Search Documents

By Marcel M. Djivre

The paper will outline the methods and test procedures including the evaluation criteria currently used at the Materials Testing Laboratory (MTL), Sudbury, Ontario, Canada, a laboratory approved by the Ontario Minister of Labour for the purpose of testing or examining mine shaft ropes or other hoisting appliances. Also for Canadian mines the paper will suggest proposed criteria to be used at MTL for the evaluation of ropes used in "ultra-deep" single-lift shafts. Most of the methods and test procedures currently used at MTL were adopted during the revision of the CSA Standard G4, Steel Wire Rope for General Purpose and for Mine Hoisting and Mine Haulage to be published most likely in year 2001. In this latest or sixth edition of CSA Standard G4, a new Clause 14 has been added outlining the requirements for in-service destructive testing of steel wire ropes for mine hoisting applications. The existing fifth edition of CSA Standard CAN/CSA -G4-92, which is intended for the manufacturing of new ropes, includes requirements for raw materials and construction features for round strand and flattened strand rope, and locked coil rope in bright and galvanized finish.

May 1, 2001

By J. H. McKibbon

This paper outlines the basic steps in the sizing of electrostatic precipitators according to the Deutsch equation. Design parameters that do not appear in the equation are also described.

Jan 1, 1971

By Ken McClure, Alex Day

Located North of Williams Lake British Columbia, Gibraltar Mine is the fourth largest open pit Copper mine in North America. Gibraltar commenced Copper concentrate production in 1972 with a mill throughput rate of 30,000 tons per day. A series of expansion projects, including installation of a second SAG mill with variable speed drives in 2013, has increased mill throughput to 85,000 tons per day. Over the past 24 months, Gibraltar Mine in partnership with Spartan Controls has executed several advanced process control programming projects culminating in the implementation of a Continuous Speed Controller (CSC) for the most recently installed SAG mill. This paper covers development and results for the SAG mill speed controller. INTRODUCTION In January 2016, the price of Copper fell below $2.00 USD per pound, the lowest price in 7 years. Gibraltar Mine faced a significant challenge; how to maximize profit in an environment where capital spending was not an option. An opportunity was quickly identified to improve performance through increased automation and advanced control of the grinding processes. Beginning in March 2016, Gibraltar Mine partnered with Spartan Controls to introduce Advanced Process Control (APC) to the grinding circuits. The collaboration between metallurgical and process control engineering disciplines proved to be effective for achieving gains in throughput, reliability and productivity for the mill process. The Gibraltar milling facilities include 2 grinding-flotation plants for concentration of chalcopyrite ore with throughput rates of 58,000 tons per day (Concentrator 1) and 38,000 tons per day (Concentrator 2). Each of the two concentrators has a 34’ diameter SAG mill powered by 2 GE 4800 kW synchronous electric motors. For SAG 1 (in concentrator 1), power is transmitted through 2 Eaton Airflex clutches. For SAG 2 (in concentrator 2), the motors are driven by 2 TMEIC Variable Frequency Drives (VFDs). All programming is done using DeltaV, which Gibraltar uses as its Distributed Control System (DCS) and Human Machine Interface (HMI).

Jan 1, 2019

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

By Emmanuel John M. Carranza, Martin Hale

Abstract- An application of logistic regression to mapping of gold potential in the Baguio district of the Philippines is described. Categorical map data such as lithologic units and proximity classes of curvi-linear features, based on spatial association analyses, are quantified systematically and used as independent variables in logistic regression to predict the probability for presence or absence of gold mineralization. Regression experiments to compare between using all independent variables that are associated spatially with the response variable and using only statistically significant independent variables are performed. The results of the regression experiments are similar; however, the use of all independent variables produces slightly optimistic results but better prediction rates for the known gold deposits in the test district. At least 68% of the ‘model’ large-scale gold deposits and at least 76% of the ‘validation’ small-scale gold deposits were predicted correctly. The predicted geologically favorable zones are also similar to delineated geochemically anomalous zones. The technique presented using logistic regression as a data integration tool is effective for geologically constrained technique of mapping mineral potential.

