Search Documents

By R. Reed Skaggs, William Gault, Douglas Kooker

Both armored personnel carriers and light combat vehicles are increasingly vulnerable to a variety of highly lethal antitank land mines. As a result, there is a need for modeling and understanding the interaction of mine blast products with respect to the resulting loading and damage mechanisms inflicted by explosive blast and impact on vehicle structures. However, the mechanics of blast soil interactions are still poorly understood. The objective of this investigation is to computationally simulate a series of experimental buried mine explosions in saturated sand soil -- over a wide range of scale – and compare the predictions of blast loading to data. Small scale tests have recently been conducted at the University of Maryland with a few grams of RDX acting against an aluminum plate, while recent full-scale tests at ARL involve several kilograms of TNT against 12,500 kg of RHA. The ARL measurements reported here are based on the Vertical Impulse Measurement Fixture (VIMF) facility, a structural mechanical device that responds to blast loading by measuring the vertical displacement of a fixed mass vertical guide rail, which is a direct measure of the imparted impulse. CTH predictions for vertical momentum of the target plate are within 60 – 80 % of the reported impulse data for this wide ranging set of tests. One of the comparisons, however, suggests that the TNT charge in a particular VIMF test may not have fully reacted.

Jan 1, 2005

Blast vibration analysis under relatively near-field conditions has been carried out in a narrow-vein underground operation. The objective was to characterize the vibration signal (particle acceleration and velocity) from carefully controlled stope blasts. The limitations of such analysis in deriving design guidelines for reducing dilution has been elucidated. It has been shown that identification of each individual hole with specific explosive types can yield explosive-specific predictive equations for particle velocity. This has been coupled with measurement of actual overbreak to arrive at a limiting vibration level to generate a realistic design tool for controlling dilution in narrow-vein mines.

Jan 1, 2003

By Robert Hopler

It is the nature of the initial detonation to the powder around the cap which governs the greater or less effect of the explosion of the whole charge. The cap communicates to the first particles of powder a disruptive impulse, which, according to the nature and strength of the cap, more or less completely overthrows their equilibrium and decomposes the powder with great energy, setting up sympathetic vibrations that explode the particles of powder in turn by the violent disturbances or friction between them in a regular succession of impulses and decompositions, which, if started with sufficient energy, are of such intense heat and velocity that the rupturing force of the explosive is developed practically instantaneously. This detonation has already been shown to be not only the result of mechanical force, but a combination of extremely sudden chemical and dynamical reactions which set up vibrations to which different powders are more or less susceptible, and these explosive reactions will be propagated through the mass of the powder according to the intensity of the vibrations and the resistance with which their motion is opposed by the nature and consistency of the powder, whether it be difficult or easy to oxidize, soft and plastic like dynamite, or hard. If the initial detonation of the powder surrounding the cap is of the highest degree, the vibrations will be most intense and will be propagated further through the mass than by a poorer detonation. Hence the different degrees of detonation. Unless the first particles of powder are so thoroughly decomposed by a detonation of high order, or first degree, as to convey the necessary heat and energy to detonate the whole charge, the greatest force of the powder will not be developed. There will frequently be unbottomed holes or pieces of unexploded powder scattered about, or both, and the air in the mine will be contaminated with some obnoxious gases that have not been completely oxidized.

Jan 1, 2007

By Victor C. Bryan

One of the most sought after answers in any consideration of blasting activities relative to mines and quarries is how to safely and efficiently use explosives. While that discussion might be relatively straightfonvard in a “site specific” situation. it becomes more complex when viewed from a broad geographic perspective. Such is the case in considering the operations of one United States producer of crushed stone with surface and underground mines spread over a thirteen state area. Differing geologic environments set conditions that dictate to the blaster as now specifically to get optimum results from the blast hole. This treatise is a discussion of the various methods, materials, and principles used in conducting such blasting operations.

Jan 1, 1991

By Fumihiko Sumiya, Shinya Tanaka, Yukio Kato, Kenji Tanaka, Tetsuya Sawada

When explosives are heated under an acidic environment due to metal sulfide and sulfuric acidity, their decomposition temperature falls remarkably and decomposition reaction occurs quickly, and then explosives have the risk of the deflagration to the detonation transition. Heat resistant commercial explosives which can be used under conditions of high temperature of 200ºC and an acidic environment were studied. We developed the explosive composition consisted of ammonium perchlorate (AP) as oxidizer, saturated hydrocarbon oil as fuel and binder, and calcium carbonate as decomposition inhibitor. The characteristics of this explosive composition show a heat resistance over 24 hours at 200ºC, and a detonation velocity over 2,500 m s-1. This explosive composition has a cap-sensitivity at temperature higher than 100ºC. Cost effective heat resistant commercial explosives were created by the optimization of the grain size of AP as a main component, the addition of saturated hydrocarbon oil and calcium carbonate, and the control of bulk density by the addition of micro-balloons.

