Search Documents

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By Thomas J. Peters

The Danskin/South Fork Boise River study area is 40 air km southeast of Boise, Idaho. The 16,000-hectare, two-segment area is mainly underlain by Cretaceous-age granodiorite and an aplitic and pegmatitic complex of the Idaho batholith, Miocene-age rhyolitic tuffs and lavas, and late Tertiary-age basalt flows. No mineral resources were identified in the study area. One mine, The Flat Creek mine, which produced several ounces of gold and silver, was found in the study area. It is geologically similar to deposits in the Neal mining district, adjacent to the northwest corner of the area; gold mineralization occurs along east-northeast-trending faults and associated quartz veins, which dip moderately to steeply southeast, and within adjacent Cretaceous granitic rock. Samples indicate the Flat Creek deposit is not rich enough to mine underground, and near surface, open-pit-mineable deposit areas could not be identified. However, exploration is warranted there and also in the 7-km interval to mines in the Neal district, and for extensions of those mines. No evidence of geothermal activity was observed, although there are hot springs in the vicinity. Some alluvial (placer) samples from the interior of the study area contained free gold, but no substantial gravel deposits were seen.

Jan 1, 1993

By Oliver Bowles

A conviction is growing that depressions and other adverse conditions are not entirely unavoidable if a knowledge of past achievements and shortcomings is intelligently, applied in shaping the course of industry. Mineral producers have available a source of such knowledge concerning; their industry in the statistical records of the United States Bureau of Mines, and by scanning, this increasingly exact history can obtain information on which to found a more stable future. This paper contains a brief history, covering more than 50 years, of the activities of the nonmetallic mineral industries as a group, followed by short histories of each of the more important commodities in which are noted the circumstances that lave influenced their development.

Jan 1, 1933

By J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 2010

By R. E. Cerullo

Many computer programs have been written which are capable of performing a least squares fit, both linear and nonlinear, to data gathered by the petroleum researcher. However, when the petroleum engineer tries to program methods of analysis he has used manually in the past, such as forecasting production by decline-curve analysis, more than a knowledge of the use of existing least squares programs becomes necessary. It is the intent of the authors to report the techniques used in the development of such a decline-curve program.

Jan 1, 1970

By Thomas A. Jones

An impure variety of barite, which lends itself well to the manufacture of heavy drilling mud for oil wells, is widely distributed throughout the Ouachita Mountains in Arkansas. The ore mined in the area and used for drilling muds usually contains an average of 67 percent barium sulfate, although ores as low as 50 percent BaSO4 are occasionally used. Due to the increased demand for barite for drilling caused by the intense search for hew oil occurrences during the years 1945 and 1946, the Federal Bureau of Mines began an investigation of barite deposits in the Ouachita? Mountains in October 1946. In all, 10 barite deposits were examined, trenched, sampled, and studied during the investigation, which was terminated in May 1947.

Jan 1, 1948

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By Joseph E. Matta

The Bureau of Mines conducted a field study to investigate thin suppression of respirable dust by water sprays on a continuous-mining machine. Determining the importance of the top and bottom sprays for two types of spray nozzles was emphasized. Results showed, at a 90-pct confidence level, that (1) at least 70 pct of the dust was generated during the sump cut, even though nearly half of the coal was mined during the downshear operation, (2) the water sprays on the top of the boom had little effect in suppressing respirable dust, and (3) B.D. 5 spray nozzles mounted beneath the boom reduced dust at least 33 pet more than B.D. 5 sprays mounted on top of the boom. A single-cut technique was developed that gave good reproducibility for replicate cuts (coefficient of variation of 20 pct).

Jan 1, 1976

By Robert H. Ridgway

Scrap iron and steel attracted attention during 1937 because of the unprecedented exports and the concomitant agitation in some quarters to prohibit the exportation of this essential raw material except on license by the President. This report does not attempt to analyze the statistics given in the light of the controversy over the limitation of scrap exports, but it is believed that students of this problem will find many essential basic data in the various tables presented herein. This paper presents the results of the third in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States. The study was inaugurated in 1935 by the Bureau of Mines in response to requests from trade organizations and others for detailed

Jan 1, 1938

By Robert H. Ridgway

Scrap iron and steel attracted attention during 1937 because of the unprecedented exports and the concomitant agitation in some quarters to prohibit the exportation of this essential raw material except on license by the President. This report does not attempt to analyze the statistics given in the light of the controversy over the limitation of scrap exports, but it is believed that students of this problem will find many essential basic data in the various tables presented herein. This paper presents the results of the third in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States. The study was inaugurated in 1935 by the Bureau of Mines in response to requests from trade organizations and others for detailed

