Search Documents

By H. Petersen

If a coal mine producing two hundred thousand (200,000) tons of coal per year could effect a 2 per cent decrease in the percentage of slack there would be an additional 4,000 tons of prepared coal produced. Most operators will say that these prepared sizes of coal are worth about $3.00 more per ton to them than the slack or in other words an additional $12,000.00 pier year profit could be made by a decrease of 2 per cent in slack. A large tipple with all the finest modern equipment of shaker screens, conveyors, box car loaders, etc., can only produce a grade of coal dependent upon the coal delivered by the mine car at the top of the tipple. In the mine, coal-cutting machines have been doing their part for many years toward decreasing the percentage of slack. There is therefore, only one phase of production left where real effective work can be done, that is, intelligent and constant supervision of preparatory work and shooting. The quality of coal is really entirely dependent upon the kind of coal produced at the face in the mine. Our problem is therefore, at that place. The writer is thoroughly convinced that with the proper placing of holes the use of correct amount of a suitable explosive, thoroughly tamped, with the bug dust entirely removed from the mining, a decrease in slack can be effected. We will take up this problem under five headings. First-The proper placing of bore holes. Second-The proper amount of permissible powder. Third-The proper loading and stemming of the shot.-Cushing shooting. Fourth-The necessity of removing the bug dust from the mining. Fifth - The - standardization of rounds. First-The Proper Placing of Bore Holes. The most important thing and the real secret of successful blasting of coal is the proper placing of the bore hole. This results in the correct balancing of the shot and the securing of the maximum efficiency of the explo¬sive. If you are operating a mine with a 6-foot coal seam, you most likely are using a 6-foot cutter bar on the coal cutting machines. You should use three holes to properly bring down the coal. (1) A center shot in the middle of the room drilled flat, or rather parallel to the mining-the heights of this hole will depend upon the top parting. If the coal is frozen to the roof, it will be necessary to have the hole as close to the roof as possible. If there is a free parting, the hole may be placed lower but not over twelve inches from the roof. (2)

Jan 1, 1925

Jan 1, 1988

By J. H. Emrick

When I was asked to read a paper to you, I wondered what idea I could bring before you which would be interesting and which would be helpful in your work in operating coal mines. The Institute has been studying ways and means of increasing the safety and efficiency of mine operations. Almost every subject along this line has been discussed from time to time. In thinking the matter over it occurred to me that there was one thing used by practically all coal mining companies in considerably large quantities and which in many cases does not receive the attention it should. It is the cutter bit placed in the cutter chains on coal mining machines. Coal mining machines have been repeatedly improved during the last twenty-five years until their efficiency and convenience have reached a high level. The generating units making electrical power to operate them also have been developed to a similar degree. This machinery has been in- stalled at a great expense to coal mining companies and the installation made for the sole purpose of pulling coal cutter bits through coal. Why not then give these cutter bits some attention so as to see that they do their work as efficiently as their driving and propelling units? The consideration of this question easily divides itself into three principal parts-First, the kina of steel out of which to make the bit; Second, the proper form or shape to give it; and Third, the tempering of the bit. Let us discuss them in that order. There have been tried at different times' various grades of steel for cutter bit uses. The cheaper steels, having a very low carbon content (.10 to .30 per cent carbon) have proved un- satisfactory because such steel cannot be tempered so as to produce a satisfactory cutting tool. Because of the low carbon content, it cannot be hardened to retain its cutting edge. It dulls quickly, bends easily on striking any hard obstruction in the coal, and so requires constant resetting to its original form. The high priced alloy steels when properly shaped and tempered will give a bit that would make a clean, even cut in the coal if no impurities were encountered. Such a condition is rarely found. Alloy steel is quite brittle and on striking impurities, such as sulphur balls or a sand spar, is readily broken and so the loss of material through these broken bits and the high price paid for it more than offset all the other advantages which this steel has shown in cutting. Experience has shown that steel having approximately .70 per cent carbon and from .25 to .35 per cent manganese will give the most economical results. Some mines have obtained better results by using a steel of slightly higher carbon content and in some cases a grade of tool steel has been used. The disadvantage of using a steel having too much carbon is that it can easily be spoiled in the black- smith shop by overheating. Steels having a carbon content of about .70 per cent have a sufficiently wide range of temperatures at which they can be forged and hardened so that with ordinary care and attention they are not likely to be burned. Steel of this quality, therefore, has been found to be the most practicable because of its reasonable cost, ease in working and tempering and general durability. In the early days of mining machines, comparatively few bits were used because each machine required but a few bits because there were but

