Search Documents

Improve underground mine roof bolt support systems by alleviating problems associated with certain ground support systems currently being used. Approach Convert a passive resin-grouted roof bolt system into a uniform, tensionable roof bolting system. Background Resin-grouted roof bolts are one of the most common forms of ground support in U.S. underground coal mines. These support systems can be installed with a full-column of grout and be loaded with subsequent roof movements after installation. This is called a "passive" support system. An alternative to the passive support system is the mechanically-anchored, tensioned roof bolt system. This system is installed with resin grout. This system is designed to load or tension the support during installation by using a mechanical anchor, coupling, or threaded nut after the resin has properly cured. It is called an "active" support system and is used extensively for improved strata control in a laminated geologic deposition or in difficult ground conditions. To ensure that active bolts have been properly installed, the bolt loads must be checked by using a torque wrench or other suitable equipment. Unfortunately, this practice presents potential safety hazards and has limited accuracy. Laboratory and field experiments also reveal that the torque-to-tension ratio developed on active support systems can vary by 50% from bolt-to-bolt. Variations in bolt load installations can induce stress concentrations and lead to roof degradation or failure.

Jan 1, 1991

By John A. Organiscak

Laboratory and underground studies were conducted by the Bureau of Mines to evaluate the effectiveness of a water-powered scrubber and a brattice partition to create a clean split of air for longwall workers at the tailgate. In simulated laboratory tests, the system was very effective in creating a clean split of air. Observed system efficiencies were 74 and 84 pct with induced airflows of approximately 2,000 and 2,500 cfm, respectively. Underground evaluations indicated that the system was capable of reducing respirable dust at the tailgate. The first underground evaluation resulted in protection efficiencies of 30.7 and 42.5 pct at scrubber water pressures of 150 and 450 psig, respectively. A 33.7-pct protection efficiency was observed in the second underground evaluation with a modified partition and the scrubber operating at 250-psig water pressure. To be most effective, the system should have the scrubber operating at a flowrate of 10 gpm at 500 psig to deliver a maximum quantity of cleaned air behind a well-sealed partition.

Jan 1, 1983

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum, The economic development of the country depended on the production and export of crude on. Output was estimated to be 49 million barrels in 1985 compared with 56 million barrels in 1984 and 47 million barrels in 1988. The country's only refinery consumed approximately 12% of the daily production of crude oil while operating at slightly over 50% capacity. The refinery output, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economic prospects were heavily dependent on the oil sector, which bad been responsible for the recent strong growth in the economy. The country consistently sought to avoid the problems associated with an overdependence on oil and followed a relatively broad-based development strategy, using oil revenues to sustain and encourage growth in other sectors. Approximately 75% of the gross domestic product (GDP) was attributed to the mineral industry in some form. GDP growth was approximately 6.5% during 1985.

Jan 1, 1987

By F. W. Hoertel

Near-optimum parameters were determined by the Bureau of Mines for vapor deposition of rhenium on heated copper substrates by hydrogen reduction of rhenium hexafluoride (ReF6). High-purity deposits of nearly 90-percent theo¬retical density were obtained with the reaction chamber at 250° C, with an H2 to ReF6 volume ratio of 25 to 1, and with an ReF6 flow rate of 5 grams per hour. Some rhenium deposited as a loose, black powder. When the established near-optimum parameters were carefully followed, this could be minimized but never completely avoided. Varying the reaction chamber pressure, both above and below atmospheric, yielded excessive quantities of rhenium powder. Deposition efficiencies, based on only the coherent metal, ranged between 70 and 75 percent. Massive deposits contained only spectrographic traces of impurities. The average microhardness (Knoop, 100-gram load) of vapor-deposited rhenium was 907. Limited research on the deposition of rhenium-tungsten alloys by reduction of the mixed hexafluorides produced deposits in which linear composition gradients were pronounced; this nonhomogeneity was attributed to the wide variation in optimum hydrogen-reduction temperatures of the two hexafluorides (250° C for ReF6 and 550° C for WF6). Using deposition temperatures between 250° and 550° C did not eliminate the composition variations.

Jan 1, 1967

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity, On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can riot be designed to be 100 per cent efficient' and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the Computed figures of heat requirement Per barrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil. The consumption of natural as fuel at refineries has declined since 1927, but this has been more than compensated by a rapid increase in the use of refinery or still gas. The total consumption of oil as refinery fuel in 1930 was not much below the 1925 total, but the consumption of coal has declined rapidly, so that in 1930 liquid and solid fuels contributed only 56 per cent of the total heat units- utilized at refineries as compared with 77 per cent in 1925 (see fig. 2).

