Search Documents

By A. L. Engel

High extractions of lead, gold, and silver resulted from treatment of an oxidized, arsenical refractory ore by chloride volatilization. The ore was roasted in an oxidizing atmosphere at 1,000° C. for 1 hour. The chloridizing reagent was 300 pounds of CaC12?2H20 per ton of ore. Ninety-nine percent of the lead, 98 percent of the gold, and 96 percent of the silver, and only 6 percent of the arsenic, were volatilized. These results indicated that a satisfactory method could be developed for treating this type of ore. Recovery and separation of the volatilized values and developing metallurgical and operating data for this process require further investigation on a more extensive scale. Tests by gravity concentration, flotation, and cyanide leaching did not give satisfactory results.

Jan 1, 1958

"The main objective of this research is to identify the mechanisms of control of respirable dust generation in coal mines. Full understanding of the mechanics of crack propagation in coal is of fundamental importance in studies of the generation and control of respirable dust.The main objectives of this fracture investigation are: 1) to determine reliable data on the fracture toughness of coal as a parameter controlling unstable crack propagation; 2) to determine fracture propagation velocity in coal providing data on the terminal velocity at which crack bifurcation occurs and fine fragments of coal material are generated; and 3) to apply the critical strain energy density criterion to model mixed mode crack propagation in coal.The development of the protocol, laboratory procedure and equipment necessary to conduct an extensive mixed mode fracture toughness testing program has been completed. About 80 mixed mode fracture toughness tests, 10 good fracture velocity records and over 50 fracture surface examination with the SME are available. The details of the mixed mode fracture toughness testing are available in a paper titled, ""Development of Mixed Mode Testing System for Geologic Materials"" which is available from the center. The average fracture toughness and critical strain energy density values for the three seams investigated to date are included in the attached Figures 71, 72, 73."

Nov 1, 1988

By Wilber Duvall, Leonard Obert

"INTRODUCTION This report is the first of four to be presented on the microseismic method 4/ of predicting rock failure in underground mining. The application of the microseismic method to one specific case, namely, that of predicting rock bursts in deep mining, has been described in two previous reports. 5/ 6/ Since the publication of these reports 5/ 6/ the method has been extended to other fields of mining, end it is the purpose of this report (Part I) to describe the general microseismic method, giving the empirical facts upon it is based, the different testing procedures, the method of recording and analzing the data, and the interpretations that can be obtained there-from. Part II will describe a series of laboratory experiments that were performed to give information on the origin of microceismims and the microseismic properties of various rocks. Part III will cover application of the method to specific mining problems together with a brief description of a number of investigations performed during, the last three years. Part IV will describe in detail the microseicmic equipment used in the various phases of these investigations."

Feb 1, 1945

By John Taber, Robert D. O'Brien

"INTRODUCTION The Bozeman corundum deposit was first examined in May 1944 by an engineer of the Bureau of Mines. In August 1944, the property was re-examined because of a sharply increased war demand for corundum. A small program of trench exploring was undertaken after the second examination. The work was started in October 1944 and was completed in December 1944. This report presents the essential data obtained by the exploratory work.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that, they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The field work on the Bear Trap project was supervised by E. W. Newman, district engineer Montana District office. The microscopic examinations and. the grid grain-count analyses of the samples and the beneficiation tests were made at the Bureau's laboratory at Salt Lake City, Utah, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

May 1, 1947

By M. H. Stanczyk, I. L. Feld

Dewatering of typical Florida phosphate rock slime by electro - osmotic techniques was investigated to determine if a compacted , plastic solid product could be obtained with simultaneous recovery of the water for re - use . Tests with porous cathodes and rod - type anodes imbedded in dilute slime charges of up to 4 tons in weight showed that the slime could be dewatered to about 35 percent solids . The dewatered products had the consistency of modeling clay . In the large - scale tests using 2.5 - foot electrode spacings , about 21 kilowatthours of power were consumed per ton of water removed in thickening the slime from 17 to 25 percent solids , but the rate of water removal was so slow that the process was not considered commercially feasible . Other tests made with electrode spacings of from 2.5 to 8 feet showed that more rapid dewatering could be obtained but that the power required was excessive . However , for special uses such as stabilizing slime pond dikes where the cost of dewatering might not be a prime requisite , high voltages could be used to rapidly remove the water . Tests of 400 - pound slime charges using a combination of electroosmosis and vacuum filtration showed that the rate of dewatering could be expedited . The average power required to thicken a ton of slime from 15 to 35 percent solids was 5 and 50 kilowatt - hours when operating the electroosmotic filtration cell at potentials of 20 and 100 volts , respectively . calculated filtration area of about 10 square feet per ton of slime treated per day was required to thicken the slime from 15 to 35 percent solids .

