Search Documents

By Karen M. Moffitt

Developments in mining methods and rates have led to an increase in the frequency and size of waste dump failures that have not been adequately predicted or explained in terms of conventional slope stability analysis. Monitoring data and visual observations suggest a unique mode of failure responsible for large runout events. A numerical model has been developed to capture commonly observed patterns of deformation, and investigate the formation of the ensuing failure mechanism. The analyses have yielded a good correlation with observed field behaviour and have provided significant insight into the coincident stresses and deformations within the dump. Results indicate that while creep effects in the waste dump could have a significant effect on the magnitudes of displacement, the overall dump stability is governed by the strength of the foundation soils underlying the toe region. Consideration of both the stress and velocity fields leads to factors of safety for various dump heights and foundation slopes that are considerably less than predicted from limit equilibrium analysis. The results suggest that conventional limit equilibrium analysis techniques may not be adequate when assessing the stability and design of waste dumps on steeply sloping terrain.

May 1, 2001

By F. N. Smith

Corrosion was observed on the aluminum pressure plates and dress-caps that hold the glazing in place on a curtain-walled building, The multi-storey building in question is situated in the downtown area of a busy Canadian city, For aesthetic reasons, the original design required the dress-caps (which have L-shaped cross-sections) to be externally clad with thin copper sheet. Since the aluminum was in direct contact with the copper trim, galvanic corrosion developed that resulted in damage to the aluminum components, Soluble corrosion products washing off the copper trim may also have contributed to the accelerated corrosion of the aluminum, The aluminum pressure plates and dress-caps are being systematically replaced with components made of fibre-reinforced plastic. The outsides of these new components will be clad with thin copper sheet in order to preserve the original appearance of the building.

Jan 1, 2005

By J. R. Smith

"The Lake Dufault orebodies were discovered by deep surface diamond drilling. When a reasonable amount of outline drilling had been completed, the decision to go into production was made. The fact that shaft sinking, lateral development, the detailing of the orebodies and stope preparation were to be carried out as rapidly as possible necessitated very close scheduling.After a study of varions possible mining methods, an open-stoping system using long-hole blasting was chosen. Diesel-powered Transloaders were selected for the mucking and transportation of ore from the drawpoints to the orepass.At the time of writing, the choice of mining method appears to have been fully justified, although more time will be required to arrive at true operating costs and efficiencies."

Jan 1, 1966

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By Colin E. Dunn

Abstract-Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

By Colin E. Dunn

Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

By I. M. Marshall

SOME years ago the writer had the opportunity to plumb a number of mine-shafts, each of which presented various conditions and difficulties. This afforded the chance to compare several methods of shaft plumbing in the light of ease and rapidity. This comparison led to the development of an adaption of the Weisbach, or approximate alignment, method, to three wires in a single shaft. Professor Weisbach, some time prior to 1850, introduced his method of shaft plumbing by triangulation on but two wires, and was the first to show that a triangle of very narrow shape is the best for this purpose. THE WEISBACH METHOD The two-wire method, using a Weisbach triangle, is described in several .English text-books on mine surveying and is used frequently in various parts of the world, but in Canada it is almost unknown. The writer has described an example of this two-wire method (1), but a brief resumé here may clarify the explanation of its application to three wires. In this two-wire method, instead of endeavouring accurately to align the instrument with the wires, it is set only in approximate alignment, and the small angle formed at the instrument is measured. This is expressed graphically in Figure l, where C represents the position of the instrument and A and B the positions of the wires. The sides of the triangle are measured as well as the angle ACB, and the angles at B and A are found by applying the Sine Rule or the formula

Jan 1, 1938

By Hans Lundberg

The magnetometer which was developed during the war for detecting submarines has proven exceedingly valuable in outlining deep-seated structures in oil exploration, and will be useful also to geologists in outlining regional structural features in the Precambrian. Our magnetometer has been developed to outline local and detail structures. 1 am quite sure that all geophysicists and geologists would agree with me that, in ore prospecting, it is important to obtain as much detailed information as possible. We know that, as we ascend from the ground and get away from the magnetic ore-bearing structures and orebodies, the magnetic intensity decreases rapidly, but, worse than that, we lose the details even faster. Figure l shows two strong, very sharp, magnetic 'highs' over two orebodies which, as our distance increases, rapidly merge into one fairly broad, moderately strong anomaly. If we drilled on this maximum, we would not encounter any of the orebodies. Therefore, we should fly the airborne magnetometer as close to the ground as possible in order to duplicate the results of the magnetic ground surveys. The first chance to accomplish this came with the helicopter, which is an exceedingly maneuverable aircraft. It can be landed in a cleared space not much more than fifty feet square. With floats, it can be landed anywhere, even in a swamp, on thin ice, or on soft snow. It can stand still in the air, hovering over a given point. It can ascend and descend vertically, fly sideways and even backwards, at the will of the pilot. It flies forward at any speed up to l00 miles an hour. The helicopter can be taken to any desired position at a given time. It can fly at any useful altitude from a few feet to several thousand feet above the ground. It can fly very close to the ground with safety. In bare areas, the survey flight may be performed a few feet above the ground. In forested areas, however, the flights, to clear the trees, must be made at l00 to 150 feet. To mark out a certain point, a small parachute-like marker may be draped over a tree or laid on the ground. This can be done from the helicopter without touching the ground.

