Search Documents

By W. H. Carrington, A. C. Richardson

"INTRODUCTION The Powhatan mine of the Franklin Coal Mining Co. is located in the western part of Jefferson County, Ala., on the Louisville and Nashville Railroad, 40 miles west of Birmingham. The Mary Lee bed at this point yields coal with fair coking qualities, but with an ash content as mined so high as to prohibit its use in the production of metallurgical coke. At present the entire output of the mine is washed in single-compartment jigs and marketed as locomotive and domestic fuel.Figure 1 gives a typical seam section of the Mary Lee bed at the Powhatan mine. This section shows that the bed is divided by rock partings into three benches. In many parts of the mine, particularly in the older workings the roof rock is so weak that it can not be held without excessive timbering. This condition has restricted the operation in many parts of the mins to the middle and bottom benches of coal. The 6 inches of draw rock between the top and middle benches is very strong and makes an excellent roof requiring only a normal amount of timbering to support it. In the newer workings of the mine the character of the rock above the top bench is strong and it is believed that in the future it will be possible to work all three benches. This study was undertaken for the purpose of determining the washing characteristics of the Mary Lee bed at Powhatan and the effect on these characteris-tics of including or omitting the coal from the top bench. It was also the purpose of the study to show whether it would be possible to produce a washed product sufficiently low in ash to be used for the manufacture of metallurgical coke. This paper is one of a series of reports on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and tin University of Alabama. With the cooperation of the coal producers of Alabama. It contains the results of screen sizing and float-and-sink tests of representative samples of run-of-mine coal, and the results of table tests on the minus 3/16-inch sizes of the raw coal."

Apr 1, 1933

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world's four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and, (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke. This is the third of a series of reports giving results of studies by counties under part (1) of the investigation. This report covers Pike County, Ky., which comprises parts of the Harold, Williamson, Matewan, Gilbert, Pikeville, Regina, Hurley, Pound, and Clintwood quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By J. R. Thoenen

Up to 1914 almost all of the world's supply of potash came from Germany and Alsace. With the cessation of shipments from Germany during the World War the importance of a domestic supply was evident, During the past 15 years the United States has been working toward the establishment of a domestic potash industry which would end foreign dominance in this commodity. The Federal government has taken an active part in this program. As its share in the work, the Bureau of Mines has ascertained the potash resources in certain districts through core drilling and has engaged in a comprehensive program of research on the extraction of potash from its various minerals. Until the passage of the Winter bill (H. R. 496) by Congress in 1928 the Bureau of Mines had not been able to give any consideration to the western ores, wyomingite (leucite) and alunite. With the Passage of this bill, however, the ray was opened for the extension of the potash studies to cover these materials.

Jan 1, 1932

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By S. S. M. Chan

The Bureau of Mines has investigated the structural aspects of shafts and support systems using the finite-element technique. In situ field measurements in deep, vein-type metal mines show that rock stresses are often higher in the horizontal direction than the vertical, and unequal in the horizontal plane. These data and laboratory and field-determined physical properties were used as input to analytical studies. Various design and construction parameters were investigated to deter-mine the effect on shaft stability. Rectangular shafts were studied in detail to determine the effects of applied stress ratio, shaft orientation and dimension, influence of interbedded quartzite and argillite, and rock fracturing. Various support systems were analyzed, including concrete lining, timber, and steel sets. Circular configurations were investigated to evaluate yield zones and liner thickness. Elliptical shafts and time effects were briefly evaluated to illustrate shape and time effects and demonstrate the methodology. It is shown that the magnitude, direction, and ratio of applied stress and rock mass anisotropy are keys to determining shaft stability. A realistic conceptual framework was developed with which to examine the rock and support interaction in deep mine shafts. Structural analysis techniques overcome some of the historical difficulties with shaft de-sign by defining the field data requirements and structural sensitivity of various design and construction parameters.