Jan 1, 1964

Until man was able to produce light, his working day was pretty much limited to daylight hours. Underground miners have a special problem because in a mine it is just as dark during daytime as it is at night. The first devices used for mine lighting were torches and open flame 011 lamps. Torches made from twisted grass and dipped in tallow or pine pitch would burn for a while, but they made a lot of smoke and probably went out when they were needed most. During the 15001s, miners lamps consisted of a small metal dish with a hook attached to hang it up. The saucer-shaped dish was filled with animal or fish oil and a wick made of twisted fibers was laid In the 011 and hung over one edge where it would burn. This lamp would burn longer than a torch, but the amount of light cast by the pale, flickering flame was probably only a little better than no light at all.

Jan 1, 1976

By Thomas Fraser, J. D. Davis

"INTRODUCTION Preliminary tests of the Oyon coal constituted part of a wartime exploratory and development program in which many agencies participated. The general objective was to find new and adequate source of fuel and other raw materials for greatly expanded industry.The Oyon coal field, known for at least a hundred years to the mining people of Peru, offers a possible source of high-grade process fuel for the growing metallurgical industries of South America and the Pacific coast. Santolalla 4/ reports that low-volatile coal from this region was used in local smelting operations as early as 1850. It has been mined in very small quanti¬ties for many years and used in neighboring mining camps and villages. Small quantities are regularly used at Oroya for the manufacture of carbide, and in recent years small-scale coking operations in specially designed ovens in the region have demonstrated that these coals will make dense coke.During this long period of desultory operations many small openings have been made scattered over a wide area in this general region, indicating very extensive occurrence of the coal measures, although systematic exploration work has not been undertaken. However, current development work of the Banco Minero del Peru has opened up several substantially parallel highly inclined or vertical beds of workable thickness and has followed these deposits to sufficient lateral extent to prove fairly well the existence of substantial reserves on this property."

Mar 1, 1948

By J. C. Edwards

To have the capability to predict the development of localized spontaneous heating within a porous coalbed that is subjected to forced air ventilation or in an otherwise quiescent environment in which buoyancy develops, the Bureau of Mines developed three time-dependent mathematical models, which were used to calculate the temperature increase associated with chemisorption of oxygen by the coal. In each model, spontaneous heating is driven by an Arrhenius first-order reaction between the oxygen and coal. Two models are two-dimensional, and one is one-dimensional. In the first two-dimensional model, a constant-velocity forced convection airflow is specified; and in the other, buoyant flow is allowed to develop in the absence of forced convection. The third model evaluates the airflow from Darcy's law and a specification of the pressure at the surface of a one-dimensional porous coalbed. Numerical computations demonstrated how each model could be used to predict the onset of spontaneous heating when the porous coalbed was subjected to constraints of an imposed internal heat source or a high temperature airflow. The effects of particle size and coalbed compaction upon spontaneous heating were examined with the third model.

Jan 1, 1990

By Jack R. Woodyard

Bonding angles, promotion energies, and relative atomic sizes can be estimated through the solution of a set of algebraic equations generated from simple atomic models, and quantum mechanical parameters such as bond strength can be estimated from simple, hydrogenic form-wave functions. The precepts of The Engel-Brewer Theory are melded with the "Crystal Approximation Model" to produce atomic-structure models making these predictions, The two-valence-electron case is presented in this report. For the candidate atoms Be, Mg, Ca, Sr, and Ba the calculated promotion energies agreed within a few percent of their experimental values. These atomic parameters determine the possible crystal structure of the candidate atoms when alloyed. This is part of the effort at the U.S. Bureau of Mines to develop methods for alloy design in response to requirements for new high-performance alloys that conserve critical or rare materials.

