Search Documents

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950’s and 60’s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining methods during and after this period led to that pneumatic devices being unable to treat run-of mine coals with the desired efficiency. Since the 1960’s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. This is the last operating dry coal dressing plant existing in Europe. The actual technical standard of dry coal dressing has been analysed during test-work and sampling in this plant (Saar Region in Germany). The process and the advantages and disadvantages are presented. The plants problems are low efficiency in the fine fraction –6 mm and the coarse fraction +30 mm and a low overall throughput as well as the lack of an automatic process control system. The separation results in the medium size fractions between +6 and -30 mm are excellent"

Jan 1, 2003

By Mary Stewart, Jim G. Petrie, Geoff Brent

"Life Cycle Assessment (LCA) is gaining increasing acceptance as a decision-support tool by which to evaluate the environmental performance of a product, process or service. This is evidenced by its inclusion in international policy documents (for example in the European Union’s Integrated Product Policy) and in environmental management standards (the ISO 14 040 series of environmental management codes relate to LCA). In response to this, the minerals industry has conducted a number of commodity-specific LCAs. These include studies for global production of a number of commodities including copper, nickel, aluminium and steel. In addition, a number of minerals companies profess to use LCA as part of their suite of project and technology assessment tools. Often, this collected use represents more a situation of “we do this because we’re told it’s good for business” rather than from any demonstrable evidence of this fact. This has led to a situation of much confusion and disillusionment within the industry, exacerbated by the obvious current limitations of LCA to accurately reflect the environmental performance of minerals and metals.Our point of departure here is that LCA, conforming as it does to the tenets of environmental systems analysis, is a valuable starting point, and that there is merit in exploring to what extent the methodology can be enhanced to better reflect the environmental performance of minerals and metals. Specifically, we explore here the further development of LCA to address the following:• Land Use issues• Consumption of Abiotic Resources including metallic and non-metallic minerals, water and soil)• Human and Eco-toxicity issues relating to mobility and bio-availability of metals• Salinityand address these through selected experimental and simulation case studies relating to energy- and base minerals production. Advances resulting from the United Nations Environment Programme/Society for Environmental Toxicology and Chemistry Life Cycle Initiative are presented in that they directly affect the application of LCA to mining, minerals and metals. Comments are offered on how best the mining and minerals industry might interface with future developments resulting from this Initiative in order that the Initiative can deliver outcomes which render LCA a useful tool for decision making in mining and minerals processing."

Jan 1, 2003

By Malcolm Mudge

"One of the oldest mining areas in the World exist in Africa and the Middle East. This area is being exploited by foreign and local mining entities. Several large plants, both foreign and local as well as small operators, conduct their mining business on a scale which would be could be prohibited in any other part of the world. Relatively recent European disaster with tailing disposal and breakout has highlighted the problem.More important to the author is that the presence of foreign entities in zones which have not remedied the situation but has heightened the concern due to those entities using similar outrageous methods in treatment of waste. The abject misuse of technology cannot be permitted to continue and the lack of any metallurgical knowledge in the treatment of gold ores is considered deplorable for the majority of third world countries.The destruction of cyanide is simple and straightforward and requires no special skills. In South America, we developed a system that is modular, compact and can be operated in batch mode to cater for several clients, as required. Larger installations would require a separate module, as treatmentwould be on a continuous basis."

Jan 1, 2003

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of rgrinding conditions on galena flotation and galena separation from pyrite. The various reactions occurring on the mineral surface were investigated by a range of techniques, including OH- addition to maintain the grinding pH, EDTA extraction, XPS and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the metal oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite but had little effect on galena. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled."

Jan 1, 2003

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data – especially with semi-automated data acquisition by instrumented mine equipment. Much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together – in a single step. However, the success of the Mine to Mill ™ project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measured data and then to track performance from ore body model to saleable product and waste disposal.The path from resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is usually strongly focused on the technical requirements – not on the business model.This paper emphasises the difference between data and information. There is considerable potential for confusion between the two as both data and information are often expressed as numbers. For the purpose of this paper, data and information are distinguished by their uses.A data point (or datum) is a measurement. By way of contrast, information provides a basis for decision making."