Jan 1, 1925

Jan 1, 1980

[WILLIAM LITTLEJOHN President Castle Gate, Utah BENEDICT SHUBART Secretary-Treasurer 521 Boston Bldg., Denver, Colo. .JAMES DALRYMPLE Vice-President for Colorado State Office Bldg., Denver, Colo. HORACE MOSES Vice-President for New Mexico Gamerco, New Mexico .J. B. FORRESTER Vice-President for Utah Hiawatha, Utah P. H. BURNELL Vice-President for Wyoming First National Bank Bldg., Ogden, Utah EXECUTIVE BOARD COLORADO: J. B. DICK Walsenburg R. A. McALLISTER Trinidad NEW MEXICO: W. W. RISDON Albuquerque J. B. MORROW Dawson UTAH: CHAS. LEGER Rolapp R. R. KIRKPATRICK Sunnyside -WYOMING: F. L. McCARTY Rock Springs J. C. RAE Gebo]

Jan 1, 1924

By Sam Andrews

Mr. President, Officers and Members of the Rocky Mountain Coal Mining Institute: This is my first attempt to prepare and read a paper before your association. The Rocky Mountain Coal Mining Institute, I understand, was formed for the purpose of increasing knowledge relating to coal mining in all its various branches by study, research and discussion. In writing my paper, I have tried to be as practical as I can, at the same time, present my arguments so that they can be easily understood. When I use the word science, I mean organized common sense. I humbly ask my hearers to be a little patient, while I read my paper, and be "to its faults a little blind, and to its virtues a trifle kind". Western Europe is said to be the cradle of the coal mining industry. We are told that the Ancient Britons were acquainted with the use of coal long before the Romans invaded and conquered their country. The Romans were never too proud to learn from the outer barbarians, and possibly acquired the precious secret from them: We are told that it was not until the 13th century, that the coal mining industry, assumed any noticeable importance in Britain, and on the Continent. In the year 1259 Henry the 3rd granted a charter to the freemen of New Castle on Tyne, allowing them to mine coal. For a long time it was used in the arts and manufactures only, wood continuing to be the common domestic fuel. As has been the case with almost every great benefit, the introduction of coal as a fuel was stoutly resisted at first, and we find its use prohibited in the city of London in the reign of Edward II, by Royal proclamation ; which was soon discovered to be injurious and foolish, and consequently withdrawn. It is interesting perhaps, to know how this Royal proclamation was brought about. A lady of the Royal household was riding in her coach one day through a village in which coal was burned as a fuel, and she suffered such a cough by inhaling the coal smoke that she decided to call a council of suffragetts, who ultimately decided that the burning of coal was injurious to their health and complexion. They drafted out a petition and presented it to the king, who speedily issued the order that no coal was to be burned in the city of London. The penalty for disobeying this order was death by hanging. We are informed of one poor man who continued to burn a lump of' coal on his fire in winter time; he was arrested, sent to prison and condemned to death; the judge in passing the sentence solemnly stating that if he was not allowed to get a fire that was hot enough in this world, he felt that he surely would be allowed one in the next.

