Search Documents

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By R. Lusignea

A device has been developed for nondestructive testing the holding power of split tube friction rock supports. It operates by measuring the amount of decrease in internal volume when the support is forced into the drilled hole. The pullout force or slip load is a function of this decrease in volume. The device gives readouts of the average internal diameter and predicted pullout force or the support. Laboratory and field tests showed excellent repeatability and good correlation between predicted and actual pullout force. The device is hand-operated, lightweight (7.5 lb) and can be used on any friction support.

Jan 1, 1983

By James P. Ludwig

This report provides the results of a two year study of the projected time and cost requirements for new mine development in Wisconsin and is based on a unique blend of information from mining company officials, state regulatory agency officials and contractor experience. Through formal cooperative and review agreements with Kennecott Copy per Corporation, Exxon Minerals Co., U.S.A. and Noranda Mines Ltd., and the Wisconsin Department of Natural Resources plus informal arrangements with knowledgeable Wisconsin persons, lists of the tasks and subtasks required to plan a new mine in Wisconsin were developed. Times and costs were assigned to all tasks and subtasks and these data reviewed by all cooperators. Critical Path Method Diagrams were then developed for a generalized mining project. Total time and cost for the premine planning process was estimated to be 25..1 years and 223 person-years of professional time excluding public affairs effort respectively. By eliminating redundancies in the process and by increasing project efficiency through early public review and participation, recom¬mendations were made to lessen the time and lower the cost of premine planning. The streamlining recommendations could shorten the overall critical path length to 18.16 years and lower the cost to 208 person-years of professional time excluding public affairs effort. The estimated distribution of professional effort (cost) for mine planning in Wisconsin approximates 50.5% for traditional mine engineering tasks, 36.6% for environmental-regulatory tasks and 12.9% for traditional geological-exploration tasks.

Jan 1, 1979

By Gilbert M. Farrior

Tests of resistance to molten metals , to oxidation at elevated temperatures , and to various chemical reagents were made for a series of compositions in the TiB₂ - CrB₂ subsystem . In reaction with molten metals , there was no noticeable difference in reaction of the various compositions in the ( Ti , Cr ) B₂ series . The oxidation tests were ( 1 ) a rising - temperature test in which the specimen temperature was increased 4° per minute to 1,200 ° C and ( 2 ) a constanttemperature test in which the specimen temperature was held constant at 1,000 ° C. Compositions near Tio.6 Cro.4 B2 had the best oxidation resistance . Ti。.6 The chromium- rich alloys showed marked superiority to the titanium- rich alloys in resistance to corrosion by the chemical agents investigated . The chemical reagents used were sulfuric , nitric , and hydrochloric acids and sodium hydroxide of different concentrations .

Jan 1, 1964

By H. F. Weaver

The 17th National First-Aid and Mine Rescue Contest was held in the Kentucky Fair and Exposition Center, Louisville, Ky., October 2, 3, and 4, 1957. The meet was under the auspices of the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with the National Coal Association, United Mine Workers of America, State mining departments, local mining institutes, and coal operators' associations. The Arrangements Committee, as authorized by the General Committee, made all the necessary arrangements for conducting the 1957 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators' Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1958

By Kenneth M. Maas

The Bureau of Mines inventoried the land in southwestern Alaska to classify ownership and availability and compared this land with known mineral terranes and mineral deposits. This report discusses and quantifies the potential for favorable location of mining claims for metalliferous (locatable) mineral deposits. Of the nearly 24 million acres that constitute the study area, approximately 3.6 million acres or 17% are available for mineral location, 3.4 million acres or 14% are available with restrictions, and 17 million acres or 71% are unavailable. Mineral terranes are known to underlie about 7.8 million acres or 33% of the study area; 3 million acres or 38% occur on land available for mineral location, 1.3 million acres or 17% occur on land available with restrictions, and 3.5 million acres or 45% occur on unavailable land. The State of Alaska has opened over 91 % of its land in the study area to mineral location; in comparison, the Federal Government allows mineral location on 0.07% of the land under its jurisdiction. There are 117 known mineral deposits or occurrences within the study area, including 77 lode deposits and 40 placer deposits. Of the 41 lode deposits occurring within a mineral terrane, 2 occur on available land.

