Search Documents

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Hector O. Romero, Paulo C. Fernández A, Claudio C. Gajardo

Phase 06 of the Los Bronces mine, currently under extraction for development, has the particularity of being close to the installations and buildings of a neighboring copper mine. Therefore, the blasts must ensure the continuity of the operation without affecting the nearby structures of the neighboring district, which include Maintenance sheds and Warehouse. Specifically, the safeguards consider a scenario that includes: - Flyrock projections (<150m) - Edge profile studies - Vibrations according to the NCh3577 standard - Nitrous gases Additionally, Phase 06 is also within Los Bronces, so strict control over spillage into the pit is necessary to avoid blocking ramp access to this level. The challenge lies in protecting not only the operation and facilities of the neighboring mining district but also the operability of Los Bronces. Thus, addressing these considerations, blasting configurations are developed with prior simulation of vibration models, flyrock, and spillage in all blasts, with strict control of technical design and implementation to ensure the results. Currently, blasts are successfully executed with control of projections based on the proximity of the projects, vibration (<40mm/s) with decoupling of holes of 17 mm/s between holes, reactive rock tests for explosive selection (loading advancement), and spillage simulation inside the pit according to the loading design; thus, ensuring operational continuity and mine development.

Jan 21, 2025

By Sharon K. Reamer, Klaus G. Hinzen

A series of controlled seismic experiments was performed in a limestone quarry in southern Germany to study seismic effects of cylindrical charges fired in both a half space (HS) (burden 63 m) and quarter space (QS) (burdens of 3 and 3.5 m) geometry. Charge columns contained from 20-32 kg of explosives and initiated from the bottom. The explosives formed a cylinder 4 m (20 kg) and 5 m (32 kg) high and 90 mm in diameter at depths from 3-8 m below ground level. Prior to each of the larger explosions, small charges of 0.12 kg seismogelit were fired at 4 m and 8 m depths in the same boreholes. Seismograms were obtained from 23 three component surface stations and up to 10 three component borehole stations (6 m depth). For each experiment, stations were located on three linear profiles of length 72 m at different azimuths from the source and one semicircular profile at a constant range of 30 m.

Jan 1, 1991

By N Gkikizas-Lampropoulis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper interprets previous experimental information on the effect of delay on fragmentation with the aid of some new experimental observations of the time of detachment of the free face of the blast as well as results of numerical modelling. It was shown that detachment of the burden occurs at delays shorter than the one which produced optimum fragmentation in the experiments, suggesting some fragmentation improvement due to gas action. In addition, at the spacing to burden ratio of the experiments, the damage zone from an earlier detonating charge extends the distance to the neighboring charge, essentially affecting the burden of some of the holes of the blast, at detonation time. Computer modelling demonstrated that increased spacing results is less overlap of stress induced damage zones meaning that there is less influence of delay on stress wave induced fragmentation. It was also shown that simultaneous initiation results in less back break, while increased back break may result even with short delay times.

Jan 1, 2016

By Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes(CO + NO2) clearance and workplace re-entry time have overlooked the effects of toxic gases entrapped in the muckpile. The currently available models forcalculatingthe mine re-entry times assume that all post-blast fumes are emitted upon detonation. However,recentstudies reportedthat as much as 60% to 70% of the fumes or gases produced during an underground development blasting couldremain entrapped in the adjacent rock mass or in the muckpile. Entrapped fumes are slowly released,and when disturbed, high concentrations are released, representing a possible risk during the digging and transportation of the muckpile. This study uses CFD, SC-Flow software to understandthe behaviorof the entrapped fumes and theireffect on mine re-entry time.

Feb 1, 2020

By Amos Bryant, Jesse Davis

This paper compares the predictions of the latest Institute of Makers of Explosives Safety Analysis for Risk (IMESAFR) model versus physical test data recovered from ISO-1 and ISO-2 tests in Woomera, SA. ISO-1 testing included placing 1054 kg (2324 lbs) of ANFO (ammonium nitrate-fuel oil) inside an ISO container on a flat bed truck. ISO-2 testing was identical except the NEW was 4000 kg (8818 lbs). The IMESAFR predictions are based on model runs using the best match available to the actual donor type involved in the test. This type of debris analysis is not the standard output of IMESAFR, as the program is designed to assess the probability of human fatality. However, all of the IMESAFR predictions presented were obtained from the use of the actual model equations and algorithms without adjustment. Test results from ISO-1 and ISO-2 will be presented as well as findings from the comparison between model results and actual explosive results from the ISO testing efforts.

