Search Documents

By S. J. Lui

Sodium oleate was an effective diaspore collector, whereas chelate collector OL2 showed certain collecting power over diaspore and nonionic surfactant OL3 showed little collecting ability. Then experiments were carried out using sodium oleate as the main collector with the addition of OL2,OL3 to study the influences on diaspore flotation, it could be seen from the experiments that accelerants had a marked influence on the recovery of diaspore, which could be raised by 10%, and the addition sequence also affected the flotation behavior: the best results could be gained when the accelerants were mixed thoroughly before adding and the best ratio of collector OL1 and accelerant OL2, OL3 stood at 30:2:1. Based on the calculation of the ingredients in the sodium oleate solution, sodium oleate reacted with surface of the mineral and formed the acid-soap polymer [HOl?Ol-] when pH was about 9. Zeta potential test showed the accelerant promoted the absorption of collector on the mineral surface, which lowered zeta potential. As could be seen from surface tension experi-ments, the addition of accelerant OL3 lowered the CMC value of OL1 solution, which was equiva-lent to raise the power of the agents. Further Infrared Ray experiments showed the co-absorption of OL1 and OL2 make aluminum oleate on the mineral surface more stable. Up till now, the mixed reagents with sodium oleate as the main collector, combined with other two accelerants had been used in the Zhongzhou concentration plant, which is the first diaspore flotation plant in China.

Jan 1, 2014

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By N. Acarkan

Slags usually contain some quantity of valuable metals. They are actually a secondary resource of metals, rather than an end-waste and have been utilized as a resource material in many areas. In addition, for some applications, slags have comparable or even better properties than their competitors. Leaching is a method for extraction of metals from copper slags. The extraction of metals such as copper and cobalt from the copper slag of Küre-Turkey, was investigated in the past decades. Fayalitic type of these copper slags containing 0.934 % Cu, 0.353 % Co and 50.91% Fe were subjected to the experimental study. As a result of mineralogical analysis of the slag sample, fayalitic type of slag was found to contain hercynite, magnetite, hematite, pyrite, chalcopyrite, covellite, bornite and metallic copper. Direct acid leaching methods were applied on the sample. Effects of leaching time, temperature and acid concentration on Cu and Co leaching recoveries were investigated in the direct acid leaching. The optimum leaching conditions were found as leaching time of 2 hours, solid/liquid ratio of 1/3, H2SO4 concentration of 125 g/L and temperature of 70 °C. At these conditions, 75.5 % of Cu, 95.6 % of Co and 70.9 % Fe were extracted. In the second stage of the leaching experiments, copper in the pregnant solution was precipitated by cementation to produce a Cu concentrate assaying 95.58 % Cu; cobalt was obtained by precipitation with H2S to produce a concentrate containing 62.10 % Co. As a result of this study a process flow sheet has been developed for recovering Cu and Co from these slags to demonstrate its economic and technological benefits.

Jan 1, 2014

By N. J. Bolin

The Aitik copper mine is located in the north of Sweden and the concentrator at the mine started its operation in 1968 with a capacity of 2 Mton ore per year. Since then the operation has expanded several times, and today the capacity is 18 Mton ore per year. A new expansion plan was investigated in 2005, however the building of a new concentrator was found to be a better solution, giving a lower cost, a longer lifetime and more concentrates to the smelter at the coast. Several choices have been evaluated regarding the location of the concentrator?s crushing, grinding, dewatering, process control and water systems. The energy cost comparison has been an important factor when evaluating the various choices. The single most important decision has been in choosing the grinding system. Once again the fully autogenous grinding system, favoured by Boliden, has proven to be the best solution. The location of the mill, high and near the tailing pond, gives lower transportation costs for the ore and tailings, compared to other locations. A new water system will lower the pumping cost, give better control of water circulation to the plant and create fewer problems with permafrost in the tailings disposal area. Molybdenum recovery will be installed in the new plant using a separate circuit. A gold leaching plant was also investigated. Gold leaching is planned for the pyrite concentrate from the chalcopyrite/pyrite separation and the concentrate from the desulphurisation circuit that will be installed on the bulk flotation tailings.

