Search Documents

By William Reisz

Over the years as surface mining operations have become more sophisticated, angle drilling has become a more popular blast design technique, especially in areas where overburden and stripping ratios have increased. Another method of blast design is the staggered pattern, which greatly improves explosives distribution within the blast. While both methods present some engineering challenges, this paper will discuss how the two methods can be combined to enhance fragmentation, improve cast percentage, drill production ratios and highwall control. A practical engineering approach will be presented as well as a discussion on the discipline required to maintain a quality blasting plan.

Jan 1, 2002

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

Since the ecrly 1970's several factcrs have changed. In the East the larger tracts of coal mined with large eauipment are being dePleted, The cost of moving the larger equipment from small tract to small tract becomes eccnomicallv unattractive, Conseauently, the tracts are being mined with smal!er draglines or with loader/truck haulage combination, This has resulted in a major increase in the cost of moving a cubic yard of overburden,

Jan 1, 1989

By William D. Hissem

While much technology has been developed and brought to bear in the area of blasting applications, the foundation work required for success in the muck pile begins with the drilling program.

Jan 1, 1997

By Jim Mikelait

Overview ?? Why do we need security? ?? Needs assessment ?? Elements to any security system ?? Protect, Detect, Alert, esponse ?? Electronic Security System Criteria ?? Advantages and Limitations of Various Security Options ?? Internal measures to protect against potentially harmful employees ?? How can technology improve my business?

Jan 1, 2006

By Michael Mann

Two house trailers and a modem modular house, all pillar-supported with cantilevered perimeters, were monitored for structural response to vibrations from surface coal mine blasts. Due to the large blast site distances, peak particle velocities measured in the ground beside the houses did not exceed 0.32 ips, and airblasts did not exceed 106 dB. However, the structures responded significantly to the ground vibrations, with maximum high-comer amplification factors as high as 8.5 in the horizontal directions. Vertical structural responses were as high as 10 times the vertical peak particle velocities in the ground, but appeared to be driven more by horizontal ground motions. No measurable airblast responses were observed. The natural frequencies of the structures ranged from 5 to 10 Hz.

Jan 1, 2000

By Braden T. Lusk, Rex A. Meyr, Kyle A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by MSHA and required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. A polycarbonate safe haven wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics to withstand the MSHA required 15 psi (103.4 kPa) blast loading spanning 200 milliseconds. The successful design was constructed in both half-scale and small scales in the University of Kentucky Explosives Research Team’s (UKERT) explosives driven shock tube. The constructed polycarbonate walls were tested multiple times to determine the walls resistance to blast pressure. The results for each test were analyzed and averaged to create one pressure versus time waveform which was then imported into the finite element program and modeled to compare deflections of each part to that was measured during testing for model validation. This paper summarizes the results.

Jan 1, 2014

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Neil T. Davie, Thomas K. Blanchat, Thomas C. Togami, Joe R. Weatherby, Dale S. Preece, Robert A. Benham, James J. Calderone

"Geotechnical structures ,such as underground bunkers, tunnels, and building foundations aresubjected to stress fields produced by..the gravity load on the structure and/or any overlyingstrata. These stress fields may be.. reproduced on a scaled model of the structure byproportionally increasing the gravity field through the use of a centrifuge. This technology canthen be used to assess the vulnerability of various geotechnical structures to explosive loading.Applications of this technology include assessing the effectiveness of earth penetrating weapons,evaluating the vulnerability of various structures, counter-terrorism, and model validation. Thisdocument describes the development of expertise in scale model explosive testing ongeotechnical structures using Sandia’s large scale centrifuge facility. This study focused onburied structures such as hardened storage bunkers or tunnels. Data from this study was used toevaluate the predictive capabilities oft existing hydrocodes and structural dynamics codesdeveloped at Sandia National Laboratories (such as Pronto/SPH, Pronto/CTH, and ALEGRA)."

