Search Documents

By M. Nowak

Extreme high grades often exert too much influence on surrounding block estimates, leading to a smearing of high grades that can cause overestimation of mineral resources. This concern underlies the decision to cap high grades, i.e., to lower the highest grades in a drill hole data set to some level deemed to be reasonable for producing reliable resource estimates. The choice of a capping level can, by itself, have a large influence on the analysis of the economic viability of a project. Despite this, it is often a choice that is made arbitrarily, guided more by art and tradition than by sound technical analysis. This paper makes suggestions for good capping practices, using methods and procedures that have been presented elsewhere, in the technical literature and in conference papers. The authors propose to use capping only if absolutely necessary, and review examples of cases where capping may not be necessary, or where capping does not make the estimates more reliable. It addresses two particular instances where capping is recommended: (1) where there is good reason to believe that estimation with uncapped grades will overstate the true underlying average grade, and (2) where there is potential for overly optimistic assessments of local block grades in the vicinity of some very high grade assays. The proposed capping practice is based on adjustments to only a very few high grade assays. The level of this capping can be assessed by bootstrapping and through analysis of the effect of extreme values on summary statistics like the average and the coefficient of variation. The paper recommends that good practice include an examination of the potential for local overestimation in higher grade areas.

Aug 1, 2013

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By Lawrence Devon Smith

"The Management and Economics Society has undertaken a survey of industry practice in the evaluation of mineral projects. The survey addresses a number of issues relating to evaluation techniques, discounted cash flow methodology, and risk. Completed during the spring and summer of2005, the results provide a record of opinion at an active and vital time in our industry.The 2005 survey questionnaire was distributed by e-mail to groups and organizations around the world. There were 22 respondents out of several hundred questionnaires distributed (we gather this small proportion of respondents is typical for such surveys). The responses, although a small number, show a consistency that suggests that the survey has captured the views of the industry. The results of the survey are summarized below in series of tables and graphs.The reader is cautioned that the results are a snapshot of industry practice at a point in time as represented by a small sampling of the industry's practitioners. These results should be viewed as indicative values."

Jan 1, 2003

By A. Zarei-Hanzaki, O. Golmahalleh, S. M. H. Hosseini, H. Azizi-Alizamini

The main importance of acicular ferrite microstructures arises from their desired combination of mechanical properties in comparison with the bainite and ferrite-pearlite microstructures. Several factors affect the microstructural transition from bainite microstructure into the acicular ferrite one. As is well established any factor corrupting the prior austenitc grain boundaries nucleation potential, such as the thin layer of allotriomorph ferrite and the austenitc deformation inhomogenities may promote the acicular ferrite formation instead of bainite. Accordingly, this study deals with the effects of the aforementioned features on the acicular ferrite formation in low carbon microalloyed steel. The results indicate that the formation of strain-induced ferrite at the prior austenite grain boundaries accompanied by deformation inhomogenities in the austenite grains change the effectiveness of allotriomorph ferrite on acicular ferrite formation from active to inert one.

Jan 1, 2004

By Howard Keele

"The Whitewood Mine near Edmonton, Alberta, is owned by TransAlta Utilities Corporation and operated by Manalta Coal Ltd. Approximately 2 million tonnes of sub-bituminous coal is supplied annually to the Wabamun Generating Plant. A high water table, high groundwater pressure, and structural folds contribute to stability problems in the fine-grained overburden. Significant increases in coal recovery have been achieved in recent years through improvements in water management and mining methods. Agricultural capability of the post-mining landscape has also been improved following the completion of mining/ reclamation activities. Introduction The Whitewood Mine, located to the north of Lake Wabamun and seventy kilometres west of Edmonton, Alberta, is owned by TransAlta Utilities Corporation and operated by Manalta Coal Ltd. Figure 1 shows the location of the Whitewood Mine with respect to the city of Edmonton. The mine presently supplies two million tonnes annually of sub-bituminous ""C"" coal to the 582-megawatt Wabamun Generating Plant located adjacent to the mine. The area is characterized by a high water table-, rolling coal seams and an overburden that consists of muskeg, clay and various sedimentary layers of sand, gravel and fine-grained sandstone. These distinctive characteristics require careful attention in order to not only meet the coal delivery requirements of the Wabamun Generating Plant but also to do so economically. Historical Background A small-scale underground coal mine was opened in the Wabamun area in 1910 by the Conner Coal Mining Co. Ltd. Underground operations were continued by several operators until 1948 when the Alberta Coal Co. Ltd. opened a strip mine which was subsequently taken over by the Alberta Southern Coal Co. Ltd. in 1951. The small-scale strip opera"

