Search Documents

By C. W. Owings, J. J. Forbes

"INTRODUCTION The recent coal-dust explosions in Illinois and Indiana have again brought forcibly to the attention of mining men the fact that mines which liberate little or no methane can have widespread explosions, if dry and dusty conditions exist and if adequate measures are not taken to control the dust hazard by rock dust¬ing or use of water.Even though rock dust has been used more or less extensively for more than 20 years as a means of limiting or preventing coal-mine explosions, many mine operators have requested information on rock dusting and means of allaying coal dust at its source. The purpose of this circular is to summarize available information on these two methods.COAL MINES TO BE ROCK-DUSTEDAll nonanthracite coal mines must be rock-dusted, except those mines or locations in a mine that are too wet or too high in incombustible content to propagate an explosion.Coal dust that contains 20 percent or more moisture may prevent ignition or propagation of an explosion. Such dust can be molded in the hands, and under such condition the roadway would be considered muddy. Mine dust that is only damp is not wet enough to prevent propagation of an explosion. Beads of water standing on accumulations of dust are not indications that the dust is wet. Only those mines or locations in a mine in which the coal dust can be molded in the hand need not be rock-dusted."

Jun 1, 1947

The investment involved in any communication system represents a considerable sum. Even though it is desirable that the system work properly each and every time it is called into use, some failures are bound to occur. Most failures, however, and especially those that occur most frequently, are due to poor installation techniques. An extra hour spent at an installation site can save many maintenance trips and many frustrating hours of system troubleshooting. Typical faults likely to cause communication outrage are Pager phone systems Poor splices aggravated by corrosion. Strain relief not provided. Drip loop not provided. Incorrect branch connections. Overloading the circuit. Poor battery connections. Improper wire size or type. Lightning strikes. Improper placement of wire runs. Carrier phones Mounting transceiver near load resistors or other sources of heat. Tracks not electrically bonded. Cable abrasion due to poor mounting location. Disconnected battery. Poor mechanical installation. Each installation should be well planned. After an installation is completed, the technician should ask the question, "What can go wrong with this unit or line?" Remember the adage, "Whatever can go wrong, will." Preventive measures taken during installation will pay off in the long run. 6.2 Pager Phone Installation The pager phones used in many underground coal mines are battery-operated, party-line telephones with provisions for loudspeaker paging. The system is usually two-wire, nonpolarized, and operated by self-contained batteries. Many of the individual units are certified as permissible. 6.2.1 Mounting Pager phones are designed to be mounted on an upright support at the desired location. For convenience, the phone should be mounted 5 feet above the floor where there is no obstruction to using the handset or removing the cabinet front cover for servicing or battery replacement. In low-coal situations, a suitable height for installation should be selected convenient to the normal operator's position at the site selected. About 12 inches of free space on each side of the phone should be provided for cabinet access. The phone should be protected against direct exposure to dripping water and should not be allowed to rest in a puddle of water. The mounting location should be convenient to a work location and have a safe, unobstructed area for a worker to stand and use the phone. The phone must be in a location where the worker will not be in the path of moving vehicles or falling debris. Each telephone is normally well insulated, but it is still good practice to provide an insulating mat or dry planking for the user to stand on.