Jan 1, 1988

By Jimmie C. Rosenbruch

The Federal Bureau of Mines evaluated the prospects for using geothermal energy to generate electricity for mines in remote areas. Given the development of a geothermal resource for this purpose, the subsidiary uses of space heating and agriculture were then examined to see if other industries might be viable given a cheap source of heat energy. Sites investigated were located in three areas of Alaska: Kobuk in the northwest, Unalaska in the southwest, and Stikine River in the southeast. Each site was relatively close to mineral deposits whose prospects for development would be enhanced with cheap power.

Jan 1, 1975

By R. W. Geehan

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Bureau engineers made a preliminary examination of the Morefield mine early in 1943 and recommended investigation by trenching and diamond drilling, The Bureau of Mines conducted work from August to December of 1943, which indicated that the Morefield mine was a favorable location for an experimental mining program. The Bureau of Mines carried on such a program from September 1947 to March 1949. The property investigated is 30 miles southwest of Richmond in Amelia County, Va. (fig. 1). During World War II mica and beryl were shipped from the Morefield mine, but after the high prices and premiums paid during the war years were not available the mine was closed.

Jan 1, 1953

By E. H. Denny

The presence in the Cripple Creek district, Colo., of irrespirable gas or gases, generally known to consist mainly of nitrogen and carbon dioxide, has been recognized by members of the mining industry in that region almost since underground mining was begun there; the occurrence, origin, and possible control of these gases have been discussed in several articles cited at various places in this report. Similar gases have also been studied in other metal-mining districts, as later discussed. In March, 1925, there were two fatalities from rock-strata gases in the shaft of the Index mine, near Cripple Creek. Two men repairing the bell or signal line preparatory to reopening the shaft were lowered into irrespirable gases and died. Their bodies were recovered by rescue crews from the United States Bureau of Mines and .the Portland mine, Victor, Colo. These crews found it necessary to use oxygen breathing apparatus. In October of the same year a miner was trapped on the 6 level of the Midget mine by an influx of gases that filled the shaft to a point above that where he was working. Oxygen breathing apparatus was again used by Bureau of Mines employees, who were in the vicinity, and the man was brought out in time to save his life. These two fatalities and one near fatality seemed to show that additional investigation of the gases and methods of control might be warranted. Accordingly, field and laboratory studies were begun by the authors of this report after a visit to the district by M. van Siclen, then engineer in charge, mining research division, Bureau of Mines, and after conferences with the Mine Owners' Association of Cripple Creek and with J. T. Joyce, metal-mine commissioner of the State of Colorado. The mine operators of the Cripple Creek district and the State mine commissioner's office gave whole-hearted cooperation in this work.

Jan 1, 1930

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

By W. G. Pariseau

A two-dimensional finite element program has been modified and extended to account for some of the rock mechanics complexities associated with single entry development of longwall coal mine panels. Program capability includes arbitrary assignment of element properties without regard to element ordering, anisotropic elastic, plastic and brittle rock properties that may be time dependent (aging), arbitrary mining sequences and provision for the effects of artificial support on the adjacent strata. Failure is according to an extended von Mises criterion that may be linear or quadratic in form; flow rules are obtained from the yield function taken as the plastic potential, but brittle behavior is treated as a discontinuous process of material properties change with deformation. In either case the extent of failure is calculated from the external boundary conditions. Application of the program to essentially two-dimensional problems resulted in lose agreement between calculated displacements and field measurements in the double entry system. Bleeder entries were stable in one locality and not in another. Artificial support had little influence on stability.

Jan 1, 1978

By S. Vennos

As a result of Synopsis 73-16 Dynadyne responded with an unsolicited proposal offering the Bureau of Mines to develop an ultra-low volume coal mine dust personal sampler. In the ensuing technical discussions the choice of a desirable volumetric rate became a focal point. While, the initial proposal was based on a volumetric rate in the area of 50 cc/min the Government expressed interest in a variety of mass flow rates ranging from 50 cc/min to 2000 cc/min. The physical characteristics such as weight, volume and configuration of a personal sampler are to a large extent - dependent on the operating volumetric rate. It became readily apparent that the optimum size of such an instrument as a function of volumetric rate was not known and that a study of the choice of optima was essential prior to beginning the development, Hence, the Government authorized a two phase approach to this project. Phase I was to include a Technical Evaluation Study of optimum characteristics in the range between 0. 1 to 2. 0 lpm. Based on these findings and in consultation with MESA personnel, the Bureau of Mines was to authorize the second phase that is, the development. Phase II, was to include the drawing of a set of performance specifications stating among others the desired operating volumetric rate. In this report, every effort was made not only to present the actual work done over the course of this development, but to reflect also our engineering "thinking" providing answers as to the "why" we preferred certain solutions over others. We believe that this added dimension is not only useful for the Government official evaluating this report, but also that the Government is entitled to it providing the official with an educational content useful in avoiding future costly repetitions of similar situations.

