Search Documents

By Thomas J. Peters

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 15,600 acre (6,310 ha) Freel Peak RARE II area (No. 5271) in the Lake Tahoe Management Unit. This study by the Bureau of Mines indicates that potential for economic mineral resources in the area is slight. The only mineralized structures in the area consists of two quartz veins. One quartz vein, at the Mountain Top Mine (fig. 1), located by Fred Denner in 1932, is estimated to contain 2,000 tons (1,800 t) of silver and copper-bearing resources. Chip samples from the vein averaged 0.61 oz silver per ton (20.91 g/t), and 1.59 percent copper. The narrow vein is not economically mineable. The other quartz vein is poorly exposed and contains traces of molybdenum. A second reported molybdenum occurrence could not be substantiated.

Jan 1, 1982

By W. H. Oppelt

Two exploratory gasification tests of limited duration were made at Dorsten, Germany, with strongly coking Pittsburgh-bed coal in a fixed-bed pressure gasifier. To reduce the coking potential of the Arkwright coal, ash refuse from the gasification of Dorsten (Leopold) coal was added to pre-pare coal-ash mixtures which contained nominal 20 and 30 percent ash. Major adjustments in principal process variables at the beginning of the tests resulted in wide fluctuations in the rate of gas production, gas offtake temperature, and carbon dioxide concentration in the gas. Because a higher steam-to-oxygen ratio was used in the tests than was customarily employed for routine operation, gas production was lower, and steam and oxygen consumption was higher. After operating conditions had been improved, the results of a 12~-hour-long test with addition of sufficient ash refuse to obtain a nominal 30 percent ash concentration indicated that operation is feasible with this coal mixture using a fixed-bed pressure gasifier equipped with a rotating coal distributor and stirrer.

Jan 1, 1966

Electrical trailing cable used to power coal mining machinery is frequently damaged by tensile strain or crushing by mining machines running over the cable. A major problem is finding the exact location of a short or open in this cable so it may be repaired. A major problem is finding the exact location of a short or open in this cable so it may be repaired. FMC Corporation was awarded modification III to USBM Contract H0122011 to continue development and testing of cable fault locators, resulting in delivery of: 1. A prototype electrostatic/electromagnetic/ TDR transmitter and an electrostatic/electro-magnetic receiver sot that: o Locates cable faults by time domain reflectometry o Locates opens by detecting electrostatic signals o Locates shorts by electromagnetic coupling. 2. A prototype infrared detector and an infrared detector power supply that heats a shorted area by applying high current (at low voltage) and locating a short by infrared output. 3. Twelve production infrared detectors. 4. Detail drawings for all of the developed instruments.

Jan 1, 1973

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization; and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed 'and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number S0241073 by Fenix & Scisson, Inc. to the Denver Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By James C. Barker

The U. S. Bureau of Mines made a reconnaissance In the western Crazy Mountains for cobalt and associated metals as part of the Alaska-wide critical and strategic metals program. The area, located about 75 miles north of Fairbanks in central Alaska, is underlain by complexly faulted, predominantly clastic sedimentary rocks bordering the Tintina Fault system. Above background metal concentrations were found to occur in altered fault zones, tectonic breccias, soils, and ground water seeps and precipitates that either cut or are derived from the faulted clastic sedimentary rocks. Up to 0.115 pct cobalt and more than 2.0 pct zinc were detected in soil samples. Spring precipitates contained up to 1.3 pct zinc, 0.037 pct tungsten, and other metals. Some localities lacked cobalt but contained anomalous amounts of copper, lead, zinc, silver, and other metals. No outcropping of primary metallic minerals was located because of Colluvium and vegetation cover and extensive deep leaching. Therefore, whether the metal values encountered are due to primary deposits with economic development potential or are the results of concentration by ground water from low-grade sources is unknown. The presence of cobalt, nickel and zinc, and the identification of minor tin and tungsten indicate that further investigation is warranted.

