Search Documents

By Michael D. McGill

The effect of fragmentation size distribution as it relates to front end loader productivity was evaluated by comparing loader cycle times to fragmentation size of the shot rock. At Gold Mine in Southern Utah, a gold deposit containing both limestone and sandstone formations were blasted in the same shot.

Jan 1, 1994

By Shazad Hosein, William Birch, Douglas A. Anderson

This paper will present the results of tests of a new method for assessing explosive performance using wavelet transform analysis of standard blast seismograms. The theoretical background of the method was presented at an earlier ISEE conference.

Jan 1, 2015

By Kenneth Eltschlager, Jim Ratcliff, Michael Mann, Edward Sheehan

The Appalachian Blaster Certification Delegation initiated a study to compare the consistency of measurements from blasting seismographs. Six blasts were monitored at surface coal mines in West Virginia, Maryland, and Ohio. A total of seven different makes were deployed during the tests, with as many as seven models from five different manufacturers compared during any one blast. Great care was taken to bury the geophones in identical fashion. The variations in seismograph readings were compared to the International Society of Explosives Engineers’ Performance Specifications for Blasting Seismographs. Between 4 and 125 Hertz, the ground vibration amplitudes should be within ±5% and airblast amplitudes should be ±1 decibel. For each of the three mutually perpendicular ground vibration channels and the acoustic channel, the median value of all the units was used as a baseline for comparison. The six blasts monitored had median peak particle velocities ranging from 0.42 to 3.47 inches per second (in/s) (10.7 – 88.1 mm/s) and median airblasts ranging from 124 to 135 decibels (dB). There were 46 seismograph recordings for the six blasts. Eighteen (39%) of the 46 maximum peak particle velocities varied more than ±5% from the median. A total of 138 (3 × 46) component particle velocities were recorded, with 50 (36%) of the readings varying more than ±5% from the median. For airblast comparison, 43 recordings were obtained, with seven (16%) varying more than ±1 dB of the median. Variances may be attributable to blasting seismograph differences, variations in field deployment, and relative locations of the geophones. Full waveform seismic and acoustic overlays for individual blasts showed encouraging conformity with some slight anomalies

Jan 1, 2015

By Will Hunt, Darren Thornton

In March of 2013, an undisclosed gold mine (MINE X), located in the Western United States, performed blast movement monitoring of three blasts occurring in one of two active pits. Blast Movement Monitors (BMMs) were placed in the bench before blasting, and located after the blast to determine vectors of movement. Using blast movement software, ore/waste boundaries were translated. These locations were compared to MINE X’s standard ore translation procedure, which consisted of moving polygon boundaries by 17.5 feet (5.3 m) in the burden direction of the blast hole pattern. This translation amount, identified by MINE X as “average” motion, had been ascertained by performing a previous blast movement study.

Jan 1, 2014

By Kevin Landey, Eric Gerst

Expanding blast patterns to near the limit of an explosives’ ability to do the necessary amount of work is a common practice to reduce drilling and blasting costs. Choosing less expensive explosives such as ANFO vs. emulsion, bulk product versus packaged product, etc. are also common cost savers. Both practices are only effective as long as the pattern geometries are accurately drilled. However, will pushing the limits on pattern sizes and explosive products produce consistent results at the face, minimize oversize, produce superior fragmentation, and improve crusher throughput? Sometimes, but no amount of explosives can overcome a poorly drilled pattern. Knowing the probable outcome of any changes in drilling and blasting is valuable in achieving success.

Jan 1, 2018

By Brandon Fryman, Josh Hoffman, Rhys Baker

A post-detonation debris collection project was led in conjunction with a large ammonium nitrate(AN) railcar detonation conducted by the Department of Homeland Security-Transportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in a Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about the effects and consequences following an AN detonation. The test took place at the Utah Dugway Proving Grounds on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. A paper was presented at the 2019 ISEE Conference on the collection efforts, challenges, and lessons learned. A complete data analysis effort was completed on the test data in 2019 that resulted in updates to the QRA Railcar Potential Explosion Site (PES)model and AN engine. The analysis included an assessment of the debris data resulting from the Derailed test. This paper is meant to serve as a summary of the analysis effort and findings and as an update to the previously presented lessons learned from the debris collection and analysis effort.

