Search Documents

By Paivi Suikkanen, Kari Hietala, Kaarlo Haavanlammi

"Processing of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of platinum group metals (PGM’s) and cobalt are key issues of the Nickel Smelting technologies. PGMs are typically found in association with each other, but also importantly with nickel and copper. A challenge of producing saleable concentrates at acceptable recovery degrees, an increasing focus on the sustainable use of metals and recent decreases in the value of nickel has increased the interest to find a reliable route from Cu-Ni-PGM bulk concentrates to product. According to studies, most efficient process for Ni-Cu-PGM concentrates is flash smelting using DON process20 years ago, in 1995, Outokumpu commenced at Harjavalta a new Nickel Flash Smelting technology based on the Direct Outotec Nickel (DON) Smelting Process. The DON process enables production of high-grade nickel matte with low Fe-content directly in the Flash Smelting Furnace (FSF) without subsequent converting. Metal values from the smelting slag are recovered in the Electric Furnace (EF) as iron containing Ni-matte. Matte refining is based on atmospheric pre-leaching and total pressure leaching. Nickel, cobalt and iron are leached leaving a leach residue containing small amount of gangue minerals and PGM’s. Iron is removed from the leach solution in and nickel will be recovered with standard methods. Overall > 95% metal recovery can be expected with low energy consumption and low environmental impact."

Jan 1, 2014

The following briefing is intended to provide an overview of the present and future challenges associated with our access to a secure and adequate supply of electrical energy necessary to support safe, productive and sustainable mining initiatives at Musselwhite. Contents ??Site power demand vs. current available supply ??Supply technical deficiencies ?adequacy and security of present supply ??Present internal generation ??Anticipated future internal generation requirements ??Increased requirements necessary for planned expansion ?demand/security ??Goldcorp?s strategy to achieve required supply ?transmission line initiative ??Subsequent benefits to others from the Goldcorp initiative. ??Economic impact of MusselwhiteMine on the northwest region ??Anticipated economic impact of planned expansion ??Expected life cycle of MusselwhiteMine ??Comparative energy costs for similar operations in other jurisdictions ??Conclusions ??Anticipated action plan ??Energy Management Initiatives ??Site Orientation

May 1, 2009

By J. Olaf Sund

"THE November issue of the Bulletin carried in it ""Origin of the New Bruns1viclc Gypsum Deposits"" by J. Olaf Sund. This paper was a digested account of a Master's thesis at the University of New Brunswick which was a very useful compendium of information of gyp-sum in New Brunswick. It was a warded the President' s Gold .Medal and the First Prize in the Graduates' Section of the Students' Essay Competition. The present writer presents his congratulations to the winner of the competition. At the same time he must comment on the use of certain terms and on certain conclusions presented in the paper.The term ""unconformable"" has been used in several places in the paper to describe the relationship of gypsum to anhydrite in various deposits in New Brunswick in a sense which is quite alien to the accepted meaning. It has long been known tl1at the gypsum at the surface or near the surface in deposits in the Atlantic Provinces has come from hydration of anhydrite by surface and ground waters. The gyp-sum must be looked upon then as an alteration or even a weathering product. It cannot in this sense be called ""unconformable"" and thus arguments using the word in the accepted sense are invalid."

Jan 1, 1960

By R. J. Brailey

"A USER'S VIEW OF CONVEYOR WEIGH SCALESThe Sudbury Operations of Falconbridge Nickel Mines Limited includes seven mines, three concentrators and a smelter. The flow of ore, concentrates, fuel and fluxes between and within these plants requires measurement for accounting and control. The design, installation and maintenance .of weighing systems falls within the responsibility of the Instrumentation Department of Falconbridge Nickel Mines thus al lowing a common approach to conveyor weighing problems and the benefit of a common spares supply. This paper gives a brief overview of the recent experience with conveyor scales within the Sudbury Operations and discusses the problem areas.GeneralThe best way to establish the total amount of material going to or from a process is with a bucket and a stop watch. Unfortunately the flowrates involved in mining plants make the buckets very large, but wherever it is feasible static weighing is the preferred method of determining total quantity. This applies particularly to batch systems, where the material can be brought to rest long enough to allow a very accurate weight determination. Any form of weighing in motion is susceptible to variations in the forces of the transporting system. A belt scale is affected by its position on the belt, idler alignment, support stiffness, variations in belt tension, material spills and build-up, and a host of other factors all of which require careful consideration in any installation.As with instrumentation applied to any system the plant should be designed to ensure that the best results can be obtained from the equipment. This means getting the scale supplier together with the conveyor supplier as early as possible in the designing of a new plant. Any corners cut in scale installation will be paid for later in poor results and/or increased maintenance."