Jan 1, 1938

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By A. R. Rule

Laboratory tests were conducted to study removal of magnesium impurities from western phosphate rock concentrates by selective leaching. The systems evaluated included leaching with dilute sulfuric acid, with ammonium sulfate, and in an aqueous medium with sulfur dioxide gas. Set standards for the magnesium impurity level of phosphate rock concentrates are not available, but industrial practice has indicated that magnesium in excess of 0.3 percent MgO causes problems in phosphoric acid manufacture. Removal of magnesium was accomplished with all three systems. With dilute H2S04 the magnesium level was reduced to less than 0.1 percent MgO with an accompanying P205 loss of 6 percent. Magnesium oxide levels from 0.3 to 0.2 percent were obtainable with ammonium sulfate. However, the system requires concentrate roasting at temperatures of 900° C or higher, heated pulps (100° C), and large quantities of ammonium sulfate. Selective leaching was obtained using S02 gas in an aqueous concentrate slurry. Magnesium oxide content was reduced to less than 0.1 percent without loss of phosphate.

Jan 1, 1970

By Paul Zinner

An exhaustive program of geologic studies and mapping has been conducted by the Geological Survey in the Iron River district of Michigan since May 1943. Means of contributing to the success of these studies were sought by the Bureau of Mines, and eventually a program involving geophysical studies and core-drilling was undertaken in the area. All of the work was done either to develop data that would contribute directly to geologic studies or to investigate geophysical methods that might be used as a primary means for the discovery of minable iron ore.

Jan 1, 1949

By William J. Campbell

These investigations were undertaken as part of a program to determine the optimum X-ray spectral lines to use for analyzing the wide variety of samples received by the X-ray Laboratory. Theoretical calculations and experimental data derived from these investigations show that longer wavelength spectral lines, > 2A, are very useful for many analytical problems. Because of the low fluorescence yield of the elements of atomic numbers 13-22 and the small depth of penetration of their X-ray spectral lines, these elements were originally considered to be insensitive; however, these studies show that the wide dispersion of their spectral lines, coupled with their weak beta lines, permits the use of wide collimation, thus increasing the line intensity. More importantly, the background due to scattered primary radiation is very low in the long-wavelength region.

Jan 1, 1959

By Gilbert M. Farrior

The electrical resistivity the coefficient of electrical resistivity the Hall coefficient, and the absolute thermoelectric power were determined in this Bureau of Mines investigation for nine compositions of the TiB2-CrB2 sub-system. The numerical values of the electrical resistivity and the thermo-electric power were greater for the intermediate compositions than for the end members. The absolute values of the Hall coefficients and the coefficients of electrical resistivity were less for the intermediate compositions than for the end members. The electrical resistivities and Hall coefficients were about the order of magnitude of most metals--from 34 to 202 microhm-cm and from about 0 to -23.3 X 10-4 cuP/coulomb. The thermoelectric power was somewhat greater than that of most metals--up to 15.6 microvolts per 0 C.

Jan 1, 1965

By G. V. Sullivan

This report summarizes the results of a preliminary study concerning manganese extraction from low-grade dolomitic materials from the Philipsburg district in Montana by the Dean-Leute ammonium carbamate process. Studies were made to determine the relationship between the variables involved in treating these materials by a roast-leach process and the amount of manganese extracted. The variables studied were the roast temperature, the roast particle size, the molar ratio of NH3 to CO2 in the leach solution, the liquid-solid ratio in leaching, the leach time, and the size of the particles being leached. The roast-leach studies were statistically designed, and the experimental results were evaluated by an analysis of variance.

Jan 1, 1962

By Milton Orchin

There has been a good deal of speculation as to the function of a vehicle in the coal hydrogenation process. One of the most fruitful theories has been the suggestion that a vehicle such as tetralin functions by supplying hydrogen to the coal, and that the high-pressure hydrogen present in the system serves to regenerate the tetralin. In order to obtain experimental evidence bearing on this theory, a series of experiments was planned in which varying quantities of tetralin were used with coal in the presence of high-pressure hydrogen. This paper reports the results of these experiments.

