Search Documents

By J. A. Venter, M. K. G. Vermaak

There are practical indications that flotation recovery of palladium bismuth tellurides is poor. This work tested whether this can be caused by a lack of interaction of the collector with the telluride. Impedance measurements, voltammetry and Raman spectroscopy were performed to determine the interaction of dithiocarbonate collectors (KEX) with Pd-Bi-Te. Impedance measurements showed lower capacitance values in solutions containing KEX indicating the formation of a continuous surface layer. Anodic and cathodic polarization diagrams show the mixed potential tobe higher than the reversible potential of the xanthate-dixanthogen equilibrium reaction; hence the formation of dixanthogen on the surface is possible. Electrochemically controlled in situ Raman spectroscopy did indicate the presence of bulk diethyl dixanthogen on the surface. Raman spectroscopy has confirmed the co-presence of xanthate with dixanthogen, indicating that xanthate retains its molecular integrity when it adsorbs on the surface of the Pd-Bi-Te. As a result, the mineral surface is expected to be hydrophobic and a lack of collector interaction with the mineral is not the reason for low PGM recoveries experienced. Keywords: Raman spectroscopy; Pd-Bi-Te; ethyl xanthate; platinum flotation; Great Dyke; Pd-bearing bismutho-tellurides and moncheite.

Jan 1, 2004

By J. L. van Niekerk, J. Gunaselvam

This study investigates the use of appropriate seating systems for the control of whole-body vibration exposure in vehicles used in the SA mining industry. Six suspension seats were tested with six test subjects to determine the most suitable seat for an articulated dump truck based on the EM1 requirement in ISO 7096 (2000) standards. Transmissibility functions were measured in the laboratory using the newly commissioned Dynamic Seat Testing Facility with two excitation levels of 1m/s2 and 2 m/s2 r.m.s. in the 0.5 - 30 Hz frequency range. SEAT values were calculated for two input spectrums, the EM1 input spectrum specified as in ISO 7096:2000 and measured road vibration data measured on a typical articulated dump truck. The averaged SEAT value calculations indicated that not one of the seats will qualify as an ISO 7096 (2000) suspension seat but that it is possible to select a seat that will significantly reduce the vibration the driver will be exposed to.

Jan 1, 2003

By Willem Le Roux

The common law requires an employer to take reasonable steps for the safety of employees. In general, the duty of care means that the employer, acting personally or through its employees or agents, must take reasonable care for the safety of its employees (Van Deventer v Workmen?s Compensation Commissioner; 1962 (4) SA 28 T; Oosthuizen v Homegas (Pty) Ltd 1992 (3) SA 463 T).The duty of care includes the provision of safe premises, safe machinery and tools and a safe system of work. The obligation is not an absolute one, but is restricted by the concept of reasonableness. The common law duty may, in certain cases, include the assessment of hazards and risks. 2 International law Great emphasis has been placed in the Western world on the prevention of occupational diseases and injuries. Detailed statutes and regulations govern specific industries in many countries. See, e.g. the Control of Substances Hazardous to Health Regulations of the United Kingdom and various regulations applicable to the use of asbestos and lead, fire protection, mines and quarries, petroleum, etc. Risk management is an important part of managing health and safety. In the United Kingdom, the Management of Health and Safety at Work Regulations, 1999, require every employer to make a ?suitable and sufficient assessment of the risks to health and safety of his employees to which they are exposed whilst they are at work?. The particularity of the assessment is determined by the risk in question.

