Search Documents

By Alan G. Mayton

Exposure to whole-body vibration (WBV) and the postural requirements of the job have been identified as important risk factors in the development of musculoskeletal disorders of the back among workers exposed to a vibratory environment. This paper focuses on preliminary results of WBV data collected for two groups of haulage trucks ? four older trucks from manufacturer A (MFR-A) and two newer trucks from manufacturer B (MFR-B). All of the trucks and their respective seats were considered to be in good working order during the study. Measurement periods for the truck groups had similarities, but varied from 2 to 58 minutes. Sampling times for the older trucks included a mean of 19.5 minutes and a standard deviation (STD) of 6.5 minutes compared to a mean of 40.8 minutes and a STD of 12.1 minutes for the newer trucks. Data collection coincided with the approximate delivery and first operation of the new trucks, and occurred approximately 12 months apart under similar weather and road conditions, and with the same drivers except an additional driver was included with the older trucks. Truck routes were somewhat different in that quarry production had changed location in the time between data collection activities. Overall, the results suggest that the newer trucks may provide better overall isolation to drivers/operators from WBV exposure compared to the older trucks operating at the quarry; although, this will need to be confirmed with additional measurements. Considering the higher variability and shorter sampling times for the older trucks, the results should be viewed with caution. For two of seven trials, the older trucks showed that seats amplified vibration, i.e., a transmissibility (T) >1.0. Seat T for the older trucks ranged from 0.31 to 1.17 with a mean of 0.77 and STD of 0.32. This contrasted with the newer haulage trucks where seats amplified vibration in 3 of 8 trials. In this case, T did not vary greatly and ranged from 0.87 to 1.05 with a mean of 0.97 and STD of 0.07. Regarding older trucks, in five of seven trials, the seat (output) data of weighted root-mean square (RMS) acceleration (wRMSZ) for the dominant z-axis exceeded the action level of 0.5 m/s2 action level recommended by the European Union Good Practice Guide for WBV (EUGPG) and levels exceeded the recommended exposure limit of 1.15 m/s2 in two of the seven trials. The wRMSZ values for the older trucks varied from 0.41 to 1.83 m/s2 with a mean of 0.99 and STD of 0.57. Similarly, newer trucks indicated a narrower range of wRMSZ from 0.38 to 0.95 m/s2. The mean wRMSZ was lower for the newer trucks at 0.58 m/s2 with a STD of 0.23 m/s2. Similarly, newer trucks indicated wRMSZ reached or exceeded the action level in four of eight trials. None of the trials with the new trucks showed wRMSZ levels that reached or exceeded the recommended 1.15 m/s2 exposure limit. As an indicator of driver/operator discomfort, overall weighted total RMS acceleration (vector sum) values seem to show a ?rougher? ride for the older trucks. The vector sum values for these trucks ranged widely from 0.70 to 2.59 m/s2 and, in four of seven trials, showed levels greater than 1.40 m/s2. The mean vector sum was 1.44 m/s2 with a STD of 0.75 m/s2. Comparatively, the newer trucks exhibited less variation with a range from 0.69 to 1.59 m/s2. The mean vector sum was 1.02 m/s2 with a STD of 0.35 m/s2. Vibration dose values for the dominant z-axis (VDVZ), gave a sense of vehicle jarring/jolting conditions. All trials with the older trucks were within the recommended EUGPG action level of 9.1 m/s1.75. On the other hand, in three of eight trials, both newer trucks exceeded this action level with values of 9.18, 12.58, and 13.21 m/s1.75. Neither truck group showed VDVZ that exceeded the exposure limit of 21 m/s1.75. A statistical analysis was not conducted, since the differences reported between truck groups may not be statistically significant owing to the relatively small sample size. Road conditions, changes in the truck routes, and driver/operator differences (e.g., stopping and turning) are possible factors in the higher VDV for the newer trucks.

