Search Documents

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By D VanDoorselaere

"Image analysis techniques are widely used for blast fragmentation measurement, and various commercial packages are available for this purpose. These packages are very versatile and serve as a useful tool for optimization of blasting practice. But many times, the results provided by image analysis techniques do not match with sieved and predicted data. This leads to the suggestion that understanding the limitations of this technology is as important as understanding its usefulness and versatility.A study was conducted in two stages:(a) Comparison between the results of image analysis and screened data using laboratory scale muck piles.(b) Comparison between predicted (Kuz-Ram) and measured (Image analysis) blast fragmentation results for several bench blasts.During laboratory work, muck piles with known size distributions were analyzed with the help of image analysis technique. A disparity was observed between the sieved and measured results because the image analysis techniques cannot accurately determine the % of fi nes in the muck. During fi eld work about fourteen blasts were monitored. It was observed that predicted (Kuz-Ram) results rarely matched with measured (Image analysis) results. The Kuz-Ram curves were modifi ed by changing the rock factor so that the Kuz-Ram and Image analysis curves match in the vicinity of the 50% passing size. The pairs of curves (modifi ed Kuz-Ram and Image analysis) were divided into three categories depending upon their differences in the coarse and fi nes ranges. The blast design parameters affecting the difference between the pair of curves have been outlined. The suggestions have been made to better utilize the image analysis system."

Jan 1, 2007

By Ricardo González Dumuihual, Carlos Scherpenisse

A monitoring campaign to record dynamic pressures generated by detonation of a single blasthole was implemented at Barrick Gold´s Pueblo Viejo Open Pit mine (PVDC), located in the Dominican Republic . Pressure amplitudes beyond the dynamic compressive strength of the electronic detonator´s capsules have the potential to damage these electronic devices, generating misfires along with all the associated risks and entailed safety implications. In most instances, misfires generated from high dynamic pressures are a direct consequence of drilling deviations resulting in blasthole distances smaller than originally designed.

Feb 1, 2020

By Yong Pan, Purushotham Tukkaraja

Block caving is a preferred underground mining technique due to its high production rate and low operation cost. Before its final step into a mature caving system using gravity to break rock, drilling and blasting are required to form drawbells to connect the production level and undercut level and induce the initial caving propagation in undercut level. A large amount of toxic fume generated by blasting activities poses a big threat to people working in a confined environment and ventilation is assumed to be the most economical and efficient way to deal with this issue. Past research shows that it’s common to use traditional methods like using a formula or using numerical method (Computational Fluid Dynamic (CFD)) simulation to predict re-entry time after each blasting, but it fails to consider the percentage of toxic fume entrapped in muckpile, which could reach up to 70%. In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

By Yong Pan, Purushotham Tukkaraja

In this paper, CFD was used to investigate the blasting toxic fume characteristics under different entrapping percentages and under changing muck pile properties like broken rock size and porosity. It showed that CFD was a very useful method to study blasting fume in an underground mine and it took much longer time to dilute toxic fume into a safe level with higher entrapping percentage. The dilution time increased with a decrease of broken rock size and porosity.

Feb 1, 2020

By Karl Christopherson, Vanessa de Viterbo

Trim blasting is an integral part of the mining processes at the Morenci Mine, a Freeport-McMoRan Copper & Gold Inc. property. Trim blasting near high-walls or Finals blasting requires a tighter distribution of energy but a reduction in total energy factor near the wall. Recent Finals blasting in Morenci Mine was allowing the shovel to dig to the final design limit, but causing high-wall instability due to excessive energy or production of energy (blast design and timing). Slope instability events reduced production in two of the three operating pits in Morenci over 2009. In order to avoid high-wall instability from Finals blasting, a new method was required. The new method utilizes air-decks, unconventional row timing, and blast design based on the geology predicted. Many different geologic structures and rock types exist in Morenci, and different strategies were needed for the many predicted geologies. Drill penetration rate and core mapping were the primary tools for determining the blast design. Patterns were designed within a consistent geology; with weaker rock types receiving a lighter load than the stronger rock types. Penetration rate returned by the drill would be the determining factor on the actual rock hardness. Maintaining the pattern geometry on Finals designs should not be an issue as long as the lb/hole is adjusted to reduce powder factor close to the high-wall. One requirement of Finals blasting should be that the powder factor matches the geology as closely as possible. A softer, fractured zone should use approximately one-half to two-thirds the explosive charge of a competent, sound geological zone. This has been incorporated into the final Trim blast design. It is impossible to protect every high-wall from close-in blasting, especially those with crossing prominent joint sets inclined toward wedge failure, but this new design has provided protection on walls where the mine was encountering problems.