Jan 1, 1947

By Eric D. Monrad

Supply chain simulation modeling is taking on a more prominent role in mining project planning and decision making. Transportation costs for the supply chain can form a significant component of the overall cost to provide product to the end customer. In recent years, computing power has increased, simulation software has advanced, and simulation specialists have become even better equipped to provide sophisticated analysis and recommendations. This has led to a virtuous cycle of owners expecting and supporting data-driven analytics, which drives further advancement. This paper discusses developments in supply chain planning and two case studies from recent simulation modeling analyses.

May 1, 2013

By P. Henry

Hydrometal provides an adequate technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies of our integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed.(I) Recycling of Cu-Co cement generated at the second purification step of zinc sulfate solution. (II) Recycling of lead complex materials from the lead industry.

Jan 1, 2008

By Roderick C. McDonald

Great Bear lake, the fourth largest body of water on this continent, comprises an area of approximately 12,000 square miles, and is set astride the Arctic circle, with a large portion of it witnessing both the Arctic winter night, and the Arctic summer day with its midnight sun. The very name itself, Great Bear, suggests an Arctic region. The seasonal contrasts at Great Bear lake are very marked by the cold and darkness of winter, and the warmth and brightness of summer. Signs of winter such as low clouds, snow, sleet, fog, and night frosts, generally appear the latter part of August, while ice forming on bays during the last two weeks in September ends boat travel on the lake about September 30th.Early in June the ice leaves the river mouths, during the last ten days of the month it disappears from small bays, and at some time during the last two weeks of July the main body of the lake becomes navigable. In 1916, the ice disappeared earlier than usual, and the lake was navigable on July 5th. Great Bear river generally breaks up about June 1st, but, on account of ice cliffs and floes, it is not navigable with safety until early in July. Even then, the traveller is confronted with the Charles rapids, but these might be overcome by a wagon or motor road, such as the one from Fitzgerald to Fort Smith: However, in 1931, Mr. A. W. Boland, Fort Norman, N.W.T., carried with scow and motorboat practically all freight between Fort Norman and LaBine point and Hunter bay, at the east end of the lake. During July and August, two types of clothing are required, for, although the days are mainly ones of warm sunshine, the nights are cloudy and cold. In the winter season, fur clothing is used exclusively. Considerable timber, mainly white spruce, suitable for fuel and building purposes, borders the lake and extends eastward to the Coppermine river. North of the lake, no timber is found except in the river valleys, but with oil and coal possibilities near Fort Norman, the fuel situation might be solved.

Jan 1, 1932

By Bruce Chalmers

INTRODUCTION TIE most important practical problem with which Physical Metallurgy is faced is the control of the mechanical properties of alloys. The most difficult aspect of this problem is the development of new alloys with the properties that are required for meeting exacting engineering requirements. A great measure of success has been achieved by following the empirical method and most, if not all, of the present variety of alloys have been developed by the process of experiment and observation or trial and error. It may, however, be that this method will become. less productive as time goes on, and that eventually it should be replaced by a process based on an understanding of the factors that determine the properties, so that alloys can be 'designed' to meet the requirements. This method of investigation will not be possible until a much better fundamental understanding of metals has been gained, and this will come only about as a result of a great deal of detailed research. The subject of Physical Metallurgy can be divided, as follows, into two parts: we may consider the factors which determine the structure, in the broadest sense, of an alloy. These include the composition and also the treatment to which the material has been subjected. The second aspect is the influence of the structure on the mechanical and other properties. In order to make an effective contribution in this field, it is necessary for an individual or a group to concentrate on a specific and very restricted topic. It is proposed to discuss in some detail the particular subject in which the writer and his colleagues are working.

Jan 1, 1951

By Navid Bahrani

The grain-based model (GBM) has resolved the difficulty of matching both the directtension (sc) and unconfined-compressive (st strengths of typical brittle rock by providing a synthetic material that mimics deformable, breakable polygonal grains cemented along their adjoining sides with deformable, breakable interfaces modeled as smooth-joint contacts. In this paper, a GBM utilizing a parallel-bonded base material is calibrated to match both st and sc of Lac du Bonnet granite and then used to simulate a Brazilian test. The Brazilian strength (sB) is slightly overestimated and the failure mode includes ductile post-peak response that is not representative of what occurs in laboratory Brazilian tests. By reducing the grain tensile strength, grain failure occurs during the Brazilian test and a more realistic failure mode that includes brittle post-peak response is obtained. However, the unconfinedcompressive strength of the modified material is too low. Sensitivity analysis on the grain and grainboundary strength properties demonstrates that the grain tensile strength controls the sB/sc ratio. Because the grain strength is controlled by the parallel-bond properties and the lowest achievable st/sc ratio in a parallel-bonded material is ~0.25, it is concluded thatsc, st and sB for a typical brittle rock cannot be matched with a GBM that utilizes a parallel-bonded base material.