Jan 1, 1975

By Adriana Ramirez, Bradford C. Wesstrom, Blanca Olave

The Freeport McMoRan El Paso Copper Refinery optimizes electrolyte quality using a number of systems. The facility controls copper, arsenic, antimony and bismuth using electro-winning cells within the Tank House and Nickel Carbonate Plant Liberator Circuit (NCP). The NCP manages sulfuric acid content utilizing recycled electrolyte in the slimes autoclave as well as operation of the Acid Purification Unit, APU. The El Paso Refinery removes common sulfates using metal hydrolysis with sodium carbonate. Finally, a Mechanical Vapor Recompression, (MVR), at the water recovery plant removes sodium sulfate generated by the NCP. This paper will provide a summary of these operations. INTRODUCTION In the mid 1920’s Nichols Copper Company, in Laurel Hill, New York, recognized the need for a modern copper refining facility in the southwest. Because of the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the ideal location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Water is a precious commodity in the desert southwest, making conservation of this natural resource an important goal for the El Paso Operations. In the 1980’s, work on the treatment of slimes was improved through the use of pressure leaching of the refinery slimes using an autoclave. Due to the high tellurium content in the leached slimes solution, it was crucial to implement a method for its removal before the solution returns to the tank house electrolyte. A copper telluride cementation operation was installed for tellurium recovery and the ability for the recycle of the leachate and wash water to the refinery electrolyte. In October of 1997, ground was broken for the construction of the water recovery plant using an MVR to reuse process water, reducing water consumption by 25%. In 2002, electrolyte purification was further improved with the installation of an Acid Purification Unit, (APU) (Sheedy, Pajunen, & Wesstrom, 2007). The APU recycles 90% of the acids (both sulfuric and arsenic acids) back to the tank house electrolyte. The solution that passes through the APU is treated with soda ash to precipitate metals out of solution as carbonates and generates a sodium sulfate solution. This sodium sulfate solution is easily processed in the new water recovery plant, where the majority of the water recycles back into the plant as pure condensate. In 2012, the power plant at the refinery upgraded its Reverse Osmosis System to provide RO water to the tankhouse. This insured that the refinery would not have to bleed electrolyte for metals contained in well water such as: calcium, magnesium, iron and sodium chloride.

Jan 1, 2019

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By I. Mc Dougall, H. Joubert, G. de Villiers

