Search Documents

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By Gerald R. Coonan

I'm really here to talk about my pet subject of government relations. I've been in Peabody's Environmental Quality Department, working on regulations, for over five years, and I have seen a number of individuals in the coal industry who were completely stunned when a new regulation was brought to their attention. Their first reaction was, "where did this come from"?

Jan 1, 1980

By Jon Hurt, Brent Meins, David Vardiman

"Two test blasts were conducted at the Sanford Underground Research Facility to establish optimum blast designs and to limit blast effects on existing research rooms and equipment in preparation for the largest deep underground excavation in North America. Located on the 4850 Level (4,850 ft below the surface)at the former Homestake Mine in Lead, SD, this excavation is part of the U.S. Department of Energy’sLong-Baseline Neutrino Facility that will house particle detectors for the international Deep Underground Neutrino Experiment hosted by Fermilab. A large array of seismographs was deployedthroughout the 4850 Level to measure ground vibrations and airblast pressures in tunnel drifts and in lab spaces."

Jan 1, 2017

By Catherine Johnson, Barbara Rutter

The shock tunnel located at the Missouri University of Science and Technology Experimental Mine is 65 feet 9 inches (20.0406 m) in length. The tests performed inside of this tunnel are either arena tests or shock interaction and transfer (SIT) tests. Arena tests simulate a large open air blast, with lower explosive weights, by elongating the impulse of the blast wave. SIT tests are conducted to determine how the produced shock wave interacts and transfers its energy into a target object located at the end of the tunnel. The target used in this research is multilayered, with each layer being a different material. The targets are 2 ft. by 4 ft. (0.6096m by 1.2192m) pieces of Medium Density Fiberboard (MDF), DOW polystyrene foam insulation, and gypsum drywall. The order of these materials varies with each test. This shock tunnel is unique, because the geometry changes along its length. To fully understand how the shock waves are affected by these changes, a working model was needed. The second purpose of this model is to confirm the maximum charge size of 400 grams (14.11 oz.) of C4 that can be detonated inside the tunnel without causing damage to or failure of the tunnel, thus reducing the amount of time needed in downtime and repair. The model predicts pressures in various locations both within the tunnel and the attached target, thus assisting in determining where failures would likely occur. In the process of generating this model, several problems were encountered, including filling the tunnel with air, meshing the complex geometry, and creating the tunnel in a CAD system. This paper will discuss how these problems were solved. A working model was created by using ANSYS Explicit Dynamics and ANSYS Autodyn. The tunnel geometry file was created using SolidWorks and includes the complex geometry changes along with the target and its mount located at the end of the tunnel. The results produced by the model were compared to the field SIT tests. The comparison of the results from both the model and the experimental testing showed a similar trend in the pressure traces.

Jan 1, 2018

By Kirk Yeager

During the last several years the FBI has been involved with a detailed study of explosives designed to replicate formulations utilized world-wide by terrorists. In addition, numerous formulations , based on literature and internet sources were examined. During the early stages of this work, a good many of the energetic mixtures studied were based on simple ammonium nitrate fertilizer. While the use of ammonium nitrate in commercial explosives is well studied and documented, the characteristics of the mixtures produced by criminals and terrorists have been less well researched. To aid law-enforcement in understanding the properties of these poorly understood formulations, a “cradle to grave” examination of their characteristics was conducted.

Jan 1, 2001

By David Yanez

The hydroelectric project "El Cajón" is currently under construction in the state of Nayarit, on the Santiago River, in western Mexico. This project is comprised of a Concrete Face Rockfill Dam (CFRD) with a rockfill necessity of 10,5 million cubic meters and it reaches a height of 188 m. The generation equipment includes two turbines with a total installed capacity of 750 MW.