Jan 1, 1975

1. Domestic Production and Use: In 1982, 13 companies operated 30 primary aluminum reduction plants, with 3 firms accounting for 55% of production. Washington, Oregon, and Montana accounted for 34% of the production; Texas, Louisiana, Missouri, and Arkansas 18%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central and eastern States 34%. Based on published producer prices, output of primary metal in 1982 was valued at over $5.5 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 39% of domestic consumption in 1982, transportation 20%, building 14%, electrical 8%, consumer durables 8%, and other uses 11%.

Jan 1, 1983

By R. L. Soderberg

This paper is one of a series on mining methods and costs being published by the Bureau of Mines. It describes briefly the mining methods employed since the start of operations in 1937, with emphasis on the diamond-drill blast-hole method of ore breaking and slusher-drift method of ore drawing at the Holden mine of the Howe Sound Co., Chelan Division, Holden, Wash. The Holden mine is in the north-central part of the Cascade Range, 11 miles up Railroad Creek from Lake Chelan. The nearest railroad is at Chelan Falls, 40 miles by boat and 4 miles by highway from the mine. All freight comes into the mine and all concentrates are shipped out via Chelan Falls. The altitude of the main haulage level is 3,500 feet. Railroad Creek Valley is covered with a dense growth of fir and spruce, while most of the surrounding mountains are rocky, with sparse timber growth.

Jun 1, 1948

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By Charles S. Allbright

To develop a method for predicting the stability of a fuel during long-term storage from rapid aging tests at 200° F, the Bureau of Mines determined the stabilities of three gasoline base stocks and an alkylate blending stock in both sealed storage and aerated storage at 110° F for periods extending to 32 weeks. Stabilities of samples containing gasoline-additive compounds were compared by aging, using two methods--rapid aging in a bomb at 200° F for intervals up to 16 hours and storage at 110° F. The additives used were an uninhibited tetraethyllead motor mix, N,N'-di-sec-buty1-p-phenylenediamine and 2,6-di-tert-butyl-4-methylpheno1. Results were related by graphs that enable predictions of gum and sediment formation during storage from data obtained in bomb tests. A premium-gasoline base stock and the alkylate proved to be stable, but the two regular-grade gasoline base stocks were found to be unstable. Addition of the diamine antioxidant improved the stability of both of the regular gasoline base stocks, while the phenol antioxidant improved only one of them. The presence of the tetraethyllead decreased the storage stability of all four fuels, both with respect to formation of gum and precipitation of inorganic sediment. The rapid test at 200° F appears to offer promise as a basis for a method of predicting gasoline stability in long-term 110° F storage.

Jan 1, 1968

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By G. A. Smyres

The Bureau of Mines investigated a HCI-02 leaching procedure to recover Cu, Ni, and Co from a low-grade bulk sulfide flotation concentrate prepared from the Duluth gabbro complex. Since the Duluth gabbro complex is the largest known and unexploited Ni resource in the United States, the development of options for extracting the metal values from the flotation concentrate of this domestic resource is necessary. Conditions were determined for producing a pregnant solution low in Fe to facilitate recovery of the metal values. Leaching experiments were conducted at 15 pct solids, 1000 to 1200 C, 0.2 to 0.3 g HCI per gram concentrate in a 50-gal reactor pressurized to 50 pSig with 02. Base metal extractions from the concentrate were, in percent, 90 to 92 Cu, 99 Ni, 97 to 99 Co, and 0.1 .Fe. Precious metals extractions were erratic and unpredictable; at best their extractions were, in percent, 55 Au, 90 Ag, 40 Pt, and 45 Pd. The reaction time at 1200 C was 0.5 h. The use of compressed air instead of 02 as the oxidant was also investigated. Solvent extraction using LIX 622 was used to remove Cu from the pregnant solution. Cementation on Cu was tested for precious metals recovery, while sulfide precipitation was used to produce a Ni-Co product. A conceptual flowsheet for treating the Duluth gabbro concentrate is proposed.

Jan 1, 1985