Jan 1, 1984

By R. Karl Zipf, Christopher Mark

Highwall mining continues to grow in importance as a coal production method from U.S. surface mines. It may account for as much as 4% of the total U.S. coal production, according to one recent estimate. Analysis of Mine Safety and Health Administration (MSHA) accident and injury statistics shows that, overall, highwall mining has maintained an admirable safety record. Its fatality and injury rates are comparable to those for other surface mining methods, and are significantly lower than those for underground mining. No mining method is risk free, however. Highwall mining injuries have been associated with handling materials, slips and falls, machinery, powered haulage, and other types of incidents. But perhaps the greatest risk, to both personnel and equipment, is from ground control. The two most significant ground control hazards are rock falls from the highwall and equipment entrapment underground. Highwall Stability Ensuring highwall stability through proper ground control engineering is of paramount importance to safe highwall mining operations. The only fatality to occur during the last five years at a highwall mining operation was due to highwall collapse. There have also been numerous near-misses, several of which have involved extensive damage to equipment. In the central Appalachians, where the majority of highwall mining occurs in the U.S., hillseams are the most prominent geologic structures that affect highwall stability. Hillseams (or mountain cracks) are near vertical fractures in the rock that are formed in response to natural weathering and erosion of hillsides. They extend hundreds of feet down from the surface. They typically run parallel to the hillside, but they can also extend across narrow points or ridge lines. The hazard arises when rock slabs that form along the hillseams detach and fall away from the highwall face (See Figure 1). [ ] Unfortunately, it is impossible to control the location of hillseams or reliably detect their presence within a highwall. There are, however, a number of measures that can be taken to minimize the risk of failure associated with hillseams: Planning-Most operators choose to skip those areas of the highwall where a prominent hillseam daylights (See Figure 2). Existence of such areas is known for several weeks in advance of highwall mining; therefore, planning engineers can adjust the layout of highwall mining panels to locate barrier pillars within areas of questionable highwall stability. [ ] Inspection and monitoring-Daily inspection of the benches above the active highwall mining area is a prudent precautionary measure. A crack in a bench immediately above a highwall miner is shown in Figure 3. Simple displacement monitors may be useful for detecting movement along cracks that may precede a significant life-threatening failure. New tools, such as slope monitoring radar, may also prove useful in detecting motion of the rock slopes above active highwall mining operations. Good blasting practice-Most surface coal miners in the central Appalachians use pre-splitting and the familiar halfbarrels are routinely seen throughout the pits. Shorter delays along the face and longer delays between rows can direct more of the blast force parallel to the face, potentially doing less damage to the wall rock. In addition to pre-splitting, decreasing the burden, spacing and charge weight in drill holes close to the highwall will also decrease damage to the wall rock. Decreasing the highwall slope angle-Decreasing the highwall slope angle from 90° (vertical) to 70°-80°, especially in areas of known hillseam concentration, could eliminate the hillseam hazard (See Figure 4). Angled highwalls are routinely employed in many Midwestern surface mines and in some

Utilize innovative processing technology to prepare high-purity, ultrafine advanced ceramic powders with little or no contamination occurring during the milling process. Advanced ceramic materials made from these powders could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. Approach Modify and evaluate the Bureau's turbomill, developed earlier to grind a variety of ceramic raw materials (clay, mica, and talc), as a milling or size-reduction technique for hard and abrasive advanced ceramic powders, such as silicon carbide. Background Powders for producing ceramic materials, such as silicon carbide. silicon nitride, alumina, and zirconia, which arc being considered for use in severe applications requiring high-temperature and/or corrosion resistance, are very difficult to reduce to fine sizes for processing into finished parts. Traditional techniques of particle size reduction, such as ball milling and jet milling, are very energy intensive and/or slow. These traditional techniques often produce materials that have a nonuniform particle size distribution and are contaminated by the milling media or container.

Jan 1, 1989

By Ivette E. Torres

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom (London Metal Exchange) has been continued this year in tables 22 and 23. Time constraints have prohibited preparation of other price information that has appeared in this study in previous years. Users are urged to consult the 1993 U. S. Bureau of Mines publication Metal Prices in the United States through 1992, which gives an analysis of historical price series and trends, or the 1993 edition of Mineral Commodity Summaries for current U.S. prices on non fuel commodities, and to utilize U.S. Department of Energy sources for information on fuel material costs.

Jan 1, 1994

Allow miners to communicate via the pagerphone system when they are not near one of the phones. Approach A small lightweight pagerphone, having crocodile clips which pierce the phone line insulation, was developed. How It Works The Portable Telephone/Intercom is temporarily clipped onto an existing pagerphone line at any location, and operated like an intercom. It is riot necessary to strip the insulation from the pagerphone line to make the connection. In addition to the clips for connecting to pagerphone line, the Portable Telephone/Intercom consists of a small belt-carried control box, an ear-phone, and a bone-conduction microphone which is attached to the webbing in a miner's helmet. All together, these components weigh only 20 ounces including the batteries