Jan 1, 2010

By Robert Hopler

After the disbanding of the Gunpowder Trust Association in 1904, the Association of Independent Powder and Dynamite Manufacturers was formed, followed in May of 1906 by the formation of the Association of Manufacturers of Powder and High Explosives. Due to a lack of success in attracting all manufacturers to membership, these organizations did not survive.

Jan 1, 2014

By John Norman

This paper will cover blasting techniques that are applicable to underground and other rescue that involves removing obstacles and breaking rock in close proximity to rescuers and subjects.

Feb 1, 2020

By Ayman Tawadrous

Cave mining offers a flexible technique to exploit large, low grade, deep ore bodies with low operating costs. It is typically done in either a top down approach; i.e. sublevel caving, or in a bottom up approach; i.e. block or panel caving, to extract ore bodies that may have been previously considered unfeasible to mine. Sublevel Cave (SLC) mining, in particular, is a cave mining method based upon the utilization of gravity of blasted ore while the overlying host rock fractures and caves under induced stresses and gravity. Thereby the caved waste originating from the overlying rock mass fills the temporary void created by ore extraction to achieve a controlled collapse of the roof.

Jan 1, 2015

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Robert Hopler

A detonator is a copper tube about a quarter of an inch in diameter and an inch and a half long, closed at one end and containing in the closed end a small charge of fulminate of mercury, which has been found to be the best explosive for detonating dynamite. The fulminate charge is a very powerful explosive very sensitive to friction, lows or heat and very poisonous. When exploded it has an intense local action, shattering things in its immediate vicinity, but not extending very far away from the explosion. This kind of detonator is intended to be exploded by a spark from burning fuse.

Jan 1, 2014

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By Jihan Farhan Lubis, Putu Chandra Darmansyah

Ground vibration caused by blasting has become a common concern, especially when blasting is conducted near buildings or structures. Uncontrolled vibrations can potentially damage nearby infrastructure if appropriate control measures are not implemented. PT Tambang Semen SUKABUMI, a limestone mining company, is planning to carry out blasting activities near a crusher building located approximately 80 meters away. This building is classified as a Class 5 structure, with a maximum allowable Peak Particle Velocity (PPV) of 40 mm/s, in accordance with the Indonesian national standard SNI 7571:2023. To ensure compliance with this limit, a Signature Holes Analysis (SHA) was conducted using the Hanwha HEBS II electronic detonator initiation system. This analysis measured ground vibration from single-hole blasts, with the average vibration from three SHA holes recorded at 49 mm/s. A site constant analysis using the scaled distance formula yielded a multiple R value of 0.87. However, the ANOVA table showed a significance-F value of 0.24, which is greater than 0.05 indicating that the regression model used for prediction was not statistically significant. Using the SHA data and assuming a maximum of 30 blast holes, a recommended delay timing of 22 × 15 milliseconds was selected. This produced a predicted PPV of 17.25 mm/s. The comparison between predicted and actual PPV values demonstrates that the delay configuration derived from Signature Hole Analysis provides reliable results. The observed deviations range from -16% to +29%, with an average deviation of only 8%, indicating a high level of accuracy and consistency. Using the actual blast data, three model prediction were applied for predicting the most accurate prediction that close to the actual value. The SHA method, utilizing actual single-hole vibration measurements and optimized delay timing, provided the lowest average deviation of ±8% and the smallest absolute error (2.45 mm/s) from actual measurements, demonstrating high reliability for sites with sufficient signature data. Meanwhile, the log-log regression model yielded the highest coefficient of determination (R² = 0.751) and the smallest prediction deviation (3%) when standard deviation margins were considered, making it highly effective for predictive modeling.

Jan 26, 2026

By R. Hazael, R. Alford, R. Critchley

The ability to compare explosives is fundamental. Numerous methods are used and while simple conversion factors are often used, the use of TNT Equivalency (TNTe) is not a simple subject as explosives exhibit very different equivalencies depending on whether the pressure or impulse are being considered as well as other conditions. The scaled distance has been found to have a significant effect on the TNTe but due to the difficulty of taking measurements at very close ranges, no TNTe have been quoted for charges in direct contact (Z=0). This paper describes the use of a ballistic pendulum to measure the impulse from contact charges and presents some surprising results that require a two-stage propulsion, as originally described by Backofen, to be explained.