Jan 1, 2014

By E. V. Koporulina, E. L. Chanturiya, M. V. Ryazantseva, E. S. Zhuravleva

"The morphology of the surface of sphalerite, galena and chalcopyrite and the adsorption of butyl xanthate under conditions of preliminary treatment of minerals by the products of water electrolysis were studied using atomic force microscopy (AFM) and Diffuse Reflection Infrared Fourier Transform Infrared Spectroscopy (FTIR). It was determined that practically all types of treatment by electrochemically modified water (a product of non-diaphragmatic treatment, anolyte and catholyte) lead to an increase of surface roughness of the studied minerals due to formation of small rounded shape particles. In contrast to that, after treatment of chalcopyrite by anolyte, its surface becomes smoother. Various effects of treatment by the water electrolysis products on the adsorption of chemical and physical forms of butyl xanthate on the studied sulfides were established. As a result, the efficiency of the complex of AFM and FTIR methods, as one of the ex-situ approaches for monitoring the surface state of sulfide minerals and direct investigation of BKx adsorption products was demonstrated.INTRODUCTION In mineral processing, copper-zinc sulfide ores are one of the most complex products in view of their mineral composition, fine dissemination, complex inter-growth and the proximity of the technological characteristics of copper, zinc and iron sulfides. For the most complete disintegration, fine grinding of ores to a size of 0.074-0.044 mm is necessary. Consequently, the main method for processing of such ores is flotation, which bases on the difference in physical and chemical properties of the mineral surfaces, in particular, degree of wettability. The separation of copper and zinc minerals and their separation from ferrous and other sulfides, sulfosalts and rock mineral is a very difficult task (Chanturiya, 2000). For the successful separation of copper and zinc minerals in the appropriate selective concentrates, it is necessary to find conditions for the most complete liberation of ore and rock-forming minerals and for increase the contrast in physical and chemical properties of their surfaces. Despite significant progress in the processing of copper-zinc sulfide ores, the problem of the selectivity of the separation of the main ore minerals has not yet been fully solved and requires innovative approaches (Chanturiya, 2015). To date, various methods of preliminary energy processing of complex ores are used: magnetic pulse treatment, impact by high-voltage nanosecond pulses, electrochemical effects (including products of water electrolysis (Chanturiya et al., 2014; Bunin et al., 2015; Chanturiya et al., 2014a; Chanturiya et al., 2016), processing with flotation reagents, etc. Electrochemical treatment of water in various modes allows to obtain products of electrolysis with different oxidation-reduction properties: acid anolyte with a high oxidation potential and dissolved oxygen content, an alkaline catholyte with high reducing properties and a product of non-diaphragmatic treatment with enhanced reduction properties."

Jan 1, 2018

By B. H. Zhao

A low grade Pt-Pd ores, with 1g/t Pt and 0.13g/t Pd, and 8.70% Fe and 2.50% P2O5 is experimented to recover of Pt and Pd. The flowsheet is proposed which consists of Pt-Pd selective flotation, apatite flotation from tailings of Pt-Pd flotation, magnetic separation of magnetite from apatite flotation tailing. With butyl xanthate, N-ally group-O-isobuturyl-thioanimoformate and Sodium y-89 xanthate as collectors, sodium silicate as depressant, and sodium carbonate as pH regulator, a concentrate, assaying 324.52 g/t Pt and 45.62 g/t Pd, is obtained with recoveries of 87.23% Pt and 76.89% Pd from surface ore. A concentrate, assaying 1693.53 g/t Pt and 64.12 g/t Pd, is obtained with recoveries of 88.54% Pt and 83.78% Pd from primary ore. At same time, A iron concentrate assaying 64.12% Fe with a recovery of 24.94%, and a apatite concentrate assying 30.32% P2O5 with a recovery of 80.12% are obtained.