Jan 1, 2010

By Thomas C. Mowatt

Preliminary Bureau of Mines studies of mafic igneous rocks collected from the Rabbit Creek area, northwestern Alaska, indicated concentrations of platinum (412 to 1,406 ppb) and palladium (343 to 892 ppb) in five of eight samples analyzed. The samples represent boulders and cobbles of mafic/ultramafic rocks from this locality. They are not from outcrop. Petrologically, (on the hand specimen scale) the samples are crudely to well-layered and are troctolitic ± gabbroie in character, with primary igneous mafic minerals strongly altered. Small patches of interstitial sulfide minerals, including chalcopyrite, bornite, pyrrhotite, pyrite, and covellite are associated with these altered zones and elsewhere through the specimens. Copper values ranged from 0.1 to 0.3 pct in samples analyzed semiquantitatively; nickel, cobalt, and chromium contents are low. Chemical, mine alogic, and petrographic relationships suggest that the rocks of similar character outcropping in northwestern Alaska could also be considered as prospective for- concentrations or platinum, palladium, and copper.

Jan 1, 2011

By C. G. Kirkpatrick

Analysis of the data produced by a wide-band, sensitive, horizontal, biaxial motion sensor has revealed several distinctive patterns before, during, and after a roof fall. The signals prior to the roof fall are similar in spectra, but one thousand times larger in amplitude, than those after the roof fall. Immediately preceding the roof fall, by two to twelve hours, five events occurred which were larger in amplitude and lower in frequency than even the large pre-roof fall background signals. An interpretation of these events is offered.

Jan 1, 1979

By L. B. Pankratz

Enthalpies were determined for synthetic chalcopyrite (CuFeS2) between 298° and 1,050° K and for synthetic bornite (Cu5FeS4) between 298° and 1,100° K by copper-block drop calorimetry. Two transitions were found for each compound. The lower transitions were both crystal transformations from tetragonal (low-temperature form) to cubic (high-temperature form). The chalcopyrite transformation occurred at 830' K with a heat of transformation of 2,405 cal/mole; the bornite transformation was at 485° K with a heat of 1,430 cal/mole. The other transitions were of the second order and were presumed to be magnetic in character. The second-order transitions for chalcopyrite occurred at 930° K, and the one for bornite at 540° K. Enthalpy increments, entropy increments, and heat capacities are tabulated at even temperatures above 298.15° K. Equations of enthalpy are also given.

Jan 1, 1970

By R. R. Wells, W. W. Agey

"INTRODUCTION Oxide manganese ore from the Sheep Mountain property was of intermediate grade (23.0 percent manganese) and contained silica as the major impurity. The deposit from which the ore was taken is known as the Sheep Mountain manganese property and is 8 miles west of Durkee, Oreg. Test work was done in the metallurgical laboratories of the Bureau of Mines at Salt Lake City, Utah, on representative samples cut from a 290-pound shipment of crushed ore submitted by the Oregon State Department of Geology and Mineral Industries and reported to be typical of the Sheep Mountain deposit.ACKNOWLEDGMENTSThe authors wish to acknowledge the assistance of R. S. Doan, former assistant director of the Bureau of Mines, under whose supervision the manganese program was initiated in 1940, and, the valuable suggestions made to them by S. R. Zimmerley, now chief, Salt Lake City Division, Metallurgical Branch. Acknowledgment also is made to H. G. Poole and C. H. Schack for their suggestions and contributions to the organization and prosecution of the work of the Ore Dressing Section. Microscopic work on the ores and many ore-dressing products was done by L. G. Evans -and the late. B. E. Head. Our appreciation is extended also to H. E. Peterson, chief chemist, and members of the analytical staff for the many analyses made of the ores and ore-dressing products."

Nov 1, 1947

Provide reasonably priced, reliable fire protection for front-end loaders. Approach Automatic fire sensing and suppression systems were developed and ruggedized for use on front-end loaders operating in harsh mine environments. How It Works Temperature sensors mounted in the loader's engine, transmission, and articulation areas detect the heat from a fire while it is still small and controllable. This triggers the release of the ABC class dry chemical extinguishing agent through a fixed piping system onto the fire. The system can also be manually activated from either the cab or ground level. Locations of the principal components of the system are shown in the drawing. Two control subsystems were designed to respond to varying fire protection needs and mine conditions. One subsystem only initiates discharge of the extinguishing agent. The other subsystem initiates visual and audible operator alarms if there is a fire sensed or if there is a fault in the control circuit.