Jan 1, 2011

By S. J. Ramokgopa

The development of the modern State and the growth of capitalism involves a complex process of interaction between cross-cutting structural dimension: first between politics and economics and, second, between market and hierarchy. Central to such developments are political economies of scale. Mineral specialization in the Third World developed within the framework of an international extension on oligopolistic structure of the advanced capitalist economies of Western Europe and North America. Up to the late 1960s, the world mineral and metallurgical industry was closely controlled by a handful of Western mining and industrial groups. To the extent that, foreign control of the mining sector was seen in the Third World producing countries both as the essence of foreign domination and as its major symbol. In some newly industrializing countries, the State took a more direct role in tying the economy and society together. Central to this process was the growth of large-scale finance capital. From early 1959to the mid-1970s, metal consumption in industrial countries expanded well beyond their domestic mineral endowments. And a free access to Third World minerals was a major element of the economic dynamism of these countries throughout that period. With the change in the characteristics of international investment, Africa has become less important as an outlet for capital exports of European countries. Actually, the African continent now receives only a very minor share of direct foreign investments of Western enterprises. International political economy is concerned first of all with the relationship between the economic and political domains across territorial boundaries. Second, attention should be drawn to the role of the State as the focus of decision-making in a system of competitive States, that is in turn, interdependent with a trans-national market economy in which mining and metallurgy are essential activities that affect the politics of the State, and how this in turn, rebounds on the politics of the international system. Understanding the role of the State must go beyond the glib pronouncements on the ?national interest?. How, and whose interest, the ?national interest? is determined, is precisely the problem. This implies a third theoretical problem that must be addressed: the linkage between the domestic and international domains (or levels of analysis), given that political-economic processes clearly cut across the lines of political decision-making constituted by the institutional structures of the State. Situating the State and economic interests within this vast ?state-society? complex that we call the global order will be a crucial problem for any theoretical approach that involves mining and metallurgy.

Jan 1, 2002

By M. G. Wimberger

The Merensky Reef zone, as developed on Impala Platinum?s Rustenburg Operations, displays a gradational mineralized zone, with grades decreasing from the Merensky Pegmatoid Unit into the footwall and hanging wall. A system of identifying a manageable method of defining the mining cut is introduced, termed the grade profile attenuation cut-off grade. Although horizontal grade selectivity is not applied in the mining of the Merensky Reef zone, low extraction of the orebody, due to manageable and non-manageable factors, can contribute to a reduction in revenue, even losses, due to fixed cost contributions in the mining and beneficiation of the ore. A model is proposed that integrates all variables affecting the revenue of the mining operation, including the grade profile attenuation cut-off grade, the extraction factors, commodity prices and exchange rates, utilizing numerical simulation techniques in a PC-based environment. A breakeven extraction factor for a specific cut-off grade is delivered for a range of market conditions. The breakeven extraction factor is a useful guide when designing mining layouts in structurally complex and low metal content areas. Incorporating distribution functions for individual commodity prices and exchange rates into the model provides mineral resource managers with a risk profile for individual mining areas. Shaft areas have varying grade profiles and each area should have individual models run, to prevent generalizations being made about acceptable risk levels on mining areas.

Jan 1, 2004

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

By M. A. W. Bryson

Platinum group metals are extracted almost exclusively in South Africa from three very different zones in the Bushveld Igneous Complex, called the Plat, Merensky, and the UG-2 reefs. The Plat reef is currently being exploited only by Anglo American Platinum, whereas the Merensky reef is exploited by them, Impala Platinum, Northam, and Lonplats. The UG-2 reef, on the other hand, is also processed by these producers, but Kroondal and Barplats have operations that exclusively treat ore from this reef. At present the extraction of pgms from ores in South Africa follows the traditional route of upgrading to a concentrate in a minerals processing circuit, further upgrading to a matte in a smelter, and final upgrading and separation of the individual metals in a refinery. Thus all operations that extract pgms require a minerals processing circuit, the design and performance of which is a topic of much interest, as it is a poorly understood and not a very efficient process in relative terms, compared to the other processes. Recoveries across the minerals processing circuit of between 75 and 90% are the norm.