Jan 1, 1983

By R. C. Corey

GERMANIUM is an element that has come into widespread use in the electronics industry in recent, years. So far this increasing demand has been, met by ample supply: however, the future balance is uncertain, and the need has been recognized to discover additional domestic sources of germanium. This investigation was conducted to study the possibility of obtaining a potential supply of germanium from coal or coal ash. It has been known for some time that coal contains germanium; the discovery that By ash from coal-fired boilers often contains appreciably more germanium than the original coal suggested the possibility that coal ash might be an abundant and economical source of this element. In this study the concentration of germanium was determined in numerous samples of coal and ash. A number of miscellaneous waste materials also were examined in the course of the investigation; the results are reported as a matter of general interest. The methods and equipment employed are discussed in detail. Sample-preparation and analytical techniques are described in the appendix. Spectrographic analyses were made on a total of 639 samples, including coal, coal ash, slap ash from lignite and peat, wood ash, and various inorganic materials. Qualitative analyses were run on all samples, and quantitative determinations were made on those samples that contained enough germanium to be measured by this method The lower limit at which germanium can be determined quantitatively by spectrographic analysis is 50 parts per million (p. p. m.), but concentrations of less than 20 p. p. m. can be detected qualitatively.

Jan 1, 1959

This Bureau of Mines publication summarizes the industrial minerals industry of Idaho. It contains information on 119 principal deposits of 21 commodities in the State and describes the institutional and infrastructural factors affecting mineral development.

Jan 1, 1991

By A. Gene Collins

Rapid, sensitive, and precise methods of determing major, minor and trace constituents of oilfield brines are needed. Several methods have been developed or adapted by the Federal Bureau of Mines at the Petroleum Research Center, Bartlesville, Okla. The following methods are described in this report: Spectrophotometric and volumetric for iodides and bromides; potentiometric for pH, alkalinity, acidity, borate boron, total boron, and organic boron; gravimetric for potassium; disodium ethylenediaminetetraacetate (EDTA) volumetric for total hardness, calcium, and magnesium; spectrophotometric for fluorides; and color comparison .for arsenic. Adequate sensitivity, precision, and accuracy were obtained for each method. The Bureau of Mines pioneered in research on the analysis of oilfield waters (2, 46, 47).6 However, several of these early procedures were quite time consuming. Also, they did not include methods for determining trace and minor constituents of brines.

Jan 1, 1961

By J. Mitchell Linne

The principal mineral commodity in the Orleans Mountain RARE II area (No. 35019) is gold. Gravel deposits along the Salmon River contain placer gold. Lode gold with associated silver is contained in quartz veins. Many placer mining claims have been located within the study area in the Salmon River district. Four placer patents totalling 230 acres were issued for claims on the Salmon River between Lewis Creek and Forks of Salmon. On this same reach of river, adjoining and overlapping the study area boundary, approximately 3.3 million cu yd (2.5 million cu m) of gold bearing gravel with values ranging from $0.51 to nearly $5 per cu yd (50.66 to $6.50 per cu m) (gold valued at $400 per troy oz), are contained in three placers, the Bloomer, Pot Luck, and Horn (table 1). Within the study area boundary there are approximately 950,000 cu yd (726,000 cu m) of gold bearing gravel in these three placers. These three mines yielded nearly 12,000 oz (373,000 g) of gold and more than 300 oz (25,000 g) of silver between 1872 and 1913.

Jan 1, 1982

By G. D. Andria

Contract J0275007 was to consist of a thorough two-phase statistical analysis of respirable coal mine dust data from USBM Contracts H0232061, H0232060, H0230029, H0230031, H0210050, and H0242013. Consequently, BCR cataloged and assembled relevant data items from these contracts and formulated procedures suitable for the evaluation. The selected procedure was a Multilinear Regression Analysis which related dust concentrations measured in the mine to other mine parameters. Under the first phase, a thorough analysis of the date from USBM Contract No. H0230029 was completed. Primary results from this analysis are as follows: (1) The five variables that significantly affect dust concentrations in the return behind the brattice are the spray system utilized; the distance from the face to the return brattice; the return airflow; the production rate; and the water consumption rate, in that order. These five variables describe about 85 percent of the total variation in the return dust concentration. (2) Results at the miner and jack-setter locations were somewhat less conclusive due to the fact that only 17 percent of the variation in dust at the miner could be resolved and only 48 percent of the variation at the jack-setter location could be explained. The decision of the sponsor was that these initial results revealed as much information as could be expected; thus, per instructions from the USBM, the second phase (analysis of the other five contracts) was abandoned.

