Search Documents

By S. K. Dutta

Enormous amount of iron ore fines is generated, due to partly soft and friable nature, during mining. Coal fines are also produced during their processing. These fines cannot be used directly in ironmaking reactors. Utilization of these fines for extracting metal is of vital concern for resource conservation and pollution control, and therefore, a novel concept of agglomeration by cold-bonding is developed. Composite briquettes/pellets of iron ore fines with coal fines were prepared in the laboratory by cold-bonding technique. Various binders such as lime, Ca(OH)2, slaked lime, dextrin, molasses, fly ash etc were employed either alone or in combination in different proportions for making composite briquettes/pellets. It was possible to obtain dry strength of composite briquettes more than 300 N/briquette in some cases and more than 200 N/briquette in many trials. The combination of fly ash with slaked lime and molasses produced the highest strength, more than 400 N/briquette. Drop strength and shatter index values of composite briquettes/pellets were also measured. In briquettes, best compressive strength (978 N/briquette) is observed by using polyvinyl alcohol (PVA) binder. In pellet, best compressive strength (362 N/pellet) is achieved by PVA; shatter index (0.1%) and dry drop strength (158 numbers) are also good. Compressive strength above 200 N/pellet is obtained by fly ash, slaked lime and molasses combination.

Sep 1, 2012

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By N. Syna

The selection and preparation of activated carbon suitable for specific application can often involve exhaustive adsorbent preparation and testing. This work examined an emerging technique based on modelling the correlation of observed adsorption capacity to the carbon characteristics as a means of decoupling the roles of carbon textural and surface chemical properties. The insights to these specific roles are then used in tailor-making adsorbents and in establishing the optimal carbon properties for specific application. In this study, a series of activated carbons prepared from bagasse by physical and chemical techniques and commercially available carbons were used in developing the models. These carbons were tested for the adsorption of thiourea-gold (I) chloride complexes. Thiourea is an important alternative gold lixiviant with the potential to address current ecological and safety concerns in the extraction of gold. A four-component model, which correlated the adsorption gold capacity to carbon textural and surface chemical properties, was proposed. The model fit was assessed using multi-linear regression and a partial F-test. This was followed by goodness of fit test achieved through r2, adjusted?r2 and mean square error (MSE) values. The results suggest the adsorption of the gold-thiourea complex is strongly influenced by the internal surface area and pH of the carbon. Tailor-made activated carbon from bagasse showed adsorption gold capacities of up to 198 mgAu/g adsorbent, demonstrating the potential of bagasse as a precursor for gold adsorbents and of this empirical modelling approach in developing adsorbents for metal recovery.

Jan 1, 2014

By R. B. Shu

A moderate thermophilic microorganisms, has been isolated (45?) from a typical sulphide mine in the region of Mo Jiang located in the southwest of China. The culture has been used to extract copper from chalcopyrite concentrates obtained from De Xing copper mine. The majority of experiments were carried out in 300mL Erlenmeyer flasks containing 150mL volumes of mineral suspension. Effects of some variable parameters such as solids concentration, pH and the concentrations of inorganic nutrients on the bioleaching of chalcopyrite obtained from De Xing copper mine were investigated. For a given concentrate the most important factor affecting the fractional copper extraction was the size of the mineral particles. The overall rate of leaching was found to be limited by the area of mineral surface. The attack started in cracks and genetic defects and finally reached the whole chalcopyrite surface. As a consequence of this, the ore showed strongly cracks. The additive of ferrous sulfate increases the bacteria activity, but did not improve chalcopyrite bioleaching. The results indicate that the nature and relative proportions of the various minerals present have been shown to be important factors.