Jan 1, 2001

By Brian Putland, Fred Kock, Leigh Siddall

Single stage semi-autogenous / autogenous (S/AG) milling has become a common design for a variety of ore types with the advantages of being comparatively low capital cost and flexible for future expansion. The single stage SAG/AG milling option is ideal for starter projects with significant exploration and expansion potential. Currently a number of the largest SAG mills designed are installed in single stage configuration. This paper discusses the challenges associated with the process design of single stage SAG/AG milling circuits, the design flexibility required to ensure a robust circuit and the operating techniques adopted at successful installations.

Jan 1, 2012

By Steve Dismuke, Tom Diment

In December 1994, Polaris decided to investigate the use of cemented rockfill (CRF) to supplement the existing frozen rockfill system. Extraction plans for the remaining ore reserves required a backfill with superior stiffness proper-ties and capable of developing high early strengths. Although CRF has been used success-fully at several mining operations, there was the additional challenge of making a reliable cemented product in permafrost conditions. There was also the challenge of procuring and storing one year’s supply (13 000 tonnes) of bulk cement. By the spring of 1995, following three months of research, test work and process design, the decision was made to proceed with the procurement and construction of a 3000 tpd batch plant. An ambitious completion date of December 1995 was set. Team Manufacturing of Langley, British Columbia was awarded the contract, complete with the considerable task of having the batch plant fabricated and ready for sea lift shipment by August, 1995.

Jan 1, 1996

By K. A. Hughes

Under the oxidizing conditions of the McClean Lake Tailings Management Facility (TMF) hydrocarbons entrained on the surface of tailings material from mill processes are gradually converted to soluble bicarbonate ion. This has been observed to be a process occurring over approximately three years likely encouraged by the presence of a microbiological community within the tailings mass and in the water column. A recent tailings sampling campaign has provided evidence that bicarbonate ion is participating in the conversion of gypsum to calcite. In older tailings, equilibrium with calcite appears to be controlling the terminal bicarbonate ion concentration.

Aug 1, 2010

By Trung Nguyen

Midwest is a unique uranium deposit with exceptionally high arsenic content. The ore body is located 17km west of the McClean Lake operation. The McClean Lake mill will be modified to process Midwest ore and handle solid wastes coming from the Midwest water treatment plant. This paper describes the modifications required of the McClean Lake mill, process challenges associated with treatment of the arsenic, and the possibility of recovering nickel and cobalt as a by-product. It also reviews the complexity in the design of the Midwest water treatment facility which incorporates reverse osmosis technology with conventional physical-chemical water treatment.

Aug 1, 2010

By C. W. Eggert

"The idea for this talk came to me last year when I was attending the Canadian Gold Metallurgists Meeting. I talked about it to a friend of mine who is an authority on mineral dressing, particularly the theoretical end of the business. He remarked that this was an excellent technical note, why don't you write it up. This is what I have for presentation this morning. I hope in presenting this type of idea in this way it is in keeping with the tradition of the Canadian Gold Metallurgists which was to function on a not too sophisticated level and where operators could get together and trade ideas in an informal way.My basic thesis is that it should be possible to evaluate screen analyses by the application of the standard statistical probability theory. In any statistical analysis the sample is the first consideration. If we look at existing methods of size evaluation we find it is usually based on the fact that a given particle will pass one square aperature and not another. One system of standardizing how these aperatures will be set up is based on Rittenger' s work with the ratio of hole sizes proportional to the square root of 2. Keeping in mind the limitation we have accepted this as our method of 11 sizing"" in attempting to apply standard statistical methods to screen analysis."

