Search Documents

By Takefumi Takuma, Ali Fayad, Shigeru Kambe

"This paper discusses the unique design and construction circumstances of the cantilevered dual sheet pile walls and the Accordion Sheet Pile Wall for the repair and upgrade of the East Garden Grove-Wintersburg Channel in Huntington Beach, California that was concluded in 2014. It also describes the 2008 Emergency Sheet Pile Project for the same channel. Both projects utilized the Press-in Piling Method for its low noise and almost no vibration advantages.BackgroundThe East Garden Grove-Wintersburg Channel is part of the Orange County Flood Control District (OCFCD) and is operated and maintained by OC (Orange County) Public Works (see Figure 1 for its location). The channel, referred to as OCFCD facility # C05 (C05), had suffered significant toe undercutting and slope erosion of its levee due to a series of storms. These began after the facility was constructed in the 1960’s and culminated in 2005. Consequently, the levee was deemed significantly deficient and was eventually declared as a local emergency in 2007. C05 was an incised channel and its levee was constructed primarily from native materials. Operation and Maintenance (O&M) personnel notified the design staff at OC Public Works to be aware of major consequences associated with the dilapidation problem in the most downstream reach of the channel in the vicinity of the Bolsa Chica Wetlands Restoration Project. In 2007, the Orange County Board of Supervisors declared a local emergency to fix the levees with sheet piles to be driven by the Press-in Piling Method, hydraulic pushing piles into ground by holding onto previously installed piles. The project that ensued represented the first in-tandem use on the West Coast of the United States of the Press-in pile driver with its GRB System (Press-in pile driver, a support crane and pile transporter travel on top of already-driven sheet piles). This is further discussed in this paper in the sections titled “Press-in Piling Method” and “GRB System”, respectively. The project repaired approximately 3,800 feet of erosion on the north levee of C05 with 45-foot long cantilevered sheet piles. The sheet piles design constraints are discussed in this paper in the section titled “C05 2008 Emergency Sheet Pile Project (Phase 1)”. Between 2012 and 2014, another mile’s worth of levee reach was improved with the Soil-Mix-Sandwich (SMS) Method. This concept consisted of deep soil cement mix (DSCM) columns sandwiched within the dual rows of sheet piles. Additional details on the SMS, its DSCM construction, and its hybrid geo-structure design concepts are well beyond the scope of this discussion, which is primarily focused on sheet piles. Instead, the interested reader is referred to two papers on the SMS and its DSCM metrics (Fayad, 2015; and Arora, et al., 2015). These were presented and published in the Proceedings of the Deep Foundations Institute (DFI) 2015 Conference on Deep Mixing. Hence, in the section of this paper titled “C05 SMS Dual Sheet Piles Project (Phase 2)” only the sheet pile design constraints of the SMS are covered. Finally, in the area where the project traversed the Alquist-Priolo zone of the Newport-Inglewood tectonic fault, an expandable and deflectable sheet pile wall was used to isolate the flood channel from the Bolsa Chica wetlands. Its details are addressed in the section titled “C05 Accordion Sheet Pile Wall (Phase 2)” of this paper."

Jan 1, 2017

By Edmund Cardoza

In the spring of 1993, construction began on an ambitious building project in Boston, Massachusetts. The Shriners organization committed to offer state-of-the-art adolescent burn treatment and rehabilitation in its Boston facility by expanding in a most unusual way. In short, the concept included installation of caisson foundations and perimeter slurry wall panels to enable construction of a completely independent structure around and above the existing, continually functioning, hospital. Two distinct phases of work were detailed in the Contract Documents. At the completion of the first phase, patients will be moved into the new building, above, and demolition of the old structure, beneath, will be performed. In Phase I, sections of the slurry wall and caissons, located outside the footprint of the existing building, were planned. The next phase of the work includes the installation of the remaining caissons and slurry wall. Once excavation is completed, the balance of the new hospital structure will be constructed from the bottom upward, connecting to the under side of the new structure.

Jan 1, 1994

By Hyun. I. Park

Although numerous investigations have been performed over the years to predict the behavior and bearing capacity of piles, the mechanisms of these behavior and bearing capacity of piles have yet to be entirely understood. Bearing capacity is difficult to predict, because it is affected by many parameters, which have complex relationship with each other. The present paper describes the application of Artificial Neural Network (ANN) in dynamic load tests to predict the resistance of driven piles. The tip, shaft, and total pile resistances can be predicted only for piles with available corresponding measurements of these values. The design methodology composed of ANN and genetic algorithm (GA) is applied to find the optimal neural network model to predict pile resistance. The results of this study indicate that the neural network model serves as a reliable and simple tool for predicting the capacity of driven piles.