Jan 1, 2014

By R. A. Kleiv, H. Havskjold, N. Church, T. Malvik, M. Tro, E. Larsen

Liberation is one of the major purposes of comminution in mineral processing. In the simplest form, two or more minerals are present in a particle and have to be reduced such that the individual particles contain only one mineral. The complexity of the mineral intergrowth varies from ore to ore. Poor magnetic separation of iron ore may have many causes. In this paper, the emphasis is given to the problem of fine magnetite inclusions in quartz or other gangue minerals. This is highlighted by two Norwegian cases: one on a magnetite ore and the other on a hematite/magnetite ore. The inclusions in question are so small that they are not liberated by reasonable grinding. In both cases, the result has been either poor recovery or lower grade concentrates than desired. The first example concerns production of direct reduction concentrates from magnetite. Magnetic inclusions in gangue particles will be magnetized enough for the particles to pass into the concentrate. The second example is given a more detailed study, where the problem is caused by silicates with small inclusions of magnetite in a combined LIMS and WHIMS separation. This study included microscopy, Davies tube testing, and magnetization measurements. In particular, large gangue particles with magnetite inclusions were shown to have a tendency to bypass the LIMS separators as drag forces in presence of hematite are large. Such particles will then be picked up by the WHIMS as their magnetization is higher than for hematite. This was demonstrated by Davies tube tests, which indicated that such particles were picked up in preference to hematite particles. However, the Davies results did not give a good quantification. Magnetization measurements of gangue particles with magnetite inclusions was shown to be a better tool to quantify the magnitude of the effect of magnetite inclusions in magnetic separation.

Jan 1, 2018

Optimising flotation designs and innovations is a complex process involving many parameters, one of which is ensuring sufficient testwork is carried out at plant level before these innovations are launched in the marketplace. This paper will describe how modern design tools are utilized, what are testwork phases at various plants and how results and observations have helped to validate and optimise flotation design innovations. Scale-up of equipment has long been the prevalent trend, but how long can it continue? Are there other means for pushing the boundaries of present technology? Some present challenges and future directions are given in the light of theoretical criteria for scale-up and how it has been applied in practice. Very large flotation cells of 300 m3 size have been installed in New Zealand, and relevant results from the metallurgical and mechanical aspects are presented and discussed. Utilization of the cell volume is also important. New innovations in the hydrodynamic domain are presented and discussed. Means to enhance flotation of coarse and fine particles are shown with results from plant testwork. Accurate control of large flotation cells is vital to optimize yields and grades. Froth image analysis and intelligent level control are presented ? again - with relevant plant results.

Jan 1, 2014

By J. Y. Liu

The comminution in a high-pressure roller mill is modeled by an energy-based population balance approach considering three aspects of breakage taking place in the active zones of the mill: the interparticle breakage in the high-compression zone, the breakage at the edges of the rolls, and the pre-breakage in the acceleration zone. Together with an appropriate model of classification, this model can be used to simulate steady-state performance of closed-circuit grindings with high-pressure roller mill. After a brief description of the basic modeling approach, the algorithm of the steady-state calculation for a generalized grinding-classification circuit is presented, from which the circuit configurations commonly met in industrial practice can be derived. With an iron ore as feed material for example, simulation results are shown and discussed in respect of circulating load, specific energy consumption and product fineness for closed-circuit grindings under various operating conditions. The effects of stressing intensity, working gap, classifier parameters as well as circuit configuration on the overall circuit performance are investigated systematically by means of computer simulation.

Jan 1, 2014

By R. T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and-error techniques. This paper introduces a two-dimensional finite element model of briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, the velocity field, the stress distribution, roll force and torque. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquette after its exit from the roll. This enables to perform realistic computer experiments which are helpful for establishing the forming cavity geometry and process conditions necessary to produce briquettes with the desired properties. Three forming cavity profiles are analyzed. Results from model are verified on experimental roller press and best cavity profile is recommended for briquetting of sub bituminous coal fines.

Jan 1, 2014

By Yuhe Tang, Jun Zhang, Jianguo Liu

"The nature high carbon graphite with fine particle size has low commercial value because of its narrow application range. In order to improve its value, this paper has studied the methods for nature spherical graphite. The nature spherical graphite can be used as the battery material in the field of electronic product battery and new energy automobile battery, basis on the physicochemical characteristics and particle feature of graphite. In this research, the Fixed Carbon (FC) grade of the graphite sample is more than 95.0% and the particle size of the graphite sample is from +325 mesh to -100 mesh. There are many methods for nature spherical graphite, including the fluidized bed airflow mill, the hydro-spheroidization mill and micropowder mill. The testing results indicate that the method of ACM micropowder mill is the best because the spherical shaping ratio and production yield of spherical graphite are both the best.According to the testing results of the ACM micropowder mill, the best process includes two stages of coarse crushing, four stages of fine crushing and twelve stages of shaping. And two kinds of spherical graphite products can be got, which are the product of D50=22.85 µm and the product of D50=15.43µm, and the whole yield of them is up to 54.43%. So, it lays a foundation for the high value utilization of this kind of graphite resources.INTRODUCTION Graphite is isomer of the diamond. Graphite ore resources are mainly concentrated in China, Brazil, India, followed by Czech, Korea, Mexico, Canada and other countries. Graphite ore has lots of characteristics by itself crystal structure, such as good resistance to high temperature, electrical conductivity, thermal conductivity, thermal shock resistance, good lubricity, plasticity, chemical stability and so on. So, Graphite is widely used in metallurgy, machinery, electrical, chemical, petroleum, nuclear industry, defense industry and other areas. [1,2,3] Natural graphite ore has low geological Fixed Carbon (FC) grade. FC grade should be enriched to more than 94.0% by mineral processing. [1,2] The particle size composition of this high carbon graphite affects its application value. The part of +100 mesh particle size has high application value. The part of -100 mesh particle size has low value because of its limited application field. In order to improve the value of-100 mesh particle size, this part high carbon graphite can be made into spherical graphite. And the value of the spherical graphite is great, it is more than 8 times of the feed. This paper has lots of tests for spherical graphite preparing with the fine particle size natural high carbon graphite. And it lays a foundation for the high value of this kind of resource."