Jan 1, 1931

By Suresh K. Bhatt, Gary L. Mowrey, Timothy R. Rehak, David K. Ingram

Coal and nonmetal mining used about 4.3 billion pounds of explosives and blasting agents during 2001 in the United States. A major part of this consumption was related to surface mining. Mine Safety and Health Administration accident data indicate that flyrock and lack of blast area security were the primary causes of blasting-related injuries in surface mining. Fatal injuries due to lack of blast area security were primarily caused by failure to clear blast area or inadequate access control to the blast area. At a coal mine, a neighbor walked into the blast area and was fatally injured. The blaster could not see the victim entering the blast area from the firing station. In another case, a passenger in a vehicle was fatally injured by flyrock because highway traffic was not monitored during the blast. In another example, a dozer operator entered a blast area due to lack of access control. Several fatalities resulted from using inadequate or no blasting shelter. A crane operator was fatally injured while standing in the open about 120 ft from the blast site. In another instance, a helper, standing about 150 ft away from the edge of a blast, was fatally injured by flyrock. In a limestone mine an equipment operator was fatally injured while guarding access roads in a pickup truck. This paper briefly describes six representative fatalities due to flyrock and lack of blast area security in coal and nonmetal mines. Several mines were visited to collect information relative to working practices aimed at mitigating blasting hazards. Salient information obtained through these visits is presented.

By L. E. Jackson, E. W. Dean

One of the refining processes to which lubricating oils are frequently subjected effects a reduction in content of paraffin wax. The actual treatment usually involves chilling and filter pressing; the most important result accomplished from a commercial point of view is lowering of the ""cold test"" of the oil. The Bureau of Mines has recently had occasion to ascertain the effect of changes in paraffin wax content upon the viscosity of oil and has conducted a series of experiments described in the present report.Object of the present investigation:The Bureau of Mines has devised and is using a method for the analysis of crude petroleum* which includes determination of the viscosities of lubricating oil distillates. The Bureau method does not provide for preliminary removal of paraffin wax, and it has seemed advisable to determine whether this omission causes any important variation from the results that would be obtained through commercial refinery processing. It was also thought that the present tests, though limited in scope, might be of some practical value in indicating the general effect of paraffin content upon one of the most important properties of lubricating oil.Experimental procedureA five-gallon sample of Pennsylvania crude petroleum was distilled at atmospheric pressure until 50 per cent of the charge had been vaporized. Two liters of the residuum was distilled at a reduced pressure of 40 mm. (absolute) and cuts were separated that came over between the temperature limits of 250° to 275° C. (462° to 527° F.) and 275° to 300° C. (527° to 572° F.). The viscosities of these fractions were determined and they were subsequently subjected to treatment that removed successive percentages of paraffin wax. Viscosity temperature curves were determined for the oil obtained after each removal of wax.

May 1, 1921

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

To develop a reliable, remotely-controlled, mobile roof support to eliminate the need to set posts, cribs, or props while extracting coal pillars. Approach The primary danger during pillar extraction is premature caving of the mine roof. The roof must cave predictably and dependably to ensure the safety of miners. Support during retreat mining is usually obtained by setting posts, cribs, props, roof bolts, or a combination of these devices. These are set manually by miners in the working area. To help minimize the danger to mine workers and to equipment posed by premature falls, the Bureau of Mines developed the mobile roof support (MRS) system to secure the roof during pillar extraction. How It Works The Mobile Roof Support (MRS) is eight-feet-wide, ten-feet-long and five-feet-high, with twelve inches of ground clearance. It is ruggedly built and exerts less than 20 psi ground pressure. The MRS is powered by a 40-hp, 460-v AC permissible motor. The reversible, variable tram speed is 80 ft/min on a 20-percent grade. It is tire-mounted, has a trailing cable, and is remotely controlled either by a radio or a tether communication cable. The machine carries four 50-ton jacks which serve as props for working heights from seven to fifteen feet. Two jacks are chassis-mounted and two are on swing arms. Each jack has a cap which distributes the roof load to three paints. The swing jacks form a breaker row to stop falling roof and prevent caving Into the work area. One jack has a visual load indicator and a second is wired to the machine lighting system. Blinking lights indicate when the preset loading is being exceeded. In the case of excessive loads, an ability to remotely jettison either or both swing jacks has been incorporated into the system to permit removal of the MRS while the roof is still supported.