Jan 1, 1949

By L. R. Burdick, R. Wiggers, J. F. Berkley

"INTRODUCTION On February 23, 1944, Solid Fuels Administrator Harold L. Ickes stated that the existing fuel shortage made it necessary to utilize a great surplus of freshly mined anthracite ranging in size from Barley (No. 3 Buckwheat) downward through the smaller sizes. As a part of the program to increase the use of such coal, field trials of mixtures of bituminous slack coal and anthracite Barley were made on industrial-size stokers at many fuel-burning plants. The following covers the test information it was possible to accu-mulate during the work of initiating the use of these mixtures at the plants.SUMMARY AND CONCLUSIONSField tests of various mixtures of bituminous slack coal and anthracite Barley on industrial-type stokers show that the use of such mixtures is very practicable and that it is possible to change and usually to adjust to an improved condition the characteristics of a fuel bed of eastern bituminous slack coal by the addition of proper amounts of anthracite. The improved uniformity of the fuel bed of single-retort stokers makes possible less manual attention to the bed. Air flow through the fuel bed is affected.Smoke is decreased. In general, the fly ash and also the unburned combustible in the fly ash and refuse are increased. Clinkering in the fuel bed is generally lessened. The peak-load carrying capacity of the stoker is definitely affected, usually adversely for the higher percentages of anthracite."

May 1, 1946

By Roy G. Stott, John A. Johnson, Floyd G. Anderson

"This information circular discusses drilling and blasting in open-cut iron-ore mines and is one of a series of papers describing iron-ore mining practices in the Lake Superior district to aid in preventing accidents in that industry.The Lake Superior district consists of the Marquette and Menominee ranges of Michigan, the Gogebic range of Michigan and Wisconsin, and the Vermilion, Mesabi, and Cuyuna range of Minnesota. Open-cut mines produce 8o percent of the iron ore mined in the district; 98 percent of the total Lake Superior district open-cut ore is produced in Minnesota and 2 percent in Michigan. The entire Wisconsin iron-ore production is from underground nines. The Mesabi range in Minnesota produced 93 percent of the open-cut iron ore and 76 percent of the total iron ore in the district in 1947.During the 8-year period 1940-47, 619,000,000 gross tons of iron ore were shipped from mines of the district, or 85 percent of the United States output. Approximately 78,000,000 gross tons of iron ore were shipped from the mines of Minnesota, Michigan, and Wisconsin in 1947.This paper is based primarily on observations daring the period July 1947 to March 1948. Thirty-two open-cut mines were visited; 28 on the Mesabi range, 3 on the Cuyuna range, and 1 on the Marquette range. In 1947, 36,100,000 tons of iron ore was shipped from these 32 mines, or 59 percent of the open-cut ore and 46 percent of the total iron ore shipped from the district. During 1947 about 90 open-cut iron-ore mines were operating in the district, and the annual production of each ranged from 25,000 to 10,000,000 tons.Many recommendations included in this paper for improving safety and preventing injuries to employees were taken from Bureau of Mines Information Circular 7387.Data were collected under the direction of Frank E. Cash, former supervising engineer, Health and Safety Division, Bureau of Nines, Duluth, Minnesota. E. W. Felegy, mining engineer, Safety Branch, gave valuable assistance in reviewing and editing the manuscript.The authors gratefully acknowledge the information and assistance given and the numerous courtesies extended to them by officials of the following mining companies:All the Lake Superior iron ores occur in bedded formations that range from less than 100 feet to over 2,000 feet in thickness. These formations are designated by one commonly applied name, ""iron formations.""4/The Mesabi range in northern Minnesota, about 70 miles northwest of Duluth, was opened to mining in 1892; it is the largest single source of iron ore in the United States. It is 75 miles long and, because of the gentle dip of the ore formation, it ranges in width from 1-1/2 to 3 miles.5/ The ore formation, which is nearly horizontal, has a maximum thickness of about 450 feet and is covered by a glacial drift that ranges from 10 to over 100 feet in thickness. Most of the ore is near the surface and adaptable to open-cut mining."

Mar 1, 1950

Safe operation and system integrity are two important properties of a mine hoist electrical system. Previous methods used to assess these systems, though rare, have involved extensive downtime and required skilled personnel. The recommended design considerations presented in this report are for a proposed automated system that will perform real time measurements, calculations, and recordings of pertinent performance data. Included are equipment installation and test procedures to be used with the system. The report also contains descriptions of the hoist performance criteria, and how they are to be collected.

Jan 1, 1985