Jan 1, 2006

By Brian Lewis, Reinhold Daykin Schnell

Blasting specifications and guidelines are very important aspects of detailed project specifications covering any scope of work (SOW) that involves explosives and blasting procedures. A lot of larger construction or tunneling projects require some degree of project specifications for the entire scope of work on such project, including blasting specifications. It is important that all blasting specifications effectively and accurately address all explosives and blasting concerns associated with the SOW for such project. This includes safety and security, required personnel and their associated responsibilities, procedures and applications involving explosives, blast design and planning, blast monitoring and reporting, quality assurance and quality control, and local, state, and federal regulations and limitations. With the of wide range of information required in blasting and overall project specifications along with the risks associated with work involving explosives, it is also important to ensure qualified personnel are involved in interpreting or compiling and approving any blasting specifications and guidelines. The purpose of the following paper is to explore and present the basic information, as summarized above, that should be included and considered in the creation of detailed blasting specifications and guidelines. Detailed information is presented in specific relation to a potential bid package that would be compiled for a construction or tunneling project requiring protective or high-profile blasting.

Feb 6, 2023

By Joe Atalla, Jesse Desrochers, Rodrigo Hayashida, Joseph Mukendi Kabuya

The Mont-Wright mine stands as a prominent open-pit operation in Canada, renowned for its vast iron-ore reserves. However, the efficacy of its blasting operations, crucial for efficient production, has encountered challenges due to the diverse lithological compositions across multiple pits. This study presents a comprehensive approach to optimize blasting practices at Mont-Wright mine, tailored to the specific lithological characteristics of each rock domain. Through systematic analysis and experimentation, blasting guidelines were meticulously developed, aiming to enhance grindability and equipment productivity. The implementation of these guidelines promises significant improvements in operational efficiency and resource utilization, positioning Mont-Wright mine at the forefront of sustainable iron-ore extraction.

Jan 21, 2025

By Paul Miller, Rene Laprade

Does a 76 mm Ø hole drilled over 45 m deep remain straight? This is the question asked by the Engineering department at Placer Dome's Dome Mine in Timmins, Ontario before they could lay out the initiation sequence in a long-hole production stope. Everyone realized that the holes would wander over such great depths, but it was important to know where they went.

Jan 1, 1998

By Tom Short

The contract to drive twin 4,100 foot (1250.5m) long tunnels under the existing Cumberland Gap highway was awarded to a Joint Venture of S.A. Healy of Chicago, Illinois and Lodigiani USA of Fairfax, Virginia in January of 1991 under a $51.8 million bid. Due to very complex geological conditions, there were six distinct categories of excavation, the New Austrian Method of ground support was utilized throughout.

Jan 1, 1993

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020

By Kurt B. Oakes, Brian M. Fortelka

Unimin Corporation operates an underground Silica Sand mine at Guion, AR located in North Central Arkansas. The Silica Sand deposit at Guion is part of the St. Peter Sandstone Formation, which is overlain by a competent dolomitic limestone from the Joachim formation, acting as the roof directly above. Both the St. Peter and the Joachirn Formations are of Middle Ordovician age.

Jan 1, 1999

By Tyler Rockley, Greg Bailey

This paper is an engineering case study of a blast performed on a highly weathered sandstone isthmus in an area sensitive to vibration and airblast, the challenges associated with such a blast, the methods used to understand rock characteristics, the blast design considerations and a discussion of the blast results. The purpose of the blast was to remove approximately 12 feet (3.7 m) of surface material in order to install a pumping station. The isthmus provided several challenges due to the weathering of the rock and multiple open faces with surrounding water. The highly fractured and weathered rock was subject to about ten years of freeze thaw cycles, influx of water and seasonal submersion. As such, all actual rock conditions were indefinite, including fracturing, rock properties, degradation and competency. The isthmus also had immediate neighbors who were unused to the environmental effects of blasting. To help continue to keep the social license to operate in the area, it was important to reduce the ground vibration, blast duration, dust and airblast. These factors required a better understanding of how the rock would respond to blasting. In order to do this, test blasts were performed on the same geologic formation in a different location of the quarry that was less sensitive to vibration and airblast effects, allowing the blast parameters and design to be verified and refined. The test blasts were performed while monitoring vibration, air blast, material movement and overall shot performance, and the blasting parameters were adjusted accordingly. The isthmus blast was performed based on the final design from these test blasts. The drilling and loading of the shot all met acceptable criteria and were comparable to the test blasts. The blast performance, however, was not as expected; the depth impacted by the blast was substantially more than expected. Since the test blasts were performed in the same formation, but in material that was significantly less weathered than the isthmus, the actual effect of this weathering was the only difference between test blasting and the isthmus blast. Thus, these results can be used for future reference to highlight the effects of blasting such highly weathered rock and help instruct the blast design in similarly complex conditions.