Jan 1, 1921

A great many questions were asked Mr. Bright, and Mr. Bright's opinion was given on a number of subjects. He spoke at length on spring suspension of locomotives, bringing out the necessity for better spring suspension due to heavier weights and higher speeds now developed. The subject of dynamic braking was brought up, and the opinion of the engineers present was that dynamic braking was not a desirable feature except where heavy, long, adverse grade is encountered. Mr. Goddard and Mr. Bright had a spirited discussion regarding ball bearings, bringing out the opinion of the meeting that ball bearings in motors are preferable to sleeve bearings, and the few failures so far encountered are due to improper application or insufficient size of bearing. Mr. Shubart brought up the question of locomotive speed, mentioning some high speed work on main haulage, also an interesting experiment in a large Eastern mine where very slow speed, 3 1/2 miles per hour, gathering locomotives were substituted for the high speed gathering locomotives with an increase in cars gathered and a material decrease in derailment and accident. Mr. Bright mentioned the improvement in gathering reels, and Mr. Shubart mentioned the safety in the use of the concentric cable in direct current, using the outer wire as the ground wire, so that in case of accident to the cable, the ground wire acted as a protector to the live wire, materially decreasing the danger of sparking. Mr. H. I. Smith of the Bureau of Mines brought up the question of explosion proof construction, and Mr.. Bright and. Mr. Shubart explained the construction adopted by two of the larger manufacturers. Experiment has shown that the force of explosion in motors due to gas does not exceed 150 pounds per square inch. All forms of screen or baffles have proven an actual source of danger, due to the collection of dust, usually soaked in oil, forming an active means of propagating flame, together with the fact that all these appendages are frequently left off when the motors are repaired. Modern construction eliminates all openings, screens, devices for stopping or extinguishing flame. The motor is made entirely enclosed, practically air tight, all joints are ground and all openings necessary for access and attention are closed by bolted plates. The case is made stout enough to withstand any interior explosions, and ample ribbing is provided for heat dissipation. Mr. Bright was asked regarding the use of contactor control. He replied that his company is now recommending contactor controls for series and parallel starting on all locomotives of 13 tons and over, and particularly on the tandem units that are now becoming popular in coal mining work. The question of dynamic braking and reversing was brought up and Mr. Bright explained that this made a very complicated contactor installation but they had

Jan 1, 1922

By C. E. Drennan

Your Chairman and the Program Committee have limited the time allotted to me, and so, with your permission, I will omit the preliminaries, and wade right into my subject. I believe I am safe in taking for granted that you are all agreed that electricity is the most feasible means of transmitting the power used in coal mining. If you are not, then the papers read before the Association in previous years have failed of their object. If you are so convinced, the only question is as to the choice between alternating and direct current, and the voltage. Fundamentally, this is primarily a matter of dollars and cents. With the sole exception of your trolley locomotives, there is no part of your equipment that cannot be operated as well on alternating as on direct current. With your pay rolls at their present high level and the efficiency of the labor you employ at the stage it now occupies, I believe you will agree, first, that everything possible must be done to increase the tons of coal produced per man employed; and, second, that ample power at all times must be available at every machine so that every one of your men can really get out a day's work without any avoidable delay. Speaking Electrically, all this means is a machine instead of a man wherever it is possible for a machine to do a man's work, and full voltage at the machine always, so that there can be no excuse for the work not being done promptly and efficiently-and dependably. The real reason for the selection of one kind of current or the other can best be understood by considering the formula which determines the size of wire required for transmitting electrical energy. The size of the copper required, and, consequently; its weight and cost, depends upon four factors: 1. The amount of energy or power to be transmitted. 2. The distance to be covered. 3. The percentage of loss allowed. 4. The voltage at the receiving end of the line. These factors enter into the problem to different extents, and, briefly, the size of wire depends directly upon the amount of power and the distance transmitted, and inversely upon the percentage of loss allowed and the square of the voltage. From this it will be seen that, with the amount of power and the distance fixed, if the loss is to be cut in two, the wire must be doubled with a given voltage, while if the loss remains constant and the voltage is doubled, the wire may be cut in four; that is, reduced 75 per cent in weight and cost. Now, standard motors are designed and recommended by their builders to run within a range of 10 per cent under voltage to 10 per cent above voltage - 440-volt motor, then, should preferably not be operated on less than 400 volts