Jan 1, 1985

By D. F. Sherwin

"THE AREA which is described in this paper (Fig. 1) includes the continental margin of eastern Canada extending from the Gulf of Maine to the north edge of the Grand Banks, which, including the continental shelf, slope and rise, comprises an area of about 600,000 square miles. The paper is intended to give a background of the geological setting of this region in the context of its ultimate potential for oil and gas reserves in close proximity to the Nova Scotia energy market.HISTORY OF EXPLORATIONThe history of geological exploration of this area really began in 1878, when U.S. fishing boats brought back samples of rock recovered in trawls from their expeditions to the long-famous fishing banks off Canada's East Coast. Tertiary and Cretaceous fossils recovered from these samples indicated that the eastern Canadian continental shelf was actually the submerged northern extension of the Atlantic Coastal Plain."

Jan 1, 1972

By Samuel Nunoo

Gibraltar Mine is an open pit copper-molybdenum mine in central British Columbia. The stability and potential failure modes of pit walls in the Granite Pit are controlled by the orientations of joints and faults. The structural geology also has an impact on as-mined bench geometries. Geotechnical mapping and surveying were conducted using stereo photographs and photogrammetry software. Detailed digital terrain models were constructed to determine the pit wall geometry and the locations and orientations of larger structural features. The pit wall geometry is compared to conventional survey results and the mapped structures are compared to results from a nearby geotechnical borehole.

Aug 1, 2013

By Fulchand Shende

Around the world many potash mines experience brine inflow problems. The presence of brine in underground excavations may induce structural and stability problems. A study has been carried out to simulate the effect of brine on the performance of pillar support. The testing program consisted of loading potash specimens in a creep frame, and simulating inflows by continuously pumping brine into an experimental cell. Brine temperatures and load conditions were varied to simulate several mining and inflow conditions. Specimens were fitted with acoustic emission transducers to monitor energy emissions during an eight-hour test duration. Samples of brine were also collected to provide K+ and Na+ concentration data necessary for an accurate assessment of the dissolution process. Test results indicated that dissolution rates are highly dependent on brine temperature and load conditions. Loads approaching 50% UCS tend to generate very high rates of energy emissions, often leading to the failure of the simulated pillars. This study demonstrated that acoustic emission could be effectively used for predicting the performance of pillars when exposed to inflow brine.