Jan 1, 2018

By Jury P. Nazarov

"At present the traditional study of crystal lattices of nmerials in a topic “flota tion mineralogy ” is used up. The present investigation is development of the a sclsical approaches to t he analy sis of ideal crystal lattices and f ormation on the basic obtained results of consultation, having practical chara cter.The strategy of develop ment floatation reagents i s offered, which basic pr inciple – complementary assembling m olecules forming surface co mpounds so thatth e steric charact eristic of the “visitor "" (of a polar gro up of molecule SAS) corresponded to the st er ic requirements of the ""o wner"" (elementary cell of a mineral), or coincided inter molecular cavities). In itsh case process of for mation of surface com pounds ca n be considered(a first approximation) as a realization of a principle of the design er "" LEGO "".The approach, which basic idea consi deration actioonf reactant ions and ions of ele mentary cell as three-di mensional objects is developed. And at suchp paroach the laws of a ster eometry - laws describin g spatial effect s are applicable. Thus it is possible toconsider a miner al surface as a mat r ix - basis for formation of the requirem ents to polar group of a molleec cuollector, and or (it is possible) depressant. As a whole approach represents a generalized principle double com plementation, enveloping both power, and geometric asp ects (concept ""lock "" and “key "" - spatial conform ity. Figure 7 (left). Fragment of a crystal lat tice of ap atite. Oleic acid ions interact on ly with th e calcium cations locate d on a long axi s of an elementary c ell. Magenta colour represe nts the calciu m cations, which are n ot particip atin g in interactio n, as th e degree of screening by ions neighbours exceeds 1.Figure 2. (right)The illustration of space complementary. “Afterbuilding” an elementary cell of apatite (radical PO4) related molecules of the visitor – alkyl phosphate (polar group PO4). Cations of calcium are not shown."

Jan 1, 2003

By David Verrelli, Melissa Kistner, Leanne Smith, Chris Aldrich, Lidia Auret, Warren Bruckard

In this investigation, different mixtures of realgar and orpiment particles were floated in a laboratory batch flotation cell and multivariate image analysis was used to estimate the arsenic content in the froths. The analysis was based on the froth colour, as well as extraction of three groups of textural features, namely those based on grey level co-occurrence matrices (GLCMs), wavelets and local binary patterns (LBPs). Collectively, these features provided better information on the arsenic content of the froths than any one of the individual groups of features. Partial least squares models could explain approximately 78% of the variance in the arsenic by using all the features combined. The colour content, particularly the green component in the red-green-blue (RGB) features, provided almost as much information as each of the three sets of texture-base features individually.

Jan 1, 2014

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. In Kure, a very fine grinding requirement for an adequate level of liberation makes a successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu Column flotation tests were conducted at the plant site using two different column types The experiments proved that the grade of the concentrate could be increased from about 14% Cu to 25-26% Cu. Murgul Cakmakkaya Copper Concentrator is the largest copper concentrator in Turkey. Although concentrate production capacity is around 170,000 tons annually with 22-23% Cu content, this figure tends to be much lower than that. In Murgul a Turbo Column of Multotec Company of South Africa was employed. As a result of systematic column flotation tests, the grade of the concentrate was increased from 20.3% Cu to 28.7% Cu.