Jan 1, 2004

By L. K. Smith

The position of Australia as a continuing long-term supplier of mineral sands, and their upgraded products, has been reinforced with the discovery of the extensive mineral reserves in the Murray Basin, an area covering parts of South Australia, New South Wales and Victoria. A major impurity in the Murray Basin is chromium, mainly present in ilmenite concentrates as individual chrome spinel grains. Magnetizing roast treatments are being evaluated as a means of removing the chrome spinel impurity from the ilmenite and as a result of the roast and magnetic separation treatments, the chrome spinels can be expected to be concentrated in the non-magnetic reject fractions. It is from these fractions that attempts were made in this study to recover a chromium-rich product by magnetic fractionation and by application of flotation. The high gauss non-magnetic rejects from the roasting of a primary and a secondary ilmenite fraction were magnetically fractionated to obtain a product with 40.5 and 28.7 per cent Cr2O3,respectively. From the high gauss non-magnetic reject from the roasting of a primary ilmenite, flotation produced a chromium-rich product assaying 29.5 wt per cent Cr2O3at 69.0 per cent recovery. In another test a magnetic fraction assaying 32.9 wt per cent Cr2O3was floated to yield a chromium-rich product with 39.7 wt per cent Cr2O3at 96.4 per cent recovery. X-ray diffraction patterns of all the products indicated that the spinel concentrated was a ferroan magnesiochromite with rutile, ilmenite and hematite as impurities. Since all products were from a single pass, further processing can be expected to remove the impurity minerals and yield higher grade products. The material produced from the Murray Basin ilmenites in this study had similar compositions to commercial chromite ores, except for titania levels that were much higher. The high titania levels were due to residual rutile in the products, but it is expected that this can be removed with further processing. The mineral sand deposits in the Murray Basin are scattered over a wide area and the amount of chromite that may be produced from each of these deposits is unlikely to be sufficient to support an export market. Consequently, any chromite produced in the Murray Basin will most likely need to be processed locally to value added products for a niche market such as chemicals production. Keywords: Murray Basin, ilmenite, chrome spinel, roasting, magnetic separation, chromite ore

Jan 1, 2003

By T. Gerritsen, A. Matyas, F. Stober, I. Candy

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed. The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation.

Jan 1, 2004

By R. P. Mohring

The South African Coal Industry had its beginnings in the Eastern Cape in 1859 when coal was mined to satisfy the fledgling settlements in the Eastern Cape. The growth in the industry was relatively slow up to the early 1970s when, firstly, the export business was expanded coupled with a major increase in the quantity of coal converted to liquid fuels and utilized for power generation. To meet this increased demand the industry developed many new operations employing the latest mining technology and systems. Coal production in South Africa reached 204 million tons in 1996 and revenue from exports reached R8 billion making it the second-largest foreign exchange earner after gold. In his address Rick P. Mohring describes the role coal plays in the international energy scene and outlines South Africa?s position as a producer and consumer of coal, and the challenges facing the industry. A wide range of steam-coals are produced to satisfy both the local market (power generation, coal conversion and the metallurgical industry) and the export steam-coal market. South Africa is in a unique position regarding the export market as it is still a relatively low-cost producer and is geographically well-placed to play in both the European and Far East markets. There are, however, a number of challenges facing the industry. To retain our competitiveness in the international market, ways of minimizing the cost pressures caused by high-cost inflation, increased environmental protection obligations and a decreasing quality resource base need to be sought. Locally the coal mining industry has a major role to play in Eskom?s goal of reducing the real cost of electricity by 15% in the next three years. Safety and health, productivity and the adaptation of the latest technology are issues being addressed by the industry to maintain its dominant position within the South African economy.

Jan 1, 1997

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

Open cast mining has been practiced in South Africa since the late1970s under near ideal geotechnical conditions. In the past decade, with the exhaustion of the traditional South African coal fields, geotechnical conditions have deteriorated. In addition, the nature of the open cast coal mining industry is changing from the conventional strip mining of virgin coal seams to the extraction of underground coal pillars by buffer blasted highwalls. These industry changes have resulted in the need to re-examine the manner in which geotechnical engineering is applied to highwall design. This paper proposes a geotechnical design rationale for open cast highwalls. Furthermore, the rationale takes cognizance of the various geotechnical hazards associated with conventional strip mining and pillar extraction by buffer blasted highwalls. The need to use geotechnical domain models and blasting geotechnics, as proactive tools for rock fall reduction, are also discussed.