Jan 1, 1978

By William J. Campbell

Expansion measurements of platinum, added as an internal standard, are used for thermal calibration of X-ray cameras and diffractometers. Accuracy of the temperatures derived by this technique depends on the precision of expansion measurements and the reliability of reference expansion data. Temperature measurements to ± 1° C. require ?d or ?a to be determined within ± 0.001 percent. Selected expansion data are concluded to be reliable to 2° C., 5° C., and 25° C., over the temperature ranges 0° C. to 700° C., 700° C. to 1,000° C., and 1,000° C. to 1,700° C., respectively. Tabular expansion values from 25° C. to 1,700° C. in 2° C. intervals were calculated from the following equation; Expansion, percent = [8.91 + 1.28 x 10-3(t-25) + 0.04 x 10-6(t-25) ] [t-25.104 ] These tabular values facilitate future corrections of published temperatures as more reliable expansion-temperature data become available.

Jan 1, 1962

By William Seymour, L. D. Schmidt, J. W. Myers, W. T. Reid

"This investigation was conducted by the Bureau of Mines as part of a program of the Solid Fuels Administration to encourage the utilization of anthracite fines, the objective being to determine the practicability of using anthracite fines in the manufacture of packagedThe experimental loss of packaged fuel covered by this report were made at a commercial plant using the Glenn Smith process and ordinarily making packaged fuel from Pocahontas screenings. These lots included several made from straight antimacite mines and others made from various blends of anthracite fines with four different bituminous coals. In all cases an asphalt binder was used. Determinations of the physical properties and the cobustion characteristics o the various samples of packaged fuel were made by the. Bureau of Mines at the Central Experiment Station.The physical tests indicated that a packaged fuel of sufficient strength for ordinary handling can be made from straight anthracite coal or from a wide variety of blends of anthracite fixes with bitunimous coal, using asphaltic binder. However the combustion tests indicated that packaged fuel made from anthracite alone tended to crumble excessively during burning and that as much as 30 to 50 percent of a caking coal may be required In the mixture to produce a block having satisfactory combustion characteristics.The authors wish to acknowledge the. splendid cooperation of Messrs. H. W. Kelly, J. L. Mooney and C. H. Stoss of Columbus, Ohio, who were chiefly responsible for obtaining the materials and making all the arrangements necessary for the production of the packaged fuel for testing.Thanks are due to the officials of Carnegie Institute of Technology for the use of their Olsen. Testing Machine and to H. M. Cooper and W. A. Selvig of the Bureau of Mines for analyses and tests."

May 1, 1946

By Joseph B. Cummings

"INTRODUCTION The property was first examined by an engineer 3/ of the Bureau of lanes in December 1942 and was later investigated by the sane engineer in January and February 1943. Prominent outcrops and underground exposures of high-grade iron ore, together with mention of sizable intersections of hematite in logs of four widely scattered churn—drill holes, indicated the possible occurrence of a substantial tonnage of iron ore at this old copper producer.From March to May 1943, detailed topographic and geologic mapping of the property was done by the Federal Bureau of Mines, the Federal Geological Survey, and the Arizona Bureau of Mines.Funds were allotted for exploration of the property by churn and diamond drilling. This work was started in December 1943 and completed in June 1944.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts, developed by each exploratory project as soon as practicable after its conclusion. The Mining Drench, Lowell B. Moon, Chief, conducts preliminary exmination, performs the actual exploratory work, and prepares the final report, The Metallurgical Branch, P. G. Knickerbocker, Chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision Dr. R. S. Dean, Assistant Director."

