Search Documents

By Bertrand L. Johnson

Barite, the natural sulfate of barium (BaSO4), is the most important barium mineral. Normally it is white (opaque to translucent), but impurities sometimes render it yellow, gray, blue, brown, red, or black. Brown or red stains are commonly caused by iron oxide. Barite is unusually heavy (specific gravity, about 4.5); in fact, it is one of the heaviest of the nonmetallic minerals. It is brittle and fractures unevenly. The hardness of barite ranges from 2.5 to 3 but is usually about 3. It can be scratched by a copper coin. Pure barite contains 65.7 percent BaO and A.3 percent S03. Much of the crude barite ore mined, however, contains impurities; thus it has a lower content of barite and consequently less barium oxide. Commercial analyses show its total BaSO4 content. Barium also occurs in nature as the mineral witherite (BaCO3), which, however, is not common in the United States, and commercial deposits have been found only in California. Witherite is a yellowish-white, light-gray, or Kite mineral with a specific gravity of about 3, a hardness of 3 to 4, and an uneven to subconchoidal fracture.

Jan 1, 1941

By Robert S. Hill

"In November 1942, a preliminary report on the Swartz Mining District by John H. Soule, an engineer of the Bureau of Mines, recommended an exploratory program of diamond drilling. The existence of zinc and lead deposits in this region had been known for many years. In 1943 and 1944, the Federal Geological Survey made a detailed study of the same area. Later work done by the Bureau of Mines in this district followed the suggestions made by these geologists.3/In the latter part of 1944, Felix A. Vogel, Jr., another Bureau engineer, made a study of the Grey Eagle mine in the Kingston Mining District, a few miles northeast of the Swartz district, and his recommendations for diamond drilling were followed in so far as funds permitted. Drilling was started in October 1943 and was completed in June 1945.4/In its program of exploration of Mineral deposits, the .Bureau of Mines 'Ms as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution t national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.With respect to this report, special acknowledgment for assistance is due to C. H. Johnson, chief of the Rolla Division, Mining Branch, and to various members of the Geological Survey."

Sep 1, 1946

Arsenic.--Inorganic arsenic has been added to the Environmental Protection Agency's list of hazardous air pollutants because of a high probability it can cause cancer. EPA estimates that inorganic arsenic emissions into ambient air total more than 6,000 tons per year, with about 65;L of this coming from the operations of copper, lead, and zinc smelters. Asbestos Detection.--In June 14, the President signed S. 1658 providing $172.5 million to detect and remove asbestos hazards in schools. Asbestos Use Must be Reported.--All firms using asbestos in the manufacture of some 30 categories of products must describe in detail how they use the mineral to the Consumer Product Safety Commission, for all manufactures since January 1, 1977.

Jan 1, 1980

By K. C. Dean

During the course of the investigation of manganese mineral occurrences in the western United States, the Bureau of Mines collected several lots of ore' from properties in the vicinity of Winkelman, Ariz. As none of the ores would be marketable directly, an investigation was made to determine their amenability to concentration by ore dressing. The Geronimo group of claims is in Pinal County, 8 miles west of Winkelman, Ariz. The manganese oxides occur as cementing material in ore zones of conglomerate. Representative samples of a 2-ton lot of ore cut from outcrops of two lenticular deposits were laboratory-tested. Two 1-ton samples from the Benningfield property were similar in physical characteristics but differed in grade. This claim is 11-1/2 miles south of Winkelman and about 1 mile west of the San Pedro River on the south side of Putman, Wash. The manganese minerals occurred as nodules and lenses, replacing limestone, in a capping over a dark, igneous dike. The North Star group consists of five claims on the west side of the San Pedro River 14 miles south of Winkelman. The ore consists of a low-grade, manganese oxide-calcite occurrence interspersed with stringers of higher-grade material and is present as filling in a fissure zone in porphyry. Two samples were obtained by the examining engineer; one sample represented run-of-mine material, the other represented ore from the vein that could be hand-sorted or selectively mined.

Jan 1, 1952

By E. G. King

The Bureau of Mines made experimental determinations of the heats of formation of forsterite and chrysotile at 298.15° K. The heat capacities of two polymorphs of serpentine, chrysotile and antigorite, were measured over the temperature range from 50° to 298° K and the entropies at 298.15° K were evaluated. The heat content of antigorite above 298.15° K was measured to 850° K. These thermochemical data were combined with other pertinent data to give heat and free energy of formation values at high temperatures. Free energy values are given for the reaction, forsterite + water = brucite + serpentine at different temperatures and pressures.

