Search Documents

By Ruth A. Holmes

A Bureau of Mines method for recovering nickel, cobalt, and copper from low-grade domestic laterites is described, which includes the unit operations of solvent extraction and electrowinning. Previous Bureau work indicated that addition of Na2S04 (sodium sulfate) to the nickel electrolyte improved current efficiency in nickel electrowinning. The present study determines the compatibility of Na2S04 with nickel strip-ping in the solvent extraction operation of the Bureau method. The effect of adding 100 g/l Na2S04 on nickel stripping, phase disengagement, and pH was determined in comparative laboratory-scale tests. In continuous-circuit testing, Na2S04 reduced stripping efficiency to the extent that five, instead of four, strip stages were required for complete stripping of nickel from the loaded solvent. In tests made in a phase-disengagement cell that had a variable settler area, the addition of Na2S04 did not significantly affect phase separation characteristics. The pH of the nickel electrolyte in the temperature range of 20° to 65° C was also unaffected by the addition of Na2S04. An economic evaluation showed that the energy saved by adding Na2S04 to the electrolyte would more than offset the cost of adding another stripping stage.

Jan 1, 1983

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

By John C. Edwards

To have the capability to predict the development of localized spontaneous heating within a porous coalbed that is subjected to forced air ventilation or in an otherwise quiescent environment in which buoyancy develops, the Bureau of Mines developed three time-dependent mathematical models, which were used to calculate the temperature increase associated with chemisorption of oxygen by the coal. In each model, spontaneous heating is driven by an Arrhenius first-order reaction between the oxygen and coal. Two models are two-dimensional, and one is one-dimensional. In the first two-dimensional model, a constant-velocity forced convection airflow is specified; and in the other, buoyant flow is allowed to develop in the absence of forced convection. The third model evaluates the airflow from Darcy's law and a specification of the pressure at the surface of a one-dimensional porous coalbed. Numerical computations demonstrated how each model could be used to predict the onset of spontaneous heating when the porous coalbed was subjected to constraints of an imposed internal heat source or a high- temperature airflow. The effects of particle size and coalbed compaction upon spontaneous heating were examined with the third model.

Jan 1, 1990

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

Control respirable dust in underground coal mines through selection of optimum water spray pressures. Approach Through underground trials at longwall and continuous mining operations, the relationship between operating water spray pressure and respirable dust levels at the machine operator's location was determined. Defining the Application Water sprays are used for two significantly different control applications. On longwall mining machines, sprays are commonly installed both on the body of the machine and on the cutting drum. Sprays on the body of the machine are used to redirect dust which has already become airborne away from the machine operator. Each spray acts as a small fan, directing the primary airflow over and around the machine and towards the face, away from the operator. The energy of this system is directly related to the spray pressure. Higher pressures move more air, but care must be taken not to cause turbulence and boilout into the walkway. Sprays mounted on the drum are, effective at suppressing the respirable dust at the bit/coal interface and preventing it from becoming airborne. Again, these sprays must not impart excessive energy to the dust particles thus stirring up more dust than they suppress. While mounting sprays on the shearer drum is standard industry practice, there is no reliable technology available to successfully mount water sprays on the cutting drum of continuous miners. Instead, sprays are mounted on the machine body, close to the drum, and directed at the cutting head. This allows the water to reach the bit/coal interface and mix with the cut material. Here again, care must be exercised to prevent these sprays from imparting excessive energy to the dust particles and stirring up more dust than they suppress. These sprays can also cause dust "rollback" from the face, toward the operator, if operated at too high pressures.

Jan 1, 1986

By C. A. Komar

Hardness, tensile strength, and impact toughness of dry and brine-saturated sandstone specimens were measured at ambient, cryogenic, and elevated temperatures as a measure of the relative stability of reservoir rocks for subsurface disposal of liquid wastes. Hardness measurements were inconclusive. Tensile strength and impact toughness were significantly higher at -320° F than at ambient temperature, but were relatively unaffected at 700° F. Impact toughness was reduced by subjecting the specimens to three cycles of rapid temperature changes (thermal shock) over a 1,000° F range. Tensile strength of brine-saturated sandstone was less than that of dry sandstone. Based on results of the tests, reservoir sandstone likely would be stable if exposed to extreme temperatures of liquid wastes, although rapid changes in waste temperatures should be avoided.

Jan 1, 1971

Provide coal mine shafts/slopes with an optimum coal mine shaft fire and smoke protection system composed of reasonably-priced, reliable hardware. Approach Accident and injury data indicate that a relatively low percentage (5%) of underground coal mine fires occur in shafts or slopes. Nevertheless, shaft or slope fires are extremely serious because they block critical escape routes for miners. That also can happen when combustion products resulting from fires in other mine areas contaminate shahs and slopes. Seeking the optimum configuration for a shaft/slope fire and smoke protection systems, the Bureau of Mines gathered data on the performance of existing fire detection devices and signal telemetry systems In several mines, and analyzed the generic protection needs of the U.S. underground coal mining industry. The optimum system developed by the Bureau provided an adequate number of detectors, a wide area of coverage, and an extensive data acquisition, analysis, display, and storage capability. This system. recommended for fabrication and in-mine testing, consisted of a microcomputer-controlled master panel located in the test mine's slope hoist room, and four remote units. Two of the remote units were placed on the surface atop upcast ventilation shafts, a third was situated underground near the slope bottom, and a fourth was installed at the slope top in intake air.