Jan 1, 2003

By Kauko T. Ingerttilä, Jouko O. Kallioinen, Jaakko O. Leppinen, Alexander V. Lashkul, Vladimir E. Nenno

"Separation in Froth (SIF) is a process for the separation of mineral particles during their descent downwards through a moving froth layer, generated on the surface of water or some other liquid media by means of a bubble generator and frother. Due to the special operation principles of SIF it is possible to separate mineral particles that are about 10 times coarser than the optimal particle size for conventional flotation. In this paper the performance of the SIF technique is presented in the separation of apatite, calcite and silicate minerals from various industrial sources, based on tests with laboratory and pilot plant-scale SIF machines. Basic laboratory test results of the flotation of pure diamonds are also presented.It was shown that calcite, apatite and diamonds with particle size up to about 3 mm can be successfully floated with SIF at high recovery and grade, provided that the degree of liberation is sufficiently high. Coarse calcite (+0.25-2.8 mm) was concentrated with reverse SIF in one flotation step at 87% recovery with better than 99% grade. Apatite particles coarser than 0.2 mm are not well floated in the conventional flotation circuit leading to high P2O5 content in the coarse size fractions of flotation tailings. On the contrary, SIF is capable of recovering such coarse particles at high recovery. However, P2O5 content of the SIF tailings starts to increase at about 0.7 mm due to insufficient liberation of apatite. At higher particle size the lack of hydrophobicity of apatite particles is also likely to lower the recovery.The pilot plant testwork showed that SIF can be successfully used at operating plants not only for preliminary upgrading of the feed of conventional flotation, but also for producing final grade calcite concentrate (>99.5%) from the screen overflow or from the cyclone underflow in a particle size range up to 1 mm. It was particularly promising that the separation took place in one SIF flotation step, instead of several stages of the conventional flotation circuit, with over 90% calcite recovery. The specific capacity determined with the 1 m2 pilot plant unit was approximately 30 t/m2h. Simultaneously the consumption of chemicals was significantly lower than for conventional flotation."

Jan 1, 2003

By Susanna G. de Jager, Francis W. Petersen

"To enable the prediction of reagents suitable for fine coal flotation, it is necessary to develop a methodology applicable to different South African coal types. Statistical confirmation of the applicability of this methodology is important to avoid recommendation of reagents on a trial and error basis.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements. Flotation tests were used to validate expectations from the characterisation of the coal samples.RESULTSThe flotation data indicated that all of the coal samples were amendable to froth flotation. The best results were obtained with the Witbank seam 2 coal and the poorest flotation with Syferfontein seam 5 coal. The flotation tests showed that the best reagents to float all of the coal samples studied were iso-decanol and dodecene. These reagents produced flotation products that were near to the release curve, which are the optimum flotation results (obtained when using iso-paraffin as collector). Dodecene resulted in low ash products and iso-decanol in high yield products."

Jan 1, 2003

By Wantae Kim, Hoon Lee, Kwanho Kim, Sangbae Kim

Mechanochemical activation of starting minerals and their effect on the solid-phase synthesis and properties of ceramics with lower thermal expansion coefficient was examined. The mineral mixture, pyrophyllite-gibbsite-lithium carbonate, was prepared for the synthesis of ?-eucryptite (Li2O•Al2O3•2SiO2). Dry grinding using a planetary ball mill promoted the amorphization of the starting mixtures. XRD and FT-IR results showed that the crystallization of the target materials occurred from the ground mixtures by calcination. The crystallization of them increased with increment of grinding time and calcination temperature. In the synthesis, the trace of undesired phases such as quartz and cristobalite once formed during calcination at the temperature range from 750 to 850 °C almost disappeared and monophase ?-eucryptite was formed in the ground mixture at 950 °C. The lowest liner thermal expansion coefficient (TEC) of ?-eucryptite prepared was -2.5x10-6•°C-1. The thermal expansion behavior characteristics of the calcined