Jan 1, 2014

By Leming Ou, Longsheng Yi, Qiming Feng, Yiping Lu, Qing Shi, Kun Liu, Guofan Zhang, Yanfei Chen

"Three important components of stirred tanks involved in energy consumption, the impellers and baffles, were investigated to intensify the agitation pretreatment on the flotation of nickel ores. Flotation tests revealed that the stirred tanks with two impellers had an advantage over those with one impeller in intensifying agitation pretreatment, and the higher agitation speed led to better flotation performance of nickel ores. Installation and removal of baffles were also employed in the stirred tanks, and flotation tests demonstrated that with baffles, the flotation grade increased significantly. These agitator design improvements were used to demonstrate that the energy supplied to the system significantly influences the flotation recovery and that if the energy consumption of the agitation pretreatment is ideal, flotation efficiency can be improved. Data from full-scale operations backed up these results.INTRODUCTIONThe flotation recovery of nickel-copper sulphide ore at the Western China nickel mine has historically been difficult due to the presence of large amounts of serpentine minerals (Feng, et al., 2012). Many studies reported that serpentine minerals tend to have a positive potential at pH values up to 9.5, while sulphides (such as pentlandite and chalcopyrite) have a low isoelectric point(Feng, et al., 2012). Serpentine minerals can form surface coatings on negatively charged sulphides surface due to electrostatic attraction when they interact with each other, which may also reduce collector adsorption and increase the hydrophilicity of the sulphide particles. In order to improve the flotation of nickel sulphides, sodium hexametaphosphate, sodium silicate, carboxymethyl cellulose (CMC), and other agents are used to disperse serpentine coating from sulphide surfaces in the flotation of the Jinchuan deposit and other nickel ores in China ( Kirjavainen and Heiskanen, 2007; Lu, et al., 2011). However, it is difficult to improve of the sulphide flotation due to the high dosage and the lack of selectivity."

Jan 1, 2018

By Kumar Ranjan, Kumari A. V. Asha, G. E. Sreedhar, Banerjee R. Raja, M. Narasimha, R. Shivakumar

In this paper, numerical simulation of magnetite, medium segregation and coal partitioning have been made in a 350 mm diameter cyclone. An attempt is made to assess the nature of impairment in efficiency in relation to the increasing amount of near gravity materials in coal. The CFD model approaches the Algebraic Mixture (ASM) model with the granular option and Reynolds stress model (RSM) to resolve the air core and turbulent mixing of the medium and coal particles. The partition characteristics of the DMC were modelled using both Lagrangian & Eulerian particle tracking for particles ranging in size from 0.5 to 8 mm and in density from 1200 to 2000 kg.m-3. Lagrangian frame work based Discrete Phase model used to simulate the coal particle trajectories inside the DMC and attempted to understand the residence time of different size and density coal particles. It was observed that coal particles having density near to separation-density (having fifty percent of probability to under flow and overflow) are exhibiting increased residence time than any density particles. As expected the smaller size coal particles shows higher residence time than the coarse coal particles. CFD simulations on effect of NGM mass fraction are simulated and analyzed using ASM model including for coal and magnetite. Coal particles with high NGM content show significant effect in misplacement of coal particles towards wrong products at all relative densities. The residence time of the particles increases because of its increased interaction with near dense particles. The effect of NGM fraction on overall cyclone performance as well as detailed flow assessment in terms of residence time distribution, NGM particle concentration profiles with respect to LZVV is presented.

Jan 1, 2018

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014

By E. Barsky

Physical principles of two-phase flows with a polyfractional solid phase have not received a sufficient theoretical interpretation as yet. Two-phase flows in the separation mode with a counter-flow of particles are even more complicated. Only statistical methods give an insight into general regularities of such processes. These processes can be interpreted best by analogy with the statistical model of an ideal gas developed by L. Boltzmann, although here a number of difficulties arise. The notion of a statistical system for such flows is substantiated. A mathematical estimation of a statistical system is presented. New notions are introduced, namely, potential extraction of a system and lifting factor. A relationship having the physical meaning of entropy is derived for a two-phase flow in the separation modes. The connection of this new entropy with flow parameters, such as the number of particles, separation factor and chaotizing factor, is established. Properties of this entropy are analyzed, as well as the analogy and difference between this entropy and Boltzmann?s entropy. The notion is formulated and the definition of the chaotizing factor of a process is suggested. In the framework of a statistical approach to two-phase flows in the separation mode, the notion of flow mobility has been formulated. Principal regularities of mass transfer in zone/apparatus sys-tem are analyzed. Principal ideas of a cellular model of the process are formulated, and main relationships for its description are derived. Proceeding from the cellular model, a dependence describing the degree of fractional separation of a narrow size grade is found. The analysis of this dependence makes it possible to reveal the crucial role of the Froude criterion for gravitational separation processes. It is found empirically that this parameter is a basis for the affinization of separation curves (Barsky E, Barsky M, 2006; Barsky, 1980).