Jan 1, 1923

Thomas J. LIEN RMCMI PRESIDENT 1997-1998 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 94TH Regular Meeting and Convention to be held June 27 thru June 29, 1998 Snowmass Village, Colorado

Jan 1, 1997

By John M. Jennings

The Hiawatha pitmouth is located at the head of the middle fork of Miller creek, at an altitude of approximately 8,100 feet. The coal is lowered to the tipple down a gravity tram two miles long, in 16 car trips which carry about 60 tons net. The average running time of the trip is about nine minutes. At the bottom of the tram there are two tracks for the loads and two for the empties. The trip, after being cut off the rope, is dropped by gravity onto a feeder, where the cars are uncoupled and fed one at a. time across the pitcar scales and into the dump. The dump is of the full revolution type, friction driven. On passing out of the dump the cars are returned by a kickback onto the empty car haul. They are caught at the bottom by a brake which consists of a pair of steel squeeze blocks operated by heavy springs. The empties are elevated to the double tracks, where the trips are made up. The feeder, scales, dump and empty car haul are all built on the solid ground of the hillside instead of being incorporated in one structure with the screening plant. The coal is dumped into a small hopper with a capacity of about 15 tons, whence it is fed by a reciprocating feeder onto a scraper conveyor which takes the coal over to the screening plant, a distance of 120 feet. This conveyor is 48 inches wide and travels at 120 feet per minute. The screen itself is interesting. It is of the Marcus Horizontal type.

Jan 1, 1925

Jan 1, 1990

TABLE ONE Accidents occurring in the Coal Mines of Utah by fiscal years: [Deaths ........................ Permanent total disability ...... Permanent partial disability. .... Temporary disability: .......... 28 days and over 14 to 28 days ............... 4 to 14 days ............... Under 4 days ]

Jan 1, 1922

Jan 1, 1931

By J. C. Rae

A Japanese mining engineer was given a year's leave of absence by his company and dispatched on a tour of inspection of all the principal coal mining regions of the world. He visited the New Castle region of England, Wales, Scotland, France, Germany and Alsatian mines, the underseas col¬lieries at Nova Scotia and Vancouver, and our own important fields of Illinois, Pennsylvania, West Virginia, Kentucky, Colorado, Utah and Wyoming. You are probably surprised to know that after seeing all these, he pronounced the Gebo mine of the Owl Creek Coal Company as the most interesting operation he had seen. The Gebo Mine is located about three miles west of Kirby on the Chicago, Burlington & Quincy Railroad in the Big Horn Basin region of Wyoming, 500 miles north of Denver and 200 miles south of Billings, Montana. The mine is working on a coal bed five or six to eleven or twelve feet' thick, dipping 22 to 23 degrees toward the northeast. The coal occurs in what is called the Eagle formation; and is found between two massive sandstones from 25 to 65 feet thick, which, weathering into bold', gray-colored cliffs, serves as a guide to the location of the coal bed. The deepest workings have an overburden of 800 feet. Cleavage planes of the coal extend at an angle of 45 degres to the pitch, and perpendicular to roof and floor. The coal itself is generally clean and not difficult to cut. It ignites readily from spontaneous combustion, however, which circumstance makes an ever-present fire hazard which must be carefully watched and guarded against. The coal is classed as sub-bituminous with analysis about as follows: Moisture 17% Volatile Matter 33% Fixed Carbon 46% Ash 4% Sulphur, about ½ % B. t. u. value a trifle under 11,000. It is known as Owl Creek coal, is one of the best domestic and steam fuels in the West, and is very popular in Montana, Idaho, Washington, Wyoming, South Dakota and Nebraska. While the coal slacks somewhat rapidly when exposed to the weather, it stores readily for months if placed under cover. On account of the somewhat isolated position of the mine as regards manufacturing establishments, there was a decided difficulty in disposing of slack, especially during the early years of the mine (1907 to 1914), and approximately 10 per cent of the entire product had to be wasted as slack during those years. This difficulty has been largely overcome since 1914, due partly to growth of manufacturing establishments in tributary territory, and also to enlarged transportation facilities. Also largely due to its isolated position, the mine has been compelled to use an extremely large proportion of box cars, much over 50 per cent of the product (in some years 75 per cent) being shipped in box cars, which, of course, entails extensive loading equipment and increases cost of loading. The output of the Gebo Mine for 1920 was 348,000 tons, for 1921, 273,000 tons; the rate of production during the year 1922 was over 1,700 tons daily, and 2,000 tons daily in January, 1923. The mine was developed by driving three openings straight down the pitch, the main slope being 12 to 14 feet wide and 3,000 feet long. A little distance from the surface a pair of level entries were turned right and left, known as the first East and first West. From these, rooms were driven up the pitch and chute mining attempted with only indifferent success: The failure of this rise-room method of mining was attributable to several