Jan 1, 2011

By C. Breeds, K. Jeremiah, E. Jennings

Washington State has a well developed set of blasting regulations which have been promulgated by the Department of Labor using extensive stakeholder input, not only from citizens but also from manufacturers and representatives of IME, blasters in charge, blasting engineers, blasting companies, local and federal law enforcement agencies, fire officials, and local and state government representatives. WAC 296-52 therefore provides a foundation or platform for developing city ordinances for Washington State cities should a City wish to do so. On the other hand, Oregon’s code is based on OSHA 1926, Subdivision U, Blasting and the Use of Explosives which provides scant direction regarding the modern use of explosives. Reference is also made to ODOT Section 00335 - Blasting Methods and Protection of Excavation Backslopes. This paper examines two separate programs that have been developed by two Cities, one in Washington State and one in Oregon to further regulate blasting inside City limits and discusses why the lack of a regulatory foundation made one approach more difficult than the other. One of the authors was retained by the City of Kennewick, WA to develop their ordinance and has more recently followed and reacted to a pending ordinance for the City of Redmond, Oregon. The paper will compare and contrast the different approaches and comment on the reaction from both Blasters and the public. We also present a case study that involved blasting in an urban area of Oregon to prepare a foundation for a water tank. Controlled Blasting was carried out within 70-ft of residencies and within a community that had expressed reservations regarding blasting even though the work would make a significant contribution to the betterment of the community. Pre-construction surveys of residencies located in a large area surrounding the site were performed and a well-planned blasting program was carried out. Residencies were subject to vibration levels that were monitored using six seismographs that surrounded the site and these units measured vibration levels that were significantly lower than allowed by statute. There were complaints triggered by individuals reactions to blast vibrations which validated commonly held models of human perception but no damage was caused by the Blasting.

Jan 1, 2024

By Juan Carlos Vasquez, Romel Villanueva

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process.

Feb 1, 2020

By C H. Dowding, P W. Linehan

Many of the technical and non-technical or human problems associated with blasting can be minimized through a proper preconstruction test-blast program.

Jan 1, 1986

By Dale L. Ramsey

The Pinkerton Tunnel Open Cut Project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 6.4 meters (21 feet) of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between Mid-Atlantic States and their ports to Midwest Markets in the U.S.

Jan 1, 2014

By D G. Dressler, Paul Yeager

A previously little-known facet of seismic frequency spectrum analysis is gaining significance. The frequency spectrum of seismic waves promulgated from blasting is a significant factor in causing blasting complaints and threshold (architectural type) damages.

Jan 1, 1987

By Donelson A. Robertson

Proper coupling between the seismograph transducer and the surface is the most important aspect of seismograph monitoring but probably receives the least attention in many blasting situations. Without good coupling, particle velocity measurements may be higher than actual and frequencies may be lower. If the field data are inaccurate, sophisticated instrumentation and computer programs cannot correct the readings.

Jan 1, 1993

By Michael S. Stern, Gordon P. McDonald

The increasing costs and problems associated with transporting and safely disposing of used engine oils from remote mine sites have caused mining companies to consider other ways to consume their used oil. One practical method of disposing of these used oils is to blend them with the diesel component of ANFO and Heavy ANFO type explosives.

Jan 1, 1993

By John F. Vynne

This paper will discuss the application of available monitoring technology on blasthole drills with the goal being to reduce costs and increase productivity. Case studies from the monitoring of blasthole drills in North American open pit mines will be used to illustrate the ability to meet these objectives.