May 1, 2001

By Damian Connelly

The option to leach iron from low grade copper concentrates could reduce transport costs and significantly improve the saleability of the concentrate. In addition, it reduces smelting costs and can remove undesirable impurities. The trend to produce cleaner and higher grade copper concentrates is very appealing to the smelters. A recent copper project came on line and there were three serious deficiencies which were not identified in the feasibility study. This came as a surprise and resulted in a number of projects to investigate ways of rectifying the problems in the shortest timeframe possible and using minimal new capital. The first serious issued not identified when commissioning was the lower than expected copper recovery, which was 70% compared to a predicted recovery of 80% to 87% in the feasibility study. This required investigating new flotation reagents and incorporating controlled potential sulphidisation. The second serious issue overlooked is the presence of significant amounts of talc minerals (insol) in the ore which are naturally floatable. This leads to lower concentrate grade and attempts to remove the talc resulted in lower copper recovery. Smelters have limits on the amount of talc in concentrate because it produces viscous slags and difficulties for the smelter. It also incurs higher transport costs. The third serious issue not identified in the feasibility study was the high arsenic reporting to the concentrate. Arsenic is a penalty element for smelters and at levels exceeding 0.3% the smelters may reject the concentrate. Arsenic is a problem environmentally for copper smelters and penalties apply when it is high. This paper describes the options for penalty element removal and suitability to incorporate into the modified flowsheet. It also highlights where the geometallurgy was not properly addressed and how these surprises could have been avoided. INTRODUCTION From 1970 to 1985, a copper company undertook metallurgical testwork on the Peruvian project copper ore. The ores were mined underground and treated over many years previously. Various other groups undertook studies and work until Aker Kvaerner undertook a feasibility study in 2006. Three ore composites were tested and grind-recovery relationships were developed. The feasibility study testwork identified that talc was a possible concern and will have an impact on copper concentrate grade. This was to be managed by blending. The current operating reality is that there is so much talc in the ore body it is not possible to blend it out. There was far more emphasis on molybdenum recovery. No mention was made of arsenic issues other than blending. There was a Concentrate Leach Study and a Molybdenum Hydrometallurgical Plant Study but these options did not proceed to a final flowsheet. A Scoping Study in 2006 looked at a Heap Leach project. The heap leaching gave very poor copper recovery on the sulphide ore. Heap Leaching was evaluated and tested for the high talc and high arsenic ore but recoveries were poor. The Aker Kvaerner feasibility study opted for a simple primary crush SAG/ball grind followed by flotation and sale of a concentrate. This is the current flowsheet utilised and the scale of the project is very large based on processing 117,200 tonnes of ore per day. A feasibility study does not guarantee success and the deviations from the feasibility study suggest there is a lot of technical work required to improve the current metallurgical performance.

Jan 1, 2019

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. The Ore and ProductsThe mines in the Saskatoon area — Agrium, PCS-Cory, PCS-Allan, PCS-Patience Lake, PCS-Lanigan and IMC-Colonsay — extract the ore from the Patience Lake member. The mines in the southeast corner of Saskatchewan — IMC-K1 and K2, PCSRocanville — extract from the Esterhazy member, while IMC-Belle Plaine, near Regina, solution mines potassium chloride from both potash-bearing members.Ore from the Patience Lake member is a medium-grained mixture of sylvite and halite, with a KCl content of 36%, insolubles averaging up to 5.5%, and little or no carnallite.The ore from the Esterhazy member is a coarse-grained mixture of sylvite (KCl) and halite (NaCl) with a small amount of water insolubles, and some carnallite (a K-Mg chloride). Average run-of-mine grades are about 30% KCl."

Jan 1, 2003

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By Laxman M. Amaratunga, Nuri Hrnidi

"Reactive pyrrhotite tailings were agglomerated using the Cold Bond Tailings Agglomeration (CBTA) process with low cost binders; Portland Cement and fly ash. Various chemical additives, were used to retard acid mine drainage (AMD), including acid neutralizers, surfactants, sealants, and bactericides, which were encapsulated into the agglomerates. The choice of these additives was based on their low cost, low toxicity, and environmental friendliness. The main objective of the study was to examine the long term stability of these reactive tailings agglomerates towards AMD when used as aggregates for disposal in underground paste backfill.A carefully controlled kinetic stability test was carried out using specially designed humidity cells suitable for testing pellets. Using the humidity cell test method a 20-30 year AMD test may be accelerated to 50 weeks. During this period the following parameters were monitored: pH, redox potential, conductivity, sulphate, acidity, and dissolved metals.Results indicated that most of the encapsulated additives were successful in retarding AMD, while the control samples produced significant amounts of acid generation. The water soluble surfactant Enviroseal, and the sodium silicate sealant were very effective as a long term retardant for acid generation reactions in the sulphidic tailings when exposed to oxygen, water and iron-oxidizing bacteria.IntroductionThe sulphidic material discharged from concentrators becomes reactive upon exposure to air and/or water. Pyrrhotite (Fe0 S0_1) and pyrite tailings in particular which are discharged from the beneficiation process in the mining and mineral processing activities consist of finely ground particles. Upon exposure to oxygen and moisture, the tailings become reactive due to the instability of the metal sulphide minerals present which undergo spontaneous oxidation, thereby producing a weak sulphuric acid. Therefore, the long-term behaviour of the tailings can have a significant impact on the environment, due to acid mine drainage (AMD). AMD is created during natural atmospheric weathering when leaching action (natural and bacterial) conditions are present in the process wastes discarded during the mining and milling of sulphur bearing ores, and consequently it plays a major role in surface water chemistry."