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

By John Babcock, Bryan C. Smith

In a partnership between Luck Stone Corporation and Loudoun Water, a 42” (1.067m) steel pipeline was constructed along the perimeter of an extensive permitted reserve of diabase rock Luck Stone was about to begin mining. Loudoun Water provides drinking water and wastewater services to over 75,000 households in Loudoun County, Virginia. In discussions to establish the 30-foot (9.1 meter) easement for Loudoun Water within the permitted reserve of diabase rock, Luck Stone and Loudoun Water agreed on the following basic conditions: • Luck Stone could execute production blasting as close to the easement as physical conditions of overburden depth permits. We estimated the minimum distance to be about 75-feet (22.86 meters) from the centerline of the pipe. • Loudoun Water would install strain gauges on the pipe every 500-feet (152.4 m) along the entire length of the future reserve area. This resulted in the installation of 18 strain gauges. • Luck Stone would contract a third-party vibration monitoring company, agreed to by Loudoun Water, to monitor the strain gauges and provide seismograph reading at appropriate locations along the pipe as mining progresses. All information would be provided to Loudoun Water. • Luck Stone’s blasting will be conducted in a manner that ensures the recommended strains are not exceeded.

Jan 1, 2019

By Marwan M. Mohammed, Hani S. Mitri, Wilfrid Comeaul, Baoyao Tang

In many parts of the world, rockbursts have become a major problem of mining at depth. As orebodies are being mined deeper, rockburst phenomena have become familiar to deep hard rock mines. Rockbursts are generally characterised by sudden release of energy in a volume of highly stressed rock, which can cause local violent failure of the rock mass around the opening. One method of controlling these failures is to precondition the rock mass by detonating fully confined explosive charges at the appropriate locations. This method known as destress blasting, was first tried in the deep South African gold mines (Roux et al., 1957), and was widely used later in Canada, United States, France, Poland and Japan.

Jan 1, 1999

By R Castedo, L. M. Lopez, J. A. Sanchidrian

In 2014 the authors presented results from 13 tests made with two blasting seismographs on a vibration exciter. They measured coupling transmissibility as function of frequency (i.e. ratio of the velocity of the sensor mount to the velocity of the ground motion) from 16 to 200 Hz at one or two vibrations levels (5 mm/s or 0.2 in/s, and 20 mm/s or 0.79 in/s) with mounts freely placed, sandbagged, and anchored to a granite slab firmly attached to the plate of a vibration exciter. As the memory capacity of one of the seismographs prevented to cover low frequencies, e.g. 4-16 Hz, a new measuring campaign has been recently made to extend the study down to 2 Hz. In this campaign, two more techniques, in which the sensor mounts were fixed with thermal adhesive or a combination of duct tape and gypsum plaster, have been also investigated from 2 to 200 Hz at 5 and 20 mm/s. Free and sandbagged mounts lead to a weak coupling of the mounts to rock, so that transmissibility depends on the characteristics of the imposed rock motion (peak velocity and frequency). Measurements are accurate only at low frequencies (below 17 Hz for free mounts and 10 Hz for sandbagged) in the tested conditions (velocities up to 20 mm/s). Above these frequencies, ground motion in the measurement can be modified by a factor of 0.16 to 1.22. Anchored, glued and plastered mounts achieve a stiff rock-to-ground coupling, ensuring consistent measurements for the frequencies commonly found in blasting independently of the vibration level and the mount characteristics

Jan 1, 2015

By Per-Anders Persson

This chapter deals with the concepts ofshock waves aud detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mrc!~amcal work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1994

By Bruce B. Redpath, Doug Crice, Rob Huggins

Over the last decade, instrumentation has been developed that allows the application of seismic reflection methods to groundwater and engineering problems. At the Geological Survey of Canada, we have been developing and testing shallow reflection techniques for mapping the bedrock topography and structure within the overburden. We have attempted to develop methods which can be implemented with a minimum investment in equipment and computing capabilities. The data are recorded on a l&channel engineering seismograph, using a single high-frequency geophone per channel, and a hammer or in-hole shotgun (“Buffalo gun”) as the seismic source. Processing and display of the data can be accomplished on an Apple II+ or IIe microcomputer and an Epson wide-track dot-matrix printer.

Jan 1, 1991

By Gordon C. Petersen, Gary A. Almeraris

This paper describes the controlled blasting techniques required to mine a rock tunnel section of a main interceptor located in the Boston Metropolitan area. The 3m (10 ft) x 2.8m (9.25 ft) horseshoe shaped tunnel was driven 490m (1600 ft) by conventional drill and blast methods. The geology varied round by round and consisted of five highly faulted and jointed igneous rock types. The tunnel intersected numerous slickenslides and open mud seams which hampered both drilling and loading operations. Smooth blasting wee critical in order to keep overbreak tc a minimum in this extremely hard but blocky ground.