Jan 1, 2008

By E. S. Leaver

Experiments dealing with the dissolution of silver by cyanide from various silver minerals-were reported, several years ago.4/ This work showed that the silver in some silver minerals is completely and readily soluble in cyanide solution, whereas other silver minerals must be given special treatment before or during cyanidation to obtain much dissolution of the silver by cyanide. Flotation as a method for treating silver ores has not been studied much, except in the case of base-metal ores carrying silver, Particularly lead-silver ores. However, many mills now are concentrating gold ores by flotation, and when such ores also contain silver the recovery of the silver by flotation is of considerable importance. Moreover, many mines contain ore in which silver is the principal valuable constituent. Some of these ores are amenable to cyanidation, but the cost of a cyanide plant may be prohibitive because of limited ore bodies or other factors. In such instances the successful application of flotation would mean that the property could be operated.

Jan 1, 1939

By H. R. Appell

The Bureau of Mines studied the conversion of a variety of cellulosic wastes, for example, sawdust, bovine manure, sewage sludge, urban refuse (free of metal and ceramics), etc., to heavy oils. The objective of the investigation was to determine the scope of the reaction and elucidate the chemistry involved. The reactions took place in the presence of synthesis gas and water or carbon monoxide and water under conditions of elevated temperatures and pressures. Waste conversions above 90 pct, often near 99 pct, with oil yields in the range of 40 to 60 pct, were obtained in the temperature range of 250° to 425° C and pressure range of 1,500 to 4,000 psig. Because mild conditions were sought, most of the experiments were conducted at temperatures of 250° to 350° C and pressures of 1,500 to 3,000 psig. In general, lower viscosity products were obtained at higher reaction temperatures. Conversions and oil yields were significantly increased by operating in the presence of a high-boiling oil; either anthracene oil or oil recycled from the process was satisfactory. Synthesis gas containing 50 pct carbon monoxide gave satisfactory results as a replacement for carbon monoxide. Cobalt molybdate on alumina catalyst, used with sodium carbonate, gave a product of lower viscosity and lower oxygen content than sodium carbonate used as the sole catalyst. The waste-to-oil process has been successfully investigated in continuous flow equipment as well as in batch autoclaves.

Jan 1, 1975

By J. E. Berg

This paper3 describing the mining methods at the Page mine operated by the Federal Mining & Smelting Co., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Page mine is the most westerly of the producing lead-silver-zinc mines in the Coeur d'Alene mining district of Idaho, being situated 5 miles west of the city of Kellogg and at an elevation of 2,677 feet above sea level. It may be classed as one of the new active producers, of the district and owes its present activity largely to the development of floatation.

Jan 1, 1930

By Jennifer S. Riefenberg

The U.S. Bureau of Mines conducts basic and applied research related to predicting, eliminating, and/or controlling rock bursts in underground hard-rock mines and coal bumps in underground coal mines. An important element in this research is the development of a reliable and efficient microseismic source location technique. This report presents the results of a Bureau study to develop and evaluate a new algorithm to locate microseismic events based on the Simplex method, a powerful linear programming technique. The technique was tested on both field data and simulated data. Microseismic event source locations obtained with this new Simplex-based algorithm were shown to have less error than those locations obtained using a least squares method. It was concluded that the Simplex approach to source location of microseismic events can be used effectively in microseismic monitoring.

Jan 1, 1989

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

By M. R. Geer

The Bureau of Mines surveyed the solid wastes that have accumulated from coal mining in Washington, Oregon, and Montana. Location, amount, character, and condition were determined, and both economic and environmental factors were considered. Areas covered by waste comprise 800 acres in Washington, 5 acres in Oregon, and 1,200 acres in Montana. In a few cases waste is being utilized, particularly cinder from burned refuse dumps, as fill in road construction and as a ceramic raw material. It is estimated that wastes deriving from coal mined for electric power generation by 1974 may amount to 3 million tons of washery refuse, 2.7 million tons of fly ash, and 1,000 acres of spoil banks.