Jan 1, 2014

By R. S. Wang

The flotation of pyrite which be pretreated by electrochemical ways under external controlled voltages in different pH is explored. The floatability of pyrite is increased indistinctively after being pretreated in acidic and xanthate environment; Whereas, it is increased obviously between 400~800 millivolt in alkaline and xanthate condition. The reason for higher recovery of pyrite is that oxida-tion reaction, which results in S0 and S02, takes place on its surface, and that ethyl xanthate is oxi-dized into dixanthogen. In the meantime, the kinetics and mechanism is also studied.

Jan 1, 2014

By M. Kargar Razi

According to the unique properties and many applications of nano silver powder, it was prepared from acid leaching tail solution. The low value residual gold and silver ions were occurred with fellow heavy metals as pollutants (Fe2+, Cu 2+and Zn2+) in acid leaching tail solution in Mouteh gold mine in Iran. Preparation of nano silver particles was achieved in two steps: first, by addition of ammonia as separation step and second by using different reagents as precipitation and extraction steps. Different controlled parameters were including pH, residence time and temperature, mixing time, and reducing reagents to metals molar ratio. Acid leaching process was carried out with sulphuric and nitric acid via suitable reductants. In order to remove copper, zinc, and silver ions from solution, all of the conditions were controlled. The optimum conditions for preparation of nano silver powder with less than 90 nm were pH 10.5, hydrazine/methanol to silver molar ratio of 3 to 4, and reduction time of 5 min in 45 °C. The results were evaluated via SEM, A.A and UV- Vis spectroscopy analytical methods.

Jan 1, 2014

By E. Isokangas

The production of minerals for economic use is a two-stage process, involving mining to extract the mineral from the ground, and processing to convert the mineral into a marketable product. Generally, mining and processing have been viewed as self-contained entities. Both have separate objectives, separate cost centres and key performance indicators (KPIs) that do not reflect the customer/supplier relationships that inherently exist. However, mining and processing operations are inter-connected and therefore intimately inter-related with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often misses potential economic benefits and energy savings. During the past fifteen years, the authors have been involved in implementing a holistic methodology ?Mine to Mill Process Integration and Optimisation (Mine to Mill PIO)? to maximize the overall profitability of the operation rather than just optimizing any individual process in a mining operation. Metso Process Technology and Innovation (PTI), along with their project partners, have conducted several projects to significantly increase their production- generating typically 5% to 20% higher throughput and improve the overall mine and concentrator performance through PIO methodology. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG, HPGR or conventional grinding circuits. This paper explains the Mine to Mill PIO methodology and discusses the benefits of such an approach on the energy consumption, the overall costs and benefits of mining operations. The paper also summarizes several case studies illustrating the use of PTI methodology in a variety of applications. Keywords: integration, optimization, simulation, modeling, mine-to-mill, comminution, blast, drill, crushing, grinding

Sep 1, 2012

By D. Moradkhani

The objective of this research was, to evaluate the hazard of heavy metals in the soil around the National Iranian Lead & Zinc (NILZ) Company. In this study, 38 samples of soil around the NILZ factory were collected using standard sampling method, so that, the heavy metals Pb, Zn, Cd and Cr have been evaluated. The concentration of heavy metals were measured and compared with standard limits. The results show that the hazard of heavy metals in soil is not so serious and the content of Pb in just 5 percent of samples, and the content of Zn in just 3 percent of samples were above standard limits and the concentration of Cd and Cr were under the standard limits. Average, variance and standard deviation of the elements are calculated and with due attention to the standard deviation, Pb and Zn are seen to be more distributed than Cd and Cr. Also the isograde curve of heavy metals was drawn using software called Surfer. These curves showed that the heavy metals are concentrated at particular distances from the factory. Keywords: heavy metals, remote sensing, sampling method, isograde curve, Surfer software

Sep 1, 2012

By E. Szelag

The adsorption and stabilization of mineral dispersed systems by using Pluronic copolymers with different molecular weights and EO content has been studied. The role of sequential adsorption of EO-PO copolymers and cationic surfactant (CTAB) on the carbonate particle properties and in determining the stability of their suspension was studied with particular attention to the conformation of the polymer at the solid-liquid interface. The purpose of this work was to investigate the flocculation phenomena, influence of polymer molecular size on stability of suspensions of magnesite and dolomite and the effect of addition mode of polymer and surfactant. The suspension stability measurements and the determination of sedimentation speed were carried out using an optical analyser (Turbiscan). In most of investigated cases, the biggest floccs and the fastest sedimentation were found for low concentrations of copolymers.