Jan 1, 1991

By Stanley Griff, William Herrera, William O. Seals

"The Navy initiated liquid propellant research in the early 1940's. The first promising Navy liquid propellant, Otto Fuel II, was developd in the early 1950 as a potential torpedo fuel. Later, the Navy developed a HAN based liquid propellant designated NOS-365, a hydroxylammonium nitrate, isopropylammonium nitrate and water formulation. A large gas volume generated by this propellant produced a large wake behind the torpedo. As one can readily understand, this negated the useof the propellant for this application. Recognizing the large gas volume as a desirable propulsion system for guns, the Navy embarked upon a gun propellant proqam. Utilizing a bulk loaded gun sysytem, the program failed when the gun was destroyed by the propellant detonating."

Jan 1, 1990

By Bruce Vandenberg, Andy Battfay, Don Lake, Steve Conway, Jeff Yorsz

"High-speed motion pictures are an invaluable resource for blasting analysis. Whether processed by the human eye or a computer, this imagery can provide important insight into a blast and its effects.While certainly popular, traditional high-speed film cameras hamper this process. Instant feedback is not available since film requires developing and, relevant in the case of automated analysis, film isnot immediately compatible with a computer. With these facts in mind, a new high-speed video camera system, the SVCSOO, has been developed. The SVC500 combines the capabilities of a high-speed film camera, the convenience of a solid-state digital video camcorder, and the computing power of a ‘486 PC to provide a complete, standalone platform for high-speed image acquisition and analysis. This paper will describe the design, features, and use of the SVCSOO andcompare these with the analogous aspects of film cameras."

Jan 1, 1994

By Rodney Pinksen, Remi Proulx

The IOC Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1.0 m x 1.0 m x 1.0 m; 39 inches x 39 inches x 39 inches) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures.

Jan 1, 2011

By P. O'Connell, J. Lever, C. Clemence

The Bulyanhulu Mine, Tanzania is constantly trialing ideas for improvements in the drill and blast process. The project work has resulted in a large number of choices in explosive type and charging methods being available for blast design. Interestingly, though booster sensitive bulk emulsion had been introduced to the site to reduce dilution, better results were being obtained from reduced charge columns (decoupled columns of poured anfo in 50mm pvc pipe) and pneumatically loaded anfo upholes, which had been traced. In order to compare the explosive type and charge up-methods, an explosives comparison trial was performed.

Jan 1, 2006

By Geraldine Woods

I work for the State of Washington as an Explosives inspector. My paper will describe the mission of the Wa. State Dept. of Labor pertaining to explosives and the regulation of explosives in the State.Blasting safety is high on the public safety list and the regulation of explosive use and storage has been mandated through legislature. The Dept. considers pro-active partnering forexplosive safety preferable to after-the-fact citations for non-compliance.In some cases, the Dept. will issue civil citations with monetary penalties, meant to be a deterrant, of course, to blasters who choose not to comply with the explosive regulations of the State.The Dept. has also revoked and suspended blasting licenses. In some instances, the Dept. has allowed recipients of citations with monetary penalties to reduce the amount paid by attending technical training classes. The idea here, is to reduce the chance of reoccurence of unsafe blasting practices. The State of Washington partners with MSHA in the regulation of explosives use and storage in mines, pits and quarries in the Stateas well as working closely with law enforcement, State and local fire marshals, ATF,and is active in ISEE in part of it’s ongoing effort to promote explosive safety and establish communications in a nonadversarial way with explosives users. My paper will include some statistics on licensing in the State, pounds of explosives used, inspection numbers, numbers and types of complaints with information from the inspections resulting of these complaints. My paper will include examples of storage, both good and bad, examples and pictures of fly rock incidents, accidents, near-miss close calls, break-ins, thefts, and abandoned explosives. This paper may also include a brief summary of my opinion of explosive regulation and my job as a regulator, including examples of high and low points of the job, joys and frustrations.

Jan 1, 2002

By Robert Boehnke, Bernd Mueller

This contribution presents an innovative, statistically supported method to predict blast vibrations in rock mass. For modelling the processes during and after detonation, a theory is employed which is based on linear momentum (so-called momentum theory), strongly supported by new measurement methods. During the course of the investigations, the following parameters have been found to dominantly influence vibrations: ! charge WB, includes geometrical factors such as borehole length and diameter (kg) ! detonation velocity cd of the explosives used (m/s) ! distance r between the points of emission and immission (m) and the statistically determined negative exponent n ! factor RM or RS of the rock mass which is related to the specific blast momentum and the drilling and blasting technique used and is statistically determined together with the exponent m (mm/kg or mms/kgm)

Jan 1, 2004