Jan 1, 2006

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Cheng Lin, Guoming Lin

"This paper presents a case history for the design, construction and long-term performance monitoring of a driven prestressed concrete (PSC) piled foundation supporting a large liquefied natural gas (LNG) tank in Savannah, Georgia, USA. Following a geotechnical investigation, a design stage pile test program was performed with three objectives: to study the densification effect from pile driving on the liquefaction resistance, to test axial and lateral pile capacities, and pile behavior under lateral loads. The test program comprised five piles driven on a test pad constructed adjacent to the tank foundation. Cone penetration testing (CPT) was performed before and after pile installation to test soil densification effects from the pile driving and liquefaction potential was re-evaluated based on the soil densities after pile installation. The axial load tests involved static load testing, high strain dynamic testing, and Statnamic testing. This paper presents the findings of the densification effects, compares results from different axial testing methods and discusses the procedures to use the load test results in the pile design. The paper also comments on the construction issues and presents performance data with 10 years of monitoring.1. IntroductionThe project site is located at the Kinder Morgan’s Elba Island LNG Terminal on the Savannah River which is three miles downstream of the downtown Savannah, Georgia. This LNG terminal was initially developed in the 1970s as an LNG import terminal. The facility includes five LNG storage tanks with two larger tanks which were constructed in 2003 and 2006, respectively. The terminal is currently being converted into a liquefaction and export facility. This paper discusses pile foundations for Tank D4 which is a double walled insulated steel tank built to hold one million barrels of LNG in 2003. This tank has an outer tank diameter of 258 feet, an inner diameter of 252 feet, and liquid height of 113 feet. A number of geotechnical challenges were present in the foundation design and construction.??The site is a typical coastal deposit site featuring a thick layer of very soft under-consolidated clay (up to 40 feet in thickness);??The bedrock is a couple of thousand feet deep;??There is a sand layer that is liquefiable under a high seismic design category (0.5% possibility of exceedance in 50 years)."

Jan 1, 1900

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Alp Gokalp

The aim of this article is to present an application of jet grouting technique in stiff clays for foundations of the natural gas combined cycle power plant, under construction in Aliaga, Turkey. The plant site is in the Aegean coastal region and 60 km north of Izmir. The foundation soil is composed of quaternary alluviums on top and tuff base rock. The thickness of the alluvium varies between 16 m to 30 m. Groundwater was observed 2.5 m below the ground level. At the design stage, settlement analyses were carried out for the various buildings and facilities in the power plant. Based on the analyses, it was predicted that total and differential settlements are not tolerable, thus jet grouting is implemented as a ground improvement under the majority of the foundations of the power plant. This paper also describes the selection of jet grouting technique, application type and details of the process parameters such as injection pressure, number and size of nozzles, lifting and rotation speeds. Prior to the commencement of the jet grouting works, a number of preliminary parameter tests and preliminary pull-out tests were carried out throughout the site in order to define and verify the jet grouting process parameters to achieve the required diameter of 600 mm and minimum jet grout strength of 3.2 MPa. Moreover as part of the comprehensive quality control and quality assurance program pursued in the project, a number of tests; such as continuous coring, integrity testing, installation of confirmatory jet grout columns, were carried out during the production of jet grout columns.

Jan 1, 2002

By Nick O’Riordan, Kaitlyn L. Fleming, Michael Riemer, Youssef M. A. Hashash, Stephen McLandrich, Mohamad Jammoul, Pierre Gouvin, Andrew Yeskoo

"To accommodate urbanization, cities are developing more underground space as a means to house public transportation systems and other entities. Underground developments often require construction of deep excavations in an environment dense with infrastructure. The success of such a project is related to the amount of impact imposed on adjacent structures and economic activity; impact should be limited to insignificant amounts in order to mitigate damage and disruption. Thus, large-scale urban construction projects require extensive monitoring of ground movements and installed support performance to facilitate informed decisions for adjustment of construction activities and support design when necessary.In downtown San Francisco, a unique large-scale excavation in saturated soft soils was constructed for the Transbay Transit Center (TTC). Construction of the excavation began in April 2012 and was completed almost two years later in February 2014. To monitor ground and structure response to construction, the project team used an extensive instrumentation network that included automatic inclinometers, piezometers, strain gages and total stations paired with survey markers. Innovative imaging techniques developed a record of construction in order to relate measured deformations to construction activity.Transbay Transit CenterThe Transbay Transit Center (TTC) is being constructed as a modern day transportation hub in downtown San Francisco to replace the former Transbay Terminal. The project is located in the South of Market area, less than half a mile from the San Francisco Bay. The final center will connect eight counties in the Bay Area through 11 different transportation systems, some of which will be housed in the TTC including Caltrain, Golden Gate Transit and California High Speed Rail. The aboveground structure will consist of two levels for retail and a third level with a bus terminal beneath a rooftop garden. There will be two subgrade levels to serve as a lower concourse and the train platforms. This structure required construction of a deep excavation closely surrounded by buildings and roads in an area thriving with economic activity."