Jan 1, 1985

By William A. Hoffman

In This Chapter [MSHA regulations for coal mines MSHA regulations for metal/nonmetal mines OSHA regulations for tunnel construction Types of respirators used in mines and tunnels Filter materials and filter efficiencies Donning, seal checking, and maintenance Filter service life and Respirator information resources] In many cases, engineering controls are not adequate to achieve satisfactory dust levels, so respirators must be used. This chapter explains the Federal regulations governing the use of dust respirators in mines and tunnels and describes the most common dust respirators used. Filter materials and filter efficiencies for respirators are discussed. This chapter also gives some guide-lines for respirator use and recommends sources for more dust respirator information. Respirator effectiveness in reducing dust exposure usually exceeds the effectiveness of most engineering control methods. RESPIRATOR REGULATIONS [Different regulations govern respirator use in coal mines, metal/nonmetal mines, and tunnels under construction.] Coal mines under Mine Safety and Health Administration (MSHA) jurisdiction. Coal mine operators are required to meet dust standards using only engineering control methods. Typical engineering control methods include ventilation and water sprays. Respirators are not regarded as an engineering control method, so respirators cannot be used in lieu of engineering controls.

Jan 6, 2003

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

By S. L. Payne, E. F. Foerster, C. W. Schultz, G. R. Zellars

The vapor pressure of copper in a series of liquid copper - nickel alloys was determined by the carrier gas method . The activity and activity coefficient of copper were calculated over the entire range of alloy composition . These data show a slight positive deviation from ideal behavior . The activity coefficient of copper was highest ( 2.10 ) at 0.05 mole fraction copper and approached unity at concentrations above 0.85 mole fraction copper . The results for nickel were calculated from the copper data by the graphical integration of the Gibbs - Duhem equation .

Jan 1, 1964

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By Robert C. Hickman

"INTRODUCTION The Big Four fault and the Sandy Creek fault, with several cross faults, traverse the Stalion-Curnel fluorspar prospect in a northeasterly direction. The Big Four mine, about three-quarters of a mile northeast of the prospect, is the only active mine in the immediate area.A resistivity survey was made of a portion of the prospect by the Division of Geophysical Exploration, Bureau of Mines, in May and June 1946. As a result of this survey, five holes were drilled by the Bureau of Mines during the period from October 8 to December 16, 1946. Two Longyear No. 12 Junior Straitline diamond drills were used for the work.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the supervision of Mitchell H. Kline, chief, Raleigh Branch, Mining Division."

Mar 1, 1948

Reduce spillage hazards and contamination when adding hydraulic nil to mining machine reservoirs. Approach An easily transported module, that delivers hydraulic oil directly into mining machines, was built and tested. How It Works The Hydraulic Oil Delivery Module is carried, from the oil storage area to the equipment needing oil, in the bucket of a scoop or other utility vehicle. Oil is pumped into the module reservoir from storage, or out of the module reservoir into the machine being serviced, through a long hydraulic hose. During long-term testing, the 115 foot long delivery hose made it possible to replenish the hydraulic oil in mining machines at the face with only limited interruption to the mining operation. (Figure 1 shows one! version of the module.) The compact Hydraulic, Oil Delivery Module consists of: an oil reservoir: a pump driven by a hydraulic motor; two high pressure, low volume oil lines, filters; and a low pressure, larger capacity delivery hose equipped with quick-connect-couplers. The high pressure oil lines are connected to the scoop's hydraulic power takeoff, which supplies the power to pump oil in or out of the module reservoir.

Jan 1, 1977

By Alan H. Goode

As part of the Bureau of Mines program to broaden utilization of abundant low-quality mineral materials, the Tuscaloosa Metallurgy Research Laboratory conducted beneficiation studies on two Alabama clays. The main purpose of these studies was to develop improved plasticity and green strength in both clays and compare these improved properties with those of a typical ball clay. Whiteness of the clays was also considered. The results indicated that by adjusting the pH of the kaolin to approximately 9, a substitute for ball clay could be obtained. The investigation also showed that by a combination of attrition grinding and sodium dithionite leaching to remove iron, the underclay could be upgraded to a ball clay material.