Jan 1, 1998

By Neal Lee, Braden T. Lusk, Jhon Silva-Castro, Patrick J. Jenks

"Timing and charge sequence are very important for optimized blast design. Traditional nonelectricinitiation systems have moved the industry toward a system of delays consisting of hole-to-hole androw-to-row timing sequences that mimic the application of nonelectric surface delays or dual delayinitiator systems that have been prevalent in the blasting industry for many years. The increasedutilization of electronic detonators allows for the use of Regular Rhythmic Timing (RRT) utilizing onlyone delay between charges and a selected charge firing sequence. The hole to hole and row to row (HHRR) timing method has been utilized for blasting optimization and allows for simplistic changes to the tie in phase of the blasting sequence. When using this traditional timing methodology, for some specific cases related to the number holes and rows, crowding occurs in the delay between charges with subsequent increase in the peak particle velocity (PPV) produced by the blast. This is in contrast to RRT where the timing between the delays remains constant."

Jan 1, 2016

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By Bibhu Mohanty, Sheng Huang

Accurate measure of fragment size distribution is a key objective in all blasting and crushing operations. Several generic distribution functions have been devised to describe the degree of fragmentation for the representative range of fragments from selected measurements. The application of four distribution functions, i.e. Rosin-Rammler, Swebrec, Grady and Gilvarry, in describing fragment size distribution of impact-induced fragmentation of a limestone rock has been investigated. A modified Hopkinson Pressure Bar experimental set-up is used to control both impact velocity and energy input into the target rock. The feed size in the sample holder is varied from 6.35mm to 15.88mm in three ranges and the impact velocity up to 14m/s. The size distribution in the product is determined by sieve analysis for a range of impacts. The experimental results are fitted to the four distribution functions to examine their relative accuracy and reliability.

Jan 1, 2016

By Roberto Golchi

This article describes the method used to quantify the Environmental Impact for the mining, by drilling and blasting, of a borrow pit for a gravity-dam. The affected environment was broken down into a number of components, such as public health and safety, social relationship, air and water quality, flora and fauna. The effect of the various impacting factors from the mining activities, both directly and indirectly, was then calculated for each environmental component. To do this, each impacting factor was first given a magnitude, a number based solely on the range of scenarios possible for the impacting factor. A matrix of weighting factors was then derived to systematically quantify, and normalise, the effects of each impacting factor on each environmental component. The overall impact upon each individual environmental component was then calculated by summing the weighted magnitudes for all the impacting factors.

Jan 1, 2003

By Christopher Cloete Uys, Luis Manuel Poinha Valentim

The purpose of this workshop is to describe and demonstrate the use of SPEEDWAVE, a high speed data recorder, its VOD enhancements, and the software which binds the system together. The system was designed by TLC Sohware, SOUTH AFRICA. TLC is a company spedalising in the solution of engineering problems, using computertechnology as a base. TLC was founded in 1987, and has since been involved in many different.measurement, control, simulation and modelling projects. Wth respect to the blasting industry, TLC has, in conjunction with AECI South Africa/ICI, developed a tunnel mining design aid, a ring blasting design aid, a multkhannel seismograph and a laser surveying program. In 1989, TLC designed and built the BA800. a microcomputer-based high speed recorder. These recorders are still in use and are producing valuable results. Based on improved technology and with the field experience of the BA800, TLC has designed and developed the data recorder SPEEDWWE.

Jan 1, 1995

By Qian (Ken) Liu, Remi Proulx

A large scale blast damage project was carried out over the past two years at INCO Ltd Manitoba Division co-funded by the Canada/Manitoba Mineral Development Agreement. The experiment was conducted at the T-3 Mine in two mining stopes with an experimental drift developed in the hanging-wall for the installation of monitoring instrumentation. The objective was to observe and subsequently to reduce ore dilution by monitoring the performance of blasts, the hanging wall movement, as well as the cavity of the open stopes.

Jan 1, 1995

By H Ulrich Leiste, Leslie Talor

This paper describes a series of small scale tests conducted to investigate the loading applied to a flat plate by the detonation of a cylindrical charge very close (between two and three charge radii from the center of the charge) to the structure. The testing used very small quantities of explosive (PETN): Two different series of tests were conducted. In the first test series, impulse loading on the target plate was investigated using three different sizes of charge. In the second series, pressure time profiles were determined. The charge size was 6 g or less. Impulse was found using high speed video of the target plate to determine its displacement as a function of time, from which initial plate velocity was obtained. Kolsky Bars, placed at the same distance from the charge as the target plate, were used to determine the free-field pressure time profile of the output of the charge at this distance. Two different types of target plates were used in the impulse study. One was just a plate while the other was a plate constrained with a steel frame.

Jan 1, 2009

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016