Jan 1, 1969

By Joseph A. DeCarlo

The annual survey of the oven-coke industry by the Bureau of Mines, United States Department of the Interior, described in this report shows that 79 plants were operating in 22 States December 31, 1956. On that date 15,923 serviceable ovens existed, with a maximum total annual coke capacity of 79,965,100 net tons, and 631 new ovens were under construction. Their annual coke capacity was 3,307,300 net tons. The number of serviceable ovens in existence relates only to those capable of producing coke and does not include (1) any ovens that were blanked off or retired permanently in batteries that were operating December 31, 1956, and (2) ovens that had been demolished and were being rebuilt on that date. For this reason, the number of ovens at furnace plants reported by the Bureau of Mines at the end of each calendar year differs from the number reported for the same group by the American Iron & Steel Institute, as the institute includes ovens being rebuilt.

Jan 1, 1958

By C. J. Chindgren

Upgrading of commercial red cake and recovery of vanadium oxide from uranium-vanadium mill solutions were investigated by the Bureau of Mines. Alternative procedures potentially useful for manufacture of high-quality vanadium oxide at the mill site were explored and developed. The simplest and best procedure for converting commercial red cake containing about 10 percent combined sodium and potassium oxides (Na20) (K20) into a 98- to 99-percent vanadium pentoxide (V205 product appeared to be a metathesis in an ammoniacal solution of ammonium sulfate. Molybdenum, as well as the alkali metal oxides, was removed from the red cake by this procedure at a modest expenditure of labor and reagents. When preparing vanadium oxide of higher grade, it was necessary to dissolve the red cake and reprecipitate the vanadium as ammonium metavanadate. Calcination at 450° C, decomposed the metavanadate and yielded oxide of about 99.5 percent V205. By recyrstallizing the metavanadate before decomposition, an oxide product approaching 99.9-percent purity was obtained.

Jan 1, 1962

By D. Harrington

Along with other phases of mining , the ventilation of metal mines has been affected by the business depression of 1930. As might be expected , some of the results are favorable , and some are distinctly disadvantageous to progress . Probably the worst effect of the recession of mining activity is that , as usual , one of the first departments of almost any industrial establishment ( and this is especially true of mining ) to be curtailed is that which concerns what might be called welfare work , such as safety , health , etc. , and ventilation : in consequence , a number of men who were employed mainly on ventilation work in metal mines are now out of employment and their former duties either are being handled by others as only part of a crowded routine or are being allowed to lapse . On the bright side of the picture is the following paragraph from a letter by the ventilation and sarety engineer of the United Verde Copper Co. , Jerome , Ariz . , indicating that money and effort expended on ventilation during " flush " times give results which aid in money savings when depression comes : The desirability of absolute control over the ventilation system has again been demonstrated at this mine . Under full operation we have been using approximately 500 hp . to drive our big fan . Under curtailed operations we naturally do not require as much air , so by sending the air only where needed and airing out all other places periodically to keep timber , etc. , in good condition we have been able to economize in the quantity of air required . The fan speed has been reduced and the power dropped to 300 hp . , thus effecting a material saving in the power bill , and still maintaining an efficient ventilating system . "