Jan 1, 2003

By X Meng, W. A. Hustrulid, M. K. McCarter

Rock excavation in both surface and underground mining is largely accomplished using the drill and blast technique. At the perimeter of such excavations, cautious blasting procedures are often employed to minimize unwanted damage to the remaining rock. Of the several different techniques available, the use of explosive charges with a diameter smaller than the holes in which they are introduced (so-called decoupled charges) is the most common. In spite of the long and widespread use of the technique, a technically sound basis for relating the borehole wall pressure to the explosion pressure is still lacking. Such a relationship is required for optimal design

Jan 1, 2005

By Mark Svinkin

The purpose of this paper is to present an overview of recommended existing criteria of ground vibrations generated by blasting. It is shown that these criteria have limited liability because they were found for specific categories of structures. A new approach based on measurement of structure vibrations is suggested for assessment of damage in structures subjected to blasting vibrations. This approach provides the flexibility of implicitly considering a variety of soil-structure interaction and structure conditions. It is explained a new frequency-independent safe-level criterion of 51 mm/s (2 in/s) for the PPV of structural vibrations. Attention is brought to use seismographs properly calibrated for the required frequency range. Positive flexibility is demonstrated in assessment of structure and component of concern vibrations from blasting.

Jan 1, 2003

By Steve Colburn

The new CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, new Windows-based interactive software program, which can be run on any standard PC.

Jan 1, 1995

By Ann Barron

“Hurry up” is the latest battle cry at explosives companies struggling to stay in compliance with the ever-growing onslaught of government regulations. The pressure continues to mount on industry professionals who face stiff penalties if their companies fail to comply with the law. Such penalties can range from monetary fines and revocation of blasting permits and licenses, to increased liability for civil claims or even criminal charges.

Jan 1, 2006

By R. Singh, M. Roy, D. Singh

Success of a blasting pattern in Blasting-off-the-solid (BOS) in Bord (Room) & Pillar method of coal mining is judged by the percentage of pull achieved vis-à-vis the yield of coal produced in a blasted round. Improper blast design and distribution of explosives in shot holes normally causes poor breakage i.e. a major portion of shot holes left unbroken resulting into reduced yield per blast. Over and above the disturbance to the roof is also due to excessive vibration caused by explosive energy not properly utilized in fragmentation.

Jan 1, 2003

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By G K. Jorkenson

The SABREX Blast Modelling Program was developed joinlly by the companies of the ICI Explosives Group. of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.

Jan 1, 1989

By Bruce Vandenberg, R F. Chiappetta

"The High Speed 2D Analysis program allows the user to bring in data from several different sources. Of course, keyboard entry is included as a source. Other data is inputted through the serial port (X-2321 of the PC. Two types of data are transferred via the serial port. The first is the tablet digitizer data. The three types supported presently are the GTCO, tablet digitizers. and the Calcomp 2500 and 9100 series To transfer digitized data turn on the selected digitizer and place the cursor on the tablet. Enter the High Speed pmg.ram and select from the Input Program menu the Digitize Inputs(20) option and follow the instructions. TO exit the session, either a keyboard entry or a cursor button is pressed. The second type of serial port input Is from the collectors of the listed survey systems. Typically a file transfer program will be used to send the data from the collector to the PC. This topic will not be addressed at this time."

Jan 1, 1989

By A. K. Mishra

The mineral industry is leading towards a technology driven optimization process. Drilling and blasting are such unit operations in a mine, which can alter the balance sheet of the mine if not planned properly. The development, improvement and utilisation of innovative technologies in terms of blast monitoring instruments and explosives technology are important for cost effectiveness and safety of mineral industries. The ever-growing demand of mineral has compelled the industry to adopt mega opencast projects with big equipments. This has necessitated use of few hundred tonnes of explosives in each blast. The bulk delivered fourth generation explosives has solved the problem of explosive loading to a large extent. The priming of bulk delivered explosives in Indian mines uses the conventional PETN/TNT based cast boosters. As the conventional cast booster possess safety problems in terms of handling and use, so Indian Explosives Ltd., has developed an emulsion based cast booster (Powergel Boost).