Jan 1, 1985

By A. L. Service, C. C. Popoff

Phosphate deposits in Montana , Idaho , Wyoming , and Utah are important factors in the mineral , agricultural , and industrial economy in the western part of the Nation . This report presents background information , including geology , mining , beneficiation , processing , resources , and economics , assembled to provide a comprehensive introduction to a series of four area reports . About 20 percent of the Nation's phosphate is produced from the Western field where there were 6 surface and 9 underground mines in operation in 1963 . This region also has an estimated 58 percent of the Nation's phosphate reserves , and continuing development is assured by these abundant resources and an increasing demand for phosphate products . Long range forecasts indicate that the United States will continue to use increasing amounts of both agricultural and industrial phosphate products . Beneficiation has become an important part of the phosphate processing industry , and two flotation plants and several washing plants were in operation in 1963. Recent studies by the Bureau of Mines Metallurgy Research Center , Albany , Oreg . , have been directed toward developing flotation processes applicable to treatment of marginal phosphate rock . Other Bureau of Mines research is being directed toward improved methods of ore recovery , ground control , and mining .

Jan 1, 1964

By R. V. Ramani

This volume is the fourth of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume II: Dragline Model, and Volume III: Mine Coordinate Generator System. The Open Pit Materials Handling Simulator (OPMHS) was first developed" in 1971 and modified and updated in 1975. The present work is an update of the 1975 version and provides a direct link between the geology and reserves system and the various activities of the mining equipment in a mining system. Also, the modeling techniques in OPMHS/2 have incorporated a flexible method for describing various equipment (shovels, trucks, belts, trains, etc.), locations, their sequence of operations, place changes, and their interactions. These features allow for studying mining equipment selection, mining method analysis and reclamation planning. This report describes the Open Pit Materials Handling Simulator Version 2 (OPMHS/2). The report details the program features, operation, and application. Through an extensive set of appendices, the data input sequence, input variable definitions, sample data listing and program output are presented in detail.

Jan 1, 1985

By V. F. Parry

[Approximatel~r 7-1/2 illion tOlls of subb1tnminous coals are mined an-nuall in Colorado, Wyo~ing, and Montana, of which 50 percent probably reaches dome ,-tic conswno:os. r:L'he moi s t'_re of the se subbi t1.Uninous coal sis high, averae;:t.:ug about 25 :!,)ercent \-Then they are :nined. T'ne coals are non-caking d ~~ack to a vari ble degree when exposed to nornal atmospheric conditions. ~hey a~e gpod domestic fuels, are considered to be smokeless in most furn~ces, and have been used. f, r f!1an: y ars in hand-fired domestic furnaces in hich tnc practice i~ to e~ploy large lureps for efficient com-]

Jan 1, 1941

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts in Pershing County, Nev., made from March 9 to April 1, 1936. During the field work nearly all of the mining districts in the county were visited, and considerable data were obtained on active and inactive properties. The report covers the location of the various mining districts, nature of the deposits, information on past

Jan 1, 1936

By Harry Perry, Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition , a revision which would supply up- to - date information on coal research and which would facilitate communication among organizations of similar interest seemed important . This compilation includes the names and activities of organizations of various types -government , university , private , and industry . The areas of investigation that each organization is engaged in are indicated in broad terms : Analysis and constitution , mining and geology , preparation , briquetting , combustion , high- and low-temperature carbonization , gasification , conversion to solid and liquid fuels , and health and safety . Publications issued by and describing the work of each organization are cited ; almost all of the organizations also publish results of their investigations in the technical press . Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country . Information that would improve coverage and accuracy of the next revision of the publication will be welcomed by the Bureau of Mines .

Jan 1, 1966

By Glenn A. Shirey

The objective of this contract as to prepare a detailed, readily usable handbook on dust control techniques for longwall mining operations. Information was gathered from available literature, and through contacts with industry and government personnel. The handbook describes those methods of dust control applicable to today's longwall mining systems, and contains sufficient design elements to assist operators with problems in testing or implementing new control procedures. Complete reference lists are presented at the end of each chapter to direct the reader to additional information.