Jul 1, 1931

By R. V. Ramani, S. Shankar

"Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991 ). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken:• a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities;• a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and• the mathematical modeling and computer simulation of the re-entrainment phenomenon.In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies,it was observed that increasing the air velocity increased the rate of re-entrainment ( Shankar and Ramani, I 994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to air flow was negligible compared to the contribution due to walking. IntroductionIn underground coal mines, dust is produced primarily during the process of mining and during such activities as pillar spall, loading, belt transfer and roof fall. The generated dust is entrained and then collects on surfaces through dispersion, diffusion and eventual deposition. Removal forces, such as flowing ventilation air or turbulence caused by walking and moving vehicles, can re-entrain the deposited dust (Hall, 1955). A portion of the re-entrained dust remains airborne and increases the concentration of airborne dust in mine airways.The presence of airborne coal dust in mine airways in large concentrations can be hazardous. Health effects include coal workers' pneumoconiosis (CWP) and silicosis, and it can be a nuisance affecting visibility. In addition, as is common during methane explosions, if the concentration of airborne coal dust becomes significant, there could be a coal-dust explosion (Singer, Cook and Grumer, 1972; Singer, Harris and Grumer, 1974; Edwards and Ford, 1988). Through concerned research efforts over the last decade, significantprogress has been made in reducing the airborne dust concentration in mine atmospheres. However, secondary sources, such as re-entrainment, have not been studied in-depth. It is important to understand the phenomenon of re-entrainment and its potential contribution to the airborne dust concentration in mine airways for further decreasing airborne dust hazards in mines."

Dec 1, 1996

By R. W. Stahl

Coal mining has been revolutionized by the continuous miner. This machine has replaced, or has combined into 1, 3 former operations: Cutting, blasting, and loading. During the 25-year period before this machine was introduced, advances had been made in transportation, but the actual "coal getting" remained virtually the same. As frequently occurs, the multiple-purpose continuous miner introduced a new hazard--more rapid liberation of methane. The coal output formerly obtained from 10 to 20 working places might now be obtained from 1. It is true that circulation of air was generally increased; but the bulk of this machine virtually precludes continuous flow of air across the face, where gas may accumulate. Apprehension about this possible hazard led the Bureau of Mines to test face atmospheres during operation; and Report of Investigations 5288, Methane Buildup During Cutting and Continuous Mining Operations (published in 1956), presents proof that real danger may be present in many otherwise well ventilated mines.

Jan 1, 1958

By A. J. Kraemer

"Introduction In 1925 the Bureau of Mines published as Technical Paper 346 a discussion of typical crude oils of the Western Hemisphere. That paper was one of a series of surveys of typical crude oils, and was the first of these to deal with properties of crude oils from countries other than the United States. The paper contains comments, tabulated data, and individual analyses of crudes typical of the producing districts of Canada, Mexico, Trinidad, Venezuela, Argentina, Colombia, and Peru; for comparison, it also has analyses of typical crudes from the chief producing districts of the United States.The Bureau of Mines undertook a study of foreign crude oils for two reasons: First, foreign fields are potential sources of supply for the United States; in fact, considerable quantities of some foreign crudes have already been imported. Second, these oils are very similar in physical and chemical properties to oils found in the United States, and a study of these resemblances has scientific value.After the publication of Technical Paper 346, the attention of the Bureau was called to the fact that the two analyses of crude oil from Venezuela which appeared in that paper were not completely representative of the production of that country. Samples of other types of oil were procured through the cooperation of Mr. R. Ogarrio, manager of the Texas Petroleum. Co., Huston, Texas, and officials of the following companies operating in Venezuela; British Controlled Oilfields, Ltd., Venezuelan Oil Concessions, Ltd., Creole Syndicate, and Venezuelan Gulf Oil Co.. Samples were collected and dispatched by Mr. D. 3. Park, representative in Maracaibo, Venezuela, of the Texas Petroleum Co. The value of the interest and cooperation of these agencies in obtaining the samples is gratefully acknowledged."

May 1, 1927

By D. S. Kingery

Recent Federal coal-mine inspections have revealed some good and some definitely hazardous practices and systems for transporting; handling, and storing lubricants in and about coal mines. Improper storage or handling of. lubricants in coal mines has caused disastrous mine fires or, by supporting combustion, has made fires from other sources more difficult to fight. Careless handling of grease and oil around electrical equipment wastes much oil and permits entrance of grit and foreign substances into the working parts, which causes excessive wear and increases the possibility, of electrical ignition.