The use of sidewall copper cooling systems to prolong furnace campaign life is becoming an accepted technology solution in the base metals industry. Tenova Pyromet has designed and installed a number of sidewall copper cooling systems in base metals furnaces, including the platinum industry. Apart from increasing the furnace campaign life through the formation of a stable freeze lining, a well-designed copper cooling system enables the plant operator to focus more on optimizing the process to achieve throughput and recovery targets, and to accommodate more varied and available concentrate feed blends. The paper discusses the design of sidewall copper cooling systems for copper smelting and converting furnaces to achieve the above objectives. More specifically, the design of copper cooling systems for top submerged lance furnaces are discussed. An overall increase in furnace heat losses has been raised as a concern for intensively cooled sidewalls. The paper explores the overall heat loss expectations for copper cooled furnaces versus traditional refractory lined furnaces. In addition, the potential use of alternative cooling media is discussed. INTRODUCTION Base metal smelting and converting furnace technologies have been evolving continuously over the past century to satisfy the need for higher throughput, improved efficiency, and longer campaign life. To accommodate these demands, in particular higher smelting intensity and throughput, furnace bath containment systems had to improve. The use of pure refractory lining systems has slowly made room for the use of more intensively cooled lining systems (Joubert, Nikolic, Bakker & Mc Dougall, 2016). These cooling systems evolved from external shell cooling, such as shower or film cooling, to copper plate coolers extending into the furnace refractory lining, and high intensity stave or panel coolers (Verscheure, Kyllo, Filzwieser, Blanpain & Wollants, 2006). Consequently, an increasing number of base metal smelting and converting furnaces are equipped with copper cooling systems, including flash furnaces (Bryk, Ryselin, Honkasalo, & Malmstrom, 1958; Yasuda, Motomura & Kawasaki, 2014; Marx, Shapiro & Henning, 2010), top submerged lance primary smelting and fuming furnaces (Bhappu, Larson & Tunis, 1994; Kim, Lee & Lee, 2000; MacRae & Steinborn, 2018), top submerged lance converting furnaces (Viviers & Hines, 2005; Nikolic, Hogg & Voigt, 2018), primary platinum smelting electric furnaces (Nelson, Stober, Ndlovu, De Villiers & Wanblad, 2005; Jones, 2005; Hundermark, De Villiers & Ndlovu, 2006; Mc Dougall, 2013), and electric slag cleaning furnaces (Joubert, Nourse, Masters & Hundermark, 2005).

Jan 1, 2019

By Patricia Dillon

EHS Management Standards Communication and Reporting (8) ! Establish processes for internal and external communications ! Designate responsibilities for communication with COI ! Report as defined by senior management ! Report annually to employees, shareholders, COI on EHS and social performance Community Rights and Public Consultation (9) !Identify COI?s and establish process to hear concerns !Acknowledge and respond to complaints !Support local communities !Plan for closure and conduct public consultation !New projects include identification of COI?s, concerns to be considered in design

May 1, 2004

By J. Drozdiak

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

Unplanned open stope hanging wall dilution is a significant cost for many open stope mining operations. Significant advances in empirical and analytical approaches for estimating stope dilution have been made, however, many important factors are still either ignored or assessed in purely subjective terms. There are many hard to quantify factors that simultaneously influence opening stability and dilution. This creates a significant difficulty for determining the influence of a single variable, such as exposure time, on opening stability. Open stope exposure time has been found to be one of the important factors that influences overall stope stability and dilution. A study is currently being conducted to quantify many of the factors influencing open stope dilution. The assessment of a large comprehensive case history database of Hudson Bay Mining and Smelting Co. Ltd. (HBMS) operations forms the basis of this study. This paper presents the findings of a study on the influence of stope exposure time on open stope dilution. The study is based on applying existing empirical stope dilution prediction methods to the extensive HBMS database. Minimising stope mucking time has been recognised as a method to significantly reduce stope dilution. Factors which influence hanging wall dilution, such as drill and blasting methods as well as undercutting the hanging wall, have been applied to reduce the scatter in the database. Empirical design techniques based on rock classification attempt to relate opening stability to ?stand-up time?, however, these approaches have not frequently been applied to the mining industry. Data from a ?stand-up time? graph have been interpreted in terms of an equivalent average depth of hanging wall slough and compared to the HBMS database findings. To add to the existing HBMS database, several stope case histories have been taken from Geco mine. These cases include data from very large open stopes with long exposure times. Data from all three sources suggest that hanging wall slough increases between .14 and 0.3 metres per month for a rock mass Q? value between about 4 and 13.