Jun 1, 2012

By Paul A. Glapa

Quality is much more than providing a product that functions properly. True quality is a way of thinking, a way of doing business, and, ultimately, a way of satisfying a customer?s long-term needs. A true commitment to quality requires a top-down management commitment, with a willingness to change what needs to be changed and to expand upon ?best practices? that are already done well. Is there a cost to creating and maintaining a quality program? Of course there is, but the cost of not having a focused program is much greater. We have come to regard quality as an investment that pays dividends to both the supplier and customer. The lack of quality costs everyone and the customer pays the ultimate penalty. With modern, highly engineered surface mining equipment the end user calculates cost in terms of lost production (revenue), not simply the cost of the part. Bucyrus International, Inc. is a company that has listened to its customers and has dedicated itself to implementing an advanced quality program. The ultimate goal being the creation of a high quality product with extended reliability for the customer. The result is reflected in Bucyrus? current product offerings and highlighted by the new 495HF electric rope shovels at Albian Sands mine.

May 1, 2003

By Jeremy P. Richards

Key inputs are volatiles and heat: Slab dehydration: Breakdown of amphibole and serpentine in hydrated oceanic crust releases fluids into mantle wedge, causing metasomatism.

May 1, 2008

By P. J. Adams

Environmental regulations require means for controlling emissions of SO2 NOx and particulate when burning coal. The combustion of coal in limestone fluidized beds is one of the most promising techniques for the necessary reduction in emissions. Fluidized-bed firing, furthermore, offers potential economies in capital equipment. The world's largest steam generator applying fluidized-bed techniques was built under the sponsorship of ERDA and installed in Rivesville, West Virginia. This paper describes the design and discusses the start-up and development difficulties which were experienced during the period from initial operation to current readiness for commercial operation. Other developments leading to utility and industrial fluidized-bed steam generating equipment are reviewed. The future potential of this promising technique is discussed.

Jan 1, 1979

By Ian L. Price

Description of the Springhill Coal Field The Springhill coal basin, which lies in the approximate centre of Cumberland county, Nova Scotia, is of Carboniferous age, and forms a syncline plunging to the westward at an angle of 32° at the outcrop but gradually flattening to the dip. It contains several workable seams of varying thicknesses, a generalized section of the measures in descending order from the surface being: [] The 1,114 feet of strata is composed of shales and sandstones, and all of the coal seams mentioned, with the exception of No. 4 and No. 5, have been mined commercially. The coal is said to be the best steam and domestic coal in the Province of Nova Scotia.

Jan 1, 1946

By G. W. H. Norman

The surficial Archæan rocks of the southern gold belt of western Quebec are constricted near Kewagama lake by granite masses to the north and south. This divides the belt into natural eastern and western parts. This paper deals with the eastern part, extending from Malanie to Haig township. In this section the Keewatin-Timiskaming rocks have a length of about 70 miles and end abruptly against garnetiferous gneisses of the Grenville terrain. In the western half of the section where exploration has been under way since the early twenties, there are sixteen mines that are or have been in operation, and eleven prospective mines. In the eastern half where exploration has been carried on since the early thirties, six prospective gold mines are under development, one· of which, Louvicourt Goldfields, is at the initial production stage. Of the sixteen properties in the western half that are operating or have operated, all, except the Golden Manitou, which is a base metal mine, and the old Green Stabell from which there was a small production of copper, produce gold. Of the eleven prospective mines in the western half nine have gold. New Bidlamaque has gold and copper and one, East Sullivan, has copper-zinc ore. Since production began in 1927 gold, silver, zinc, copper, and lead having a total value of about $10,000,000 have been produced from the mines of the eastern section of the southern gold belt of western Quebec.

Jan 1, 1954

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By L. Tapia

The main disturbance for stability in primary grinding using SAG mills is related to continuous changes in the ore being fed to the plant, such as size and hardness. Searching for stability is the first step to accomplish, before trying to maximize the mill throughput. The time variability in the characteristics of the ore being fed from the mine to the plant must be known or inferred to perform adaptive changes in the grinding process control. In day to day operation, such information is not available in real time. Transport times and inventories between the mine and the plant complicate the situation. Under this scenario, Minera Los Pelambres implemented a grinding optimization strategy, based on the real time analysis of certain process variables, such as ore size, mill current consumption, pebble generation and throughput. As a result, both grindability and stability indexes are inferred. This is equivalent to inferring the ore characteristics by knowing its effect on the grinding behavior. These two indexes permit control of the SAG mill total charge level and hence, allow optimization of throughput by means of an expert control system.

Jan 1, 2007