Jan 1, 2001

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By X. B. Zhao, J. G. Cai

The purpose of this paper is to incorporate the dynamic BB model of rock fracture normal behaviour into Universal Distinct Element Code (UDEC), and to conduct UDEC modelling to predict stress wave propagation across rock fractures. With the incorporation of new dynamic model of fractures, the UDEC is improved in the capability of modelling wave propagation across fractures. In this study, the case of normally incident P-wave transmission across a fracture is modelled, and the effect of dynamic normal behaviour of fracture is concentrated on. Wave transmission coefficient for wave transmission across the fracture with the dynamic BB model is obtained for various combinations of fracture dynamic parameters, as well as different wave amplitudes and frequencies.

Jan 1, 2003

By Z. G. He, S. H. Chen, P. Egger

A new model for hollow rock bolts which comprises rock material, hollow bolt material, bolt/rock interface, is developed on the base of the composite element method (CEM). The main advantage of the new model is that it can be incorporated into the conventional finite element analysis. So the mesh generation of bolted rock structures becomes more convenient and feasible, which is very important in the optimisation of reinforcement design: the mesh can be kept unchanged when the number and orientation of bolts are adjusted. The comparison of the calculation results with a conventional FE approach shows the robustness of the proposed method. Un nouveau modèle numérique de boulons creux comprenant la roche, le matériau du boulon creux et l’interface roche / boulon est développé sur la base de la méthode des éléments composites (CEM). L’avantage principal du nouveau modèle est la possibilité de l’incorporer dans une analyse aux éléments finis conventionnelle. Ainsi la génération du maillage d’une structure rocheuse ancrée devient plus simple ce qui est très important pour une optimisation du projet : en cas d’ajustement du nombre et de l’orientation des boulons, le maillage reste inchangé. La comparaison de résultats de calcul avec ceux obtenus par un code aux éléments finis conventionnel montre la robustesse de la méthode proposée. Auf der Grundlage der Verbund-Element-Methode (CEM) wird ein neues Modell für hohle Reibungsanker entwickelt, das den Fels, das Ankermaterial und die Kontaktfläche Fels / Anker umfasst. Der Hauptvorteil des neuen Modells ist die Möglichkeit, es in eine konventionelle FE-Analyse einzubetten. So wird die Netz-Generierung für verankerte Fels-Bauwerke einfacher, was für die Optimierung des Verankerungs-Projekts von Wichtigkeit ist: wenn Zahl und Orientierung der Anker variiert werden, bleibt das Netz unverändert. Der Vergleich von Rechenergebnissen mit solchen aus einer konventionellen FE-Rechnung zeigen die Robustheit der vorgestellten Methode.

Jan 1, 2003

By N. A. Barcza

This publication records the proceedings of the Tenth International Ferroalloys Congress, INFACON X, and the third INFACON hosted in South Africa. The Proceedings of the previous two South African congresses in 1974 and 1992 serve, as this volume does, as a valuable record of the papers presented at these important events. This publication comes at a time in South Africa?s democratic development where the theme ?Transformation Through Technology? is very appropriate. The ferroalloy industry has played an increasingly significant role in transformation and black economic empowerment in South Africa, particularly through the advancement and sharing of technology. INFACON X plays an important role in this process, and the stakeholders and organisers of this Congress are thankful for the opportunity to hold this event at this time of transformation in our country. The world of ferroalloys, as well as that of the steel and stainless steel industries, has continued to change rapidly. Recent innovations, better use of resources, increased awareness of environmental issues and ongoing efforts to improve occupational health and safety are among the topics addressed at INFACON X and in these Proceedings. The theme of ?Transformation Through Technology? has been chosen to reflect the regional and global developments in the ferroalloy industry, and the crucial role that technology plays. The Proceedings of INFACON X, the first Congress in Southern Africa of the new millenium, represent a milestone in the technical developments in this major global industry. It contains almost eighty papers in twenty Sessions, from authors in twenty countries, covering raw materials, reductants, energy, electrodes, refractories, furnace design, post taphole services, modelling, simulation, control, sensors, fundamental issues and the applications of ferroalloys as related topics. The major ferroalloys, namely ferrochromium and ferromanganese, are covered extensively in many interesting papers. This comes as no surprise, since South Africa is the leading producer of ferrochromium and also plays a major role in the supply of manganese ore and alloys. Papers on ferronickel, silicon and ferrosilicon ensure that all the large-volume ferroalloys are addressed. These Proceedings of refereed papers of high quality will serve the ferroalloy industry for many years to come, as has been the case with previous INFACON events. For the first time in the history of INFACON, the Proceedings will be available both in bound and in a searchable electronic CD-ROM format. We appreciate the time and effort that the authors and referees have devoted to making this publication a really valuable document. Their contributions are recorded for posterity and reflect the advancements they and their colleagues have made to benefit the ferroalloy industry. Without these ongoing improvements, the industry would stagnate and not fulfil its role in the advancement of mankind. All papers included in these Proceedings were peer-reviewed by at least two referees. About 130 referees were sourced internationally to fulfill this function, and their valuable technical and editing inputs are gratefully acknowledged. Finally, I would like to thank the Technical Programme and Publication committees, led by Dr. Lloyd Nelson and Dr. Noël Machingawuta respectively. Without the tireless efforts of these individuals and their Committee members, the technical programme and these Proceedings would not have been the success they certainly are.