By Francis Otuonye

Rock fragmentation by blasting still remains the most common and cost-effective method of excavating hard rock in mining and tunneling operations. During blasting, the dynamic stresses induced by the detonation of the explosive, in addition to fragmenting the rock in the vicinity of the blast, may fracture the rock at considerable distances from the point of detonation of the explosive. The fractures can result in reduced mine safety, increased costs to support the opening, low productivity and perhaps high ore dilution. Besides the dynamic stresses produced in the rock, air blast overpressure pulses are generated and propagate through the network of underground mine openings. The waves, unable to spread out spherically or hemispherically like blast waves from surface blasting, are forced to propagate by reflection from the roof, ribs and floor down the drift. Blast wave focusing can occur and produce intense shock waves that could damage ventilation barriers such as cement block stoppings.

Jan 1, 1992

By Jaco van den Berg, Dr. Todor Petrov, Dr. Josh Calnan, Dr. Jhon Silva

This paper shows and reviews the similitudes and differences in explosions generated by high explosives and gas explosions, the reasons why gas explosions are difficult to replicate using high explosives, and the considerations when performing explosive testing using methane gases and coal dust.

Feb 1, 2020

By Richard Mainiero, James H. Rowland III

For many years there have been small scale tests available for evaluating the toxic fumes production by capsensitive explosives (DOT Class 1. l), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agents in construction and mining, there is a need to determine the quantities of toxic ti,tmes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pet) tieI oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/set for the 1 to 10 pet range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4~mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding 5 and 10 pet aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

Jan 1, 2000

By Daniel Scott

Mines have used explosives for economical fragmentation for many years. It can therefore be expected that the mining industry has thoroughly researched how to achieve the most efficient blast. However, there is still a large amount of iteration that must be undertaken before blasting at a mine site can be refined enough to allow for consecutively successful blast results. And then the geology changes. This paper will present an approach to blast design that considers production goals, geology, budget, and safety, and will contrast the proposed method with well established blasting theory.

Jan 1, 2012

By Kevin Dunfield

The Deltadet System is composed of: The Deltadet II electronic Detonator. A Field Terminal to create, modify or simply execute an existing blasting sequence. The radio remote controlled option is composed of a Base Station to program, calibrate and initiate the EDDs plus a Blasting Box to send commands to the Base Station. Blasting lines to connect the EDDs to the Base Station (100m) and Visual Blast software to create or modify a blasting sequence.

Jan 1, 2004

By Lon Santis, Michael Swisdak, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc. (APT) have developed a quantitative risk assessment tool called IMESAFR (IME Safety Analysis for Risk) for managing risk from various activities undertaken in the commercial explosives industry. The first version was completed in 2006 and Version 2.0 of the software was completed in 2012, incorporating several major new features. The platform is now based on a Geographic Information System (GIS), providing a bird’s-eye-view to help visualize facility layouts and risk. Spatial data on potential explosion sites and exposed sites can now be automatically transferred from the images to ease users’ data input. Use of GIS data provides the ability to check facility compliance with quantity-distance (QD) standards such as the American Table of Distances (used by the Bureau of Alcohol, Tobacco, Firearms and Explosives, ATF), the NATO standard (used by Natural Resources Canada and other nations), or a user-defined table. Research conducted and knowledge gained over the last 10 years enabled changes in the algorithms and models that provide greater fidelity and reduce conservatism. Expert users can change global settings to more accurately match actual site conditions and the program runs using either Imperial (English) or SI (metric) units of measure. These changes and other new features are discussed and demonstrated.

Jan 1, 2013

By C A. "Hawk" Hanger

"The paper that will be presented is an in-depth study of sequential blasting using standardnon-electric shock tube down hole timing along with surface M.S. connector timing.Included also will be a discussion on the advantages in fragmentation, digability, oredilution' and ground vibration versus the common practice of row by row blasting. Alongwith the written presentation, several visual illustrations will be included. The visuals willrefine the actual direction and predicted movement of the shot involved."

Jan 1, 1993