Jan 1, 2015

By Clif Kettle

The paper will detail the design and execution of passive and active settlement control measures, the means adopted to overcome the various physical and operational constraints, and to meet specified allowable settlement criteria. The paper will highlight the close integration between the tunnelling and geotechnical contractors, designer, and Client, and demonstrate how particular practical difficulties were overcome by both the design and the construction methods.

Jan 1, 2008

By Ken MacLeod

A development at 83 Queens Road in Melbourne, Australia required construction of a three level basement. The normal geotechnical constraints of excavating adjacent to an existing relatively new building were challenging enough for the complicated soils profile occurring at the site. An additional significant challenge faced by the designers, was the requirement to excavate underneath the entire footprint of an existing heritage listed building, known locally as the Mansion, in the centre of the site. Maintaining the structural integrity of that building was afforded the highest priority during the 10m excavation. This paper describes geotechnical aspects of the analysis, design and construction of the secant retention system adjacent the new building and support of the Mansion enabling the 10m excavation to proceed without causing damage to the structure. The secant wall comprised hard-soft interlocking piles constructed using CFA methods. CFA piles along the length of the Mansion provided short term support, with the building load being transferred to the piles by large steel beams jacked under the building. Survey results confirmed that movements of the retaining wall and also the load bearing piles were minimal and well within design expectations.

Jan 1, 2006

By Walter Kaeck

In a recent upgrade of their system, Amtrak converted a bascule type draw bridge over the Thames River to a vertical lift structure supported by the existing piers. During the bridge replacement, significant settlement occurred on one of the piers and movement continued thereafter. Construction was stopped as Amtrak became concerned as to how much the subsequent construction activities would cause the pier to further settle and tilt, not only impacting the operation of the existing bridge, but also jeopardizing the new lift span. Mueser Rutledge was engaged at this time to help understand and solve the problem. A remedial grouting program was developed to arrest the settlement. As a subcontractor to Cianbro Corporation, Pittsfield, ME, The Judy Company was hired to perform the remedial grouting work. Work platforms were constructed around the pier for support of the drilling equipment. A dual string drilling system was used to install sleeve pipes at depths of up to 185? below the water level. Ultrafine cement grout stabilized with additives was placed at 2.5 foot intervals through the depth of the sand and gravel stratum below the bottom of the pier. Logistics were difficult and the schedule was severely impacted by the remedial work, necessitating working six 12-hour shifts per week and working in the river through the winter months. After four months of drilling and grouting, movement of the pier stopped. At the conclusion of the remedial work, more than a million gallons of ultrafine cement grout were placed. Confirmation borings recovered completely solidified material with compressive strengths ranging from 500 to 1500 psi. The bridge replacement was then completed and is functioning. Continued monitoring through July 2009 shows negligible movement.

Jan 1, 2009

By Kenton W. Braun

Concourse B at the Anchorage, Alaska International Airport is currently being renovated while retaining the original building structure and foundations. Part of the renovation includes the installation of a new, permanent baggage tunnel system beneath the existing building. Installation of this cast in place concrete tunnel, beneath the existing structure, required installation of a steel retaining wall to support footing loads above the base of the excavation. Construction of this retaining wall presented challenging and unconventional design and construction methods. Detailed discussions of the design and construction techniques utilized for this project are outlined.

Jan 1, 2008

By Rob Jameson

Micropiles are ideally suited to seismic retrofit applications. Their high tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. Micropiles can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones, using equipment that operates effectively within existing structures. Micropiles have seen increased acceptance and are now widely specified for retrofit work in the San Francisco Bay Area. While installation equipment and the structural configuration of micropiles have been largely unchanged since the early 1990?s, market forces have pressured both engineers and contractors to continually optimize the cost and performance of seismic upgrades. Instead of the contractor simply developing stronger, stiffer and cheaper micropiles as isolated structural elements in response to a specification, focus has shifted to maximizing the efficiency of micropiles within the overall foundation system. The case history of seismic retrofit project in Berkeley, CA is presented to illustrate the collaboration between designers and drilling specialist which resulted in a structurally efficient and cost effective design. The seismic retrofit program for this 6-story concrete building was developed through careful consideration of the geotechnical and structural mechanisms of resistance, in combination with the deformation response of high capacity micropiles (2670 kN) under ultimate loading conditions. This case history describes the interactive project development emphasizing performance-based design and field testing to optimize the micropile foundations and the overall structural system.