Jan 1, 1986

By Fred N. Kissell

Tracer gas decay curves were experimentally obtained in a full-scale model coal mine working face area. The concentration of tracer gas was found to decay in exponential fashion but with a change in slope. This change in slope is attributed to eddy zones in the face area. A simple theory was developed that allows one to calculate the approximate amount of gas in the eddy zones and thus estimate the size of the eddy zones.

Jan 1, 1974

Lower the respirable dust exposure of longwall shearer operators by keeping the dust cloud confined to the face. Approach Change the location of face-side machine cooling, water sprays. How It Works The dust breathed by the longwall shearer operator is usually produced by the shearer itself. The dust cloud originates at the face, and the exposure of the operator depends largely on how quickly this cloud spreads into the walkway. Water sprays on the shearer body can have a large effect on dust cloud spreading. Results to date indicate that sprays can help confine the dust cloud to the face if they are carefully placed. Otherwise they can make dust levels far worse. The worst offenders are often face-side sprays used to discharge cooling water from the cooling jackets of the shearer motors. These face-side sprays set up an air circulation pattern as illustrated in the drawing. Air induced by the sprays to flow towards the face, raises the air pressure in front of the face, which causes the air flow to turn and then move back over the shearer, bringing dust with it into the walkway.

Jan 1, 1981

By Sivalingam Jeevan, R. L. McConnell

Ground check monitors may be made in several configurations. Each type has unique characteristics and provides different safety attributes when applied to different mine situations. In this paper, the monitor types are discussed in relation to the mine situations. It is shown that the selection of the monitor type can have a significant effect on the safety of the resistance grounded power system. The options are discussed, and the conclusion is drawn that only one monitor configuration can provide maximum safety. Unfortunately no monitors of this configuration are presently available. In addition, when the monitor capabilities and ground wire configurations are considered as a system, it can be shown that certain configurations will lead to maximum safety. This work was supported by U.S. Bureau of Mines grant G0144138.

Jan 1, 1979

By J. E. Chilton

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

By T. W. Beck

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter’s dust collection system. The laboratory tests evaluated the bag’s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector’s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector’s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers' equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer's manual and making the appropriate cable valve adjustments.

Jan 1, 1976

By Sathit Tandanand

Geological differences among various coalfields restrain the applicability of subsidence prediction using empirical approaches previously developed. The Bureau of Mines assessed data collected from 16 longwall panels in the Northern Appalachian basin. Attention was focused on the effects of rock lithology, excavation width, and panel depth on the subsidence factor. The results show that the subsidence factor can be expressed in terms of the width-to-depth ratio by a simple exponential equation, which has a coefficient tentatively considered as the subsidence index. This index varies with the lithology of a particular site, and can be expressed in terms of percent distribution of weak and strong rocks in the overburden.

Jan 1, 1982

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Its estimated recoverable reserves in Fayette County are between 670 and 800 million tons. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal.

Jan 1, 1977

By D. R. Tesarik, R. W. McKibbin, J. B. Seymour

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars),and biaxial stress meters (to measure stress changes in several support pillars and abutments). Two- and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 1995

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By J. E. Chilton, Jr. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995

By Ronald D. Hill, Elmore C. Grim

The United States is richly endowed with mineral resources. However, mineral recovery by its very nature, involves a destructive process, Figures 1 and 2. In the past, mining practices were all too often conducted with the purpose of removing minerals by the simplest and cheapest method possible, without plans for the preservation of land, water, and air, and with too little consideration for the rights of others. A mining company is in business to make a profit, but every company, regardless of the nature of its business, has moral obligations to reduce its undesirable effects on the environment and to safeguard the rights of others. The problem of environmental degradation caused by surface mining is widespread and serious. Minerals in some form occur in each of the 50 States and several States are extensively mined. Data on the acreage disturbed in the United States, by commodity and State are presented in Table 1. Thirty-one States have laws regulating surface mining, (Table 2). Briefly reviewed in Appendix A-1 are the basic provisions of State laws governing surface mining. It can be seen that these laws vary considerably from State to State owing largely to the mining conditions within that State. Of the 24 coal-producing States, only three (Alaska, Arizona, and Utah) do not regulate strip mining. Even the states that are often cited as models of comprehensive regulations still have problems minimizing environmental damages. Uncontrolled surface mining presents a situation as critical to the well-being of the society as any it has ever faced. Many mining activities have imposed huge social costs on the public at large. These costs are long-range and are in the form of stream pollution, floods, landslides, loss of fish and wildlife habitats, unreclaimed land, erosion, and the impairment of natural beauty. In a 1965 Department of Interior study,(1)it was estimated that of the 25,000 miles (1+0,225 kilometers) of contour bench in Appalachia, approximately 1,700 miles (2735 kilometers) are affected by massive landslides. Additionally, 1+800 miles (7723 kilometers) of streams and 29,000 surface acres (11,716 hectares) of impoundments and reservoirs have been seriously affected by coal strip mining operations in the United States.

Jan 1, 1974