May 1, 2003

By Adrianus (Adrian) Halim, Tomas Bolsöy, Stina Klemo

"This paper describes the ventilation system used in underground hard rock mines in Sweden and Finland, which is very different than the system used in other major mining countries such as Australia, Canada, South Africa, and USA. The system utilizes auxiliary fans with Variable Speed Drive to distribute primary airflow to working levels instead of regulators that are commonly used in other countries. Descriptions about Ventilation on Demand in this system and ventilation regulations in Sweden and Finland are presented in this paper. This paper also quantifies a comparison between the Nordic and the system used in other countries. KEYWORDS Auxiliary fan, Regulation, Ventilation on demand (VOD), Variable speed drive (VSD) INTRODUCTION The primary objective of an underground mine ventilation system is to provide sufficient airflow to dilute atmospheric contaminants that are produced by mining activities. Typically, a mine ventilation system consists of one to four primary fans, regulators to control primary airflow distribution to levels or panels, and auxiliary fans that distribute airflow to dead-end workings via ducts. Depending on circuit geometry, underground booster fans are sometimes used. This system is widely employed in many countries such as Australia, Canada, USA, United Kingdom, and South Africa. However, mines in Nordic countries such as in Sweden and Finland employ a different system, in which auxiliary fans instead of regulators are used to control primary airflow distribution, as well as distributing airflow to dead-end workings. This paper describes the general layout of Nordic ventilation system, its VOD and heating system, its comparison with the system that is widely used in other countries which is referred as “Non-Nordic ventilation system” in this paper, and the current ventilation regulations in Sweden and Finland. The comparison was quantified by doing simulations using Ventsim Design 5 software. DESCRIPTION OF NORDIC VENTILATION SYSTEM General System Layout Figure 1 shows a schematic of typical ventilation system used in Swedish and Finnish mines. The schematic was drawn by Franzen, Myran, Larsson, and Rustan from Stiftelsen bergteknik forskning (Swedish Rock Engineering Research Foundation) and the English translation is written next to the Swedish terminologies. The system is generally a push-pull system. None of Swedish and Finnish mines use exhaust system. As shown in Figure 1, the primary airflow is distributed to levels by auxiliary fans that are bolted to a bulkhead located in the access to intake raise/shaft. These intake fans are attached to ventilation ducts that distribute airflow to all working faces. The exhaust auxiliary fans, which are not attached to any ducts and also are bolted to a bulkhead located in the access to exhaust raise/shaft, then flow the exhaust airflow into the exhaust shaft. A small quantity of this exhaust air is directed into the ramp, which acts as another main exhaust airway. The deepest level is also equipped with booster fan(s) that draw air from the intake shaft/raise and direct it into the ramp to provide fresh air in the ramp. There is no free split in this system. Figure 2 shows a schematic of a level ventilation layout in the Nordic system. Figure 3 shows a photo of these auxiliary fans."

Jan 1, 2019

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By Martin Encinas, Jesús L. Valenzuela, Jose R. Parga, Salvador Aguayo, Roy G. Lewis

Continuous laboratory solvent extraction of gold from cyanide solutions using LIX?79 guanidine based extractant has been investigated. Different variables that affected the selectivity and extraction include aqueous pH, extractant concentration, and modifier concentration. The extraction isotherms of the aurocyanide complex with respect to the other cyano anions were compared, and the following order of selectivity Au > Ag > Zn > Cu > Fe was observed. According to the pH isotherms, aurocyanide can be extracted in an alkaline media, and a better separation with respect to the other cyanoanions was obtained in the pH range 10.5-11.2. From the McCabe Thiele diagrams, better recovery was predicted when using LIX?79 extractant and tridecanol modifier at 10 vol.%. Stripping of the gold from the loaded organic was carried out at pH > 12 using NaOH and NaCN solution. The continuous tests indicate that a two-stage extraction followed by a single stage strip is adequate to obtain an overall process efficiency of >90%. Better results were obtained using a copper wash stage before gold stripping.

Jan 1, 2014

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By Jose Alberto Gonzalez, Said Sharif Mahboob, Jeffrey L. Shepherd