Dec 1, 1946

By R. Emmett Hughlett

The Bureau of Mines has developed a statistical approach to the laboratory evaluation of response bias and precision in gas detectors. The techniques described employ a computerized analysis and a new method of data presentation called composite graphing. The underlying theory, its practical application to the data, and the experimental equipment and procedure are described.

Jan 1, 1982

By M. D. Balen

The U. S. Bureau of Mines has undertaken the development of mineral industry cost escalation factors to enable the estimation of mineral development and extraction costs for mineralized sites in Alaska throught the use of the Bureau's Cost Estimating System v2.0 (CES 2.0). For the purposes of this document, all calculations are based on, and reflect the economic environment in Alaska in July 1992. The greater cost of mining in Alaska as compared to the contiguous-48 States can be estimated for Alaskan mining operations through (1 ) the analysis of capital and operating costs for analogous mine and mill plants in operation in the contiguous-48 States; (2) the hypothetical relocation of mine and mill plants from their actual location(s) to Alaska by making engineering modifications to the mine and mill plant design as required by the Alaskan site characteristics; (3) calculation of the cost of the required engineering modifications and; (4) the escalation of all costs to a level representative of the economic environment in Alaska at some specific point in time.

Jan 1, 2011

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

By H. Stanley Benson

This report is an account of research conducted to improve the performance of and then further field test Draft Power Sensor (DPS) equipment, the use of which enables a bulldozer operator to optimize his machine's work rate. Significant improvements were made in DPS hardware, and extended field testing was conducted at two working strip mines: the Glenharold Mine of Consolidation Coal Company, near Stanton, North Dakota, and the Beulah Mine of Knife River Coal Company, near Beulah, North Dakota. This report documents the increase of bulldozer work production by greater than twenty percent while using the Draft Power Sensor when compared to baseline work production without benefit of the Draft Power Sensor. Research was done by Southwest Research Institute under contract with the Bureau of Mines.

Jan 1, 1980

By Francis X. Cannaday

Equipment and techniques were developed with Bureau of Mines facilities for measurement in the laboratory of sonic shear wave velocity in variously shaped rock specimens in a wide range of sizes. A variety of rock types was tested. The shear wave front is produced by electronically excited, piezo-electric ceramic) disk-shaped transducers. Transmitter and receiver are interchangeable. Special equipment components were Bureau produced; other components were commercially available. The equipment permits quick measurement of shear wave velocity on variously shaped specimens with a minimum of specimen preparation. The technique, under favorable conditions, allows for determination of the moment of arrival of the shear wave when it is superimposed on a weak longitudinal wave.

Jan 1, 1968

By Clyde L. Holmberg, Paul Zinner

"INTRODUCTION In view of the large tonnage of low-grade iron ore and iron-bearing material known to exist at the western limits of the Gogebic range, the Bureau of Mines undertook an investigation of the area for the purpose of evaluating the iron-bearing formations as sources of iron for possible future utilization.After 6o years of exploration an, development on the Gogebic range, the area investigated by the Bureau represents the known western limit of direct-shipping ore mined from operations on the Gogebic range.An area about 2 miles in length between the villages of Pence and Iron Bolt in Iron County, Vic., was selected for investigation, and trenches wore excavated through the overburden and fully across the iron-bearing formation to obtain 108 bulk samples for beneficiation tests. Exhaustive tests involving gravity and flotation methods, magnetic separation, and magnetizing roasts followed by magnetic separation were conducted on the samples to determine the ammability of the individual formations and the entire iron-bearing zone to beneficiation.Empirical data on the character and mineral content of the formations arc tabulated herein, as well as the results of the beneficiation tests."

Dec 1, 1947

By M. Carrales

This Bureau of Mines report presents information on the sulfur content of crude oil in the United States and in some foreign countries. Data are presented for oil produced in 1971 from fields in 26 States that accounted for about 76 percent of total U.S. oil production; the foreign data cover fields in 24 foreign countries that accounted for about 64 percent of the total oil produced from these countries in 1971. Most of the data are presented in tabular form.

Jan 1, 1975