Jan 1, 2003

By C. Kleine

Coal sorting with an x-ray-transmission (XRT) sensor has experienced a lot of development since first described by Jekinson et.al. in 1974. Powerful computers and increasingly sensitive X-ray scintillation counters enabled the development of high-performance sensor-based sorting machines. The first industrial installation of a belt-type XRT-sorting for coal is in operation since 2004. It is upgrading high quality coal from 1% ash to 0.7% ash for cathode production. In comparison to the high quality coal which is treated with a belt-type sorter, the chute type sorter has been successfully optimized for high volume coal treatment of lower quality coals. This project was funded by the German Environmental Fund (Project Nr.244444). In cooperation with the RWTH Aachen University and Isambane Processing, CommodasUltrasort(now Tomra Sorting Solutions) conducted extensive pilot test work under production conditions in 2010 for the destoning of power station coal at Arnot Power Station in South Africa. The experience gained during this pilot test phase led to an optimized, redesigned PRO Secondary XRT Chute sorter which is now in operation at a South African coal mine. This flexible semi-mobile modular destoning plant is treating a size range of -120 mm +30 mm at a throughput of 150 tph. The implementation of this plant not only reduces the ash content, abrasiveness index and sulfur content significantly, but also reduces royalties, water treatment and transport costs.

Sep 1, 2012

By O. Güven

In recent years, there is an increasing demand on manganese consumption which stems from the important role of manganese in carbon steel production. And the growing need for manganese ores makes the beneficiation of low-grade manganese ores more economical. In this study, the characterization and beneficiation studies were carried out to propose a flow sheet for typical low-grade Turkish manganese ores. For this aim, different gravity separation methods were applied. According to the mineralogical analysis, the major mineral phases are pyrolusite (MnO2) and psilomelane (MnO2) while the major gangue mineral is radiolarite. Gravity separation tests were accomplished by using jigs, shaking table, MGS (Multi Gravity Separator) and in order to obtain products with high Mn ratio, high intensity magnetic separation was also performed. As a result, different combinations of flow sheets were utilized and a concentrate assaying 56.5% Mn with 85 % recovery was obtained.

Sep 1, 2012

By Qiuyang Hong, Bo Li, Dongyun Liang

"A weathering-crust niobium-rare earth-bearing deposit is formed by the weathering alterationof alkaline granite, which is refractory due to its low grade and complex properties. The mineralogicalcomposition of ore, the grain size of majorminerals as well as the occurrence of Nb and REE are studied in this paper using MLA combined with traditional methods. According to the results, a wide range of Nb-Ti-REE compound minerals including titanoniobite, uranpyrochlore, chlopinite, samarskite and ilmenorutile areformed for the extensive isomorphous substitution among the elements of Nb, Ta, REE, Fe, Ti, U and Th. The occurrence of REE is extremely complex. First, the REEexistingas rare earth minerals including monazite, xenotime, bastnaesite,etcaccount for 21%. Second, the REEexist in the lattice of Nb and Zr minerals as isomorphous additions, which account for 18%. Third, the REE exist as colloidal rare earthdeposit,which account for 35%. Last, the REEexistingas ion-adsorption-type rare earth,which are adsorbedon the kaolinite in the form of hydrated hydroxyl ions, account for 26%.Based on the results of mineralogy, the combined technology process "mineral processing- hydrometallurgical separation" is needed to deal with the ore. The mineral processing tests show that, for the feed ore containing Nb2O5 0.065%, REO 0.13%, an Nb-REE concentrate containing Nb2O5 1.38%, REO 1.98% can be gained by "high intensity magnetic separation-regrinding-gravity separation by shaking tables". The recovery of Nb2O5 and REO is 62.42% and 44.78% respectively. The Nb-REE concentrate is dealt by the metallurgy process "direct reduction- acid leaching & acidulating- neutralization & precipitation- chlorination & distillation" and the rare earth oxide of 92.34% REO as well as the Nb-Zr oxide of 24.62% Nb2O5 can be obtained with the recovery of REO and Nb2O5 being 76.83% and 59.37% respectively."

Jan 1, 2014

By Petrus van Staden, Dragan Milanovic, Francisco Sánchez, Eero Kolehmainen, Carlos Frias