"During the industrial electrowinning of zinc, uneven growth can cause short-circuits and make the deposits more sensitive to the presence of impurities that can significantly impact current efficiency. To produce levelled zinc deposits, additives such as glue, licorice and sodium silicate are often added to the electrolyte. Even in the presence of additives, uneven zinc growth still takes place because of the combination of hydrodynamic and electrolysis conditions in the cell house. Recent advancements in imaging spectroscopy and scaling analysis have opened an avenue to further study the effects of additives on zinc growth morphology. In this study, Atomic Force Microscopy (AFM) and scaling analysis have been used to monitor zinc growth characteristics including roughness, periodicity, aspect ratios and growth mechanisms as a function of electrolyte composition as well as deposition time. Zinc was electrodeposited from an industrial electrolyte containing a host of additives onto an aluminum cathode with a platinum wire serving as the anode. AFM images of the samples were collected to obtain 3D topographical information on which scaling analysis was performed to extract details on root-mean-squared (rms) roughness, periodicity (grain size), aspect ratio of surface features and growth mechanism. This analysis provided information on the mechanism by which the previously mentioned variables can impact short term growth and also provided a prediction of expected growth at long deposition times.INTRODUCTIONElectrowinning is one of the final stages in the industrial production of zinc metal. It is during this process where dissolved zinc ions undergo electro-reduction from an acidic electrolyte onto an aluminum cathode and are later recovered by stripping the zinc metal from the substrate. However, due to the nature of zinc growth as well as the various operating conditions, zinc deposition may occur unevenly, sometimes causing short-circuits that can cause electrode damage and reduced zinc production."

Jan 1, 2016

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few – but very important – instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By Jessica Hurst, Mark Holdsworth, Jeff McKay

"In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart. INTRODUCTIONRio Tinto’s Kennecott Copperton Concentrator produces copper, molybdenum, gold and silver. The mill has 4 SAG mills (SAG 1-3, 34 foot diameter and SAG 4 36 foot diameter), 8 ball mills and copper and molybdenum flotation plants, as seen in Figure 1. The 2010 average data is shown in Table 1.In 2002, a Metso Cisa OCS Expert Control system was installed at Copperton for SAG and Ball mill advanced control. The expert control was first placed on SAG 2; data from the first few weeks compared with operator performance indicated approximately an 11 percent increase in throughput. After full commissioning, the system was gradually refined further by plant personnel to develop key performance indices based on SAG feed size, refinement of the sound setpoint for control of mill speed and throughput, specific rules to help the adjustment of speed based on loss of a feeder, etc. With the addition of the pebble crushing circuit, the expert control began utilizing a model estimation of crushed pebble bin level to help stabilize the impact of returned crushed and uncrushed pebbles on the SAG mills. As the ore and limitations change, it is necessary to evolve the SAG logic to better handle any constraints."

Jan 1, 2012

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By D. E. Ayres, J. Farstad

"The Midwest uranium deposit is located within the Athabasca Basin near its eastern margin and displays many of the features seen in a number of other similar deposits in this area. The mineralization occurs in the vicinity of a tectonically disrupted portion of the unconformity separating the clastic sedimentary rocks of the Helikian Athabasca Group from Aphebian pelitic meta-sediments which are equivalent to the basal pelitic meta-sediments of the Wollaston Group. The orebody consists of pods of massive pitchblende and sulphur-arsenides within an elongate and tablular envelope of disseminated and fracture controlled mineralization. The massive pods are intimately associated with overbank mudstones of the lowermost Athabasca Group. Both structure and lithology have played major roles in localizing the deposit as follows:1. The basement lithology influenced the mineralogy of the regolith produced on the pre-Athabasca unconformity.2. The style of clastic deposition and the character of the regolith on this unconformity favoured local preservation of mudstones.3. The basement lithology influenced the location of zones of post-Athabasca faulting.4. The proximity of these fault zones to mudstones provided for the coincidence of circulatory channels for fluids bearing uranium, with a good precipitant for the metal.IntroductionA brief summary of the geology of the Midwest uranium deposit was presented by J. Farstad (1979) to the attendees of the Saskatchewan Potash and Athabasca Basin uranium deposits field trip organized by the Canadian Institute of Mining and Metallurgy (May 28 to June 1, 1979). Since that time a substantial amount of data has been collected and studied. This paper is a precis of a report by J. Farstad (1981) which summarizes the geology of the deposit as inferred by visual examination of diamond drill core, augmented by information obtained from detailed examination of selected cores by D.E. Ayres."

Jan 1, 1986