Jan 1, 1979

By Carl F. Wingquist

Electrical resistance heating to effect thermal fragmentation of semiconductive rock was examined by the Bureau of Mines. Tests were carried out on copper-bearing ores of the Nonesuch Shale Formation in the laboratory and in the the field at White Pine, Mich. Fieldwork included primary and secondary breakage tests. Heating tests on in situ rock failed to produce thermal dam-age to an extent considered useful; however, boulders up to 30 ft3 were effectively broken by the method. Power input to the test rock was taken from a 50-kV, 5-amp dc power supply.

Jan 1, 1976

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960

By A. W. Fahrenwald

The logic leading to the development of the experiments in this paper already has been stated in Part I,3 but is briefly as follows: The results of the batch-grind experiments in which time of "grind" and fineness of finished product were the variables, strongly indicated (1) that batch grinding involving a single grind could not be operated under any condition to give maximum mill efficiency, (2) that the, sieve analysis of the feed charge in the mill materially affected the efficiency of the mill, and (3) that the percentage of finished product in the mill is a vital factor in ball-mill efficiency. A laboratory closed-circuit grind technic designed to simulate present closed-circuit grinding suggested itself, in which: a ball mill and a classifier constitute the grinding unit. The features of the closed-circuit grinding system are: (1) Short large diameter mills, (3) rapid flow of pulp through the mill, (3) continuous automatic removal of finished product from the system, and (4) high circulating loads. The high circulating load is a result if the short length of the Mill - that is, of the time the charge remains in the mill - and the small percentage of finished material produced during each circuit of the feed through the mill.

Jan 1, 1930

"The following articles were produced through funding under Generic Mineral Technology Center for Respirable Dust research. Full articles appear in the proceedings, 3rd Symposium in the Mineral Industries, published in 1991 by the Society for Mining, Metallurgy and Exploration, Inc.Personal Diesel Exhaust Aerosol SamplerV.A. Marple, K.L. Rubow, and Y. TaoParticle Technology, Mechanical Engineering Department, University of Minnesota, Minneapolis, Minnesota(Section ill. Diesel I: Diesel Particulate Measurement, pp. 73-81)Abstract. Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective 18Dlpling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler.Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8 µm while mineral dust is greater than 0.8 µm.One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the nonrespirable particles while the inertial impactor state, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles ( <0.8 µ.m and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol."

Mar 1, 1992

By Frank J. Wiebelt

Work on the Abbott-quicksilver property was part of the general program of th~ Bureau of Mines in its investigation of domestic mineral resources, which are essential to national defense or industry and of which our present or probable future supplies are inadequate. The mine was discovered in 1862, and the intermittent production up to 1947 has totaled around 37,500 flasks of quicksilver. Output has come from ore shoots formed in the vicinity of fault intersections in a narrow zone composed of lenses of silicified serpentine breccia interbedded with shale. Work by the Bureau included the drilling of six diamond-drill holes aggregating 2,845 feet. Several possible ore zones were intersected by the drill holes. Field work was begun in April 1948 and concluded in October of the same year. This report gives detailed results of the diamond drilling and a brief account of the history and description of the ore deposits.

Jan 1, 1949

By H. J. Heinen

Malononitrile [CH2(CN)2J, which forms a carbanion in basic solutions, was investigated as a potential leachant for gold and was shown to be an effective extractant in alkaline pulps. Malononitrile was comparable to equal molar quantities of sodium cyanide (NaCN) in leaching gold from an oxide ore and yielded 10 to 20 percent higher recovery in leaching a refractory carbonaceous ore, although dissolution was slower with malononitrile than with cyanide. Complete recovery of the gold from the pregnant solutions was achieved by coprecipitation with a lead salt on zinc dust; the leachant was shown to be capable of regeneration and recycling a limited number of times. Addition of an anion-exchange resin to the carbonaceous pulp containing malononitri1e increased gold recovery from 67 to 95 percent. Some malononitrile derivatives were also shown to be gold solvents.

Jan 1, 1970