Jan 1, 2004

By K. I. Afewu

A modified approach to the implementation of Gy?s sampling theory is discussed and used to design a procedure for sampling crushed gold ore feed to metallurgical process plants. The approach involves calibration of certain ore-specific parameters. These parameters were calibrated for two different crushed gold ores en route to grinding mills in process plants. The model predictions were compared with the predictions from Gy?s original model. Far smaller masses of samples are required by the modified model than by Gy?s model at the same relative variance. The representativeness of the sampling procedure if normally distributed errors are assumed was also calculated. These procedures and evaluations lead to significant savings on cost of handling and preparation of the samples and to a quantifiable degree of confidence in the analytical results for the process plant.

Jan 1, 1998

By J. Engelbrecht

South Africa?s re-entry into the fast moving and competitive global economy calls for some careful strategic planning and a good deal of co-operation between suppliers and end-users. The issues that need addressing are generally well known and include: ?South Africa was ranked 45th out of 46 i.r.o. productivity ?SMMEs contribute 1% to exports compared to 40-60% for the ?tigers? ?High unemployment ?Limited skills of the majority of workers ?Slow growth rate of the economy ?The vast majority of suppliers are not world-class ?The vast majority of suppliers are not export or marketing orientated. In order to survive, all parties, i.e. government, labour and business, will have to play their part.

Jan 1, 1999

By J. J. Cilliers, J-A. Lamamy, J. N. Rasera, K. Hadler

Production of oxygen on the moon can be achieved by reduction of lunar soil. One such reduction technology, hydrogen reduction, favours a high proportion of ilmenite in the feedstock. Ilmenite is present in lunar soil as a minor mineral phase, but it can be upgraded using electrostatic separation. This study presents the results of a preliminary investigation into the operating parameters and sensitivities of a free-fall electrostatic mineral separator for lunar applications. Samples of ballotini and ilmenite as well as simple binary mixtures of the two were tribocharged on copper and passed through a uniform electrostatic field. The field is varied to change the electrostatic force acting on the particles. The proportion of material reporting to the positive electrode collectors, negative electrode collectors or the central collector was measured to determine the separation performance. The data confirmed that the charge transferred from the tribocharger to each species is in agreement with the triboelectric series; ballotini was found to charge positively on copper and ilmenite negatively. Particle-particle contacts were dominant, however, resulting in a somewhat symmetrical particle distribution in the collectors. These findings indicate that the copper tribocharger design requires optimisation in order to substantially increase particle-wall contacts. Four binary mixtures with feed grades of ilmenite ranging from 5% to 20% were prepared and tested. This study found that a higher ilmenite head grade resulted in a higher concentrate grade (26.3% from a head grade of 20%) with low recovery (3.4%). In contrast, the lower feed grade resulted in a low concentrate grade but higher recovery. The mass yield of ilmenite was 1.4 times greater for the highest-grade feed than for the lowest. A subsequent study into the reprocessing of middling fraction found a nearly constant relationship between cumulative grade and recovery. This is the first investigation into the effect of feed grade on the concentrate grade and recovery for lunar mineral processing. Keywords: Lunar resources, beneficiation, electrostatic, SRU, ISRU

Jan 1, 2020