Jan 1, 1998

By Fidelis T. Suorineni

The conditions for rockburst occurrence are traditionally identified as: high stress, high extraction ratio, strong brittle rocks, folding, faulting, and unfavourable excavation geometry. Based on a critical review of case histories, this paper identifies oblique loading of orebodies by the major far field principal stress as a cause of rockbursts. Orebodies subjected to this loading condition are termed orebodies in shear. Orebodies in shear are subjected to compressive and shear loads. The case histories presented unambiguously show that the magnitudes of the far field principal stress alone, and a knowledge of the conventional rockburst causing factors are not sufficient for mine planning and design. The orientation of the major far field principal stress, or for that matter the driving stress relative to the orebody axis, should be recognised as one of the causes of rockbursts. It is suggested that since stress orientation is an important factor, and orientations from stress measurements are so variable, orientations from stress measurement data be complemented with underground observations from borehole and excavation breakouts to determine the actual in situ stress orientation, whenever possible. Also stress modelling for the design of critical elements (pillars) should include a sensitivity analysis on the relative critical field stress direction. The paper emphasises that special attention should be paid to or

Jun 1, 2012

By J. A. Brusset

THE Greenhill mine of West Canadian Collieries, Limited, is situated at Blairmore, Alberta, and produces 2,500 tons per day of bituminous coal. On Monday, October 25th, 1943, smoke was discovered by a party of firebosses on their regular weekly inspection of air-ways. Probably the fire had been smouldering for several days but, as it had started on the outcrop at the top of an old raise filled with dirt, only a small quantity of smoke could filter through, and the plume of mist that crowns the fan at that season had prevented the fan-man from noticing it. This raise is only about 200 feet from the fan, and is 70 feet long between the fan-drift and the outcrop. It was impossible to prove the origin of the fire, as it had probably started several days before it was discovered, but it is possible that a careless smoker may have thrown a match into the opening at the outcrop, and that the old, dry timber had caught fire. The airways are in No. 2 seam, a bituminous seam 18 to 25 feet thick surmounted by shales and sandstones. Only 45 feet vertically above it is No. 1 seam, 12 feet thick, overlain by a strong conglomerate. In that vicinity, No. 1 seam had been worked out about ten years ago and the strata between the two seams are undoubtedly fissured. The pitch of both seams is 43 degrees.

Jan 1, 1945

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By P. Nelson

Extending the campaign life of the Mitsubishi furnaces at Xstrata Copper's Kidd Metallurgical Division Copper Smelter has been a major focus of attention for many years. One aspect of this effort is real time monitoring to detect abnormal conditions and safely shut the furnaces down before significant damage occurs. Traditional real time methods of monitoring the integrity of refractory furnaces containing molten metal include alarms on individual temperatures of the refractory or cooling water. The need to set alarm limits which are not exceeded across the range of normal operating conditions leads to a system that only provides a limited warning, if any, before a failure occurs. Integrity monitoring systems that look at many different signals and alarm only changes in the relationships between the signals have been implemented on the smelting and converting furnaces. The systems are based on principle components analysis (PCA) models and implemented with the monitorMV software package. These provide much more sensitive and selective alarms so that changes in integrity are alarmed well in advance of any event. At a critical alarm level, the converting furnace is set to automatically shut down so that operating and technical personnel can review the situation. The configuration of the systems and operating experience with them will be discussed.

Jan 1, 2007

By DALE MacGREGOR, VERA TUREK

lndusmin Limited acquired the St. Donat quartzite deposit in 1967 to produce high-quality silica for use in the sandblasting and silicon carbide industries. The quartzite, of Grenville age, is highly friable and porous. This is due to numerous small, kaolinite-coated cavities in the quartzite; the cavities were formed through leaching, probably by rising hot solutions.