Jan 1, 1997

By Qingshou Chen, Paul N. Worsey

It has been recently argued that rock strength has little effect on the final results of pre-split blasting and is of only minor importance when blasting rock in general. However, it can be shown that the maximum borehole separation for optimal perimeter blasting results with constant borehole and loading configuration is strongly dependent on the tensile strength of the rock.

Jan 1, 1986

By J R. Brinkmann, S G. Giltner

Nearly all of the South African gold mining industry still uses fuse and igniter-cord initiation systems. Over the past 30 years numerous attempts at developing new initiation systems have not yielded a viable alternative. New initiation systems for narrow stopes are currently being developed by various concerns and the likelihood of these efforts producing feasible alternatives is greatly improved due to the recent advances in electronics technology. The greatest potential benefit of alternative initiation systems is increased production rates through improvements in accuracy and reliability of firing over that of fuse/igniter-cord. Another important feature is the capability of millisecond delay firing as this can lead to reduced stope cleaning times by way of enhanced rock throw and improved fragmentation characteristics.

Jan 1, 1989

By Bert Bahnson

As farms decrease and subdivisions increase there is a continuing demand for easy and safe silo removal. A few years ago I attended one of the Omni istribution explosive classes and was impressed by a product designed by Omni owner Bill Nixon called the Omni Breach. Its original purpose and main current use is law enforcement; specifically door breaching and tactical operations, with most of the force coming from water using a minimal amount of explosive component. I experimented with various charge strengths on concrete and found that it can be easily shattered with little flyrock or airblast. A neighbor of mine had an old silo within a foot of a barn that he was rebuilding and inquired about its removal. His property was sandwiched between an elementary school and Interstate 40, so I told him that I would do some test shots and if the results proved satisfactory, I would take the job for free to test the following theory.

Jan 1, 2006

By Dale Preece, Stephen Chung

The DMC-BLAST (Distinct Motion Code) has been developed for modeling bench blasting to one or two free faces such as choked blasting in surface gold operation and cast blasting in coal mining, respectively. This computer code has been used to assist the analysis of rock mass displacement after a blast was initiated in an orderly delay sequence. Applications of this feature can be found in the studies of dilution control in surface mining of gold as well as coal involving complex rock structures. Recently, DMC-BLAST has been modified to include a designated delay firing order coupled with variable rock strengths in the blasted media. This newly added feature allows the investigation of the effects of delay firing order on rock displacement in blasting a complex interbedded ore-waste structure. Examples of blasting a steeply dipping coal seams and bedded rock structure, especially in coal mining operations will be addressed and the comparison of efficiency in blasting in an up-dip as opposed to blasting in a down-dip direction will be discussed. Also covered in the paper is a new application of DMC-Blast to simulate a stope blasting underground. Simulations of blasting in a few selected types of timing/structure combinations will be presented in this paper.

Jan 1, 2000

By Lina Lopez, Jose Sanchidrian, Manuel Lopez, Pablo Segarra

Previous work in which rock properties and blasting parameters (geometry, charging and timing) were reported together with truck filling times, is taken as a starting point for a thorough analysis of the influence of the former on the mucking velocity. The experimental set was composed by 11 blasts made in an open pit mine. Non-parametric, distribution-free statistics is applied. The mucking rates (in bank cubic meters per unit of bucket volume and per hour) appear to be clearly dependent on the explosive energy and powder factor, both magnitudes combined as energetic powder factor (energy per unit of rock volume). The mucking rate is a non-monotonic function of such factor in the range of the blasts analyzed. The determination of the function is optimum when the fraction of the explosive below grade is not considered and when the explosive energy is qualified as that delivered at a partial detonation regime. Different types of loaders seem appropriate for different energy levels. At low levels both front loaders and rope shovels obtain small productivities without a statistically significant difference in their performance. At high energy levels, front loaders qualify higher than rope shovels. Mucking velocities can be equally small at low energy powder factors and at high ones if rope shovels are involved.

Jan 1, 2008

By Remi Proulx, Ruilin Yang

The effectiveness of presplit in soft or fractured ground is hard to visualize or quantify. There have been many attempts by the blasting community to measure and quantify the effectiveness of presplit blasts. Various methods have been adapted by different researchers, and the results are debatable.

Jan 1, 2019