Jan 1, 1923

By J. F. McDermott

The problem of converting our raw coal, and especially those coals that are not suited for long storage, in other words soft, into a fuel which would be at once clean; of a high B. t, u. content and low ash, is one that has occupied the minds of many able chemical engineers and hydrocarbon technologists during the past few years. Low temperature carbonization is the present outcome of this line of research, and many methods have been evolved of recent years to turn out a serviceable, useful fuel, and at the same time, save the by-products. As most of the research and data within my experience and knowledge pertains to lignite or sub-bituminous coals, I will confine my remarks to coals of that character and grade: I might say that Colorado coals, commonly called lignite, are not in reality true lignite, but are sub-bituminous, although I have in my possession an analysis of a Colorado coal which shows a moisture of 17 per cent, volatile 31.5 per cent, fixed carbon 28.8 per cent, and an ash of 22.7 per cent, and B. t. u. less than 8,000. Even this, though useless for domestic or indeed industrial purposes, could not be classified as true lignite. However, for the purposes of this paper I will refer to these coals as lignite. Two thousand pounds, or one ton, of raw lignite carries about 20 per cent moisture. This, of course, varies in some coals, but is, I believe, a fair average. For carbonization purposes this is usually dried to a 5 per cent moisture, therefore leaving but 1,700 pounds of coal to be placed in the retort. From present knowledge, and with the average process of carbonization, 70 per cent of this coal will come out carbonized, or 1,190 pounds, to which is added about 10 per cent pitch, which is fried out as the coal passes through the retort, and which is used as a binder, making a total of 1,360 pounds of coke or carbonized coal. This is usually in appearance a dark colored, rather porous coke of about the size of pea coal. It burns without smoke and have a very high B. t. u. content. According to most authorities on this subject, carbon, hydrogen, oxygen, nitrogen, sulphur and ash constitute the only elements on which carbonization value of a coal depends, and of these hydrogen is the most important. It is claimed the value of a coal for carbonization purposes may be roughly surmised from the hydrogen content. If this is promising, that is, showing an available hydrogen content of from 3 to 5 per cent, the coal should be given a careful ultimate analysis. Should the seam, as often happens in lignite coals, show varying bands of coal of different structure or appearance, samples should be taken from each band as well as a gross sample taken down the face of the seam in the usual way. This is in order to determine what part of the seam is most promising for by-product processes. A seam showing a high nitrogen content adds to the attractiveness of the coal in carbonizing as; if available nitrogen is 2 per cent or better, it should give a very high ammonia yield.