Jan 1, 1984

By M. A. Nadar

Harsh and dynamic construction sites are generally equipped with cranes in order to rapidly and conveniently move heavy loads from one location to the other. If not properly inspected and managed, this operation can be very hazardous and lead to accidents. As such, a reliable and self-contained monitoring system that can update construction and safety personnel about the status of the crane, the weight of the load lifted, the location of the boom with respect to nearby buildings and other tower cranes, and the weather conditions under which the crane is operating, is deemed necessary. This can lead to significant time and cost savings as well as safety and productivity improvement due to the accuracy and immediacy of relevant on-site crane information delivery. This paper takes the initial steps and presents research targeted at evaluating the capability of wireless sensor networks (WSN) for monitoring tower crane operations in construction environments. A reliable long range WSN system is implemented and information is obtained from various special-purpose sensors (temperature, wind, proximity, etc.) mounted on special motes that relay data to and from each other and a central hub. The latter continuously monitors and manages network performance and relays incoming data to the host application. This application, in turn, displays the received data, and maps it onto a user-friendly visualization scheme, triggering alarms when a set of pre-programmed rules and safety conditions are crossed. The components of the proposed system have been tested through proof of concept experiments and preliminary results highlighted the potential of WSN systems for improving monitoring of tower cranes and reducing related accidents on construction sites, especially in Lebanon and the Middle East region where safety precautions are usually not properly implemented.

Aug 1, 2013

By Michael L. Wayman

Native copper is copper which exists in nature in elemental, metallic form, rather than being chemically combined as is the case with the more usual oxides, sulphides, carbonates, etc. Several other metals, including gold, silver and platinum also occur in native form as do, rarely, iron, lead and mercury; a few naturally occurring native metal alloys, notably electrum (gold-silver) and tumbaga {gold-copper or gold-silver-copper) are also known. An analysis of the relative availabilities of native metals as nuggets in a useful size range111 shows native copper to be by far the most abundant of the native metals, exceeding both gold and silver by at least two orders of magnitude. While such an estimate is crude, it serves to illustrate why copper was one of the first metals to have been used by ancient peoples. Native copper is known to occur on all inhabited continents, although its exact occurrence and abundance in ancient times cannot be unambiguously determined because many surface deposits may have been totally exploited and are therefore no longer identifiable. It is clear, however, that native copper does or did occur in all areas inhabited by the early metal-using cultures, for example in the Andes, in Central America and in the Near East. It is remarkable that most of the world's native copper occurs in the deposits of the Lake Superior region, primarily on the Keweenaw Peninsula of northern Michigan and on Isle Royale, an island in Lake Superior some 50 miles north of the Keweenaw deposits. Canadian deposits of native copper are found in Newfoundland and Labrador, Nova Scotia, Quebec, Ontario, British Columbia, the Yukon and the Northwest Territories (on Victoria Island, Bathurst Inlet and the Coppermine River area). It was to locate the latter deposits that the explorer Samuel Hearne was sent overland from Hudson's Bay in 1770; they were also surveyed by Sir John Franklin's expeditions in the 1820s.

Jan 1, 1999

By R. Tipman

"In 25 years, processing of tar sand progressed from two small pilot plants to two major commercial operations owned by Syncrude and Suncor. These plants mine tar sand and extract the bitumen which is then converted into a synthetic crude oil. Considerable research on extraction of bitumen from tar sand has been undertaken by these two companies as well as other major oil producing companies, private individuals, universities and the federal and provincial governments. These studies have produced a number of alternate processing schemes which have yet to be commercialized. The producing companies are focusing their efforts on achieving increased processing efficiency, which includes improved bitumen recovery, reduced unit cost, energy conservation, and equipment reliability. In this review, the Syncrude process and examples of new process developments will be briefly described. IntroductionTwenty-five years ago, tar sand processing was limited to two pilot plants owned by Cities Service Athabasca Ltd., and Great Canadian Oil Sands. Earnest Manning was Premier of Alberta and was inviting proposals for the construction of a commercial tar sands plant. The invitations called for a much larger operation than those which had been undertaken in the past. All of the previous attempts at commercial operations up to 1960's had failed, largely because of a poor technical understanding of the process requirements, lack of suitable equipment, and lack of adequate capital. The previous record was not good. The pending new large scale plant was based on improved but not proven technology and equipment, which were developed from the pilot plant studies. In addition, the surplus of conventional oil in Alberta and low world oil prices were factors reducing the need for such a plant."

Jan 1, 1987