"Currently there is no economical and viable process for on-site metal extraction from Low Grade, Complex or Poly-metallic deposits, and even more, there is not any industrial process or technology able to deal with polymetallic or bulk concentrates containing Cu+Zn+Pb base metals and also precious metals. Traditionally, metals recovery from polymetallic sulfide deposits is performed by mining, selective flotation to separate Cu, Pb and Zn concentrates, and finally, smelting/refining of those concentrates to obtain the refined metals. In many cases, selective flotation of that kind of complex ores produces low metals recovery and low concentrate quality containing impurities such as Hg, As, Bi, etc., which results in high penalties in treatment and refining charges, and consequently, worsening the economy of the mining business. Recovery of the valuable metals from Polymetallic, Complex or Low Grade ores could then be maximised by producing bulk concentrates or middling flotation products to feed novel hydrometallurgical processes, like the integral metallurgical system that is currently under development within the INTMET project. For example, producing bulk concentrates would increase more than 100% Cu+ Zn+Pb cumulative recovery versus conventional selective flotation. Founded by the Horizon-2020 EU Programme, the INTMET Project was started in February 2016 and will be running over three years. The INTMET consortium is led by Cobre Las Cruces (Spain) and integrates twelve partners from seven EU countries, and including Serbia and South Africa as well. The INTMET project represents a challenging opportunity to develop suitable technological solutions to deal efficiently with difficult, polymetallic and complex sulphide ores that are abundant in Europe and worldwide. Main activities carried out during the first 18 months of the INTMET project development includes: (i) An atmospheric leaching pilot plant having a capacity of 300 kg/h bulk concentrate which has been installed and operated continuously for nine months at the Las Cruces mine; (ii) Pressure leaching test work developed by Outotec; (iii) Bioleaching test work performed by Mintek in collaboration with MMI Bor. Prior test work was applied on bulk concentrate samples supplied from Spain, Portugal and Serbia. Some of the results of these technological developments have been very positive and are presented in this paper."

Jan 1, 2018

By U. A. Peuker, T. Mütze, F. Shayo, A. Wikedzi

"Buzwagi Gold Mine (BGM) is operated by Acacia Mining and located in the Lake Victoria Goldfields of central Tanzania. The mine treats a sulphide copper-gold ore to produce gold in form of doré bars and a concentrate containing gold, copper and silver. The BGM comminution circuit includes a primary crushing stage with a gyratory crusher and two grinding circuits using a Semi-Autogenous Grinding (SAG) mill and a ball mill. Currently, the grinding circuits are inefficient in achieving the aspired product fineness of xP,80 = 125 µm even at low to normal throughputs (450-600 t/h). An optimization study of the circuit performance was conducted to improve product fineness through circuit surveys, experimental lab work and simulations. The analysis of survey data revealed inefficient grinding operation characterized by ball mill product (xP,80 > 400 µm) coarser than designed and higher hydrocyclone cut sizes (xT > 200 µm), too. In MODSIM several options were simulated such as reduction of vortex finder and apex diameters, reduction of SAG screen aperture, and modification of cyclone feed density. An improvement of product fineness could be achieved by simulation of the cumulative changes but it was also concluded that the current equipment cannot achieve the target. Further simulations showed that a second ball mill might help to achieve the desired fineness as well as an increase of grinding throughput by up to 26 %. INTRODUCTION Simulation of comminution, particularly grinding and classification, has received great attention for many years, due to the fact that the unit operation is by far the most important both in terms of energy consumption as well as overall plant performance (King, 2001; Wills et al., 2006). The use of simulation is advantageous due to low cost as well as its ability to consider many variables simultaneously. Moreover, there are some benefits for optimizing grinding operations by simulation like decreased unit operating costs, increased capacity, and improved performance of downstream processes due to improved feed size distribution. This paper presents an optimization study for the grinding efficiency at Buzwagi Gold Mine. This was achieved through three full scale circuit surveys, lab work and simulations with MODSIM."

Jan 1, 2018

By N. Nehoroshev, P. Solozhenkin, N. Voyloshnikova, A. Pshennikov

"Molecular modeling of clusters of major bismuth minerals, Bi2S3, was carried out whereby molecular models of minerals and reagents clusters were created. Their HOMO and LUMO energy levels were calculated and using known modelling equations, the absolute hardness ?, eV and electronegativity were calculated. The charges of separate atoms of clusters and the change of properties of the minerals were determined which allowed predictions of the flotation properties of raw ores containing rare bismuth minerals. Modeled complexes containing the clusters of minerals and various collectors were constructed, consisting of atoms and bonds within clusters of minerals. Major physical and chemical parameters were determined for the complexes created, including the total and electronic energy. Based on the energy calculations, predictions of the collector efficiency were proposed. The efficiency of collector was established for various thiolic reagents, the compounds of phosphorus (III) and mixtures of reagents. Theoretical results were checked and confirmed against laboratory ore flotation tests. A gold-bismuth-magnetite ore type was studied where gold, bismuth and iron (magnetite) are of industrial interest. The ore contains 2.8 g/t Au, 1.0 g/t Ag, 0.26% Bi, 45% Fe and 1.25% As. Sulphide mineralization can be mainly found in the form of pyrrhotite, pyrite and arsenopyrite. Bismuth can be mainly found in the form of bismuthite and native bismuth. Gold is fine. A flow sheet for Zhelezny Kryazh ore treatment was proposed. This flow sheet consists of grinding to 95-98% -74 µm, sulfide flotation with two cleaner with xanthate addition, cyanidation of flotation concentrate and flotation tailings included treatment with with CaO (6 kg, 6 hours), cyanidation (8 hours) and CIL (8+24 hours). Saleable products are gold doré, bismuth and iron concentrate."