Jan 1, 1968

By M. J. Bennett

"The Quemont mill is primarily a differential flotation plant in which copper, zinc ·and pyrite concentrates are recovered. Native gold and silver are associated in the form of very small particles with all the minerals contained in the ore: chalcopyrite, sphalerite, pyrite, pyrrhotite and even with the gangue rock.The proportion of the precious metals associated with chalcopyrite is such that the best recoveries we can obtain in our copper flotation concentrate are about 68 percent of the gold and 51 percent of the silver in the ore. In order to improve the total recoveries of precious metals it is necessary for us to float a pyrite concentrate and treat it by cyanidation for the extraction of whatever gold and silver we can obtain in this manner. In spite of the fact that we regrind this concentrate to 75 percent minus 325 mesh, it is difficult to extract much more than half of the gold and silver present in the pyrite concentrate by cyanidation, due to the extremely fine association of the precious metals with the pyrite.In 1963 we produced 86, 853 ounces of gold by flotation alone, and 14, 581 ounces by cyanidation. These amounts are equivalent to 67. 74 percent and 11. 37 percent respectively of the total gold in the mill heads. Comparable figures for silver are 325, 598 ounces by flotation and 99, 448 ounces by cyanidation; and 51.37 percent and 15.69 percent respectively.The total annual value of these metals (ie. $4, 000, 000) qualifies Quemont as a precious metal producer of some note. On the other hand, it is evident that by far the greater proportion of our gold and silver production is contained in copper flotation concentrates. When the income from our copper and zinc values is also considered, the much greater importance of flotation compared with cyanidation in our operation may be appreciated. This explains why most of our work on controls has been carried out in our flotation mill, rather than in our cyanide plant. Some of the controls installed there could, of course, be employed in either type of operation."

Jan 1, 1964

By R. Gordon, J. Palich, W. Qian

The EarthProbe DCIP system deploys tightly spaced electrodes connected to a centralized data acquisition system that enables arbitrary selection of current and potential electrodes through relays. Rapid data collection (approximately 1000 readings per hour) and advanced signal processing allow for efficient use of conventional and novel arrays and the removal of natural and cultural noise. What is unique about the system is its electrode and borehole cable design, which allows seamless integration of borehole and surface measurements. EarthProbe operates in four configurations - surface, borehole, borehole-to-borehole, and surface-to-borehole (a variant of the borehole-to-borehole configuration).

Jan 1, 2011

By K. Barbetti, J. Avraamides

"The processing of gold ores with high silver contents can provide operational challenges, such as high cyanide consumption, retardation of gold leaching and competition during adsorption stages of carbon-in-pulp/leach/column (CIP/CIL/CIC) circuits. In particular, the silver, which is about 1.5% of the value of gold, competes with gold during carbon adsorption due to its higher concentration in many Ag-Au ores, potentially leading to gold solution losses. Fresh and partially fouled (barren and regenerated) activated carbons were evaluated at various Ag:Au ratios and total metal concentrations with regard to the adsorption kinetics and equilibrium loadings. Conventional Freundlich isotherms were found to be highly inaccurate for predicting equilibrium loadings in the competitive adsorption environment. An integrated model, which incorporates competitive adsorption kinetics with a modified competitive adsorption isotherm model has been developed and validated using plant and laboratory data. The model performance and some of its salient features will be discussed.INTRODUCTIONThe processing of gold ores with high silver contents can present a range of operational challenges, such as high cyanide consumption, retardation of gold leaching and competition in carbon adsorption circuits. Silver is often present at significantly higher concentrations than gold in many gold-silver ores and competes with gold in carbon adsorption circuits, limiting the gold loading rate and capacity, resulting in gold solution losses and reduced gold recovery.Curtin University’s Gold Technology Group has evaluated fresh and partially fouled (barren and regenerated) activated carbons at various Ag:Au ratios and total metal concentrations to determine the adsorption kinetics and equilibrium loadings for gold and silver. Conventional Freundlich isotherms were found to be highly inaccurate for predicting equilibrium loadings in the presence of both gold and silver.An integrated model, which incorporates competitive adsorption kinetics with a modified competitive adsorption isotherm model has been developed and validated using plant and laboratory data. This paper describes the model performance and some of its salient features."