Jan 1, 1923

[ ]

Jan 1, 1997

Jan 1, 1959

By S. R. DeBoer

A study of Western cities reveals the fact that a city where people make their homes for permanent residence is always a city with, well-shaded avenues, with parks and playgrounds; in other words, a beautiful city. On the other hand, the average city that lacks these qualifications is usually a city of transient population. Many of our Western cities must be classified as such. Their inhabitants live in such a city only to the time that they will be able financially to retire from business and go to one of the other types of cities to live; or until opportunity offers itself for a position or a job in such a city. I believe that our Western coal camps could benefit by this truth. If conditions can be created in the camps that will encourage the workers to settle permanently or for a long time at least in the town, it would greatly aid in stabilizing employment. By the term "workers" I do not mean the pick and shovel men alone, but everybody from the superintendent or the manager down; for the educated part of the population suffers probably greater from a desire for better surroundings than the less educated part. Modern City Planning tries to show the way for more attractive towns; for more practical towns also, and at less expense. The grid-iron system of street planning is slowly being replaced by one that fits the contours of the site. Instead of streets that are cut through the hills and built over the valleys to get practical grades, it tries to show how these streets can be made to fit the ground and produce better traffic lines; greatly more attractive streets; better building sites and lots, and all of this at less expense. A well-planned town of this character should have as its nucleus, a central square around which the main stores and business houses are grouped. The main building of this group should be the church, the community meeting place, city hall or such other buildings of a public or semi-public character, that are imposing enough to add interest to the square. From this central square, streets should be built to radiate out in all directions, more or less like a spider-web. The main lines of these streets should be reserved for traffic purposes and they should be wide, for the town may grow into a city, and they should be direct, connecting the town center with outlying points at the shortest and easiest possible line. Between these radiating streets should be residential streets of narrower width and arranged in such a way that fast through traffic cannot pass over them and make them unsafe and unsanitary for family life. Following up the comparison with the spider-web, the town should have circular streets, encircling the whole town with rings at various distances out, along which circular lines parks should be located. In the West, where the need for shade is so great, the town should surround itself with a belt of forest trees. Such a forest belt would break the winds and shelter the town, and also make the whole town a cozier, nicer place to build a home in. A forest belt of this kind does not necessarily mean a great layout of money. Trees can be planted small and at little cost and a carefully studied irrigation system will make the maintenance cost small. If the town has any places of natural beauty they should be carefully preserved and made accessible. Natural parks of this type will often take the place of the artificial parks of large cities, and at no expense to the community. Playgrounds, a swimming pool, either of concrete or a sanded beach on a lake; a place for all to go skating in winter; a hill for sledding in

Jan 1, 1924

Jan 1, 1929

SECRETARY SHUBART: This letter will not surprise you. (Reads) UNITED STATES DEPARTMENT OF COMMERCE Bureau of Mines Washington Sept. 4, 192G. Benedict Shubart, Secy, Rocky Mountain Coal Mining Institute. Denver, Colo. Dear Sir: "Sorry not to be able to be with you but since my function in the Institute has been largely along the line of `stirrer up of trouble' (of course always with the aid of Dalrymple), I do not wish to fall from grace now so am sending you a pamphlet on the last page of which is a' tabulation as to accident indices of various coal mining states and it seems to indicate that the states comprising the Rocky Mountain Institute have the poorest accident record of all the states producing coal. "It seems to me that even allowing for possible deficiencies in connection with placing accidents upon basis of hours of exposure, our western states need to `tighten up' as to safety practices, hence I hope that the Safety Committee report will be both drastic and progressive and that western coal mines apply the drastic proposals in addition to approving them as the policy of the Institute. Why wouldn't it be advisable to have a committee appointed to ascertain why the safety record of the states comprising the Institute is so bad as to coal mines? Wishing the Institute all kinds of success." (Signed) D. HARRINGTON. SECRETARY SHUBART: He encloses this pamphlet issued by the Bureau of Mines. On the back of it is this table; and it is a fact that the Rocky Mountain States are down at the lowest in almost every case, at the lowest point, with the highest accident rate in almost every kind of accident. Maybe he is wrong; maybe he states this for reasons. That is a rotten looking table for us.

Jan 1, 1926