Jan 1, 1943

By R. Clark Lantz, Charles Stanley, David E. Hinton

Morphometric examination of lung alterations following exposure to toxic and pathogenic substances is invaluable in detecting subtle changes which might otherwise be overlooked. Results, from evaluation of initial structural alterations, support and guide subsequent nonmorphological techniques and, when coupled appropriately, can lead to a better understanding of the pathogenesis of a disease. Morphometry is a technique which can be used to determine, quantitatively, the site, extent, development, and progression of a disease state. Determination of the extent of tissue and cellular involvement in the response to inhalation of silica has been performed in order to gain a better understanding of the development of fibrosis following inhalation of this toxicant. In addition, since silica has been postulated as one of the important pathogenic minerals in coal mine dust' it is important to understand the lung tissue response to silica prior to evaluating the effects of inhaled coal mine dusts. Male Syrian golden hamsters were placed in Hazelton 1000 inhalation chambers and were exposed to either filtered air (controls, n = 24) or filtered air plus 30 mg!m3 silica (Min-U-Si110,95%ofparticles < 5 um,n =24)for16hours per day, five days per week, for two weeks. Animals were returned to the animal quarters prior to subsequent tissue processing at 1, 4, and 12 weeks following exposure. This schedule was designed to allow time for the development of fibrosis. Lungs were fixed by intratracheal perfusion of ½ strength Karnovsky's fixative at a pressure of 20 cm H20 and tissues were taken for embedment and analysis at the light level. Determination of site, extent, and development of alterations was performed using a multitiered approach. Changes in large structures (airways, blood vessels) was determined prior to evaluation of changes at the septal tissue level. Data will be presented outlining the progression of changes. Results indicate the usefulness of morphometric analysis of lungs following inhalation of toxic substances in quantitatively defining the structural alterations.

Mar 1, 1989

By G. S. Baur, J. W. Montoya, S. R. Wilson

Beryllium occurs in the Honeycomb Hills area in volcanic tuff similar to the more extensive berylliferous tuff occurring 20 miles east at Spor Mountain , Juab County , Utah . Samples from the two areas have been mineralogically examined to ascertain whether they have similar characteristics . The Honeycomb Hills samples showed the presence of beta- Be ( OH ) 2 , as well as an amorphous berylliferous substance , whereas in the Spor Mountain tuff the beryllium- bearing minerals are hydrated bertrandite and berylliferous saponite .

Jan 1, 1964

By M. C. McCall

When electric current of any appreciable magnitude flows from a power line into the earth, a change sometimes takes place in the conditions of resistivity immediately surrounding the electrode or medium of contact. If the conducting medium is composed of moist earth or clay the effect is to increase rapidly the resistance. If the conducting medium is coal or a coal bed, the effect is one of slowly decreasing resistance as the coal is carbonized, If, however, the flow of current is not enough to carbonize the coal, it will dry slowly, with a resultant increase in resistance. Measuring ground resistance, or impedance, with conventional commercial ground testers does not always indicate the current that will flow in the earth circuit from a direct-current or an alternating-current power circuit. The exact reason for this has not been determined however, it is thought to be due to the comparatively minute currents used for such testing. A typical ground, tester used by the authors for this work indicated a maximum current of 25 milli-amperes. The frequency of this testing current also has an effect on the readings in all probability. While the possibilities of the effects of varying frequencies has by no means been fully explored in this investigation, there are very definite indications that the impedance of a circuit through a section of earth will vary in some inverse relationship to the frequency of the applied voltages. This is evident at ordinary power-line frequencies ns well as at higher frequencies up to 200 kilocycles, which was the highest frequency available for tests in this investigation. This report is written in the hope that it will stimulate further investigation of the possibilities suggested for communication and the development of safety devices for increased electrical safety in coal mining.

Jan 1, 1952

By J. Koster

During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report.6/ The geology of the Marysvale region has been reviewed recently.7/ The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.

Jan 1, 1939

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation&apos;s economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988