Jan 1, 2005

By Chen Jianping, Wu Li, Wei Banyun, Chen Canchang

Liquified petroleum gas mixed with oxygen has been used as a new type of mixed gas source for gas detonating system. The experimental studies have been done on the detonation feature of gas detonating transmission in a long and thin tube, the transmitting reliability for detonating network, the design on gas exploder and test devices. The results of the study show that (1 )Liquified petroleum mixed with oxygen can be used as a new type of regular gas source. (2)The transmission of detonating wave is reliable for new type of mixed gas in a 500-meter long plastic tube with 3mm inner diameter and the detonating velocity is up to 2500m/s. The detonating wave can surely initiate and transmit several branched gas detonating cap and explosive through the end of detonating network, the tubes inner diameter for the detonating quenching is 0. I’mm. (3)The gas exploder designed by authors can be used for gas propotional distribution,strong turbulence-mixing,initiating by reflex shock wave and safety control purposes. The developed double flowmeter can be used together or seperately in responsible for main testing in the system.

Jan 1, 1999

By Dong-Hyun Kim Kim, Tai-Ro Lee, Young-Hwa Seo

Overbreak occurred inevitably in a tunnel excavation, is the main factor for increasing cost and period in tunnel projects. Furthermore the damage to the remaining rock mass related to the overbreak can give rise to a serious safety problem in tunnels. As a rule of thumb, causes for the overbreak are inaccuracy in drilling, the wrong design of blasting and selection of explosives, and heterogeneity in rock mass. Specially, the geological features of the rock mass around the periphery of an excavation are very important factors, so a lot of research has been conducted to describe this phenomena. But the geological rockmass classification for the overbreak and the method for decreasing the overbreak have not been fully established. Besides, the technical improvement of the charge method is needed as explosives for the smooth blasting have not functioned efficiently. In this study, the working face around periphery of an excavation has been continuously sectionalized to 5~ 6 parts, and the new Blastability Index for the overbreak based on 6 factors of RMD(Rock Mass Description), UCS(Uniaxial Compressive Strength) JPS(Joint Plane Spacing), JPO(Joint Plane Orientation), JPA(Joint Plane Aperture) and FM(Filling Material) is proposed to classify sections of the working face. On the basis of this classification, the distance between contour holes and the charging density are determined to minimize the overbreak. For controlling the charging density and improving the function of explosives, the New Deck Charge(N.D.C) method utilizing the deck charge effect and detonation transmission in hole has been developed.

Jan 1, 2003

By Ivan Carrasco, Benjamin Cebrian

Mining companies have traditionally organized their structure around a scheme easy to manage: Mining Department and Mill Department. In a challenging landscape for mining, with decreasing grades, increasing rock hardness and more expensive energy, this way to organize departments has resulted in internal disputes and often contradictory targets between both mine and mill. These compete for individual, separated budgets whose Key Performance Indexes often damage each other’s output. The results are increased total production costs and reduction of profits. Some companies have completed the first step in eliminating these inefficiencies by creating Fragmentation Engineers and Fragmentation Superintendents. With all the knowledge available on the overall fragmentation process and costs, in this document an overhaul of the traditional management structure is proposed. Is a step further Mine-to-mill and mine-to-leach programs. Since comminution is the most expensive step of the mineral exploitation, it should be taken as a whole, not divided into competing departments. Thus, mining departments should be re-grouped into: transportation, fragmentation and flotation.

Jan 1, 2014

By Karl E. Burgher

Since World War II, the need for the use of explosives with testing, construction, demolition, mining and quarrying near urban areas has increased dramatically. Once remote, testing areas have been encroached upon by commercial and residential areas. Evidence has been found that overpressure levels near these areas can be estimated using meteorological conditions. This paper reviews a study where 205 test shots were fired, meteorological conditions recorded, and over-pressure levels estimated using multiple regression techniques.

Jan 1, 1988

By Dale S. Preece

The blast-induced movement and final location of geologic layers that may cause environmental problems can be predicted using discrete element methods. This prediction capability can be used by mine operators to locate the material in the muck pile during excavation which would allow encapsulation to prevent groundwater infiltration.

Jan 1, 1994

By Harry Verakis, Thomas Lobb

In the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry and coal mining was the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past two decades. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. This paper is a summary and an update of the surface mine blasting accident investigations and studies conducted previously by the Mine Safety and Health Administration (MSHA) and the former U.S. Bureau of Mines.

Jan 1, 2001