recovery of 80 per cent of the tin. A Iow-grade tantalite-columbite concentrate is also produced. The possibility of recovering mica, the use of sluice boxes instead of spirals, and the recovery of cassiterite from minus 45 µm material are being investigated. At the two iron-ore mines, heavy-medium separation is applied to size fractions larger than 0,5 mm. The types of ferrosilicon and the circuits used for the recovery of ferrosilicon from the various dilute-medium circuits are described. The spiral-concentration plant being installed at Thabazimbi for the treatment of the minus 0,5 mm portion of the ore is described.

Jan 1, 1982

By B. Dias, P. C. Schutte

Work-related musculoskeletal disorders (WMSDs) affect the wellbeing of workers and result in poor quality work, lower work performance and decreased motivation. In contrast to ‘occupational’ diseases where there is a direct cause-and-effect relationship between hazard and disease (e.g., asbestos and asbestosis, lead and lead poisoning), ‘work-related’ diseases are multifactorial, where the work environment and the type of work that is performed contribute significantly to musculoskeletal disorders. WMSD is the term used to describe disorders and diseases of the musculoskeletal system (i.e. muscles, joints, ligaments, tendons and nerves). WMSDs are by definition a work-related phenomenon. The literature shows inarguably that certain jobs and certain work-related factors are associated with a significant risk of contracting a WMSD. It is assumed that repeated movements and postures, static work, continuous loading of the tissue structures or lack of recovery time, trigger or cause a pathological process that then manifests itself as a WMSD. This paper looks at the prevalence of the WMSD condition at three mines in South Africa: a coal, a gold and a platinum mine. Predisposing factors that include work factors, presentation of symptoms and psychological factors will be discussed in the paper.

Jan 1, 2003

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

ORANGE FREE STATE BRANCH Proceedings of the Annual General Meeting The Annual General Meeting of the Branch was held in the St. Helena Club on Tuesday, 3rd October, 1972 at 8.00 p.m. Mr J. M. Meyer was in the chair. METALLURGISTS AND COMPUTERS An address delivered at the Annual General Meeting of the O.F.S. Branch by Prof D. D. Howat. Most men who remain in mining and metallurgy like their jobs. There are many times when you say to yourself or to your wife - 'Anybody can have my job - if they want it'. You feel so fed up and frustrated everything that could go wrong has gone wrong.

International Solvent Extraction Conference 1971 ISEC '71, which will be held in The Hague, The Netherlands, from 18th to 23rd April, 1971, is being sponsored by the Society of Chemical Industry in association with the Koninklijk Instituut van Ingenieurs, the Institution of Chemical Engineers and the Koninklijke Nederlandse Chemische Vereniging. The Working Party on Distillation, Absorption and Extraction of the European Federation of Chemical Engineering is participating in the Conference, which is the 101st event of the Federation. The scope of the Conference covers the entire science and technology of liquid-liquid extraction as applied in all branches of industry. Thus sessions will cover both chemical and chemical engineering aspects of the subject as applied to both inorganic and organic solutes. The conference aims to bring together academic and industrial workers in the field from all parts of the world. The programme includes over 100 papers by authors in 26 countries. Full details of the papers, together with registration forms, are contained in a detailed programme, copies of which are now available from: ISEC '71, 14 Belgrave Square, London, S.W.1, U.K. Department of Mining and Mineral Technology of the Royal School of Mines Postgraduate Courses Technical and economic challenges facing the minerals industry, together with progressive change in methods and equipment, increasingly necessitate re-training of experienced professional engineers who aim for top places. In order to meet this need, this Department has for some years run one year M.Sc. courses. Engineers, often sponsored by their employers, have a choice of three courses which are respectively devoted to mining, applied rock mechanics or mineral process design. The course in Mining is divided into five subjects, which are treated from the business management point of view. It is intended to provide middle management with a knowledge of those techniques that are required by the mining engineering function in the preparation of modern projects. The course in Mineral Process Design provides a systematic use of mineral sciences, engineering and economics for ore testing and process design, so as best to balance the technical and financial requirements for specific mineral resources. The course in Engineering Rock Mechanics is designed to provide a specialized training in the engineering applications of rock mechanics for engineers and geologists, so that they are equipped to treat a wide variety of problems in mining and civil engineering. Prerequisite qualifications are a good first degree in a related subject, plus industrial experience: The rewards include an M.Sc. of the University of London and the Diploma of the Imperial College (DIC). The limited number of places available (12 in each group) makes early application advisable. Full details are available from the Registrar, Imperial College, London, S.W.7.

Professor R.P. King holds a Ph.D. degree in chemical engineering, which he obtained at the University of Manchester in 1963. After that he lectured in the Departments of Chemical Engineering at the Universities of the Witwatersrand and Natal. From 1968 to 1973, he was Leader of the Chemical Engineering Research Group of the National Institute for Metallurgy at the latter University. Mr C.E. Fivaz, Pr. Eng., is Chief Consulting Metallurgist of Rand Mines (Mining & Services) Limited, and is responsible for the metallurgical activities of the Gold and Uranium Division and the Coal and Base Minerals Division of the Group.

Jan 1, 1984

By A. Melkumyan, K. Silversides

Chemical assays collected from blast holes have the potential to greatly improve the local accuracy of grade models. Assays must be assigned to the correct domain or they will introduce errors. Boundary surfaces created from the widely spaced exploration holes (~50m) do not provide sufficient resolution to correctly delineate domain boundaries between closely spaced (3-5m) blast holes. This paper demonstrates a probabilistic method for classifying production blast holes near domain boundaries. Gaussian processes models are applied to identify the assays and assay ratios most suited to distinguishing particular domains. These models are combined with the exploration based surfaces to classify the blast holes that can be confidently assigned to a particular domain. A reiterative method is used, where information from the blast holes closest to the exploration holes is used to label blast holes further away. This is tested on two domain boundaries in a banded iron formation-hosted iron ore mine.

Sep 1, 2021