Jan 1, 2024

By Martin Langenderfer, Catherine Johnson, Phillip Mulligan, Kelly Williams

The physical geometry of a charge has a direct correlation to the geometry of the shock wave. This relationship appears strongest within the boundaries of the visible fireball. As the shock wave propagates outward past the limits of the fireball, the theory states that the geometry of the shock wave should even out and become more spherical. This paper investigates pressure vs. time at two distances, one ‘Near Field’ at the extent of the fireball and one ‘Far Field.' The two Fields were instrumented with three free-Field pressure probes from PCB oriented at 0, 45, and 90 degrees to the front face of the charge, in the same horizontal plane as the charge. This orientation allows for the comparison of the shock wave from the face and vertices of the charge. All the pressure sensors were connected to a Data Acquisition System (DAS) recording at 2 million samples per second (2MS/s). Two high-speed cameras, a Phantom and an MREL Ranger II, recorded the detonations for qualitative examination of the fireball, and the shock wave. Three charge geometries were used and compared to the shock propagation of a sphere. The other geometries tested are cylinders, cubes, and tetrahedrons. Charges were made from a PETN based sheet explosive. In the Near Field, a lower pressure is observed along charge vertices with highest pressures from each face. In the Far Field, vertices record a higher pressure, possibly due to the shock waves from the adjacent faces intersecting, indicating that shock pressures do not always even out in the Far Field. This paper will describe the methodology and findings of this experiment and attempt to determine causality for trends in the data gathered.

Jan 1, 2018

By Alyse Munro Hindley

The increasing negative public opinion toward blasting has led to stricter regulations and increased costs. This paper outlines alternative methods of rock excavation and the safety regulations and certification required by blasting professionals. Most importantly, however, it showcases the benefits and accomplishments that controlled blasting bring to society, giving the public a better understanding of the necessity of blasting in modern society.

Jan 1, 2015

By DuPont Magazine

RBH Note: as stated many times in these articles, frozen dynamite was one of the greatest hazards facing the blaster. It wasn’t until the late 1920s that it was solved for good, with the introduction of nitrated ethylene glycol as a partial replacement for nitroglycerin in dynamites. The du Pont low freezing dynamites contained TNT, DNT, or nitro-substitution compounds of various sorts.

Jan 1, 2015

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By Iván Aguirre Palacios, Jean Guiroux Toro, Eduardo Valdés Guerra

Currently, mining operations seek to be competitive in the market. To achieve this, one of the relevant factors is to maintain and improve the productivity of the extractive processes, mainly the loading from the point of opening of the mineral bodies. To do this, many techniques suggest reducing production costs, with the first opening of your free-face up raises. However, there are different ways to carry out these open-face raises up opening processes, where the balance of costs and construction time must be well planned to meet production plans. Operationally, there are different techniques for its construction, the most common being Blind-Hole up Raises and those with drilling with current production equipment that operates mining operations. This study shows a methodology and the results of the implementation of access stack drilling with production drilling rigs for a maximum height of 15 m with electronic detonators in production blasting. Within the methodology used, Qa/Qc processes were considered in cargoes with explosives, instrumentation for monitoring (vibrations), VOD registration, among others. As a result, of a total of 12 raises up blasts, construction time was reduced by 45% and the cost of drilling and blasting (P&V) was reduced by 50%, for up raises with a maximum height of 15 meters. Regarding the efficiency of the heights, this was 97% compared to the planned drilling design.

Jan 26, 2026

By Kain Petterson, P D. Katsabanis

Blast fragmentation, determined using image analysis was correlated to drill monitoring parameters in an open pit operation. Average fragment size and 80% passing size showed strong correlation with specific energy of drilling as well as with torque, while the same passing sizes did not correlate well with the rate of penetration. It was also determined that the uniformity of fragmentation decreases with the specific energy of drilling. Thus drilling monitoring parameters appear to be valuable in determining the blastability of the rock mass, enabling adjustment of blast loading to respond to changing conditions in the rock mass.

Jan 1, 2013