Jan 1, 2014

By Montaser S. EL Salmawy, Takahide Wakamatsu, Eishi Kusaka

"In conventional flotation, fluoride ions selectively would react with the aluminum site on the microcline surface and produce negative charged sites for amine to be adsorbed (Smith, 1976). According to this view, aluminum site is considered as a key feature in feldspar flotation. Generally, fluoride ion has been widely used as a modifying agent in silicate flotation. Since O'Meara's patent appeared on HF -amine reagent system to selectively float feldspar from quartz in 1942, relatively few contributions have been devoted in this issue. The reason might be that the process works very well, and accordingly there is no initiative to investigate in this area. However, due to the awareness of international community to restrict using of hazardous reagents like HF, sound engineering practice to search for alternative methods, not utilizing HF, has been launched. Inspection of literature, one can find several works dealing with this issue.In this contribution, the effect of ethoxylation of long chain alcohols on the quartz and feldspar flotation behaviors was investigated for surfactants of the octylphenol polyoxyethylene family. The tests were carried out with an average of 7.5 (Triton X 114), 9.5 (Triton X 100), 30 (Triton X305), 40 (Triton X 405) and 70 (TritonX 705) oxyethylene units. Electrokinetic and flotation studies on quartz have shown that at low pH values, quartz could be floated with polyoxyethylene octytlphenols. The possible mode of adsorption of these nonionic surfactants may be suggested to be due to hydrogen bonding between the oxygen of ether and hydrogen in the free hydroxyl groups on quartz surface. It was anticipated that the selectivity between quartz and microcline would decrease as oxyethylenic chain length increases."

Jan 1, 2003

By I. A. Makalin, V. N. Yakovlev, S. V. Imangulov, I. V. Zyryanov

"The presented studies aimed at solving the problem of recovery of low-luminescent diamonds, which are not recovered using X-ray luminescence method of processing of diamond-bearing ore. The purpose of the studies is the determination of possibility and feasibility of recovery of such crystals using dual-energy X-ray transmission separation technology. In preparation for studies methods were developed for testing technical and process parameters of XRT-400 Aliud GmbH (Germany) sorter, manufactured according to design specifications of Yakutniproalmaz Institute, and XRT/D TOMRA Sorting Solutions GmbH (Germany) sorter, designed for processing of -50+5 mm ore, as well as RGS-1M, RGS-2 X-ray sorters, developed by JSC NPP Bourevestnik (St. Petersburg) in cooperation with Yakutniproalmaz Institute, for material size of -6+3 mm. In 2018, in-process tests of RGS-OD-3 X-ray sorter prototype on material size of -3+1 mm are scheduled. Studies to determine the content of low-luminescent diamonds and feasibility of their recovery using XRT-400 and XRT/D sorters at the Processing Plant #3 of Mirny Mining and Processing Division (MPD) were carried out. The results of the studies confirmed presence of such diamonds and possibility of their recovery using the dual-energy X-ray transmission method. In-process tests of RGS-2 X-ray graphic sorter were carried out at the Processing Plant #16 of Nyurba MPD. According to the results of sampling of RGS-2 sorter separation products, the recovery of -6+3 mm sized diamonds from tailings of X-ray luminescence sorters was achieved at the level of 96%, while the diamonds recovery was 98.5% in value terms, the concentrate yield was 0.1%. In-process tests of RGS-1M sorters at final recovery of the grease separation concentrate at the Processing Plant #3 of Mirny Division were carried out. Recovery of low-luminescent -6+2 mm sized diamonds by RGS-1M sorter amounted to 92.4% for single operation, and with the double control operation reached 99%. As a result, -6+2 mm sized base product recovery increased by 0.2%."

Jan 1, 2018