Jan 1, 2014

By Leon Lorenzen, Charlene Gokhale

"In excess of 24 x 106 tons (Eskom, 1997) of coal-derived fly ash is produced annually in South Africa for the production of electric power. A large quantity of this ash is disposed of as a solid waste in landfills, thus posing a serious environmental problem. Due to the shortage of landfill sites, new ways of utilising fly ash are needed. Recently several authors have shown that various combustion fly ashes can be converted into zeolites to obtain industrial products with applicability in environmental management. Geopolymerisation has emerged during the last few years as a possible solution to some waste stabilisation and solidification problems. henolic compounds have been shown to be toxic to soil microorganisms at the parts-per-million level. Indeed several of the organic compounds classified by the U.S. Environmental Protection Agency as priority pollutants, are phenols. Immobilisation of phenols by adsorption on zeolites and encapsulation in a geopolymer appears to be a promising solution to this problem.This paper reports a technique for the production of a low-silica sodium zeolitic material from fly ash (zeolite NaP1), and its application for the stabilisation of phenols by adsorption and subsequent encapsulation in a geopolymer matrix. A commercial zeolite, clinoptilolite was also utilised as an adsorbent. Due to their uniform pore sizes and large surface areas, zeolitic materials are suitable for ion exchange and adsorption of certain organic substances. Adsorption data show that the commercial zeolite, clinoptilolite was an effective adsorbent for organics. Adsorption data showed that between 51.2 ppm and 74.3 ppm of chlorophenol or between 15.4 ppm and 32.5 ppm of phenol could be adsorbed. Physical encapsulation of the coated zeolite loaded with organic within a geopolymeric matrix increased the compressive strength of the matrix from 28.80 kN to 40.79 kN. Leaching data for the various geopolymer matrices with encapsulated and loaded zeolites show no organics being leached from the system at a detection level of 2ppm. According to the SABS these would have been acceptable organic concentrations within a waste water stream."

Jan 1, 2003

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Lee Jae-Jang, Park Chong-Lyuck

"Graphite has unique properties such as high thermal resistance, low thermal expansion coefficient, and good thermal and electrical conductivity, and is often utilized as coating materials for electrical conductors, TV Brown tubes, electromagnetic shields, and so on. Additionally, its excellent lubrication property is widely used in oil and solid lubricants. Finely ground graphite particles in the sub-micron range are commonly used for these applications.Sub-micron fine graphite particles are typically prepared in liquids by vibration ball mills. However, it is known that the wet process takes long periods of grinding time like 24 hours or more and requires a series of subsequent highenergy operations such as de-watering, drying, regrinding and classification. On the other hand, there would be numerous advantages if fine grinding could be done effectively in dry atmosphere. However, since crystalline graphite has a layered structure giving a high lubrication property, its dry grinding, especially when obtaining sub-micron size particles, is extremely difficult. The shape of the graphite particles is also important for its utilization since particles with flaky shape can maintain relatively high electrical and thermal conductance as well as lubrication ability. Therefore, it would be necessary to reduce the size of graphite particles into fines with flaky shape while grinding proceeds. Dry grinding characteristics of natural graphite under various atmospheric conditions with gases using different mills were studied, and fine flaky particles by grinding the graphite intercalation compounds and the exfoliated graphite were produced. However, there were no sufficient investigations on the size reduction of natural graphite at low atmospheric pressures in attritional milling conditions. The main purpose of this paper is to provide sub-micron fine grinding characteristics of natural crystalline graphite at various degrees of low atmospheric pressure, and to discuss the size reducing models in an attrition mill"