Jan 1, 1967

By C. M. McCulloch

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°. This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By Kenneth Wardell

Those flat lying, bedded or replacement, non-fossil fuel deposits which exist within the U.S.A., and which are amenable to longwall mining, are identified by reference to three principal factors associated with their physical/geological environments. These are their depth, extent and structural continuity. Technical feasibility is assessed in relation to the likely cutting speeds which can be achieved in the identified minerals with existing longwall shearer machines. Economic comparisons are made between traditional mining operations in those deposits for which technical feasibility is demonstrable. Continents are made concerning those technical deficiencies which appear to preclude the application of existing longwall equipment to the identified deposits and suggestions are made regarding the lines of research aimed at improving longwall technology.

Jan 1, 1978

Aluminum Production. -By October 1, Aluminum Company of America will restart a 35,000-ton-per-year unit at its aluminum smelter at Rockdale, Tex., restoring that facility to its full capacity of 325,000 tons annually. Primary Ingot Price Increase. -Most U.S. aluminum producers in mid-September were quoting a price of 72 cents per pound for primary aluminum ingot. On September 19, Kaiser Aluminum & Chemical Corp. announced that it would increase the price of primary aluminum ingot 4 cents to 76 cents per pound.

Jan 1, 1980

New GSP Trade Status Approved.--President Carter, by Executive Order effective March 30, has approved Generalized System of Preference treatment for imports of nonferrous metal products and other imports from Ecuador, Indonesia, Zimbabwe, Uganda, and Venezuela. As of May 2, Afghanistan and Ethiopia will be taken off GSP status. Under the Generalized System of Preferences, certain imports from developing countries are provided duty-free treatment. A country can lose its GSP status if its shipments of the product exceed $41.9 million or more than 50% of total U.S. imports during the preceding year. However, the President can waive the 50% rule in cases where total U.S. imports of an item in 1979 were less than $1 million. Certain nonferrous imports from Mexico, Peru, Chile, and Zambia are already covered by GSP. Hearings April 10 on International Tin Agreement.--The Fifth International Tin Agreement of which the United States is a signatory, which entered into force on July 1, 1976, will expire on June 30, 1981. A negotiating conference for a Sixth International Tin Agreement will be held under auspices of the United Nations at Geneva from April 14 to May 16, 1980.

Jan 1, 1980

By Francis J. Fratttali, Verda McLendon, Stanley J. Green

"INTRODUCTION During the first phases of the war emergency the shortage of aluminum prompoted the Bureau of Mines to investigate methods for using low-grade bauxites of high silica content and also clays as raw-material sources of this strategic metal. The Bayer process treats low-silica bauxites to provide the industry with a major portion of the purified alumina, which contains very low percentages of silica and other impurities. One of the methods investigated in the laboratories of the Bureau of Mines for low-grade materials is the lime-soda sinter process, which was studied on a pilot-plant scale. In this process, the alumina content of the alumina-bearing minerals Bs made water-soluble by sintering the raw material with limestone and soda. Simultaneously, the siliceous material is rendered insoluble. The sinter is extracted with an alkaline liquor, and the resulting extract liquor is treated as follows to recover the alumina: (1) Autoclaving with lime to remove silica as a zeolitic complex and (2) treatment with CO2 to precipitate alumina as the trihydrate (A1203.3H20). Figure 1 is schematic flow sheet of this process.As the process is cyclic, it is necessary that nearly all of the soda and alumina remaining in the plant liquors after carbonation be recovered. Upon passing through one cycle, these liquors contain 14 to 15 percent NaCO3 2 to 5 percent NaOH, 1 to 3 percent A1203, minor amounts of silica, and, with certain materials such as Pennsylvania diasporic clays, 0.5 to 1.0 percent Na2S04. Approximately 50 percent of the Na20 in these liquors must be returned, as soda ash, to the dry-grinding and raw-materials blending operations. Previous work (6)5/ on sulfate-free solutions demonstrated that two methods for recovering Na20 were feasible, namely: (1) Salting out Na2C03.H20 by evaporation of the carbonated solutions and (2) crystallizing Na2C03.10H20 by cooling the concentrated carbonated solutions."

Sep 1, 1947

By D. K. Ingram

In situ horizontal stresses were measured to determine the influences of geologic anomalies on the regional horizontal stress field in two coal mines in southern Illinois. Stress measurements were obtained near a normal fault having a 121-ft displacement at the AMAX Wabash Mine and a large coalbed want at the Kerr-McGee Galatia No.5 Mine. Horizontal stress measurements were completed using a Bureau of Mines borehole deformation gauge. The average maximum and minimum horizontal compressional stresses at the Wabash Mine were 1,400 and 800 psi, with the direction of maximum stress ranging from N 78° W to N 83° E. At the Galatia No.5 Mine, the averages were 1,500 and 500 psi, with the direction of maximum stress ranging from N 85° E to N 75° E. Generally, the geologic anomalies appear to have no dramatic effect of the regional horizontal stresses. However, subtle differences between stress measurements suggest an influence by the fault zone at the Wabash Mine. The larger anisotropic stress conditions at the Galatia No.5 Mine could be responsible for the increase in kink zones and directional roof failures.