Jan 1, 2014

By V. K. Gupta

Several approaches to the estimation of the size discrete breakage rate and distribution parameters (kj and bi,j ) of the batch grinding kinetic model are available in the literature. Analysis of a large amount of data available in the literature and our own data on several pure minerals and complex ores has shown that it is not always possible to obtain correct estimates of the two sets of parameters using known approaches as several widely different combinations of k and b parameters can sometimes simulate the batch grinding data reasonably accurately. It has been found that there are two main reasons: (i) all size classes are not well represented in the data and (ii) functional forms used for estimation of the two sets of parameters are sometimes chosen somewhat arbitrarily (especially in the case of complex ores), though they are actually uniquely related through size continuous breakage rate and distribution functions. A suitable experimental methodology has been described and demonstrated using some synthetic data and actual experimental data. A mill function approach, which does not require making any assumptions about the functional forms for k and b parameters, is also described and demonstrated. This approach is promising, but requires further development.

Sep 1, 2012

By Ji Hoe Kwon

Hindered-settling column process has been used for the separation of mineral particles for many years. In this study, a model based on DEM (Discrete Element Method) was used to simulate the movements of particles in a settling column separation process. DEM model is capable of describing the motion of particles and calculating the impact forces between particle and particle, and particle and wall contact under various operating conditions. Drag force, rotation induced Magnus lift force, contact force and the gravitational force acting on individual particles were considered for establishing the mathematic models. The overall motion of the particles in water is satisfactorily simulated by the DEM, and the result shows good agreements with the result of lap-scale experiment.

Jan 1, 2014

By Peter Kondos

The need for a sustainable development of ore deposits makes it imperative to be innovative and mindful in creating an economically and environmentally viable operation, while maintaining a good working relationship with the various stakeholders involved in developing and operating a large and complex mining project. This is becoming immensely important as gold ore deposits are becoming more mineralogically complex along with lower grades presenting both metallurgical and environmental challenges that need to be addressed in mitigating risks and improving project economics. This paper presents Barrick?s approach to development of strategic technologies for our long-term sustainable growth through conversion of valuable resources into reserves for both our green-field development projects and the expansion of our existing mining operations. Some of the key strategic solutions, including mineral processing, metallurgical and energy technologies, developed by Barrick and their impact on some of our complex gold and copper-gold ores will also be discussed in this paper. Keywords: gold ores, copper-gold ores, processing, breakthrough technologies

Sep 1, 2012

By A. Zangooi

Frothers play major roles in flotation through interaction at the air/water interface. A method of determining frother adsorption density (coverage), i.e., the number of molecules per unit of interfacial area of bubble surface, is introduced. The technique is based on mass balancing the frother around a continuously operated bubble column. The mass balance requires collection of bubbles before they burst. The column design and operating procedure is reviewed, and some preliminary results discussed. Keywords: flotation, colorimetric frother analysis technique, frother mass balance, coverage

Sep 1, 2012

By Nidhi Kumari

This work is based on surface chemical properties of bacteria during adaptation to high grade copper minerals and the projected consequences in Bio-Flotation process. The utility of bio-processing in the beneficiation of copper ore through bio-flotation is demonstrated. An autotroph Acidithiobacillus Ferrooxidans bacterium is adapted to high grade mixed copper ore sample by repeated subcultures. The surface characteristics were studies by analyses at different pH and time intervals. From the studies, it was established that the mineral-adapted cells became more hydrophobic as compared to unadapted cells during bio-flotation. It was also noticed that there was no significant changes in the surface charge of bacteria before and after adaptation. Keywords: bio-flotation, copper, Acidithiobacillus ferrooxidans, hydrophobic

Sep 1, 2012