Jan 1, 2003

By A. V. Nozhkina

"Transformation of diamond into graphite was investigated in the region of diamond metastability under the action of media chemically active relative to carbon in the temperature range from 770 K up to 2200 K and pressure range from 10-3 Pa up to 3 GPa/IV VIII group metals of periodic system and oxygen were used as media chemically active relative to diamond.Methods of electron diffraction, chemical analyses, emission spectroscopy and X-ray phase analyses were used for determination of the reaction products.It was found that in the region of diamond metastability the stage of catalytic phase transformation of diamond into graphite took place during the interaction between diamond and metal. Metal reduce activation energy for transition of diamond into graphite from 109,4 kcal/mole to 77,4 kcal/mole.Kinetic of phase transformation of diamond into graphite was investigated.Pressure does not considerably influence on the rate of phase transformation of diamond into graphite in the presence of transition metals."

Jan 1, 2003

By E. Barsky

"The aim of separation is to obtain two products that are as distinct as possible from each other. It is currently believed that the most objective criteria for the quality of a separation are the Hancock criterion and the entropy criterion.1. Hancock criterion:- for yield of fine product"

Jan 1, 2003

By Rob D. Morrision, Paul W. Cleary

"The best accepted method for design of autogenous and semi-autogenous mills is to carry out pilot scale test work using a 1.8 m diameter by 0.6 m long pilot scale test mill. The load in such a mill typically contains 250,000-450,000 particles larger than 6 mm, allowing correct representation of more than 90% of the charge. This scale of DEM model is now within the practical range of standard workstations running an efficient DEM code.This paper describes various ways of extracting collision data from the DEM model and translating it into breakage and wear estimates. Account is taken of the different breakage mechanisms (impact and abrasion) and of the specific impact histories of the particles in order to assess the breakage rates for various size fractions in the mills. These impact histories have the potential to be directly related to breakage as they most resemble the single particle breakage tests which are used by the JKMRC to calibrate more traditional population balance models for variations in ore behaviour. However, the specific impact histories also show a background of many low energy collision events within the mill. This Background may constitute what is usually regarded as “abrasion” breakage. As might be expected, high impact events are concentrated in the toe of the charge and near to the mill shell where the forces associated with the load bearing on each particle is more concentrated."

Jan 1, 2003

By Tamara F. Kondrateva, Evgenia E. Savari, Galina V. Sedelnikova, Rauf Y. Aslanukov, RAS (INMI), Grigori I. Karavaiko

"The investigation is dedicated to study of biohydrometallurgical processing of refractory gold-arsenic concentrate with the large content of pyrrhotite. Sulfide concentrate of chemical constituents: 75g/t Au, 4,7g/t Ag, 6,3% As, 29,3% S, 2,3% Sb, 0,5% ? (organic) and of mineral composition, %: 11,8 arsenopyrite, 39 pyrrhotite, 12 pyrite, 2,9 antimonite and the rest – aluminosilicates, carbonates and quartz, was studied. The recovery of gold from concentrate by cyanidation is 51,2%. The rest of gold is embedded as finegraded segregation in sulfides.Sulfide oxidation process study is described. Bacterial oxidation was executed on a pilot laboratory unit using combined autotrophic bacterium: A. thiooxidans , A. ferrooxidans, Leptospirillum ferrooxidans and sulfobacillus thermosulfidooxidation, pH=1,5-2,2, t=28-32?C, oxidation time 120 hours. Pyrrhotite is the least stable sulfide mineral with electrode potential 0,45V versus arsenopyrite (0,55 V) and pyrite (0,55-0,6 V) and is oxidated primarily. Pyrrhotite oxidation is followed by large amount of elemental sulphur, which has a bad influence on cyanidation.It’s established that the rate of arsenopyrite (for the first 48 hours) from concentrate containing 39% pyrrhotite is 2-3 times as less as the rate of arsenopyrite bio-oxidation from concentrate without pyrrhotite. The arsenopyrite bio-oxidation is accelerated only after the elemental sulfur was oxidized by bacterium A. thiooxidans and elemental sulfur percentage was reduced from 6,8 to 3,9%. The bacterium concentration is increased from 2,5x107 to 2,5x109 cells/ml. Almost full oxidation of arsenopyrite (98%) and pyrrhotite (98- 99%) is finished in 120 hours. We have studied two pretreatment methods for elimination sulfur content influence on cyanidation: aeration in lime and electrochemical treatment. Such an operation enables to have supplemental oxidation of elemental sulfur and other oxygen and cyanide absorbants before cyanidation. After treatment the content of elemental sulfur was decreased from 3,9 to 2,2%, gold recovery from 90 to 96% and cyanide consumption from 16,2 to 7,2 kg/t decreases. The content of toxical rhodonite-ions in liquid phase of pulp and disinfection reagents consumption were decreased as result of elemental sulfur content in bio-oxidated product reduction."