Jan 1, 1975

By L. D. Gehi, A. W. Khair, M. Ahmad

"Bit wear presents problems to mining operations because it affects both productivity and economics. Most bit research deals with energy requirements and energy dissipation mechanics for ideal fragmentation during the cutting process.Mechanical cutting leads to dust generation. Past studies involving dust generation due to bit wear concluded that dust concentrations increased considerably after a 7% bit weight loss: leading researchers recommend that the bits be changed at that point.Bit wear is affected by three factors: machine operating parameters in-situ mining conditions and rock properties. Operating parameters such as the depth of cut tool material spray position and the drum's rotating velocity are very important and have a definite impact on bit wear.During the mining process the amount of rock in coal and the strength of that rock is important as abrasion and adhesion take affect. Diffusive wear or deformation becomes dominant only when the temperatures exceed critical. Temperatures rise as a function of drum velocity rock properties and the cutting tool itself.Miner bit surveyIn this study, 15 mines were surveyed, and of those six responded for nine seams. The survey reflected a wide range of information about coal production and bit consumption from continuous miner sections. Also used bits were collected to get first-hand information to analyze wear."

Nov 1, 1995

"INTRODUCTIONThe information compiled in this volume initially formed the response by the Generic Mineral Technology Center for -Respirable Dust (GTCRD) to a review of its research and technology transfer programs performed in 1990 by the Advisory Committee on Mining and Mineral Resources Research. This review for each mineral technology research center is accomplished, as required of the Bureau of Mines by the House/Senate Joint Conference Committee, through site visitation to the research institutions of the GTCRD and an in-depth questionnaire. The information provided by that questionnaire becomes an important factor in their recommendations concerning future directions of the program.The site visitations took place during January and February 1991 at the Milton S. Hershey Medical Center~ The Pennsylvania State University, West Virginia University, University of Minnesota, and Michigan Technological University, in addition to an in-mine visit conducted at the Loveridge Mine in West Virginia. The questionnaire was prepared and made available to the Advisory Committee and the Research Council for their review at the GTCRD annual project review meeting in Hershey, Pennsylvania, in April 1991.The comprehensive nature of the questionnaire and the scope of the information contained therein make it an excellent retrospective of the Center. Having a clear vision of where the Center has been and knowing where it is now helps to guide it into the future. It is believed that such a detailed view of the Center's facilities and research program will be of value to Center personnel and Advisory Committee members. Each aspect of the questionnaire was examined, answered in detail and documented thoroughly. With the completed questionnaire as a guide, this review of the Center's activities provides an update to Respirable Dust Center Research Program Review 1988, published in 1989 as the seventh of the Generic Mineral Technology Center for Respirable Dust volumes. As does that volume, this review presents the complete General Mineral Technology Center questionnaire, with the GTCRD's expanded responses and supporting documentation appended. An examination of the research program, Center personnel currently active on GMTC projects, the number of graduate degrees granted with GMTC supports GMTC publications, the degree of individual interaction, technology transfer activities, the reference center, GMTC equipment and facilities, and envisioned plans for future research directions provides updated information in these areas. In addition, this year, information has been included to demonstrate the interaction between the Center's goals and its research projects, with thorough consideration of actual research needs as specified by the National Academy of Sciences. This volume serves as a review of the years 1989 through 1990, the sixth and seventh years of the Center's operation."

Jan 1, 1990

By Eric Cather

A mineral investigation of prospects in the Sawtooth Mountains B Wilderness Study Area (WSA) by the U. S. Bureau of Mines in 1983 revealed none had mineral production, resources, or development potential. The area is underlain by tonalite and smaller amounts of schist, One developed prospect and one prospect pit are in the WSA. They are in schist similar to host rock which has yielded gold in nearby mining districts, Sand and gravel deposits in the WSA are large but too far from markets to be considered resources. No energy (oil, gas, coal, or geothemal) resources were identified in the USA.

Jan 1, 1984

By Robert P. Vinson, Kissell. Fred N., Edward D. Thimons

"The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.INTRODUCTIONAny location in a coal mine where 5 pct or more of methane is present constitutes a potential site for an explosion and roof cavities are likely locations. Unfortunately, little is known about the buildup of methane in roof cavities. Some research has been done using scale models where no air flows past the cavity so that methane disperses only by diffusion (5) 4 a rare situation in mines.No known cavity-model investigations have been made that simulate air and methane flow conditions normally encountered underground. These Bureau of Mines studies were undertaken to determine the extent and manner of methane buildups in coal mine roof cavities with air velocities in the range normally found in coal mines and with various methane emission rates."

Jan 1, 1978