Jan 1, 1977

Provide reasonably priced, reliable fire protection for loading shovels. Approach An automatic fire, sensing and suppression system using both dry chemical and Halon 1301 was developed. It is more rugged than similar industrial-type fire protection systems. How It Works Temperature sensors detect heat from a fire, and trigger the system. These sensors are located inside the machinery house and under the house and shovel frame where it rotates around the crawler chassis ring gear. An alarm is sounded, and extinguishing agents are released either in the machinery house or in the ring gear area. The system can also be triggered by a manual control. If the fire Is detected in the machinery house, all power is shut down to the motor-generator sets, ventilation fan, and all electrical controls. Doors are automatically closed. After a delay to allow time for the ventilation fan to stop, Halon 1301, a gaseous fire extinguishing agent, is released inside the machinery house until it reaches a concentration of about 7 percent. This concentration is sufficient to extinguish a fire, but isn't toxic to personnel

Jan 1, 1980

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

By W. E. Lamont

The Bureau of Mines studied the potential for recovering marketable barite concentrates that meet oil well drilling-mud specifications from barite waste pond materials. The study was conducted as part of the Bureau's research program to conserve domestic mineral resources by advancing mineral recycling technology. The samples, which were obtained from Georgia, Nevada, Missouri, and Illinois, varied widely in character, particle size, and barite content. The samples were treated with sodium silicate and sodium cetyl-stearyl sulfate and then floated. The flotation flow sheet was modified to reject barren coarse and/or slime fractions from some of the samples, and one feed sample had to be scrubbed prior to flotation to remove residual flotation reagents. The cleaned concentrates had BaS04 contents ranging from 95.0 to 96.9 percent, while recovering 81.2 to 95.9 percent of the barite in the feed. The specific gravity of each concentrate exceeded the specification of 4.2. The removal of the flotation reagents from the flotation concentrate was not investigated.

Jan 1, 1982

By E. E. Remmenga

Often a collection of analytical data, which should reasonably be expected to follow the normal distribution, contains too many extreme values, which the experimenter is inclined to eliminate according to some arbitrary procedure. The stepwise computer procedure described for this purpose is similar to many other truncation procedures; however, because truncation of a basically normal distribution causes a downward bias in the estimated variance, this procedure provides a graphical method to compensate for the bias.

Jan 1, 1971

By C. H. Elder

An experimental degasification program using a vertical borehole and vacuum pump to drain gas from the gob area of a longwall panel was successful at Bethlehem Mines Corporation, Cambria Division, No. 33 coal mine. Sixty-one million cubic feet of methane has been exhausted during a 9-month period. Daily production time in the panel increased as a result of lower methane levels in the returns. Removal of large quantities of methane in this way and the exclusion of it from the ventilating system will provide reduced cost in mine ventilation and provide a safer environment for the mine.

May 1, 1969

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTLATION NETWORK ANALYSIS

Jan 1, 1977

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

Reduce the dust levels to which jacksetters and helpers on auger mining sections are exposed by identifying viable, effective methods for control-ling respirable dust on these sections. Approach The Bureau of Mines con-ducted laboratory tests and respirable dust surveys to identify the factors that distinguish clean auger mining operations from dusty ones. Study Results Results of the Bureau's study revealed that ventilation is the most important element of auger mining dust control. The four must important venitilation parameters are airflow, curtain configuration, curtain setback, and curtain installation.

Jan 1, 1988

By J. E. Meacham

The U.S. Bureau of Mines investigated recovery of manganese from basic oxygen furnace (BOF) steelmaking slags because the slags represent a large potential resource of a metal for which there is no domestic production. BOF slags were leached using fluosilicic acid, a byproduct of the fertilizer industry. Manganese and iron were extracted as soluble manganous and ferrous fluosilicates while the calcium and magnesium remained in the tailings as insoluble fluorides. Treating the pregnant liquor with sodium chloride, precipitated sodium fluosilicate (Na2Sif6) which was recovered as a byproduct. Manganese and iron were precipitated as hydroxide-carbonate salts with the addition of sodium carbonate to the treated liquor. Recoveries for manganese and iron were 73 to 83 and 67 to 70 pet, respectively.

Jan 1, 1991

By C. M. Mason

Mechanical mining produces large quantities of very fine coal dust called float dust. The associated increase in hazard requires a reexamination of the Bureau of Mines method of evaluating the incendivity of explosives in coal dust-gas-air mixtures. A technique recently developed by Bureau of Mines laboratories for evaluating the incendivity of explosives in coal dust-air mixtures was applied, with modifications, to coal dust-air-natural gas mixtures. A series of permissible explosives were evaluated by this modified technique. Results indicate that the modified technique could be the basis of a more discriminatory procedure than that presently in use.

Jan 1, 1968