Jan 1, 2016

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By Blair Hrabi

Introduction; ?Risks Associated with the Resource Estimation Process; ?Limitations of Available Data; ?Geological and Structural Control of Mineralization Trends; ?Recognizing Multiple Mineralization Controls and Complex Trends; ?Accurate Geodomaining; ?Conclusions.

May 1, 2013

By S. Torizuka, I. Mizushima. Kawasakitohri, A. Ohmori, K. Nagai

Strain (work)-hardening in tensile tests were examined for low carbon steels with various ferrite grain sizes ranged from 0.4µm to 16µm. The steels had microstructures composed of ferrite grains and dispersed cementite particles. They were fabricated through warm caliber rolling with an accumulative area reduction of 93%. Strain-hardening rate at a given strain increased with an increase in volume fraction of cementite particles. The balance of yield strength and uniform elongation for ultrafine-grained structures could be improved by the dispersion of cementite particles. Effects of the cementite dispersion and the ferrite grain size on the strain-hardening rate can be roughly explained by the work-hardening model with GN-dislocation density. Strain-hardening design using dispersed cementites was proved to be effective in controlling ductility of the ultrafine-grained steels.

Jan 1, 2004

By A. West, F. Mohammadi

Growing awareness of selenium bioaccumulation has resulted in selenium management becoming an important environmental issue for mining operations. Selen-IX™ is a novel ion exchange based technology developed by BioteQ to provide an effective solution for removing selenium oxyanions from mine impacted water to single-digit µg/L levels. The technology offers significant potential benefits when compared to incumbent biological treatment processes, including substantially reduced capital and operating costs and significantly reduced production of a selenium-containing sludge for final disposal. This paper reviews the key features of the Selen-IX™ process and presents the results of recent pilot testing on selenium impacted water.

Jan 1, 2014

By Jean Robitaille

La découverte du gisement du puits Penna a nécessité une révision complète de tous les circuits du concentrateur Laronde pour permettre, premièrement, l?adaptation du procédé à la nouvelle minéralogie et deuxièmement, l'accroissement du tonnage de 1800* à 4500 t/j. Aux circuits existants de broyage, de flottation du cuivre, de cyanuration et du charbon en pulpe, les circuits suivants furent greffés : broyage semi-autogène, flottation du zinc, manutention des concentrés (épaississage, filtration, entreposage et chargement automatisé), décantation à contrecourant et précipitation au zinc, destruction des cyanures et remblai en pâte. Cet article se veut une revue des différentes étapes du projet d'agrandissement du concentrateur qui se sont effectuées par phases progressives de 1997 à 2000. De plus, une description des nouvelles technologies sélectionnées et implantées est présentée.

May 1, 2001

By Chris Carr

This paper describes the process employed and the work undertaken to enable the surrender of the mine permit relating to the two tailings deposits at the abandoned Red Mountain Mine site near Rossland, BC. The first phase of the work undertaken was to provide urgent remedial work for protection of the environment, primarily through rehabilitation or replacement of surface water drainage systems. The second phase was to up-grade the water management systems to the appropriate level given their consequences of failure. The final phase of work is to ensure long term geotechnical stability of the facilities to the same level of risk. Establishment of a sustaining fund will facilitate long term monitoring and maintenance of the facilities.

May 1, 2002

By J. Kouam

Al-Si-Cu and Al-Si-Mg alloys are widely used in several applications. Although they can be produced near-net-shapes, products made of these alloys very often require some machining. The purpose of this study is to evaluate the machinability of A319 and A356 under TO and T6 conditions. The machinability was assessed using during dry drilling machining process and the machinability indexes used are the chip form, the chip breakability and the cutting forces. It is found that 319 and 356 exhibit different machinability behaviors, especially in the T6-condition in terms of forces requirements, chip breakability and chip segmentation. It is also found that both the microstructure of the workpiece materials and the machining conditions significantly affect the chip formation mechanism, and therefore, the machining parameters could be selected to promote a chip form that is easily manageable in production.

Jan 1, 2011