Jan 1, 2008

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the ?strong? rock stratum, but did not correlate well with the design value calculated for the ?weak? rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2013

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner&apos;s engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel&apos;s observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile&apos;s geotechnical and structural design, and the contractor&apos;s pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Prof. Dr. -Ing. habil. Sascha Henke, Johannes Beck

The growth of Building Information Modeling (BIM) during recent years opens possibilities for integrating new digitally driven design approaches. While parametric design and algorithmic design slowly gains popularity in numerous ACE-applications, e.g. bridge design, it is rarely used by geotechnical professionals. This article presents an approach for implementation of parametric design in the BIM-based geotechnical design process. The methodology is applied to pile design and enables a real time design analysis according to DIN EN 1997-1 and EA-Pfähle 2012 considering boundary conditions such as pile position and layout, pile geometry, soil stratification and soil properties. By using intelligent attributes and scripts to control, calculate and assign them, the design analysis is directly executed in the BIM-software environment, in this case Autodesk Revit with Dynamo. This BIM integrated design approach allows multi-criteria evaluations of pile designs using aspects such as costs, environmental impact or constructability in addition to the commonly examined structural analysis criteria. As the proposed models are fully parametric, generative optimization algorithms can be applied to identify the ideal design for the entirety and each of the piles. Finally, the potential and limits of this methodology with respect to modeling, analysis, simulation and optimization are discussed.

May 1, 2022

By S. Y. Fantaye

This paper discusses the design, construction and performance of a 30 inch thick diaphragm wall recently constructed in Baltimore, Maryland at Inner Harbor East. The project site is an established marina and waterfront property. The geologic profile consists of fill, alluvial silt and clay, Potomac sand and clay, decomposed rock, and weathered rock on top of gneiss bedrock. The approximately 1,300 ft long perimeter diaphragm wall serves as a water cut-off, perimeter basement wall and support of excavation for the high rise project?s five levels of below-ground parking. Due to the fast track construction and the tight schedule, the initial design of the diaphragm wall was based on a limited amount of geotechnical information. Supplemental borings were then performed along the alignment of the wall to verify the design assumptions and wall depths. Additionally, the design criteria required that the wall be keyed into a competent stratum with low permeability. The Engineer of Record for the diaphragm wall, Mueser Rutledge Consulting Engineers (MRCE) completed the design and produced accelerated construction documents allowing the developer to release the drawings early for bid. This paper describes the theoretical soil parameters used to develop the loads, moments, and shears for the design of the diaphragm wall and the temporary tieback anchors. It also discusses the refinement of these soil parameters using the observed wall displacements and tieback pre-stressing forces as a baseline. This paper compares the calibrated parameters to the values used in the design of the wall. It explains how the soil structure interaction model was developed and the soil parameters calibrated using PLAXIS 2D non-linear finite element software. The paper also discusses the use of the proprietary CWS joint by Soletanche/Inquip JV as end stop between consecutive wall panels and the unique top-down construction utilized to support the diaphragm wall at the Southeast double re-entrant corner.

Jan 1, 2008

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Brad W. Taylor

"During the past several months, I have introduced to civil and structural engineers an innovative solution for the integrity testing of concrete using the Thermal Integrity Profiler (TIP) Wire Cable System by Pile Dynamics. While in the process of “educating” highly-trained professionals about a technological breakthrough, I ended up being educated myself about their needs for quality control/quality assurance (QA/QC). With that in mind, I would like to focus on their two key areas of concern:• How complex is the TIP installation process?• How does the QA/QC engineereffectively analyze and report TIP test results?A few months ago, during a discussion with a senior QA engineer, he asked a question that stopped me in my tracks: “Why should we do foundation testing at all?” Turning it around, I asked, “Why wouldn’t QA/QC personnel want to know everything they could about their critical infrastructure foundation?” Honestly, I didn’t answer his question nor did I fully comprehend what he was trying to say. With his experience, the engineer understood that there has not been an integrity test or a combination of integrity tests that could deliver an inside the cage and outside the cage (cover) complete data set that would provide a definitive profile of the entire shaft. Crosshole sonic logging (CSL) becomes more effective the larger the diameter of the shaft becomes, with a maximum effectiveness between 70% and 80%, but does not provide any data of the integrity of the shaft beyond a straight line between CSL tubes. Gamma-gamma logging (GGL) provides qualitative information about the concrete surrounding the GGL tube and device, and it provides information about a small percentage of the drilled shaft concrete near its outside edge."

Jan 1, 2017