Jan 1, 1988

By G. A. Apell

"SUMMARYThe quality of Moose Creek coal is considered superior to that of any now being produced in the Matanuska field of Alaska. In rank it is classed as roar coking high-volatile B bituminous coal.At present the Moose -Creek mines are accessible from the Glenn highway by 6 miles of well-maintained gravel road. The nearest railroad loading point is Moose Creek siding; 7 miles by road from the Buffalo mine. Palmer, 12 miles south of Buffalo mine, is the nearest town. Anchorage is 50 miles south of Palmer by road and-railroad.Core drilling and trenching by the Bureau of Mines revealed 2,375,500 short tons of coal in the Buffalo series on the Buffalo Coal Co. leasehold. Of this, 514,200 tons is considered measured coal and 489,900 tons indicated coal. Existence of deeper beds over the same length increased the tonnage of coal of all categories to 3,279,300 tons. The property has an assumed life, of 16 to 22 years, depending on the number of beds mined, based on an output of 500 tons of coal a day and 100-percent recovery. Coal from some of the beds car be marketed without washing however, a washery is necessary if all beds are mined. Beds in the Buffalo series not mined in the ""first mining"" will be irrecoverable at any later date.The Bureau of Mines completed exploration of approximately one-third of the local coal-bearing areas during 1943. Knowledge gained from this work makes it possible to investigate the rest of the area by drilling an estimated additional 5,000 foot of hole."

Dec 1, 1944

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

Antitrust Investigation Dropped. - The Department of Justice announced that it was dropping its 5-year investigation of the aluminum industry. The investigation was over whether the aluminum companies were acting as if they were a shared monopoly. Deep Seabed Mining. - The Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) has established an Office of Ocean Minerals and Energy which will be responsible for implementing the Deep Seabed Nard Minerals and Energy Act and the Ocean Thermal Energy Conversion Act. It will establish licensing and regulatory programs.

Jan 1, 1980

By C. W. Davis

This paper is the second of a series of progress reports on a study, of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value. One ,of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although Several manganese minerals acre readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.§. Recent experiments have shown that a roast at 650 to 900°C converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution. Introduction of smelter gases containing as much as 5 per cent SO2 during such a roast would not add much to the cost of the operation and might result in the formation of considerable water-soluble manganese sulphate.

Jan 1, 1930

By C. C. Merrill

The Bureau of Mines beneficiated the wastes generated by commercial titanium chlorination operations to reclaim metal values and reduce the problem of disposing of solid wastes. A water leach solubilized about 40 percent of the dry weight and over 75 percent of the metallic impurities. The residue from the water leach was rich in titanium dioxide and carbon; it was combined with rutile and recycled to a laboratory chlorinator. The contained carbon was used in lieu of part of the coke requirement.

Jan 1, 1969

By Ronald S. Conti

A new U.S. Bureau of Mines 6.8-L ignitability furnace was used to study the thermal autoignitability of dust clouds. This furnace has a quartz window to allow observation of the early stages of the ignition process and to allow measurement of the dust explosion temperature. Thermal ignitability data were obtained for various carbonaceous and metal dust clouds, with particular emphasis on various ranks of coal dusts. One of the reasons for the construction of the new 6.8-L furnace was to evaluate the effect of chamber volume on the measured autoignition temperatures. Therefore, data from the 6.8-L furnace were compared with data measured earlier in a 1.2-L furnace. The conclusion is that the autoignition temperatures measured in the 6.8-L furnace were only slightly lower on average than those from the 1.2-L furnace. These data on the minimum autoignition temperatures of various materials will be useful in analyzing the thermal ignition hazards of dust clouds in the mining industry and other industries that manufacture, process, or use combustible dusts.

Jan 1, 2010

By C. W. Davis

This paper is the second of a series of progress reports on a study of the hydrometallurgy of manganese which is being, conducted in an endeavor to make possible utilization-of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of S02 gas on manganese oxides at elevated temperatures may prove of value.

Jan 1, 1930

The first metal-mine accident-prevention course was prepared and published in 1942--45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' Circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By D. J. Parker

Because of its convenience and availability, natural gas (and to a much less extent manufactured gas) in being used more generally throughout the country for domestic and industrial purposes. With this use, specific and little-recognized hazards have arisen owing principally to the fact that the public and the consumer lack knowledge of the explosive property of this fuel. During the past 8 years gas explosions hove occurred in public and private buildings with loss of more than 300 lives and injury to many others. Such appalling catastrophes can and will be prevented if and when the necessary precautions are taken in the construction of buildings and the installation and maintenance of gas lines and gas appliances, plus adequate supervisions inspection, and education.

Jan 1, 1941