Jan 1, 2003

By L. X. Yu

As is known, the oxidized antimony and antimonate are hard to treat. A new combined mineral processing flowsheet which is controlled in grinding and classification ?bulk floatation?gravity separation is adopted to dispose of gravity-separated tailings (antimony content: 1.48%; oxidization rate: 68.92%) in Muli Antimony Mine, the grade of floatation antimony concentrates is 32.64%; the grade of gravity-separated antimony concentrates is 26.99%; the combined grade of floatation and gravity-separated antimony concentrates is 30.85%, and the total recovery of antimony is 70.64%. Adopting the new mineral processing technique have solved the problem of over grinding of antimony ore by controlling grinding and classification, recovering effectively the sulfide antimony and the easy floatable oxidized antimony of fine size by bulk floatation, recovering effectively the oxidized antimony which is hard to float by classified gravity separation. This is a great breakthrough in the mineral processing technique of the recovery of the oxidized antimony. At present, favorable economic benefit has been obtained from the application of this processing technique in Muli Antimony Mine.

Jan 1, 2014

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

"Different hydrometallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2 (Vegliò and Toro, 1994). An innovative acid reductive leaching carried out in soft experimental conditions was here considered using agro-industrial wastes containing carbohydrates as reducing agents (Vegliò et al., 1998).The leaching process was investigated from a kinetic and equilibrium point of view in order to optimize the experimental conditions and obtain high purity and concentrated MnSO4 solutions.The overall leaching process (not considering the complex network of intermediate oxidation reactions of the carbohydrates in hot sulphuric acid medium (Vegliò and Toro, 1994)) can be described by the following reaction:24 MnO2 + C12H22O11 + 48 H 24 Mn2+ + 12 CO2 + 35 H2O (1)A Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis and BET surface measurements before and after leaching.Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydroalcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions."

Jan 1, 2003

By J. Tian

"BHP Billiton carried out a pre-feasibility study on the LanPing zinc deposit to evaluate the possibility to jointly develop the zinc deposit into a large-scale zinc project with their Chinese partner. The unique characteristics of the complex LanPing zinc orebody and ore are 1) smithsonite (ZnCO3) as one of major zinc bearing mineral besides sphalerite, 2) varying and irregular oxidation degree of zinc (0 ~ +90%) in the different zone and depth of the deposit, and 3) varying host gangue from limestone/calcite dominant to quartz dominant, which requires a robust and flexible flotation process to recovery zinc from both sulphide and oxide efficiently.The conventional mineral processing flowsheets have been tested on the LanPing samples taken from the various orebodies by various parties during the past 20 years that includes a sequential flotation flowsheet that was tested in a demonstration plant using the mixed ore. The results of the demonstration plant runs show that the conventional oxide flotation using Na2S and amine collectors could achieve 50 ~ 75% of oxide zinc recovery at very high sulphidiser consumption for the mixed ore but the highly oxidised ore did not satisfactorily respond to the flowsheet in terms of performance consistency and efficiency of oxide zinc recovery, which is very crucial to the overall economics of the project."

Jan 1, 2003