Jan 1, 1985

By T. E. Gray

This report describes the preparation characteristics of the three significant coal beds in Greene County, Pa. It is one of a series planned to determine which coals are suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 12.5 million tons of coal was produced in Greene County in 1956, of which approximately 10 million tons was cleaned mechanically in 8 cleaning plants. The Bureau of Mines has estimated that 3.5 billion tons of recoverable coal remained in the county as of January 1, 1954.

Jan 1, 1958

By Oliver Bowles

In 1943 the Bureau of Mines began a review of trends in consumption and prices of the more important nonmetallic minerals. The first report covering building materials4/ appeared in December of that year. The present paper, which deals with chemical raw materials and fertilizers, is the second of the series. The 34 years from 1910 to 1943, for which statistics are presented herein, comprise periods of uneventful peace, unparalleled prosperity, industrial depression almost to the point of stagnation, and two wars of world proportions.

Jan 1, 1945

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious. In addition to agricultural and building lime the sales statistics compiled annually by the Bureau of Mines include lime sold to the steel and other metallurgical industries as refractory and fluxing material, as well as that used by paper mills, glass works, tanneries, and water-treatment plants. These major uses normally consume about 86 percent of the domestic sales. The remaining 14 percent includes lime sold for use in the manufacture of alcohol, alkalies, bleaches, calcium acetate, calcium carbide, coke gas and byproducts, glue, insecticides, oils and fats, paints, and rubber, in the refining of salt, in the manufacture of sand-lime and slag brick, in the disposal of sewage and garbage, in the manufacture of silica brick, in the refining of sugar, in the textile industries, and in wood distillation. Many other uses are also known for which complete sales data are not available.

Jan 1, 1934

By J. F. McCoy

As mining develops into deeper and hotter regions, the safety and health of miners require that the workspace be cooled. Toward this end, this program has successfully developed a high performance, low maintenance spray cooler of 5000 cfm nominal capacity. Further, a series of four 25,000 cfm, nominal capacity, spray coolers has been built and mine tested with satisfactory results. The smaller coolers have been patented and become commercialized with 50 units currently in service. The concept has been developed independently overseas with an unknown number of units in operation.

Jan 1, 1984

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. The 15 countries that constitute the region accounted for 28% of world crude petroleum output, 17.2% of world natural gas plant liquid production, and 5.3% of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. About 66% of total world crude petroleum reserves and 31 % of total world natural gas reserves are in the Middle East. Transportation and port facilities in the region are geared to expediting efficient and rapid shipment of these materials. Export sales of these fuels provide funding for further diversification of the mineral industry. Additional development of downstream facilities for producing energy-intensive metals such as aluminum and byproducts of the fuels such as petrochemicals and fertilizers can be expected. Earnings from the industry are also channeled by several Governments in the region to mineral industry projects in Africa and elsewhere. Several countries in the region own major petroleum refineries and distribution facilities worldwide. Petroleum prices rose overall during the year owing to the invasion by Iraq of Kuwait in August 1990. Output from both countries, the fourth and fifth largest producers, respectively, in the Middle East, was negatively affected by the war. Kuwaiti crude oil wells and pipeline facilities suffered extensive war damage while exports of petroleum and petroleum refinery products by Iraq ceased owing to a U.N. embargo. The embargo also impacted Jordan, an exporter of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was more than made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion of the increase.

Jan 1, 1992

By Robert L. Kranz

Mining-induced microseismicity data collected by the U.S. Bureau of Mines in a hard-rock mine were analyzed for spatial and temporal patterns that might prove useful for prediction of rock bursts or assessment of rock mass damage changes. Pattern attributes described and illustrated in the previous report (part 1) were applied to the study of aftershock sequences associated with two different stopes. The aftershock sequences were spatially and temporally fractal, and the fractality was maintained for up to 16 h following a sequence progenitor. This suggests mechanical interdependency among the after-shocks. No statistical difference was found in the distributions of fractal dimensions when comparing two different stopes or when comparing aftershock sequences initiated by blasts or bumps. This suggests a lack of sensitivity to both stress perturbation mechanism and local damage states. However, differences between the two stopes were found in other sequence attributes that support inferred differences in the magnitude of stress concentrations and damage near each stope, and over time as a stope is developed.

Jan 1, 2010